diesel man 20 used for sale

E-chain hoist, electric hoist, crane DEMAG type DKES 2-200 K V2 DIwith Dematik BUS control via crane system controlFabr. No.61456646 Year of construction 2003Lifting capacity: 200 kgHook travel: 4.0 metersMain lifting speed: 14.0 / 19.2 m/min. Fine lifting speed: 0.20 m/min. Chain size 4.2 x 12.2 mm1 Load train = 200 kg- with control logic DKES2/5 500V- without crane operation- Dematik BUS control via crane system control- without roller chassisMains connection: 400 Volt, 50 HzNominal power: 750 WNenncurrent: 2.4

Measuring and marking plate cast steel-grey cast iron heavily ribbed STIEFELMAYER comes from a measuring machine with a hand-held measuring armhigh-precision measuring plate with a good surfaceMasch. No. 8530979 Year of construction approx. 1989Length 5000 mmWidth 2000 mmThickness 350 mmWorking height 690 mmPanel thickness 50 mm throughout- 15 height-adjustable feet- very precise and stable longitudinal guides, screwed to the side of the plateSpace requirement L x W x H 5000 x 2120 x 400 mmWeight approx. 7500 kggood surface; used

Straightening and welding plate, cast steel-grey cast iron, heavily ribbedformer marking plate and measuring plateheavy straightening plateLength 2000 mmWidth: 1000 mmThickness: 240 mmWorking height: 850 mmPanel thickness approx. 30 mm throughout- 5 pieces height-adjustable feetWeight: approx. 1000 kgGood surface; used

E-chain hoist, electric hoist, crane STAHL type Si T 201-10/2,5No.: 1202373 year of construction 1989Load capacity 250 kgHook travel = lifting height 3.5 metersLifting speed 10 m/min. Fine lifting speed 2.5 m/min.2 load strands = 250 kgCable length of operating bottle approx. 1.4 metersMains connection 400 volts, 50 Hz.- Suspension eye on the top of the craneWeight: 22 kgGood condition; used

Chip conveyor, scraper conveyor with coolant tank BMF type KF 200 K17Ident. No: 0495078 Order No: 915979 year of construction 1992Metal link width 200 mmDistance driver bars approx. 380 mmLength of possible chip removal 1100/2100 mmInsertion length approx. 1350 mmInsertion height 370 mmInsertion width 460 mmHopper width at the top 400 mmHopper width at the bottom 170 mmConveying height - discharge height approx. 1250 mmMotor power belt drive 0.37 kWNetz connection 400 volts, 50 Hz- Drive of the scraper chain via geared motor-

Swing-cut guillotine shears KÖLLSCHEN type BSK 2000/2Fabr. No. 69 1307 Year of construction 1969Cutting length 2000 mmCutting thickness 2 mmStand projection 90 mmWorking height 920 mmMains connection 380 volts, 50 HzEngine power 4 kW- Drive via geared motor with brake and crankshaft- mechanical sheet metal hold-down- manual back gauge 500 mm- stop adjustment via 2 handwheels, rear on the backgauge guide with measuring scale- front side stop left 720 mm- electric foot switch- manual

Tig welding machine DALEX type GL/W 201TIG welding machineMachine no.: 201 0447 Year of construction approx. 1995Power 200 Amp. 35% ED 160 Amp. 60% ED 120 Amp. 100% EDEinfinitely variable adjustment rangeType DC - DCmains connection 400 Volt, 50 Hz, 5.9 kVA, 32 Amp. Plug- 2-stroke and 4-stroke welding device- TIG hose package 8 meters- HF ignition- Shielded gas pressure reducer- Electrowelding for rod electrodes- Fan cooling- Connection socket for foot switch (without foot switch)Space requirement L x W x H 850

Straightening and welding plate cast steel-grey cast iron heavily ribbedformer marking plate and measuring plateheavy straightening plateLength 2000 mmwidth 1000 mmthickness 160 mmworking height 850 mmplate thickness approx. 35 mm throughout- 3 pieces height-adjustable feetWeight with feet 680 kggood condition; used

