drill grinder used for sale

bore capacity in steel (diameter): 16 mm throat: 170 mm bore stroke: 50 mm : 16 mm spindle taper: MK2 spindle turning speed range: 50 - 2250 U/min : 320 mm : 145 mm table surface area: 500 x 140 mm connected load frequency: 230 V total power requirement: 0,5 kW weight of the machine ca.: 90 Kg dimensions of the machine ca.: 0,5 x 0,45 x 0,84 m Drilling and milling machine with - variable spindle speed - Digital depth display - Left / right switch - Cross support - swiveling spindle head - Feeds via hand crank - Tool case with content but without digital display The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding range: 2 - 20 mm sharp cornered angle min./max.: 90 - 135 Grad connected load: 230 V weight of the machine ca.: 8,6 Kg dimensions of the machine ca.: 0,35 x 0,2 x 0,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 14 mm Boring power: 15 mm : MK 2 bore depth: 70 mm throat: 180 mm : bis 275 mm : 529 mm table surface area: 250x220 mm column diameter: 65 mm Total height: 890 mm total power requirement: 0,6/1,0 kW : 420-2100 U/min. weight of the machine ca.: 63 kg Machine with CE mark! new machin Domestic equipments: - Stepless speed control - Table adjustment via rack - Digital speed display - Full motor protection - drill protection The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Universal screwdriver, construction screwdriver, screwdriver, electronics screwdriver, hand drill -Nominal input: 740 watts -Max. drill bit: Ø 13 mm -Connection: 220 volts Quantity: 1 available -Dimensions: 450/210/H80 mm -Weight: 4.3 kg/piece

Rotary hammer, chisel hammer, combination hammer, Bosch hammer, impact drill, chisel hammer -Nominal consumption: 500 W -Drilling/hammer drilling -Speed: 0 - 2200 rpm -Dimensions: 290/80/H200 mm -Weight: 2.2 kg

: 0 bore depth: 10000 mm number of spindles: 0 Control: Siemens Simatic Touch SPS swing over bed: 1050 mm swing diameter over bed slide: 1600 mm boring diameter: 50 - 310 mm centre height: 800 mm speeds:: 2,5 - 400 total power requirement: 74 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 55 mm : M 30 : M 36 : MK 4 spindle turning speed - stepless: 70-1.200 U/min spindle stroke: 140 mm throat: 300 mm column diameter: 145 mm : 615x430 mm distance spindle /table: min./max. 150/735 mm : 2 x 14 x 224 mm feed: 0,1 + 0,3 mm/U Machine height: 1850 mm weight: 380 kg drive motor: 1,8/2,9 kW Standard equipment: - Lockable main switch with motor protection switch - Mushroom pushbutton (latching) for EMERGENCY STOP - Infinitely variable speed adjustment - Digital speed display - Feed overload protection - Protection class IP 54 - Spindle protection with electrical fuse Item 20.1 Thread cutting device with foot switch, for thread cutting with Stop, max. 6 threads / min., (Thread cutting performance dependent on spindle speed) ! NEW FOR YOU AS A SERVICE ! Machine leasing up to 60 months without down payment, without residual value, personal advice and individual leasing rate calcu ...

bore capacity in steel (diameter): 23 / 28 mm throat: 260 mm bore stroke: 120 mm tool taper: MK 3 table-size: 500 x 350 mm column diameter: 100 mm total power requirement: 1,3 kW weight of the machine ca.: 400 kg dimensions of the machine ca.: 800 x 600 x 1750 mm Defective feed! Right-left rotation stepless speed adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Magnetic drill, hand drill -Magnetic base: Magnetor type PS 32 L -Drilling machine: AEG type HBE-IV - Recording: MK2 -Max. Drill: Ø 23 mm -Connection: 265V/200Hz -Dimensions: 700/300/H670 mm -Weight: 49 kg

two-armed drill, rotary drill, magnetic drill, impact drill, two-hand drill -Taper: MK with drill chuck -Nominal consumption: 250 W -Connection: 220 volts -Max. Drill: Ø 15 mm -Dimensions: 420/420/H120 mm -Weight: 7.1 kg

drill diameter: 1,5 - 25 mm lip angle: 40 - 180 ° 6-jaw-chucks: various equipment: manual included: Encapsulated drive motor: closed version, air-cooled, rotary and AC drills with cylindrical or conical shank left and right-hand drills 6 Jaw chuck Device for compressed air cooling various equipment (see pictures) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Multi-spindle head, multi-spindle drill head, drilling gear -Multispindle head -Spindles: 4 -Socket: Ø 20 x 30 mm -Dimensions: Ø 120/165 mm -Weight: 2.2 kg

