dl used for sale

1 unbr. Homogenizer type HG 125 Homogenizer in horizontal design with direct drive by three-phase motor with height-level base frame. Standard version suitable for maximum system pressure up to 10 bar and product temperature up to max. 150°C. Technical data: Drive power: 18.5 KW three-phase motor Operating voltage: 400 V, 50 Hz, 3 phases Protection: IP 55 Speed: 3000 rpm Material of the product-contacting parts: 316 L (1.4404/1.4435) Shaft sealing: single-acting GLRD Side seals: Viton Connections: Suction side DN 80 DIN 11851 Printing page DN 65 DIN 11851 Throughput and Conveying pressure at water similar products: approx. 25 m3/h or 3 bar with star-triangle circuit in plastic housing without pre-locking with cable and plug

1 unbr. Homogenizer type HG 125 Homogenizer in horizontal design with direct drive by three-phase motor with height-level base frame. Standard version suitable for maximum system pressure up to 10 bar and product temperature up to max. 150°C. Technical data: Drive power: 18.5 KW three-phase motor Operating voltage: 400 V, 50 Hz, 3 phases Protection: IP 55 Speed: 3000 rpm Material of the product-contacting parts: 316 L (1.4404/1.4435) Shaft sealing: single-acting GLRD Side seals: Viton Connections: Suction side DN 80 DIN 11851 Printing page DN 65 DIN 11851 Throughput and Conveying pressure at water similar products: approx. 25 m3/h or 3 bar with star-triangle circuit in plastic housing without pre-locking with cable and plug

AUTO STAMPING MACHINE UNFOLD BOX FEEDER SYSTEM AUTO STAMPING MACHINE WITH UPGRADE VERSION 2.0 SPECIFICATION : Model : B'Smart 1000 - 2.0 Paper : CARTON & INNER Carton Min. Sise : 371 x 350 x 6.6 (mm) Carton Max. Size : 902 x 890 x 11.3 (mm) Inner Min. Size : 310 x 120 x 10 (mm) Inner Max. Size : 430 x 180 x 10 (mm) Structure Dimention : 2870 x 1045 x 850 (mm) Structure Material : Mild Steel Powder Coat Machine color : Blue Conveyor Speed : 40Meter / Min ( Adjustable ) Feeding Direction : Horizontal Power : 1 Phase

DLyte GPAINNOVA - 1D +HF - (05-2022) The DLyte 1D +HF from GPAINNOVA is an automated dry electropolishing machine, designed specifically for small volumes in dental laboratories Good working condition Please inspect. The sale includes only what appears in the photos. The buyer, by purchasing the equipment, agrees that the device must be used according to the standards and legislation in force in his country. The seller will not be held responsible in any way for misuse that does not comply with the safety conditions and the standards and legislation in force. Lots may be added to the list later. An exhibition beforehand is set up, please inspect. The equipment is made available on pallet or pallet box or cardboard with all the appropriate protections, the price of the packing is integrated into the sale price. For shipping, you can have your transport pass or go through the carrier ...

Pressure Monitor KROM SCHRÖDER DL5K pmax 300 mbar 0.5 to 5 mbar Dimensions: 95 x 90 x 50 mm

Specifications Manufacturer Siemens Model SGT-600DLE Year 2025 ( Complete overhaul ) Condition new Wattage 24,5 MW Hours 0 Frequency 50 Hz/ 60Hz Fuel Type Natural Gas Voltage 11000 KV Quantity N.1 Located EUROPE General Information - The turbine operates at 50Hz or 60hz . Timeframe for an additional power supply. - The turbine operates on natural gas - New core engine, 0 hours engine - Core engine is under warranty by Siemens - Low emissions and long maintenance intervals - Suitable for power generation and mechanical drives 2. Device specifications 1. Power output: 24,5 MW(e) 2. Fuel: Natural Gas. 3. Frequency: Dual 50/60Hz 4. Gross efficiency: 35.00% 5. Heat rate: 10,294 kJ/kWh (9,756 Btu/kWh) 6. Turbine speed: 9,500 rpm 7. Print ratio: 16.9:1 8. Exhaust mass flow: 40.0 kg/s (88.2 lb/s) 9. Exhaust gas temperature: 555°C (1,031° ...

