digital printing presses used for sale

Used AMOS AEP 20 juice belt press, with a grinding system and a pallet generator. Belt with a capacity of 1 meter per hour, i.e. about 3 tons.

Used belt press made by Monobelt, type NP12CK. New 2009. Weight 1620kg. Belt width - 1200 mm. Working flow - up to 10 m3 / h. Throughput max - 170-360 kg DM / h. Installed power: Press with 0.55 kW thickener 2.2 kW flushing pump Rinse water quantity 5 m3 / h Net weight / maximum usable weight 1620/2800 kg Sludge inlet connection DN80 1 ”GF rinse water inlet Filtrate outlet connection DN150 Manufacturer's documentation.

Used press for pre-pressing cheese. Technical data: - producer TEWES BIS Barczewo - year of production 2006 - dimensions: overall length 4780 mm, width 1560 mm, height 3850 mm - pressing area 4.33 m3 - internal dimensions of the bath: length 3700 mm, width 1170 mm, depth 730 mm - mass of pressed cheese approx. 1000 kg - thickness of the cheese layer after pressing approx. 250 mm

We sell a used and revised TTW with a deposit of 30-100g.

Passage width 2500 mm Stroke 900 mm Total power requirement 62 kW Machine weight ca. 27,5 t Dimensions L x W x H approx. 3950 x 2200 x 4850 mm Retraction force 40 t Master cylinder 2 pieces Column diameter 220 mm Installation height 1300 mm Table size 2500 x 1600 mm Ram size 3100 x 16000 mm Table height above floor approx. 900 mm Flow speed 200 mm/sec Return speed 200 mm/sec Working speed 5 - 15 mm/sec Oil tank 1500 l Oil quantity 1200 l Pressure control adjustable from up to 50 - 400 t Thermoforming cushion 1400 x 800 mm Deep-drawing unit capacity 30 - 60 t Deep-drawing cushion stroke 250 mm Deep-drawing cushion speed 5 - 80 mm/sec robust machine body with solid welded construction low-maintenance and reliable Piston rod with induction hardening and chrome cladding T-slots according to customer requirements, if not specified 22mm according to DIN CE Certific ...

-) 2-jaw drill chuck 20 mm -) Dowel drilling device with 4-compartment grid 16-32-22-25 mm -) 90° frame stop pluggable -) Miter stop 45° and 22.5° pluggable -) Moving equipment -) Workpiece clamp manual 2 pieces -) Suction connection D 100 mm Optional accessory: -) Gauge in handwheel -) infinitely variable double angle miter stop -) 1 lever operation -) switchable pneumatic stroke for two planes -) Leaser on request

Specifications: - working length 3500 mm - Stand passage 3050 mm - max pressing force 2000 kN - Distance table / ram max. 480 mm - Stand projection 260 mm - Ram stroke approx. 300 mm - Lifting speeds - Downspeed idle max. 100 mm/sec - Boost speed 80 mm/sec - Downward pressing speed max. 10 mm/sec - Total drive power 25 kW - Space requirement approx. W 4500 x H 3150 x D 2100 mm - Weight approx. 16000 kg -with: - CNC control CYBELEC renewed in 2008 - controlled crowning device - controlled backgauge with height adjustment 5 - 1000 mm - hydr. Tool clamping - Upper tool + universal die tool - Material requirements - Two-hand control panel

Bürkle Multifoiler Model BTF 1628/60 Year 1997 Plant for coating smooth and formed MDV parts with thermoplastic films, of roll or as a cut, for film PVC,PP,high gloss PVC,ABS. Suitable for thermoforming or membrane process. Max part size 1250x 2550 mm/ Divide thickness 6-35 mm Hot plate dimensions 1600 x 2800 mm max heating temperature 140° Stroke 230 mm Control Siemens Total connection 38 Kw Weight 16,5 t