Multi-spindle head, multi-spindle drill head, drilling gear -Multispindle head -Spindles: 7 -Socket: Ø 20 x 30 mm -Number: 2x built-in drill -Dimensions: Ø 120/290 mm -Weight: 2.2 kg

Reamer, twist drill, drill -Twist drills: different sizes on request -different manufacturers -Price: Ø 10 - 30 mm 0.50 EUR/mm (drill Ø 20 mm = 10 EUR net) -Price: Ø 31 - 45 mm 1 EUR/mm (drill Ø 35 mm = 35 EUR net) -Price: Ø 46 - 80 mm 1.60 EUR/mm (drill Ø 50 mm = 80 EUR net) -Two-cutter -Diameter: 10-80mm -different lengths -Recordings: MK1 - MK6 -Type: HSS

Multi-spindle head, multi-spindle drill head, drilling gear -Piece multi-spindle head: 3 -Spindles: 2, 3 4 -Socket: Ø 20 x 28 mm -Price: complete -Dimension: see pictures -Weight: 7 kg

bore capacity in steel (diameter): 40 mm throat: 293 mm bore stroke: 120 mm spindle taper MT: 3 column diameter: 115 mm table surface area: 514 x 360 mm spindle turning speed - stepless: 160 - 2250 U/min total power requirement: 1,0/1,6 kW weight of the machine ca.: 0,285 t dimensions of the machine ca.: m Condition: new / unused: The machine can be viewed under current.: 37981 400 V, 50 Hz, colour: light grey RAL 7035 continuous speed control, digital speed indication, push button for emergency switch off, turning switch for clockwise/counterclockwise rotation, motor protection switch, IP 54, connecting plug, finish: structure varnish, new spindle bearing, new step pulleys, belts aso. operation manual, wiring diagram. Machine has been checked in our workshop, including electr. testing report. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: - Drilling capacity in steel ST 60 30 mm - Drilling spindle holder MK 3 - 4 feeds 0.1 - 0.16 - 0.25 - 0.4 mm/U - Drilling spindle speeds in gear stages 95 - 2000 rpm - Right - Left - Drilling spindle stroke 160 mm - Projection 350 mm - Table with 3 T-slots height-adjustable 340 x 320 mm - Table can be tilted left + right - distance table – drilling spindle 500 mm - distance machined base plate – drilling spindle 1050 mm - Column diameter 160 mm - Lighting - Coolant device - Drive 400 V / 2.4 kW - Space requirement approx. W 600 x H 1950 x D 800 mm - Weight approx. 350 kg

1 x used double-sided Rotoles S600 with 2 grinding units and 1x brush Working width 600mmm Speed 60m/min Calibration milling planing machines with feed rollers Best accuracy of the boards and excellent results in delamination attempts, at any speed. ROTOLES S calibration machines are the best choice for calibrating boards and slats before gluing. Rotoles S calibration milling planing machines with feed rollers Best accuracy of the boards and excellent results in delamination attempts, at any speed. ROTOLES S calibration machines are the best choice for calibrating boards and slats before gluing.

bore capacity in steel (diameter): 50 mm arm length: 1500 mm workpiece height max.: mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 1610008 Type of machine Radial drill Make MAS Type VO 50 Admision in drilling spindle MT 5 Max. drill capacity 50 mm Base dimensions 1820 x 986 mm Speeds (Rpm) 28 - 2500 Feeds (mm/R) 0,5 - 2 Lenght (mm) 3250 Width (mm) 1120 Height (mm) 3396 Weight 4550 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

spindle diameter: 100 mm x-travel: 1200 mm y-travel: 800 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: 5,6x3,4x3,x7 m Brand: Femco Type: WBT-100SR2 CNC brand: Mitsubishi CNC model: Meldas C3 Year of make: 1995-05 Facing support Table length: 1.440 mm Table width: 1.600 mm Spindle diameter: 100 mm ø Machine dimensions (lxwxh): 5.680 x 3.400 x 3.700 mm incl. right-angle milling head type Huron The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Milling machine DECKEL MAHO DMG 125

End Milling Machine Drill Milling Machine working width mm: 3200 Left - right swivelling saws from 0° - 45°. Complete with drilling unit Suitable for machining doors and door posts.

spindle diameter: 105 mm x-travel: 1000 mm y-travel: 1000 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Brand: Juaristi Type: MDR105 CNC CNC brand: Heidenhain CNC model: TNC145 Year of make: 1983 Table length: 1.000 mm Table width: 1.000 mm X: 1.000 mm Y: 1.000 mm Z/W: 1.000 mm Spindle taper: ISO 50 Spindle diameter: 105 mm ø The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Drill stand, drill stop, drill press stand, drill jig, drill bushing jig -Quick release device -Max. Height: 100mm -Dimensions: 400/240/H220 mm -Weight: 22 kg