Thermo Haake DL30 Recirculation Thermostat; ; Ambient temperature: +5 °C to 200 °C; Type: 003-2890 DL 30; Heating power: 2.0 kW; ; In excellent condition; ; Internal reference: FA-2493; Auction-ID: A1-50994-1164

This compact mini excavator has been developed for work in places where larger machines simply cannot reach. With a width of only approx. 69 cm, the machine is ideal for passageways, garden gates, narrow paths, renovation projects and other locations with limited working space. The DLM650 is powered by a 6.8 kW Loncin G300 petrol engine and runs on sturdy rubber tracks. The operation is clearly done via double joysticks. Thanks to the swiveling stick (side swing), it is also easy to work close to walls, fences and other obstacles. A dozer/stabilizer blade is located at the front, which can be used for both grading soil and for additional stability during excavation. The machine is supplied with an excavator bucket of approximately 25 cm wide and has hydraulic connections for the use of suitable attachments. With a dead weight of approximately 650 kg, this mini excavator remains easy to t ...

Unused in the original packaging The UF Equipment DL400 Concrete Saw is a powerful and reliable ring saw, specially designed for cutting through concrete, asphalt, and other hard building materials. This professional concrete saw combines power, precision, and user-friendliness, making it the ideal choice for construction companies, contractors, and industrial use where heavy-duty cutting jobs are required. Extra protective caps and safety equipment. Transport wheels for easy movement around the workplace. Auction-ID: A1-40407-104

This compact mini excavator has been developed for work in places where larger machines simply cannot reach. With a width of only approx. 69 cm, the machine is ideal for passageways, garden gates, narrow paths, renovation projects and other locations with limited working space. The DLM650 is powered by a 6.8 kW Loncin G300 petrol engine and runs on sturdy rubber tracks. The operation is clearly done via double joysticks. Thanks to the swiveling stick (side swing), it is also easy to work close to walls, fences and other obstacles. A dozer/stabilizer blade is located at the front, which can be used for both grading soil and for additional stability during excavation. The machine is supplied with an excavator bucket of approximately 25 cm wide and has hydraulic connections for the use of suitable attachments. With a dead weight of approximately 650 kg, this mini excavator remains easy to t ...

DLyte GPAINNOVA - DLyte10D - (10-2022) Good working condition Please inspect. The sale includes only what appears in the photos. The buyer, by purchasing the equipment, agrees that the device must be used according to the standards and legislation in force in his country. The seller will not be held responsible in any way for misuse that does not comply with the safety conditions and the standards and legislation in force. Lots may be added to the list later. An exhibition beforehand is set up, please inspect. The equipment is made available on pallet or pallet box or cardboard with all the appropriate protections, the price of the packing is integrated into the sale price. For shipping, you can have your transport pass or go through the carrier JMA express, or ask us for a shipping quote by Fedex. See General Terms and Conditions of Sale Auction-ID: A1-51471-43

Doosan DL420-3 wheel loader. Scania DC13 6-cylinder diesel engine. Motor power: 264 kW. Weight indicated on the machine plate: 24,000 kg. Hours shown on the meter: approximately 11,861 h. Equipped with a closed cab and front loading bucket. Reference tires for this model: 26.5 R25. Reference dimensions: approximately 8,910 x 3,270 x 3,535 mm (L x W x H), depending on the configuration. Used machine with visible signs of use, dirt, wear, scratches, paint damage and corrosion typical of its use. The bucket has wear, corrosion and remains of adhered material. The cab windshield has visible damage/breakage. The seat and interior elements show signs of wear and tear. Consult the photographs to check the general visual condition of the machine, bucket, tires, cab and other components. Auction-ID: A1-51537-4

DOOSAN DL420 wheel loader. Motor power according to the manufacturer's plate: 264 kW. Maximum weight indicated on the plate: 24,000 kg. 6-cylinder diesel engine. Hours indicated on the meter: approximately 17,061.2 h. Equipped with an enclosed cab and front bucket. Reference bucket capacity: approximately 4.0 m³, depending on configuration. Reference tires: 26.5-25-20PR. Reference dimensions: approximately 8,880 x 3,270 x 3,522 mm (L x W x H), depending on the configuration. Used machine with visible signs of use, wear, dirt, scratches, paint damage, and corrosion consistent with its previous use. The bucket has visible wear and corrosion. The front windshield of the cab has a visible break/crack. Wear is seen on the tires and on different elements of the machine. Refer to the photographs to check the general visual condition of the machine, bucket, tires, cab and operator' ...