Stock number: 3754 HYDRAULIC PRESS Manufacturer: STENHOJ, Type: 25T TE Machine NO.: 54718, Year of construction: 1988 Specifications: Table size 620 x 380 mm Stroke length 300 mm pressing force 25 ton Weight: 1600 kg

Hydraulic press

Single-column press with 15 T power suitable for continuous shift operation (a) travel speed 10 mm downwards; b) Opening speed up to 25 mm/sec c) Starting pressing speed 10 mm/sec d) Table size 400x400 mm e) Ram size 200x200 mm, with T slots and central cylinder tension f) Total size approx. 1150x800x1750 mm g) Oil temperature display on the oil tank h) Pressure adjustment from 5 T to 17 T (adjustable via rotary control) i) Two-speed hand lever operation j) Machine body powder-coated, or double painted k) Control cabinet supply cable from above with 3000 mm cable and 16 ampere plug l) Installation, commissioning, instruction against separate charge Press type single-column press Thermally neutral 80 – 120 °C Number of operating pages 1 page Forces Pressing force max. ( at 250 bar ) 150 kN Free tear-off force max. 10 kN Pressure build-up time Closed tool Stee ...

Fortuna dough dividing and warp knitting machine Type: A4 Roll Press Division of 30 Weight range dough pieces 32-120 grams Dough insert per ratchet 960-3600 grams Year of construction: 2015 electric head including 3 knitting plates The robust design and duration of the oil cracking of the transmission parts ensures a long service life Easy cleaning even of the cutter head 380V / 50Hz Weight of the machine approx. 540 kg Trade-in and delivery on request Option for a complete overhaul of the machine Dimensions:  Height: 150 cm Width: 70 cm Depth: 70 cm

immediately available CNC press brake YAWEI PBH160/3100-4C - Pressing force: 1600KN - bending length: 3100mm - Year of construction 2022 - CNC controlled hydraulic crowning - Cybelec Modeva 19T control - WILA upper tool clamping - 60mm table with 13.5mm x 22mm groove for insertion matrices - 2 front support arms movable on linear guide - CE with Fiessler AKAS IIF (automatic height adjustment) - 24 months warranty - Commissioning, training

Veneering press OMC PL 105 LC 30/13 Water Work surface 3000x1300mm Opening width 400mm 6 cylinders with a diameter of 85mm Total pressure 105T Maximum heating temperature 85 degrees Control system logic contorl Machine control from touch panel readings Temperature, pressure force, shelf opening time, loading area calculator, programming of gluing processes Power 21KW CE Certificate Production 2023 Machine available on request New machine Net price

Working width: 4500 mm Working height: 3000 mm Number of cylinders: 6 St. Dimensions (L/W/H): 5500x1400x3550 mm Weight: 3000 kg S&S frame press Bavaria 2000 L, built 2026 --------------------------------- SHORT TIMED availabe exw warehouse Engelfried, 73447 Oberkochen NEW for the Holz-Handwerk 2026 trade fair in Nuremberg: Now also with semi-automatic positioning of the vertical press cylinders 1, 2, and 3 via enabling switch, including ON/OFF selector switch for beam 2 With automatic pressing cycle + manual control for corner connections tenon+slots and dowel connection/mortised tenon, can be switched using a selector switch on the control cabinet. With basic equipment for optional use of counter profiles if the sash is rebated on the loose part. CE version Basic machine in the strongest frame welded construction, with thick-walled special hollow profiles. Guideways of the pressure beam ...

FRITZ MÜLLER ZE 625-4 hydraulic press was built in Germany by Fritz Müller GmbH & Co. KG. The machine has been continuously maintained and upgraded throughout its service life. The first major overhaul was carried out in 1988 by the manufacturer’s service Machinenfabrik Mueller-Weingarten AG. A second overhaul was carried out in 2020, during which the press was brought up to current safety requirements. As part of this overhaul, a new control system based on a SIEMENS SIMATIC S7 PLC controller and a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel was installed, the entire electrical system was replaced, seals were replaced and light curtains were installed. The FRITZ MULLER ZE 625-4 is an extremely versatile press designed for even the most demanding metal forming operations. It is capable of performing operations such as deep drawing, stamping, forging, straightening large w ...