Rapid radial / Rapid radial / Snel radial DANUBE DR 13

Year of construction construction 1983 Drive power Drive power 83 kW Clamping table Clamping table 2500 x 2500 mm workpiece mass on table Workpiece mass 20 t Processing width on table 5770 mm Processing height on table 2800 mm processing depth 1985 mm Spindle diameter Spindle diameter 200 mm Slide cross-section Slide cross-section 530 x 550 mm Additional equipment Angle head large Angle head small

Giana lathe mod. GFP14 - 710x 5300 - year 2007, control FAGOR GFP14

Webo in-line drilling machine - 2 machines: speed 90 - 1000 1/min. - 4 machines: speed 4000 - 6000 1/min. - Coolant device - Tool holder: MK2 - Width: 200 cm - Height: 200 cm - Depth: 100 cm Good condition fully functional can be visited and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article, in order to avoid misunderstandings, can be viewed before the purchase and tested under electricity. Please ask questions before buying to avoid ambiguity. For general questions or an appointment for a viewing, I can be reached at any time at the telephone number below or above. Errors in the description and prior sale excepted. VAT will be shown separately on my invoices. Shipping with freight forwarder.

Тип: Z4A Число осей/ шпинделей Доступны различные варианты головок 4x3 Расстояние между крайними шпинделями 2300 mm Регулируемая скорость сверления Высота стола от пола 840 mm Размеры стола 600x2350 mm Число прижимов 8 Мощность двигателя 6 kW(4x1,5) 400 V Скорость двигателя 2840 r.p.m Необходимое давление воздуха 6-8 bar Вес 425 kg Размеры для транспортировки 2450x960x1550 mm

Paper drilling machine Nagel Citoborma 280 AB

Workbench drilling machine FLOTT TB 6/I, II, III One-piece spindle - male cone B12 Manual spindle exit: 65 mm Speed: from 450 to 9000 RPM Throat depth: 160 mm Mini height in low position: 60 mm Max height in height position: 180 mm Head rotation around the column Voltage: 380 V Width: 300 mm Depth: 600 mm Total height: 700 mm Weight: approx 70 kg

Drill press, drill press, stand drill, pillar drill -Table size: 430 x 615 mm -spindle taper: MK4 -Projection: 365 mm -Speeds: 63-800 rpm -Spindle stroke: 195 mm -Transmission -Feed: 0.1-0.4 mm/rev -Water cooling -Dimensions: 730/1040/H2640 mm -Weight: 1026 kg

diamond core drilling machine -Drill stand -vacuum pump -Core drill: Ø 202 mm (picture) -Machine dimensions: 500 x 370 x H1070 mm -Weight: 53 kg

High precision drilling and milling machine Aciera 22 VA Good condition from school operations Year of construction approx. 1990 Table 600 x 320 mm Speed 40 - 3600 rpm Speed setting rpm 4 automatic feeds 40-280 80-560 275-1800 550-3600 Spindle diameter 65 mm Drilling spindle stroke 120 mm Spindle holder: Aciera quick-change system Automatic thread cutting Drilling capacity in solid material 25mm Max drilling capacity up to 30mm Height adjustment via hand crank Motor: 1.1 KW Lamp Some quick-change shots Dimension WxDxH 90 x 130 x 185 cm Weight approx. 800 kg Technical information subject to reservation

Manufacturer/ Make: SKODA Typ/ Type: W200 Year of construction/ year: 1987 X-way: 11500 mm Y-way/ Y-way: 4500 mm Spindle diameter: 200 mm

I sell a Top Dubel drill multi-spindle drill Detel M-13, built in 2007. 3-spindle See good condition. Available the same.

Multi-stand drill Prior sale reserved - errors possible Internal Reference Number: D-1143-1

May SS80 U Machine can be visited by arrangement under power

I sell an Angular drill with hanging insert suitable for tur production. MARZANI MACCHINE CHEAP WORK Year of construction: 1993 Number of drilling spindle 1 (drill head fully -7 to +90° adjustable) Number of insert heads 1 (magazine suitable for turret hanging) Insert head mechanical, screw insert Very good condition. Available the same.

- Infinitely variable speed control - Quickly adjustable drilling depth stop - Thread cutting device - Undervoltage triggers - Table height adjustment via rack - LED lighting in the head - Continuous/normal drilling capacity R1: 23/25 mm - Thread cutting performance (depending on slope) R1: max.M 16x1 - Spindle MK II - Drilling depth 100 mm - Projection 260 mm - Column diameter 110 mm - Usable table surface (W x L) 420 x 340 mm - T-slot size (arm): number 2, distance 125 mm - Speed display digital - Drilling depth display digital - Drill depth stop quickly adjustable - Feed by hand - Motor three-phase current 400 V - Spindle speeds infinitely variable R1 with 20-2,000 1/min Option: Coolant device: € 525,- FACTORY WARRANTY: 3 years DELIVERY: free domicile incl. packaging NOT THE RIGHT MACHINE? WE ALSO CARRY OTHER FLOTT PRODUCTS - ASK FOR A QUOTE! FAS ...