Straightening and welding plate, cast steel-grey cast iron, heavily ribbedformer marking plate and measuring plateheavy straightening platelength: 2000 mmwidth: 1000 mmthickness: 260 mmworking height: approx. 850 mmplate thickness: approx. 40 mm throughout- 5 pieces, height-adjustable feetWeight with feet: 1250 kggood condition; used

Folding machine FASTI type 2095-25-2,5Fabr. No. 94 295 004 Year of construction 1994Useful length 2540 mmmax. Sheet thickness 2.5 mmStroke of the upper beam 380 mmMotor power bending beam 2.2 kWWetz connection 400 Volt, 50 Hz- NC control FASTImatic FM100- one-piece pointed rail 135- controlled back gauge- continuous stop rail- controlled bending angle via control- electric foot switchesWeight 3000 kggood condition; used

Straightening and welded plate cast steel-grey cast iron heavily ribbedheavyheavy straightening plateLength 2000 mmWidth 1500 mmThickness 125 mmBoard thickness approx. 40 mm continuousTable height 880 mm- Table base made of steel (self-made)Weight 1700 kgGood condition; used

a KM-200-1000 machine with removal robot built in 2006 for sale. The machine is in neat condition and serviced by Krauss Maffei.

turning diameter: 500 mm turning length: 1000 mm control: Mazatrol Smooth G number of spindle speeds: 5000 U/min spindle motor: 11/7,5 kW axis stroke (X,Y,Z): 450, 200, 960 mm travel -w axis: 950 mm b-axis: -30 / +210 ° c-axis: 360, 0,0001 ° bar material dia.: 65 mm milling spindle: spindle bore: 76 mm spindle turning speed range: 12000 U/min spindle motor: 7,5 / 5,5 kW tool taper: HSK A 63 rapid travel x/y/z: 40000 mm/min weight of the machine ca.: 9.5 t dimensions of the machine ca.: 3900 x 2600 x 2400 mm equipped with: - CNC control Mazak Smooth G - Main and counter spindle - milling spindle - Y-axis - Tool holder: HSK A 63 - Tool magazine: 72 places - Tool Eye - Mazak monitoring system B (RMP 60) - Coolant and compressed air (1.5 MPA) - Chip conveyor The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Max. saw blade diameter: 520 mm Cutting height: 200 mm at 90°, 140 mm at 45° Cutting length: 420 mm Mitre range horizontal: 45°-90°-25° Mitre range vertical: 60°-90°-30° Pneumatic material tensioners Minimum quantity spraying device Powerful 5 KW motor

Pressing Force max.: 2000 Kn, Withdrawal force max.: 1500 Kn, Supporting force in pressing position max.: 1200 Kn, Die return force max.: 50 Kn, Upper punch stroke: 220 mm, Upper punch adjusting travel: 200 mm, Number of strokes: 5-18 1/min, Filling height max.: 180 mm, Pressing travel max.: 90 mm, Withdrawal travel max.: 90 mm, Top pressing travel max: 18 mm, Upper punch pneumatic preload max.: 60 mm, Compressed air supply , Air consumption, Intake air aprox.: 140 1/min, Total connected load aprox.: 26,0 Kw, Width aprox.: 2350 mm, Depth aprox.: 3500 mm, Height aprox.: 5900 mm, Weight of the press aprox.: 19.900 Kg, Press housing: 260 l (gear oil), Workplace-related sound: 78 dB (A)

A Hämmerle hydraulic press brake is available. Pressing force: 2000kN, working length: 2600mm, installation height: 830mm, stroke: 265mm, throat depth: 300mm, rapid traverse: 100mm/s. Machine dimensions X/Y/Z: approx. 3750mm/2600mm/3600mm, weight: approx. 16000kg. The machine is not functional. Documentation available. On-site inspection is possible.