SPECIFICATIONS: Hydraulic press for bent elements Dimensions of the work table mm: 3000 x 1600 Number of pistons: 2 diameters Ø 200 mm Piston stroke mm: 1400 -Fence -Oil pump - 02 Steam outlet openings

Manesty D3B tablet press Serial: 24D117 Manesty 16 station tablet press, up to 500 tablets per min, max tablet diameter 25mm, max depth to fill 20mm, 3Ph

ARISA S-2-630-240-120-LD mechanical press was built in 2005 in Spain by Arisa S.A. (now Nidec Press & Automation Co. (NP&A)). The machine on offer is an excellent choice for series production of components used in the broadly defined automotive or machinery industry. It enables even the most demanding metal forming operations, such as precise punching and stamping of metal parts. In addition to its standard purpose, depending on the tooling and material feed systems used, the machine can also be used as a transfer press or progressive press. All machining processes are performed with a high press force of 630 tonnes. The drive system, in the form of a flywheel and an eccentric gear, cooperating with two connecting rods, ensures even torque transmission and smooth control of the slider movement. The slider, on the other hand, is guided at eight points using roller guides, which increas ...

NIDEC ARISA S-2-500-240-120-FD mechanical press was built in 2006 in Spain by Nidec Press & Automation Co. (NP&A). It is an extremely versatile press that is used in the series production of components for the broadly defined automotive or machinery industry. It enables even the most demanding metal forming operations, i.e. precise punching and stamping of metal parts. In addition to its standard purpose, with the appropriate tooling and material feeding systems, the machine can also be used as a transfer press or progressive press. All processes are performed with a high press force of 500 tonnes. The drive system of the NIDEC ARISA S-2-500-240-120-FD press is based on a flywheel and an eccentric gear, cooperating with two connecting rods. This solution guarantees even torque transmission and a smooth working cycle. The slider, on the other hand, is guided in multiple points by rolle ...

Horizontal Baller for SALE/RENT BAUER 300 Baller is in good working condition (was used in printing house)! Technical specifications: Installation of the secondary raw material baler Manufacturer: BAUER Model: 300 Year of production: 1994 Power: 22 kW Kledex Dk S Asm Aty Atjl Pressing force: 40-50 t The dimensions of the baler are 10,300 x 2,000 x 3,000 mm Tipping weight: ~ 400 kg PRICE AVAILABLE UPON REQUEST! ----- Verkaufen/Mieten Ballenpress BAUER 300 Technische Daten: Bsbmeycfv Iecbw Nvswh Installation der Sekundärrohstoffpresse Hersteller BAUER Modell 300 Produktionsjahr 1994 Leistung 22kW Druckkraft 40-50 t Die Abmessungen der Presse betragen 10300 x 2000 x 3000 mm Kippen Gewicht ~ 400 kg PREIS BEI ANFRAGE!

Manesty D3B tablet press Manesty 16 station tablet press, up to 500 tablets per min, max tablet diameter 25mm, max depth to fill 20mm, 3Ph

Hydraulic press brake Manufacturer: MENGELE Type: A 100-2 Pressing pressure: 100t Stroke: 160mm electr. Connection: 400V 3Ph Year of construction: 1964 Condition: used and functional

LIKON 200C Horizontal Baler Machine Technical specifications: Engine power - 22 kW Year of production - 1994 With oil cooler Horizontal binding x 4 times Press force - 30 t Overall dimensions of the baler: 10000 x 2000 x 2750 mm Press weight: 10 t Loading opening dimensions: 1400 x 700 mm Bundle dimensions - 700 x 1100 x 1000-1200 mm, variable length With hydraulic oil No binding wire It worked in a printing shop without a conveyor belt, only with dry-shredded printing waste! Motorcycle hours - 62639 The baler is in good condition, ready for operation PRICE ON REQUEST! ----- Horizontal Baller Paal LIKON 200C Technische Daten: Motorleistung - 22 kW Produktionsjahr - 1994. Mit Ölkühler Horizontale Bindung x 4 Mal Presskraft - 30 t Gesamtabmessungen der Presse: 10000x2000x2750 mm Eigengewicht der ...

