127,247 used machines on RESALE, but how to find them? Machine Search
Key data: 48 KW, 60 kVA, 400 V
Execution: Category: Emergency Power Generator Stationary Aggregate type: stationary Design: Soundproofed Technical data engine: Engine manufacturer: Deutz AG Engine type: F 6 L 912 Motor power: 56 KW Cooling: Air-cooled Starting: Electric 12 V DC Speed: 1500 rpm Fuel: Low sulphur fuel oil Emission standard: TA-Luft Technical data generator: Generator manufacturer: Stamford Generator Type: S1L2-Y Generator power: 60 kVA Generator current: 86.40 amps Short-circuit current: 259.2 amps Overload: 95.04 amps Voltage 400 / 231 Volt Voltage regulator: yes electronic AVR Power factor: cos. - PHI 0.8 Speed: 1500 rpm Switchgear: Version: Automatic start Functions: Emergency power operation Switch: Generator switch 4 poles Delivery set up Base frame tank with drip pan Capacity / litre: 1 ...
5pcs power generator (power plant) total power : 6750KVA, was completely overhauled in 2017 equipped with new control and higher-level regulation., the system was responsible for the emergency power supply of a large data center until 2025 was always kept up to date with the latest technical standards and continuously maintained and serviced, the system is in excellent condition. Engine: Deutz MWM TBD604 BV12, 200h operating hours, year 1994, Pgebqwdsyzb R Tskpgok Generator: Siemens 1FC7 567, 10.000V, 50Hz, 78A, 1350KVA, Aggregate control: DEIF , Genset control, new Version Year 2016/17, Higher-level control: DEIF, Load management, synchronization, fuel managemente, ec. ec. Year 2017, Circuit breaker 10KV : Siemens Silencers, recirculating coolers, pumps, ec. ec.
Hydraulic power unit REXROTH consisting of: Hydraulic tank 250 Ltr. Electric motor 15 kW REXROTH Internal Gear Pump HYDAC Accumulator SCHMÖLE Heat Exchangers Temperature monitoring Hydraulic filter Return filter
Key data: 2000 KW, 2500 kVA, 10500 V
2x caterpillar 3520-C Unused genset! 0-Hours gensets are located in our warehouse for inspection adres: Kranenpool 10 6443VA Brunssum Netherlands check our website for more generators! generalpowerholland.nl +31681163153 what's app number
4 cylinder, engine runs but not with starter motor Auction-ID: A3-43520-17015
Key data: 70 KW, 63 kVA, 400 V
HAATS Gas CHP G 50 K Gas electricity and heat generator from 1999 with unknown operating hours. 1 available 50 KWel x 1,500 rpm, 400 V/50 Hz. AC Generator: Leroy Somer LSA C44.1 M3, 63 KVA Manufacturer: HAATS Model: G 50 K Type: Gas CHP Engine: MWB 12 NA-K (Mercedes engine block) Serial Number: GS50-113VLFN03089901 Power [KW]: 76 Power [KWel]: 50 Year of Make: 1999 Operating hours: unknown Weight unit [kg]: 2,500 Dimensions LxWxH [cm]: 360 x 120 x 200 AC Generator Leroy Somer LSA C44.1 M3 Manufacturer: Leroy Somer Model No.: LSA C44.1 M3 Type: AC Synchronous Generator Serial Number: FF089446/02 Power [KVA]: 63 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 91 Speed [1/min]: 1,500 Year of Make: 1998 Weight [kg]: 315
The VISCOTHERM Hydraulic Power Unit B/C 11–22 Z/HP is a powerful, robust pump unit for the reliable supply of the ROTODIFF hydraulic motor in decanter centrifuges. With an 11 kW electric motor, a gear pump (22 l/min at 270 bar) and integrated proportional control, it enables infinitely variable adjustment of the screw speed during operation. The 85-litre tank, an efficient oil/water cooler and extensive monitoring and protection components ensure safe and long-lasting operation – even under demanding industrial conditions.