Radial Drilling Machine NOVISA NTR 1600 Spindle: CM5 Spindle exit Travel: 350 mm Spindle speed: from 25 to 1900 RPM Arm travel: 1600 mm Mini height in low position: 800 mm Max height in height position: 1500 mm Lubricant pump Voltage: 380 V Dimensions (L x W x H): 2600 x 1200 x 3000 mm Weight: approx 4 T

Kramatorsk Model KJ1910 serial number 1913 Swing Over Bed: 1600mm Maximum Workpiece Length: 6300mm Maximum Drilling Diameter: 991mm Spindle power: 125.00kW Spindle Speed: 1 - 320 RPM Infinitely Variable power Existing Additional Chuck workholding range: 200 - 1250mm diameter, workpiece weight capacity using two open roll supports: 60,000kg, size range in closed backrest: 200 - 800mm, size range in open backrest: 630 - 1380mm, pressure head speed range: .125 - 500 infinitely variable, pressure head spindle bore diameter: 182 mm, pressure head motor power: 75kW DC, headstock speed ranges: 3, pressure head speed ranges: 2 Machine Length: 22950mm Machine Width: 4375mm Machine height: 2670mm Weight: 101091kg Condition Good

New VDL 2D chiseling machine with the possibility of automatic drilling at distances of 25 and 32 with the possibility of tilting and turning in 2 directions. Technical parameters: Control of the machine with 1 lever Power of the main motor: 1.5 kW Tool speed: 2850 rpm Spindle diameter: 3 - 16 mm Stroke of the spindle: 180 mm Dimensions of the table: 600 x 450 mm Weight of the machine: 320 kg

Drill press, drill press, stand drill, pillar drill -Table size: 500 mm -spindle taper: MK4 -Projection: 400 mm -Speeds: 38-750 rpm -Feed: 0.08-0.13 mm/rev -Columns: Ø 220 mm -Spindle stroke: 235 mm -Transmission: -Dimensions: 640/1020/H2730 mm -Weight: 965 kg

Reamer, twist drill, drill bit, spiral countersink, three-flute, twist drill -Three-edged -Diameter: 28-40 mm -Recording: MK3 -Type: HSS -Quantity: 37 pieces -Sale/Price: only complete set -Weight: 50 kg

bore capacity in steel (diameter): 35 mm throat: 230 mm bore stroke: 125 mm spindle taper: ISO 40 spindle turning speed range: 115 - 1750 U/min : 560 mm : 175 mm table surface area: 1000 x 240 mm max. distance between table and spindle-nose: 375 mm connected load frequency: 400 V total power requirement: 0,85/1,5 kW weight of the machine ca.: 0,95 t dimensions of the machine ca.: 1,3 x 1,2 x 2,1 m Domestic equipments: automatic feed and handwheel. Drill chuck with MK4 holder Digital depth display Left / right switch. Emergency stop switch Pivot head swiveling Spindle protection. Small toolbox Machine base and X-axis feed optional. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Standard equipment - Thread cutting device - Control panel with OLED display - robust, high-quality drill head hood - LED lighting - quickly adjustable and ergonomic drilling depth stop - infinitely variable speed control via rotary knob - thermal overload protection - Spindle stop - Drilling protection with electr. Hedge - Connection cable with CEE plug - mechanical feed of the Z-axis - incl. electromagnetic coupling for 3 feed speeds - Drill cross with push button - in thread cutting mode: right-left SPECIFICATIONS Continuous/normal drilling performance (mm) R1 - 27/32 (in E335/ST60) (100) R2 - 25/30 (in E335/ST60) (70) R3 - 30/35 (in E335/ST60) (200) Thread cutting capacity max.: R1= M24x3, R2= M20x2.5, R3= M30x3.5 Spindle MK III Drilling depth: 125 mm Projection: 300 mm Column diameter: 125 mm Usable table surface (W x D): 590 x 450 mm Speed display digit ...

Precise and heavy machine for drilling slotted holes. The maximum hole length is optional. In the standard version, it is 400 mm. The tool is fixed. The height is adjusted by raising the work table. Spindle power: 1.5 or 2.2 kW

2 Head Paper Drilling Machine

Universal screwdriver, construction screwdriver, screwdriver, electronic screwdriver, hand drill -Nominal consumption: 650 watts -Max. Drill: 6 mm -Connection: 230 volts -Weight: 2 kg