ZTS KOSICE LEK 160 eccentric press was built in 1984 in Czechoslovakia by Závody Tažkého Strojárstva n.p. Košice. The machine is used in cold metal forming. It is capable of performing operations such as precise punching, stamping and bending. All these machining processes are performed with a high press force of 160 tonnes, which, combined with a very dynamic slider, guarantees the best machining results. The slider makes between 32 and 50 strokes per minute and its stroke is adjustable in the range from 25 mm to 160 mm. The ZTS KOSICE LEK 160 is also distinguished by its very rigid C-shaped design, which offers excellent process stability during even the most intensive challenges. The work table with a length of 1000 mm and a width of 740 mm enables mounting of both larger workpieces and tools. All this makes the offered LEK 160 eccentric press an excellent choice for the producti ...

Compact small briquetting press CA 10-15 KG/H Diameter of the briquettes approx. 55 mm 2.6 KW POWER CONSUMPTION V 230/50 CAN BE OPERATED WITH HOUSEHOLD ELECTRICITY BUT ALSO OPERABLE WITH V400/50 AND ZERO-WIRE PLUG ADJUSTABLE PLIERS Machine for do-it-yourselfers or small craft businesses Space requirement approx. .170x50x100cm, Weight 90kg

clamping force: 350 kN injection volume: 59 cm³ screw diameter: 25 mm platen size: 400 x 400 mm Condition: used, Specification: injection moulding machine for rubber - used International size: 350-90 clamping unit: - clamping force: 350 kN - clamping platen size: 400 x 400 mm - Clear distance between tie bars: 270 x 270 mm - Mould installation height min.: 225 mm - Distance between clamping platens: max. 550 mm - Opening stroke max.: 325 mm - Ejector stroke: 125 mm Injection unit: - Screw diameter: 25 mm x 20D - Injection volume max.: 49 cm³ - Injection part weight: 59 g/hp - Max. injection pressure: 1,860 bar - Screw circumferential speed: 37 m/min - Cylinder heating: 4x 900 W - Nozzle heating: 300 W - Heating complete: 4,6 kW - Pump motor: 11 kW - Total power ...

Vacuum press, vacuum table, vacuum table from Joos with silicone membrane Universally applicable press, veneer press for veneering, coating, mold gluing, mold veneering, edge banding, etc. With this press, you can do without a hydraulic veneer press, with some restrictions. New heat-resistant silicone membrane, extremely stretchy and easy to clean. Can also be used for forming preheated thermoplastic materials such as acrylic glass or solid surface materials. Inner frame dimensions approx. 2900 x 1410mm, usable area approx. 2800 x 1300mm Working height approx. 900mm Vacuum pump Becker VT4.40, 400V, 1.5 kW with 40 m³/h capacity and two vacuum tanks each 200 liters, thus comfortable working, fast evacuation. Electronic vacuum pressure switch, which means that the pump switches off when the vacuum is reached and does not run constantly Mobile on four swivel castors, lockabl ...

