double side maschine used for sale

Panel thickness: 12 - 60 mm Feed speed: 18 m/min Edge thickness: 0,3 - 3 mm for coil edges Equipment: Programmable fence at the infeed Squaring device: 2 x 3,0 KW Glue application unit: A34 double edge magazine for 2 coils Lateral pressure rollers, thickness programmable, 1 driven, 2 non-driven rollers End trims HL84/85, programmable change straight/chamfer, 2 motors 0,18 kW Rough trimming: 2 x 0,55 KW Contour trimming FK 13, 2 x 0,55 KW Profile scrapers PN10 Flat scrapers Buffing unit Controlls: HOMATIC NC21

I sell the four-side planer Futura P-MAX 23/5+UNIV, built in 2008. 6 Spindle: bottom - right - left - top - bottom - universal Electronic programming for working width, working height and feed speed. Element max. 230x170mm ! All 6 spindles 6000 rpm. Material prints for short elements. Weight 2500kg. 1-zone pneumatic material pressure system for feed Fully operational. Available the same. Exhibition machine, has worked very little !

Control cabinet, distribution cabinet, control cabinet, TS modular cabinet, profile door -Side door -Dimensions: 1980/635/H40 mm -Weight: 26 kg

Vehicle: • Make: Nissan – machine overhauled 2023 • UVV Audit 11-2023 • Type: EGH02 F30U • Drive type: Diesel • Engine: Nissan 4 cyl. • Transmission: Automatic • Load capacity: 3000 kg • Load center: 500 • Lifting height: 3300 mm • Hours: 6557 • Internal no.: 03122023 Mast data: • Mast: Duplex with free lift and side shift • Lifting height: 3300 mm • Fork carriage: 1200 mm • Fork length: 1200 mm • Fork width: 100 mm • Fork thickness: 50 mm Dimensions: • Length: 2530 mm • Width: 1120 mm • Overall height: 2050 mm • Weight: 4390 kg Battery: NEW Tyres: • Front tyres: solid rubber tyres • Rear tyres: pneumatic tyres Attachments & special equipment: - Longer forks are available at an additional cost - Operating instructions available Extras: Preparation for road approval Mirror 3 Auxiliary h ...

Max. slider force at the distance of 12,5 mm in the lower dead point: 1250 ton Slider force at the distance of 250 mm in the lower dead point: 350 ton Number of single strokes per minute: 11 Slider stroke: 630 mm Slider adjustment: 630 mm The closed height: 1165 mm Table pillow: -Max. stroke: 250 mm -Stroke adjustment: 250 mm -Max. holding force: 250 ton -Max. ejection force: 40 ton Table dimensions: 4000x1800 mm Bolster dimensions: 3950x1800 mm Table gap: 3750x1300 mm Main motor power: 132 kW Stay spacing: 4000 mm Press weight: 215000 kg

I sell the four-sided planer FUTURA PRG24/7, Year of construction 2005. Element size max. 260x150mm ! 7 Spindle Configuration: Bottom 7,5kW (10HP) / 6000 rpm Right 7,5kW (10HP) / 6000 rpm Left 7,5kW (10HP) / 6000 rpm Top 7.5kW (10HP) / 6000 rpm Top 6.75kW (9HP) / 6000 rpm Right 6,75kW (9HP) / 6000 rpm Universal 7,5kW (10HP) / 6000 rpm Combined power 62KW / 102 A Weight 4500kg. Element size max. 260x150mm ! 2 FABA planing heads with spiral knife fi.140x260x40mm included in the price. Electronic programming for working width, working height and the height of pressure zone Feed speed adjustable with inverter. 2-zone pneumatic material pressure system for feed Available the same.