Specifications LC 300A LC 340A Max. turning diameter above the bed 300 mm 340 mm Max. workpiece length 500 / 750 / 1000 mm 500 / 750 / 1000 mm Max. turning diameter above carriage 170 mm 210 mm Max. turning diameter above broken bed 430 mm 470 mm Effective width of the broken bed for circular table 137 mm 137 mm Spindle Bore Diameter 38mm 38mm Spindle bore taper (Morse) 5 5 Spindle nose, code no. C5, D5 , C5, D5 Distance from Tool Mounting Socket to Spindle Shaft 18 mm 18 mm Tool Area Size 16 x 16 mm 16 x 16 mm Tailstock (Morse) Cannon Cone3 3 Spindle Speed Range 60 - 2000 RPM 60 - 2000 RPM Number of spindle speed ranges 9 9 Longitudinal feed range 0.03 - 0.43 mm/rpm 0.03 - 0.43 mm/rpm Cross feed range 0.015 - 0.21 mm 0.015 - 0.21 mm Metric threads 0.25 - 9 mm 0.25 - 9 mm Threads per inch 72 - 4 3/4 threads/inch 72 - 4 3/4 threads/inch Threads wi ...

Equipped with 2 ramps (3050x400 mm.) Auction-ID: A1-47424-102

Auction-ID: A1-51062-318

Industrial compact hygiene airlock for controlled access to hygienically sensitive production areas. The stainless steel system combines automatic continuous sole cleaning with hand hygiene and disinfection as well as mechanically controlled access control. It is particularly suitable for food, pharmaceutical, cosmetics and comparable production companies with increased hygiene requirements. Technical data / equipment: - Stainless steel hygiene lock - Continuous sole cleaning with rotating cleaning brushes - Version 1100, brush range approx. 700 mm - Input control unit EK 400 - Integrated hand hygiene and disinfection unit - Two-hand control range - Automatic release of the passage after the hygiene process - Stainless steel turnstile as access barrier - Lateral personnel guidance made of stainless steel tube - Integrated control and switching technology - Dosing lines for  ...

Unused in the original packaging Saw blade diameter: 400 mm Auction-ID: A1-40407-42

4WD, LED work light, towing eye with pin 60mm, automatic grease lubrication, 4 driving speeds, heating, air conditioning, reversing camera, seat heating, radio Auction-ID: A1-47396-1603

Power failure Kubota engine Auction-ID: A1-47396-1108

16000246, approx. 2900 operating hours Auction-ID: A7-51504-114

460mm; including charger and 2x 5Ah 18V lithium battery; Auction-ID: A1-51257-442

82MW ISO rated combined cycle power plant. The plant’s main equipment is composed of a Rolls Royce Trent 60 DLE Gas Turbine (also known as the SGT-A65), a Nooter/Eriksen HRSG, and a Siemens SST-300 Steam Turbine. These are below; 1. Rolls Royce USA, manufactured Trent 60 (SGT-A65) Gas Turbine Generator Set; · Manufactured in 2016, delivered in August 2017. Never used. · 65.9 MW(e) ISO · 43.8% Gross efficiency / 8,228 kJ/kWh Heat Rate · DLE Dry Low Emissions with ≤ 25 ppmvd at 15% O2 on fuel gas · Cold start to full power in under 10minutes · 50Hz, but easily convertible to 60Hz · Engine still preserved in original shipping container · An aero derivative gas turbine 2. HRSG is licensed by Nooter Eriksen USA; 3. Siemens Steam Turbine Generator SST-300 C2S/C160; · Manufactured in 2016 · Output 15.75MW ISO · Speed 7059 RPM · Admi ...

Surface grinding machine manufactured in 2006. This STAEHLI DLM 450 features a lapping wheel diameter of 450 mm and a maximum lapping wheel speed of 110 rpm. It has a robust machine weight of 2100 kg and dimensions of 1200 × 1650 × 2050 mm. If you are looking to get high-quality lapping capabilities, consider the STAEHLI DLM 450 machine we have for sale. Contact us for further details regarding this machine.

This Priess & Horstmann BMA-DLS-CNC was manufactured in 2000. Ideal for woodworking applications, it offers reliable performance for a variety of tasks. Consider the opportunity to buy this Priess & Horstmann BMA-DLS-CNC woodworking machine. Contact us for more information.