Pressing force 1000 kN Table size 750 x 560 mm, diarrhoea opening 100 mm Installation height 800 mm, stroke 500 mm Projection 360 mm Bear size 530x400 mm, 2 T-slots Ram speed: down 200 mm/sec, up 400 mm/sec Connection load approx. 21 kW Incl. Feeder WE16 for 160 mm bandwidth Coil tray and straightening unit Fabr. OFFICE; Type CA200/R40-7, YOC 1994 Reel, loop control Two-hand operation Manuals

Key data: 300 t

DURENDUS 300 T Workshop Press – Single Column Press – 1,600 mm Clear Width, 550 mm Stroke The machine shown here has already been built and delivered on behalf of a customer. We can manufacture this machine for you at very short notice – gladly taking individual options into account. It is a hydraulic workshop press for press-fitting, straightening and assembly work in the workshop and industrial sector. Base price: 22.450 € net Options (on request): The options listed are based on completed customer projects and enable the machine to be specifically adapted to the respective application. The basic machine represents a functional basic design – in practice, in most cases it is expanded with additional equipment and configured accordingly for the specific project. Table top with X-shaped T-slot 800 × 1,200 × 120 mm Pressure adjustment Lateral displacement  ...

Key data: 400 t

DURENDUS 400 T Workshop Press – Single Column Press – 1,600 mm Clear Width, 550 mm Stroke The machine shown here has already been built and delivered on behalf of a customer. We can manufacture this machine for you at very short notice – gladly taking individual options into account. It is a hydraulic workshop press for press-fitting, straightening and assembly work in the workshop and industrial sector. Base price: 35.950 € net Options (on request): The options listed are based on completed customer projects and enable the machine to be specifically adapted to the respective application. The basic machine represents a functional basic design – in practice, in most cases it is expanded with additional equipment and configured accordingly for the specific project. Table top with X-shaped T-slot 800 × 1,200 × 120 mm Pressure adjustment Lateral displacement of ...

Standard Equipment's Chrome Coated Cylinder Boiled Steel Body Pressure indicator Pressure Adjustment User guide 2 Years Warranty CE

Key data: 500 t

DURENDUS 500 T Workshop Press – Single Column Press – 1,600 mm Clear Width, 550 mm Stroke The machine shown here has already been built and delivered on behalf of a customer. We can manufacture this machine for you at very short notice – gladly taking individual options into account. It is a hydraulic workshop press for press-fitting, straightening and assembly work in the workshop and industrial sector. Base price: 46.950 € net Options (on request): The options listed are based on completed customer projects and enable the machine to be specifically adapted to the respective application. The basic machine represents a functional basic design – in practice, in most cases it is expanded with additional equipment and configured accordingly for the specific project. Table top with X-shaped T-slot 800 × 1,200 × 120 mm Pressure adjustment Lateral displacement of ...

pressure: 100 t table length: 2000 mm table width: 1580 mm stroke: mm pressing speed: mm/sec voltage: 400 V return capacity: t max. table loading capacity: 10.000 / 20.000 kg total power requirement: 18 kW weight of the machine ca.: 22 t dimensions of the machine ca.: 5,65 x 2,95 x 5,85 m Serial no: 03.246.00 max. Distance between columns (width) 1620 mm max.load upper table no swiveling 10t / swiveling 6t max.load lower table 22t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stock number: 3768 CNC PRESS BRAKE Manufacturer: DONEWELL, Type: 100 x 3000 Machine NO.: 588 12 2348, Year of construction: 1988 Specifications: Size bending length 3100 mm Size Printing capacity 100 tons Stroke length 215 mm Stand passage 2600 mm Projection 265 mm Bending speed 420 mm/min Hydraulic. CNC control Cybelec EURO III Fabr. Controlled in Y1-Y2-X Achen Program-controlled backgauge. X - 500 mm Accessories: Segment-split upper tool 3100 mm Multi bottom tool 3100 mm Operating manuals Length: 1300 mm, Height: 2450 mm, Width: 3100 mm, Weight: 7000 kg

HofmannLangloch drill Brand Hofmann Type LL150 Year of construction Specifications: drilling depth max. 145 mm (drill head movement) Drilling length: max. 230 mm (table movement) Vertical drilling spindell run max.135 mm Drilling: Drilling depth limitation Table: side ward movement via sep. Handle Cast iron table: solid with mechanical product clamp Height adjustment: Handwheel Motor power 1.3 kW Chuck 5 - 20 mm Condition: functionally tested