Neat power harrow. Outside surface rust from standing in very neat and little-used condition. Auction-ID: A3-43520-17018
PRESS DESIGN drive system: eccentric / crank table cushion: yes PRESS FORCES total force (nominal): 63 to nominal work capacity: 630 kNm PRESS TABLE table surface (left-right): 900 mm table surface (front-back): 560 mm opening in bed (diameter): 250 mm SLIDE table surface (left-right): 450 mm table surface (front-back): 310 mm clamping surface diameter: 50 mm stroke: 100 mm stroke rate (max.): 100 /min SLIDE (MECHAN. PRESS) slide adjustment: 80 mm stroke min.: 17.5 mm stroke max.: 100 mm DIE CUSHION (TABLE CUSHION) number of cushions: 1 TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 340 mm distance table - slide max.: 440 mm ELECTRICAL SPECIFICATIONS total power consumption: 5.5 kW mains voltage: 380 V mains frequency: 50 Hz DIMENSIONS / WEIGHTS space requirements -left/righ ...
Steam Boiler CHP Power Plant with 240 MW Pyroflow CFB Boiler A combined heat and power (CHP) plant in very good condition, with an electrical capacity of 88 MVA and a thermal capacity of 240 MW. The plant is designed to operate primarily on wood-based biomass, with coal as a backup fuel. This is a complete power plant, still in full operation, and includes all technical systems from fuel feeding to the dispatch of electricity and live steam. The equipment has been exceptionally well maintained and extensively upgraded throughout its lifetime, meeting the most stringent modern quality standards. The steam boiler utilises Circulating Fluidised Bed (CFB) technology with the commercial-type PYROFLOW, manufactured in Finland by Ahlström in 1989. This CFB boiler delivers a steam flow of 100 kg/second at a pressure of 137 bar and a temperature of 535ºC. The primary fuel has been wood-ba ...
Key data: 20 KW, 400 V
Remeha Gas Generator ELW 20-43 Gas electricity and heat generator from 2014 with 51,151 operating hours. Closed unit with control. 20 KWel x 1,527 rpm, 400 V/50 Hz. Model No.: ELW 20-43 R0048 Type: Gas Electricity and Heat Generator Serial number: SK0714A-ETWD-020136 AC generator (asynchronous): Weier DASGM 225/45 AC Generator Speed [1/min] 1,527 Engine: Toyota Power [KWel]: 10-20 Power [KWth]: 29-46 Voltage [V]: 400 Current [A]: 37.5 Frequency [Hz]: 50 Year of Make: 2014 Hours: 51,151 Weight unit [kg]: 880 Dimensions LxWxH [cm]: 165 x 105 x 200
Outputs: 1x 400V & 1x 230V Auction-ID: A1-46037-2878
Combined Cycle CHP Power Plant 12.5 MWe + 1.6 MW Chilled Water This combined cycle CHP plant consists of one Dual Fuel Solar Turbine Mars 100 with 40 bar steam boiler, Siemens SST 060 Back Pressure Steam Turbine and one Double Acting LS Absorption Chiller with electrical, mechanical and control auxiliaries. Plant is maintained according to manufacturer’s instruction. Gas turbine engine was changed to Solar refurbished unit in June 2023 and it has accumulated only about 16000 hours since that. Both the gas turbine and the steam turbine were last overhauled by OEM service in mid-2025 and thus equipment is in good operational condition. This combined cycle CHP (trigeneration) plant delivers 10 MWe of primary electrical output from a Solar Turbines Mars 100 dual-fuel gas turbine, with an additional 2.5 MWe from a Siemens SST 060 back-pressure steam turbine and 1.6 MWth of chilled w ...