Part Number 6322 TECHNICAL DATA - max width of the workpiece 260mm - max height of the workpiece 160mm 6 spindles: 1) horizontal bottom 260mm 7,5kW 2) vertical right 160mm 7,5kW 3) vertical left 160mm 7.5kW - 3 spindles electrically adjustable front/rear 0.4kW 4) horizontal top 260mm 11kW - 4 spindles electrically adjustable up/down 0.4kW 5) horizontal bottom 260mm 7,5kW 6) universal 230mm 7,5kW - universal spindle electrically adjustable up/down - all spindles adjustable up/down, right/left - all spindles equipped with an electric brake - spindle diameter 1,2,3,4,5 50mm - universal spindle diameter 40mm - from above 6 pulling, toothed, metal, torsional introductory shafts, including 2 double - from above 5 pulling leads shafts, rubber, smooth including 3 double - from the bottom from the side of the pressure on the inlet - from below 2 pulling, metal, toothe ...

Part Number 6338 TECHNICAL DATA - max width of the workpiece 230mm - max height of the workpiece 160mm 7 spindles: 1) horizontal bottom 230mm 5,5kW 2) vertical right 160mm 5,5kW 3) vertical left 160mm 5.5kW 4) horizontal top 230mm 7,5kW 5) horizontal upper 230mm 7,5kW 6) horizontal bottom 230mm 7,5kW 7) universal 360° 230mm 7,5kW - all spindles adjustable up/down, right/left - spindle diameter 40mm - all spindles equipped with a brake - spindle speed 6000rpm in advance: - 6 pulling, toothed, metal introductory shafts, including 2 double - 4 pulling shafts, rubber including 1 double - 3 clamps on the lead bottom: - pressure from the side on the inlet - introductory shaft, toothed, pulling, swivel in the lower table top - 3 pull rollers, metal, smooth - pneumatically adjustable shafts - length of the introductory table top 1190mm - central lubricati ...

Part Number 6368 TECHNICAL DATA - max width of the workpiece 230mm - max height of the workpiece 130mm 7 spindles: 1) horizontal bottom 230mm 5,5kW 2) vertical right 130mm 5,5kW 3) vertical left 130mm 5.5kW 4) horizontal top 230mm 7,5kW 5) horizontal upper 230mm 11kW 6) horizontal bottom 230mm 18,5kW 7) universal 230mm adjustable at 360 degrees 5.5kW - all spindles adjustable up/down, right/left - all spindles equipped with an electric brake - spindle diameter 40mm - spindles 4 and 5 electrically adjustable up/down - from above 8 metal pulling introductory shafts, swivel including 2 double - from above 4 pulling rollers, rubber - pressure from above 2pcs - from the bottom of the ratchet - from the bottom from the side 3 clamps - from below 2 metal rollers, smooth, pulling - from the bottom 2 double rollers, pulling, rubber - pneumatically pressed shafts ...

Part Number 6393 TECHNICAL DATA - max width of the workpiece 200mm - max height of the workpiece 150mm - number of spindles 4: 1) horizontal bottom 200mm 5,5kW 2) vertical right 150mm 4kW 3) vertical left 150mm 4kW 4) horizontal upper 200mm 5,5kW - all heads adjustable up/down, right left - spindle diameter 40mm - spindle speed 6000rpm in advance: - pulling introductory shafts, toothed 6 pcs including 2 double - 1 pulling shaft, rubber bottom: - introductory shaft toothed, pulling, torsional in the lower table top - side pressure 3pcs - lead roller, pulling, metal, smooth - all pneumatically pressed rollers - length of the introductory table top 2130mm - table top adjustable up / down - central lubrication - electrical setting of planing thickness - lifting motor 1,1kW - smooth regulation of the feed speed on the inverter - feed motor 3kW - feed  ...

HEMINGSTONE JP-40SE-SV Year 2002 Side sealing machine Bag size - Width 900 mm , Length 200-900 mm Available bottom sealing bar

Longitudinal X: 2600 mm Cross Y: 700 mm Vertical Z: 700 mm Positions ATC: 12   CNC Brand: Heidenhain CNC Model: iTNC 530 X – Travel:               2.600mm Y – Travel:               700mm Z – Travel:               700mm A – Axis:                 360000° B – Axis:                 +/- 110 ° Table Length:             2.900mm Table Width:              700mm Table load:               2.150Kg Table  Ø:                 750mm Feed rate X-Axis:         40.000mm/min. Feed rate Y-Axis:&n ...