Code: 0377 Brand: COLOMBO R Model: PCA.S Automatic continuous-cycle hot-pressing line for the production of panels, furniture, doors, paneling, sandwich panels, and various Sturdy supporting structure Composition: 4-roll gluing machine OMMA- Width 1400 mm Disc transfer conveyor Preparation table Press COLOMBO 5500 x 1400 mm - n° 8 pistons - diameter 150 Solid steel platen Top-down pressing Pressure 4 kg/cm² Automatic unloading with photocell devices Work surface height 800 mm Closing times are reduced to 1–2 seconds and opening times to 2–3 seconds Overall dimensions press mm 5960 x 1900 x 2320 h Complete line length 22 mt Installation of the line does not require any foundation

Diaphragm press Friz type MFP 15/27 • Cover table size (mm): 2700 x 1500

Used SMG HZPUX 350/200 - 1500/1300 moulding press in good condition! Main technical data: - Power: 510 ton - Maximum span with castle: 1460 mm - Minimum light with castle: 520 mm - Maximum span without castle: 2160 mm - Minimum light without castle: 1220 mm

Vertical baler HSM V-Press 860 plus, built in 2021 Technical data: Manufacturer: HSM Type: V-Press 860 plus Year of Make: 2021 Hours: 450 Pressing force: 60 t Drive power: 4 kW Filling opening: 1195 x 645 mm Filling height: 1114 mm Bale size: approx. 1200 x 1200 x 780 mm Bale weight: 480 kg Binding: manual Theor. Idle cycle time: 25 s Theor. Pressing capacity: 12 cbm/h Dimensions: 1800 x 1253 x 2990 mm (WxDxH) Weight: 2213 kg Materials: foil, paper, cardboard boxes Note: The press is in good condition. It has been checked and tested by us. You can find a video on our website or Youtube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offers are subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. Th ...

Eccentric Press Brand Ebu Type EP15 Table size 400x430mm Max pressure 15 000kg Table height adjustment Table passage D160mm Stroke adjustment 4-70mm Ram bore 40mm Projection 200mm Max distance table-tappet 320mm Single/Duration Stroke Shield Flywheel D600mm 400V 1.0kW Machine weight ca. 870 kg The purchase price is net. Can be viewed and tested in our warehouse. Delivery is possible at an additional cost. All information without guarantee!

Vertical baler HSM V-Press 860 plus, built in 2021 Technical data: Manufacturer: HSM Type: V-Press 860 plus Year of Make: 2021 Hours: 245 Pressing force: 60 t Drive power: 4 kW Filling opening: 1195 x 645 mm Filling height: 1114 mm Bale size: approx. 1200 x 1200 x 780 mm Bale weight: 480 kg Binding: manual Theor. Idle cycle time: 25 s Theor. Pressing capacity: 12 cbm/h Dimensions: 1800 x 1253 x 2990 mm (WxDxH) Weight: 2213 kg Materials: foil, paper, cardboard boxes Note: The press is in good condition. It has been checked and tested by us. You can find a video on our website or Youtube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offers are subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. Th ...

automatic baler Manufacturer: HSM Type: VK 42/800 Year of construction: 2002 specifications: Pressing force: 42 t Channel format: 700 x 800 mm (W x H) Binding: 4-fold horizontal Filling opening: 800 x 650 mm Drive power: 30 kW Optionally with conveyor belts

Here are the technical data of the offered machine: Technical data + information: • No-load speed up to 40 mm/sec • Opening speed up to 40 mm/sec • Starting press speed 5–15 mm/sec • Table size/heating plate size 600 × 600 mm • Plunger size/heating plate size 600 × 600 mm • 2 heating plates, electrically heated, up to 250 degrees – as OPTION • Total size approx. 2000 × 1000 × 2800 mm height • OIL temperature monitoring • Automatic lubrication • Free positioning of the plunger • SICK/LEUTZE light barriers 14.1 mm on the front • Circulating oil cooling • Pressure holding valve 0 to 1800 sec. • Rear monitored door • Pressure adjustment from 30 T to 120 T • Travel limitation either by pressure or position • Programming set-up mode, single stroke (adjustable via rotary switch) • Control panel permanently installed in the wall  ...