Travel X/Y/Z: 1300mm/900mm/1000mm, table dimensions X/Y: 2000mm/750mm, max. table load: 5000kg, rapid traverse: 6m/min. Machine dimensions X/Y/Z: approx. 3650mm/2700mm/2700mm, weight: approx. 9000kg, control: Heidenhain TNC 150. Documentation available. An on-site inspection is possible.

A right-sided Hebrock edge banding machine is available. Workpiece thickness range: 10mm-50mm, min. workpiece width: 70mm, min. workpiece length: 250mm, edge thickness (roll material): 0.5mm-5mm, max. edge height: 55mm, feed rate: 10m/min. Machine dimensions X/Y/Z: approx. 3000mm/1500mm/1300mm, weight: approx. 700kg. On-site inspection is possible.

ANGER HCP 203 Production GENERAL Project No.: 905739 Quantity: 2 pcs. Manufacturer: ANGER Type: HCP 203 Control: Siemens 840 D Year of manufacture: 2005/2013 Condition: Used machine Layers Machine Approx (Hrs): 2 Layers DESCRIPTION There are 2 production lines available. Each production line consists of three ANGER multi-spindle machining centers, each of which is connected to a KUKA robot. The loading and unloading of the EWAB conveyor belt is located at the back of the machines. ANGER (1) - 5-axis: 4 vertical milling and drilling spindles at the bottom, 4 vertical milling and drilling spindles at the top, touch probe at the top, 4 horizontal milling and drilling spindles at the left. Workpiece carrier with three linear axes and two rotation axes. ANGER (2) - 5-axis: 4 vertical milling and drilling spindles at the bottom, 6 vertical milling and drilling spindl ...

HYDAC ELECTRONIC, SET, Pressure Transmitter, HMG 2020-000-F + HDA + ETS Sensor Item condition: Used, in perfect condition For further technical data, please refer to the attached pictures. For further technical data, please refer to the pictures.

Pressing Force max.: 2000 Kn, Withdrawal force max.: 1500 Kn, Supporting force in pressing position max.: 1200 Kn, Die return force max.: 50 Kn, Upper punch stroke: 220 mm, Upper punch adjusting travel: 200 mm, Number of strokes: 5-18 1/min, Filling height max.: 180 mm, Pressing travel max.: 90 mm, Withdrawal travel max.: 90 mm, Top pressing travel max: 18 mm, Upper punch pneumatic preload max.: 60 mm, Compressed air supply , Air consumption, Intake air aprox.: 140 1/min, Total connected load aprox.: 26,0 Kw, Width aprox.: 2350 mm, Depth aprox.: 3500 mm, Height aprox.: 5900 mm, Weight of the press aprox.: 19.900 Kg, Press housing: 260 l (gear oil), Workplace-related sound: 78 dB (A)

Rheon V4 Stress Free Divider Type VX 202 -400 Year of construction: 2011 Output approx. 400kg /h Dough belt width 130-150mm Product weight approx. 50 -1,250g with single and double-row guillotine with spreading station with double-row weighing and outfeed belts with star cutter lubrication with 2 flours with digital control with funnel for approx. 50kg dough - overhauled and cleaned - Tapes, funnel mats, hoses, various bearings, etc. renewed - Availability: approx. 6-8 weeks after order

Two color pad printer GP 2002. The printer is intended for larger quantity jobs; closed system with foot pedal switch. Diameter of inside cup 6 cm. Format :215x100 mm. Available immediately.

Beck Wand 1000/2000 Extraction Wall Extraction wall Type: Beck Wand 1000/2000 Extraction wall made of sheet steel, with 5 suction slots made of perforated sheet metal evenly distributed. For connection to a central extraction system via a suction nozzle at the top center of the extraction wall. Cleaning opening can be unscrewed at the bottom of the front of the wall. Uses: Extraction of process air during grinding and milling Extraction of gases and light dust Extraction of powder mix or other stationary dust-forming processes Width: 1000 mm Height: 2000 mm + 100 mm nozzle Depth: 300 mm Suction nozzle: NW 250 top center Recommended extraction capacity: 3000 m3/h Paintwork: RAL 5018, RAL 7032 Weight: approx. 75 kg Manufacturer's price: 2970,-€ More items - new and used - can be found in our shop! International shipping costs on request!