Panel thickness: 8 - 50 mm Thickness of the edges: 0,4- 3 mm Feed speed 8 - 11 m / min PU pressure rollers Equipment: Non-stick spray system Squaring unit, 2 motors 2,2 kW Panel edge heating Edge magazine for coil and strips Hot melt application with roller Airtec AT4510 unit The Airtec aggregate is positioned so you can use Airtec or the standard glue pot Motorized side pressure unit End trims, 2 motors, pneumatic positioning straight and with chamfer trimming unit above / below Contour trimming unit Profile scraping unit Glue scraping unit Polishing unit Detergent spray system central lubrication Powertouch control

I sell the moulding heads for the automatic fourside moulder WACO Weinig Gruppe. Inside diameter 50mm Outside diameter (with knives) 170mm Body diameter 155mm 15 pcs. working length 200mm (without knives). 8 pcs. working length150mm (with knives) Each with Hydro holding. Price per pc. 500 euros. Sellable per pc. or totally together. Available immediately.

Heavy high-performance planer designed for maximum feed performance and productivity. Designed for rough use in planing and sawmills. Suitable for the processing of planed goods and slats. Special features: Left version. for wood widths up to 360 mm. Machine we sell as used. But the machine never ran. Electrical part still has to be built by Ledinek - here adjustments are possible (axe positioning, FU-s, 400V or 480V etc.). Price is for the variant in the PDF description. Adjustments on request. Drive motors available.

ORDER NO. 6575 TECHNICAL DATA - max width of the workpiece 230mm - max height of the workpiece 170mm - 7 spindles: 1) horizontal bottom 230mm, 11kW 2) vertical right 170mm 3) vertical left 170mm (2 and 3 spindle), 11kW 4) horizontal right 170mm, 5.5kW 5) horizontal upper 230mm, 11kW 6) horizontal bottom 230mm, 7.5kW 7) universal 230mm, adjustable at 360°, 7.5kW - all spindles adjustable up/down, right/left - spindle 3 and 5 electrically adjustable - ATS - spindle diameter 40mm - electric brakes - from above 4 pulling introductory shafts, toothed including 1 double - from above the introductory roller pulling rubber double - from above the shaft leading out, pulling, rubber, double - from below 2 metal rollers, pulling, smooth - pulling roller, rubber, double - feed on cardan rollers - pneumatically pressed shafts - smooth adjustment of the feed spe ...

15.2 Kw, equipped with 2x easy touch screen (with adjustable/programmable recipe menus + cleaning mode), electric valve height adjustment, stainless steel housing,

Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...

Load: 4.5t, lifting height: 3800mm, battery weight: 1.95t, weight: 7.39t, operational hours counter: 26h.

Load capacity: 1400kg, load capacity with COG (load center of gravity): 600mm, Lifting height: 6510mm, weight: 3356kg. Including one defective battery. Forklift in working order without UVV. Documentation available. On-site inspection is possible.

Cantilever rack, heavy-duty rack, single-sided cantilever rack, pallet rack -Cantilever rack: one-sided, 5 bays H/W/D 4000/5150/1970 mm -Cantilever arms: 3 levels / shelf height: adjustable -Cantilever arm length: 1970 mm -Arm load: 700 kg / stand load 2100 kg -Total weight: 1700 kg

Cantilever rack, heavy-duty rack, single-sided cantilever rack, pallet rack -Cantilever rack: one-sided, 8 bays H/W/D 5000/8120/1970 mm -Cantilever arms: 4 levels / shelf height: adjustable -Cantilever arm length: 1970 mm -Arm load: 700 kg / stand load 2800 kg -Total weight: 3300 kg