Mäder DLP 1700 HV Direct Acting Air Press Press Direct-acting air presses are used wherever the compressive force is required constantly over a longer distance or where a large immersion depth is required: e.g. when pressing pins, bushings and ball bearings or when forming. DLP 1700 HV Direct-acting compressed air press Compressive force at 6 bar: 17 kN Working Stroke: H mm: 40/60/80 More items - new and used - can be found in our shop! International shipping costs on request!

NERI DL400 type V duplex vignette labeller, for top labelling of cartons or similar. Fitted with two labelling heads, carton size range from 80 x 30mm (W x L)) to 180 x 120mm (W x L). Output up to 100 cartons per minute. All stainless steel construction.

Double door depyrogenation owen De Lama model DLST/L year of manufacturing 1998. Useful capacity 5440 liters. Supply voltage 380 V - 50 Hz Tri - phase. Installed power 157 kW. Maximum working temperature 250 C °.

DEPA Compressed Air Diaphragm Pump Manufacturer: Alfa-Laval Type: DL40-UL-T-T Item #: 09855 Year of construction: 1999 LBH: 350 x 460 x 700 mm

I sell here several machines, equipment, forklifts, work platforms, spare parts for forklifts and work platforms and spare parts and accessories for woodworking, so be sure to pay attention to my other auctions Trailer work platform Trailer work platform Telescopic lift lift DENKA Type: DL21 Year of construction: 2000 Payload 200 kg Platform dimensions approx. 1.0 x 0.7 m Transport dimensions approx. 8.2 x 2.46 x 1.8 m Weight approx. 2500 Kg Working height approx. 21.3 m Platform height approx. 19.3 m Range approx. 9 m (center basket/ 80Kg) hydraulic shunting drive (mobile from the basket) automatic cable reel Support can be operated from the basket TÜV: 08/2024 UVV: 08/2023 Extensive overhaul work was carried out on the stage: - Paint renewed. - Hoses renewed. - new batteries - all oils changed. - new test book issued ...

Lathe and various small parts Manufacturer: Eugene of white Type: DLNE Year of construction: 1954 Top width: 2000 mm Bed width: 380 mm Bed length: 3410 mm Outer dimensions: 3,850 x 1,020 x 1.135 mm Net weight: approx. 2500 kg maximum speed: 935 RPM maximum speed faceplate: 710 RPM Tour is possible upon request.

Double door autoclave De Lama model DLOV year of manufacturing 1998. Useful capacity 4990 liters. Supply voltage 380 V - 50 Hz Tri - phase. Installed power 6 kW. Maximum working pressure 2.5 bar. Maximum working temperature 138.2 C °. Installed cycles: A sterilization + drying B for vials C For closed containers I test cold vacuum machine J sterilization air filter in situ

Parallel Lathe WMW NILES type DLZ 500 IV L 1000 Between points: 1000 mm Maxi Ø on bench: 500 mm Maxi Ø over saddle: 300 mm Spindle diameter: Ø 50 mm Spindle speed: from 28 to 1400 RPM 3-jaws chuck Ø 200 mm Threadings: Metric + Whitworth Tailstock CM4 Auto Feeds transverse + longitudinal + rapid Lubricant pump Voltage: 380 V Dimensions (L x W x H): 3000 x 1400 x 1500 mm Weight: approx 2,5 T

Dry Transformer Manufacturer: Schneider Type: DLPS 63E The device is NEW and fully functional. see pictures for more details.

Dry Transformer Manufacturer: Schneider Type: DLPS10F - 0617T07001 The device is NEW and fully functional. see pictures for more details.

Transformer Dry Transformer Manufacturer : Schneider Type: DLPS10F - 0617T07001 The product is NEW and fully functional. see pictures for more details.

Diaphragm pump, compressed air diaphragm pump, chemical pump, compressed air-operated double diaphragm pump -Manufacturer: Alfa Laval, air-operated double diaphragm pump -Type: DL25-AA-EET-Q -Flow rate: l/min -Discharge pressure: bar -Total dimensions: 240/230/H300 mm -Weight: 8.7 kg

Key data: 11 , 1 , 250

Claw compressor Gardner Denver ( Elmo Rietschle ) C-DLR-250, UNUSED. Capacity 250 m3 / hour; 11 kW; EX motor; maximum pressure 1,8 bar; 2950 round per minute; Dimensions L 1450mm, H 1100mm, W 950mm Electric connection 400 V