Without BATTERY Auction-ID: A7-46412-75
Hydraulic power unit in mint condition with accumulator for emergency stop operation for opening/closing 2 roller columns (smoothing unit, double trigger, etc.) unused, documents available
Rated Input Voltage: 1P AC380V ±15% 50/60Hz Rated Input Current: 14A Rated input power: 9.2 KVA Open circuit voltage: 256V Output Current Setting: 20-60A Rated Output Voltage: 104V Cyclic Duration Factor: 60% Efficiency: 70% Insulation class: F Protection class: IP21 Arc discharge by contact
- Powered by Kubota petrol engine. - Power: 5kva.
used hydraulic power unit with accumulator, for the operation of a screen changer
Equipped with Electrode holder with 2m cable; Grounding terminal 1.5 m; Cord length 1.50 m; chipping hammer; wire brush; Stepless regulator welding current 10-160 Ampere; Cycle of operation 10 minutes; Duty Cycle 35% 160A output; Product size 400x200x300mm (lxwxh); Product weight 2 kg; Power 160 W; Unused in box (Packaging size 500x300x400 mm (lxwxh), weight 6 kg)
Includes: transport box 1230x810x1030mm, various accessories.
including punching tools, machine is professionally disconnected and disassembled for loading on your transport, additional costs are mentioned separately during both
Power supply model Trio PS/1AC/24DC/5, used but in very good condition.
EA Electro-Automatic EA-EL 9080-170 B Laboratory Power Supply EA-EL9080-170B | EA-EL 9080 Item Condition: Used 6.3A 2400W PD 7,00 Financing by our bank is also possible. komplett-konzept.leasingo.de You can find more laboratory power supplies - new and used - in our shop! International shipping costs on request!
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 55 to PRESS TABLE table surface (left-right): 750 mm table surface (front-back): 450 mm SLIDE table surface (left-right): 400 mm table surface (front-back): 300 mm spigot hole diameter: 45 mm stroke: 50 mm stroke rate (max.): 100 /min SLIDE (MECHAN. PRESS) slide adjustment: 70 mm stroke min.: 6 mm stroke max.: 50 mm stroke rate (min.): 50 /min stroke rate (max.): 100 /min TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 310 mm ELECTRICAL SPECIFICATIONS mains voltage: 400 V mains frequency: 50 Hz DIMENSIONS / WEIGHTS space requirements -left/right-: 1200 mm space requirements -front/back-: 1500 mm total height: 2500 mm total weight approx.: 3850 kg ATTACHMENTS (PRESSES) strip feeder: optional fe ...
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 40 to PRESS TABLE table surface (left-right): 650 mm table surface (front-back): 380 mm thickness of bolster plate: 60 mm opening in bed (diameter): 120 mm SLIDE table surface (left-right): 350 mm table surface (front-back): 250 mm spigot hole diameter: 40 mm stroke: 78 mm stroke rate (max.): 145 /min SLIDE (MECHAN. PRESS) slide adjustment: 60 mm stroke min.: 8 mm stroke max.: 78 mm main drive power: 3 kW TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 297 mm ELECTRICAL SPECIFICATIONS total power consumption: 3.05 kW mains voltage: 400 V mains frequency: 50 Hz DIMENSIONS / WEIGHTS space requirements -left/right-: 1300 mm space requirements -front/back-: 1100 mm total height: 2150 mm total weig ...
PRESS FORCES total force (nominal): 100 to PRESS TABLE table surface (left-right): 950 mm table surface (front-back): 660 mm thickness of bolster plate: 68 mm SLIDE table surface (left-right): 540 mm table surface (front-back): 450 mm spigot hole diameter: 60 mm stroke: 130 mm stroke rate (max.): 65 /min SLIDE (MECHAN. PRESS) slide adjustment: 100 mm TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 370 mm DIMENSIONS / WEIGHTS total weight approx.: 7000 kg Located in Barcelona - Spain 2 identical units available
Hydraulic power unit, hydraulic pump, hydraulic test pump -Hydraulic unit with: 1x pump and pressure equalization -1x Hydraulic pumps: of type -1x pump max. pressure: 120 bar -1x pump max. flow rate: 30 l/min -1x Drive: 7.5 kW 1450 rpm -Hydraulic filter -Hydraulic tank -Dimensions: 1010/760/H1325 mm -Weight: 532 kg
maximum number of results exceeded
please refine your search
300 € 