Specifications: System: SSI Schäfer Type: K-SW-4300 Included in delivery are: 01x side bolster, second choice Length: approx. 4,294 mm Profile type: C115/22/2 C-profile: approx. 115 x 22 x 2 mm Unit weight: approx. 13.23 kg Information: - for KDR levels in PR and WR systems by SSI Schäfer for the inclusion of Longitudinal & transverse profiles as well as roller strips - also suitable with kink - can be used both inclined and in scales

CATALOG NUMBER 6679 TECHNICAL DATA - max width of the workpiece 250mm - max height of the workpiece 170mm 6 spindles: 1) horizontal lower 250mm 5.5kW 2) vertical right 170mm 5.5kW 3) vertical left 170mm 5.5kW 4) horizontal, upper 250mm 7.5kW 5) horizontal lower 250mm 7.5kW 6) universal 250mm, adjustable at an angle of 360 ° 5.5kW - 6 electrically adjustable spindle up / down - all adjustable spindles up / down, right / left - diameter of the spindles 40mm - 6 introductory pulling rollers, toothed, including 2 double ones - 6 rollers leading out, pulling, rubber, smooth, including 2 double - 2 clamps from above - from the bottom, a roller introducing toothed, pulling, torsion in the table before the first spindle - at the bottom, 2 pulling rollers, metal, smooth - 4 side clamps at the bottom - feed on cardan shafts - pneumatically pressed rollers - smooth regulati ...

CATALOG NUMBER 6674 TECHNICAL DATA - max planing width 150mm - max planing height 130mm 7 spindles: 1) horizontal lower 150mm 3kW 2) vertical right 130mm 3kW 3) vertical left 130mm 4kW 4) horizontal upper 150mm 4kW 5) horizontal lower 150mm 3kW 6) vertical right 130mm 4kW - diameter of all spindles 35mm - all adjustable spindles up / down and right / left - from above, 4 pulling rollers, toothed - 4 rubber, pulling rollers from above - 2 clamps from above - electric adjustment of the planing thickness of 0.25kW - length of the introductory top 1970mm - central lubrication of the table top - smooth regulation of the feed speed - 1.5kW feed motor - diameters of the extraction ports 6x120mm - dimensions length / width / height 4000x1300x1600mm - weight about 3000 kg - German production - for 6 heads - used planer, very good condition Net price: PLN 36900  ...

CATALOG NUMBER 6651 TECHNICAL DATA - max width of the workpiece 220mm - max height of the workpiece 120mm - 4 spindles: 1) horizontal bottom 220mm 4kW 2) vertical right 120mm 4kW 3) vertical left 120mm 4kW 4) horizontal upper 220mm 5.5kW - all adjustable spindles up / down, right / left - diameter of the spindles 40mm - from above, 4 introducing rollers, toothed, including 2 double ones - from above, 1 pulling roller, smooth, rubber - rubber, pulling roller at the bottom - pneumatically pressed rollers - feed on cardan shafts - 1.1kW feed motor - 0.37kW lifting motor - electric adjustment of the planing thickness - length of the introductory top 1980mm - side pressure - smooth adjustment of the feed speed 8-16m / min - central lubrication - diameter of the extraction port 5x140mm - locked in the cabin - dimensions length / width / height 3400x1500x1700mm - wei ...

Heavy four-sided combined calibration milling planing machine with additional scratch saw for relief grooves Still in operation at Franz Kirnbauer KG Hauptstrasse 2 AT-2630 Ternitz Detailed technical description in the PDF document (as an attachment in the photo gallery).

Order No. 6716 TECHNICAL DATA - max planing width 510mm - maximum planing height on both sides 190mm - maximum four-sided planing height 130mm from down: - guide rails - preliminary table, adjustable - smooth skid roller - 510mm planing shaft, 4-knife 5.5kW - 2 smooth, sliding shafts - adjustable rollers in the lower table top in advance: - pulling shaft, toothed - pressure - pulling shaft, toothed 2 pcs - pressure - 520mm planing shaft, 4-knife approximately 7.5kW - pressure - pulling shaft, smooth - pressure in the back: - side spindles 2 pieces - 1.right, vertical 130mm 4kW - 2nd left vertical 130mm 4kW - manual spindle feed - diameter of the spindles 40mm - adjustable spindles up / down, right / left - the axes are positioned alternately - side clamp 2 pcs - locking spindles - 2 types of feed speed + smooth about 3kW - diameter of the extraction conn ...