Diaphragm pump, compressed air diaphragm pump, chemical pump, compressed air-operated double diaphragm pump -Manufacturer: Depa, air-operated double diaphragm pump -Type: DL25-FA EEE P -Flow rate: l/min -Discharge pressure: bar -Dimensions total: 340/240/H325 mm -Weight: 9.6 kg

Forklift battery charger, industrial charger, Forklift battery charger, industrial charger, Si rectifier -Manufacturer: Jungheinrich, charger type DLW 12/20 SN -Input voltage: 220 V 50 Hz -Power: 12 V/20 A -Dimensions: 410/200/H340 mm -Weight: 12 kg

gear motor, electric motor, electric gear motor -Manufacturer: ABM Baumüller, gear motor type IIb / DLB 421 -Speed: 50 rpm -Power: 0.8 kW -Design: B3 -Shaft: Ø 35 x 80 mm -Dimensions: 475/240/H235 mm -Weight: 38 kg

Centrax 501 KB57 DLE Gas Turbine-Generator Package engine overhaul in 2017 at 24 000 hours 372 start service hours 23 000

Key data: 630 mm, 2000 mm, 400 mm

Sell a well-preserved lathe from WMW model DLZ 630 x 2000. The machine is in good condition. The dimensions of the machine are LxWxH 4200mm x 1600mm x 1400mm. Spindle passage is 62mm. The machine was completely cleaned. Incl. guideline and sitting skirt. If you have any further questions, please contact us. The machine can be inspected and tested under power by prior appointment. On-site loading is no problem and free of charge. Furthermore, the machine can be delivered in the immediate vicinity and against assumption of costs, with its own truck. A suitable unloading facility must be available for this purpose. The sale is without guarantee and warranty. All information without guarantee.

8x ProMinent dosing pumps DLTA1020PVT2000UA1030DE0

VEB DLZ 1000/4000

Required air-pressure: 6 bar 0: 6 m coolant capacity: 7 m3/h Air Operated Diaphragm Pump Type(s) DL25 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Required air-pressure: 7 bar weight: 3 kg dimensions of the machine ca.: 212 x 265 X 200 mm BxHxT Air Operated Diaphragm Pump Type(s) DL15-PM-TTT Technical data: - Connection size medium - 1/2 BSPT female thread - Material housing - PP polypropylene - Center section - PP polypropylene - Diaphragm material - PTFE - O-ring material - PTFE - Check valve material - PTFE - Max. flow rate - 2.2 m³/h - Max. medium pressure - 7 bar - Compressed air supply - up to 7 bar - Solid size max. - 2.5 mm - Dry suction max. - 2.5 m - Dimensions WxHXT - 212 x 265 X 200 mm - Net weight - 3.5 kg PTFE diaphragm for the highest chemical requirements, very good resistance to aggressive media and chemicals, temperature range: -5 °C - +130 °C. PP polypropylene housing is highly resistant to acids, many water-soluble, inorganic acids and bases. Also available as electrically conductive housing material. Tempera ...

Transformer, transformer, converter, three-phase autotransformer, three-phase transformer, three-phase transformer, single-phase transformer, three-phase isolation transformer -Manufacturer: J Schneider, transformer type DLES 1.78-881129T4 -Power: 1540 VA -Technical data: see photo nameplate -Dimensions: 200/130/H230 mm -Weight: 14.3 kg.

Linear drive, linear gear, lifting gear, spindle drive, linear axis, linear rail, linear guide, roller guide rail, guide carriage, guide rail, rail guide -Linear drive: stroke length 620 mm from Achterberg Toolbase AK -Actuator: DLG 060-068.01 -Threaded rod: Ø 12 x 615 mm -Number: 8x linear drive available -Price: per piece -Dimensions: 745/80/H80 mm -Weight: 1,7 kg/piece

Heavy-duty lathe, lathe, lead screw lathe, lead screw lathe -Condition of machine bed: very good -Machine bed: hardened -Manufacturer: Martin, lead screw and feed screw lathe type DLZ 502 -Turning length: 2200 mm -Turning diameter over bed: 580 mm -Turning diameter over support: 300 mm -Spindle bore: Ø 65 mm -Spindle speeds: 22.4 - 1000 rpm -Wedge bar chuck: Forkardt Ø 320 mm -Tailstock mount: MK5 -Drive: 7.5 kW -Accessories: 4x bezels, tool holder, tools (see photos) -Dimensions: 1260/3720/H1260 mm -Weight: 2510 kg