Type / type: N 25 Year of make: 1977 Manufacturer / make: Weingarten Rated pressure: 25 t Number of strokes: 140 / min Radius slide center to frame: 200 mm Window in frame: 240 mm distance table slide: 250 mm Stroke adjustment / adjustment of stroke: 8 ... 80 mm Ram adjustability/adjustment of ram: 50 mm Ram size / surface of ram: 355 x 220 mm Table size / surface of bed: 560x 400 mm Hole in table: 160 mm Power of main motor:3 kW Weight / weight: 2,23 t

Vertical baler HSM V-Press 860 plus, built in 2021 Technical data: Manufacturer: HSM Type: V-Press 860 plus Year of Make: 2021 Hours: 423 Pressing force: 60 t Drive power: 4 kW Filling opening: 1195 x 645 mm Filling height: 1114 mm Bale size: approx. 1200 x 1200 x 780 mm Bale weight: 480 kg Binding: manual Theor. Idle cycle time: 25 s Theor. Pressing capacity: 12 cbm/h Dimensions: 1800 x 1253 x 2990 mm (WxDxH) Weight: 2213 kg Materials: foil, paper, cardboard boxes Note: The press is in good condition. It has been checked and tested by us. You can find a video on our website or Youtube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offers are subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. Th ...

Specifications: Capacity: 60 t Passage between stand: 820 mm Working area, max.: 820 x 300 mm Piston stroke: 400 mm Flow speed: 6.1 mm/s Return speed: 10 mm/s Motor power: 3 kW Width: 1460 mm Depth: 850 mm Height: 2400 mm Weight, approx.: 700 kg Equipment: - Laterally movable cylinder - Spacious work area - Height-adjustable table - Torsion-resistant design made of welded steel -Manometer - Fine adjustment of pressure - Additional hand pump

Vertical baler HSM V-Press 860 plus, built in 2021 Technical data: Manufacturer: HSM Type: V-Press 860 plus Year of Make: 2021 Hours: 7 Pressing force: 60 t Drive power: 4 kW Filling opening: 1195 x 645 mm Filling height: 1114 mm Bale size: approx. 1200 x 1200 x 780 mm Bale weight: 480 kg Binding: manual Theor. Idle cycle time: 25 s Theor. Pressing capacity: 12 cbm/h Dimensions: 1800 x 1253 x 2990 mm (WxDxH) Weight: 2213 kg Materials: foil, paper, cardboard boxes Note: The press is in good condition. It has been checked and tested by us. You can find a video on our website or Youtube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offers are subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The  ...

Specifications: Capacity: 100 t Passage between stand: 1010 mm Working area, max.: 1010 x 300 mm Piston stroke: 400 mm Flow speed: 7.12 mm/s Return speed: 13.42 mm/s Motor power: 4 kW Width: 1600 mm Depth: 850 mm Height: 2450 mm Weight, approx.: 1000 kg Equipment: - Laterally movable cylinder - Spacious work area - Height-adjustable table - Torsion-resistant design with welded steel -Manometer - Fine adjustment of pressure - Additional hand pump

Roller compactor, miner - used - : Price from location: only 950.-€ (net) Manufacturer: Bergmann Type: PS 8100E Year of Make: 1990 Serial number: 05 3658 2845/90 Press pressure: to Net weight: 750kg 400V, 5.5kW, Condition: good Available: from Q4/2026 Location: Hamburg Efficient waste compaction: A special steel drum enables effective collection, crushing and compaction of the waste, reducing its volume by up to nine times. Continuous filling: The machine allows continuous filling by all users. The feed chute can also be left open during the work process, which facilitates and accelerates waste compaction.