– Italian production – year of manufacture 2007 TECHNICAL PARAMETERS: planing width 230 mm planing height 120 mm 1) horizontal bottom 230 mm 5.5 kW 2) vertical right 130 mm 3) vertical left 130 mm (2 and 3 spindle) 11 kW 4) horizontal top 230 mm 7.5 kW all spindles up/down, right/left spindle diameter 40 mm from above 3 insertion rollers pulling metal, swivel including 2 double pulling lead shaft from above, double rubber on the side, pressure 1 pc. in the lower table top a rubber pulling roller feed on cardan rollers pneumatic clamps infinitely variable feed speed 5-22 m/min feed motor 1,1 kW electrical setting of planing thickness lifting engine 0,37 kW introductory table length 2470 mm enclosed in the cabin central lubrication of the table top extraction pipe diameters 150 and 180 mm dimensions (L/W/H) 3650 / 1200 / 1600 mm wei ...

– German production – year of production 1995 – right and left spindles with a front milling cutter ensuring parallelism and a right angle of 90° – measurement of the width of the element – electronic width setting TECHNICAL PARAMETERS: planing width 230 mm planing height 120 mm control of the width of planing electronic 1 bottom spindle 4 kW 2 right spindle 4 kW 3 left spindle 4.2 kW (front milling) 4 right spindle 4.2 kW (front milling) 5 top spindle 7.5 kW element width measurement electric height adjustment of feed rollers electric height adjustment of the upper spindle spindle diameter 40 mm six steel top rollers one top rubber roller one roller in the working table top pulling pneumatic pressure feed on cardan shafts pre-table length 2470 mm connection diameter 140 mm dimensions of the machine (L/W/H) 456 / 240 / 220 ...

– German production – corrugated top – year of production 1996 – rollers in the countertop pulling TECHNICAL PARAMETERS: planing width 230 mm planing height 160 mm corrugated top spindle diameter 40 mm 1 bottom spindle 7.5 kW 2 right spindle 7.5 kW 3 left spindle 7.5 kW 4 upper spindle 11 kW 5 bottom spindle 7.5 kW smoothly adjustable feed 6-36 m/min feed motor power 5.5 kW six upper steel pulling rollers two top rubber pulling rollers three rollers in the countertop pulling pneumatic feed pressure pneumatic shoe pressure spindles with brakes length of the pre-worktop 1970 mm electric height adjustment central lubrication (split) connection diameter 140 mm dimensions of the machine (L/W/H) 410 / 200 / 180 cm weight ~ 3000 kg

–DTR – German production – electric adjustment of the left head – adjustable spindles TECHNICAL PARAMETERS: planing width 220 mm planing height 120 mm spindle diameter 40 mm 1) bottom head 4 kW 2) right head 3) left head 5.5 kW 4) top head 4 kW 5) universal head 360° 4 kW feed motor 2.2 kW feed speed 5 – 20 m/min four steel pulling rollers two top rollers pulling rubber one pulling roller in the countertop feed on cardan shafts electric height adjustment length of the pre-worktop 1970 mm central lubrication pneumatic clamps dimensions of the machine (L/W/H) 380 / 200 / 170 cm weight ~ 2000 kg

– German production – year of manufacture 1990 – for wet wood TECHNICAL PARAMETERS: planing width max. 310 mm planing height on both sides 300 mm planing height four-sided 100 mm spindle diameter 30 mm shaft motor power 2 x 11 kW spindle motor power 2 x 7.5 kW feed speed 14-86 m/min feed speed adjustable on the variator four upper pulling shafts two lower pulling shafts four rollers in the auxiliary countertop brake minimum element length 600 mm machine dimensions (L/W/H) 290 / 170 / 210 cm weight ~ 3500 kg