Inv. Num. : 8570 Type: SU 50 A/2000 Producer: TOS Generated: Parameters: Maximum turning length: 2000 mm Maximum turning diameter over bed: 500 mm Maximum turning diameter via support: 250 mm Weight: 3260 kg Equipment: Digital measurement

for sale 2 MWM year 2010 hours 42 000 complete container installations

Rotary Brush Screen WESTFALIA BSB 200 Properties Type BOD 200 Machines No. 1 684 639 Total height 2500 mm Total length 600 mm Depth 600 mm Manufacturer: Westfalia Separator AG

STEIN Maschinenbau Profile Guillotine PT1-200 For glazing beads, small profiles, main profiles and technical profiles Max. cutting width: 190 mm, max. cutting height: 120 mm Extrusion speed: up to max. 10 m/min Blade length: 600 mm Length accuracy: +/- 2 mm Knife stroke: 180 mm Cutting speed infinitely variable Pneumatic quick-change device for knives Hold-down device pneumatic Knives are preheated: 80ºC - 160ºC Cycle time: 1.5 to 4 sec. adjustable on the display Infeed side: unit for applying a protective film to the profile Control: Compact PLC Siemens S7-613C Dimensions: Height: approx. 1,900 mm, extrusion height: 1,100 mm (+/- 50 mm height adjustment) Footprint: approx. 1,450 x 800 mm (without inlet and outlet tunnel) Condition: very good, ready for use

Crimper Manufacturer: Pamasol Type 2002/20 Capacity: 500-700 containers/hour The machine works pneumatically and is started with the two-hand solution. The crimping knife and crimp height can be adjusted to the desired dimension from the outside. Before closing the container, the machine presses the verntile onto the container with the set contact pressure. The contact pressure can be adjusted separately. Scope of application: container height 30-330 mm, container diameter 22-66 mm Operating pressure 8-10 bar Weight 75 kg Dimensions: 700 x 700 x 1000 mm

table length: 2000 mm table width: 1000 mm Plate thickness: 55 mm table height: 1000 mm plate height: ca. 200 mm weight of the machine ca.: 0,85 t dimensions of the machine ca.: 2x1x1 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

BILLION 200 T série HERCULE H 780/200 Force de serrage : 200 T - 2000 KN Groupe d'injection : H 780 Diamètre vis. : 50 mm Distance entre colonnes : 500 x 500 mm Dimensions des plateaux : 760 x 760 mm Epaisseur mini/maxi du moule : 280 - 580 mm Course d'ouverture : 560 mm Volume injecté : 422 cm3 Pression matière : 1843 bars Dimensions : 7,1x 2,1 x 2,6 m Poids : 14 000 kg

Main spindle: Spindle bore (I.D.): 80 mm Spindle nose: ASA A2-8 Revolver: Automatic 4-cavity turret SQT-190-87-C Lining (front): 3-jaw universal chuck ASA8 Diameter: Ø 315 mm Speed: 1250 rpm Inner Passage (I.D.): 103 mm Accessories: Set of 3 basic jaws Ø 315 mm Accessories: Set of 3 hard top jaws Ø 315 mm Accessories: Set of 3 soft top jaws Ø 315 mm Lining (back): 3-jaw universal chuck (rear) Diameter: Ø 315 Inner Passage (I.D.): 103 mm

EyeSys System 2000 Corneal Analysis System The EyeSys 2000 Corneal Analysis System is designed to provide unmatched performance, accuracy, ease of use, and affordability with these key features: Optimal central and peripheral corneal coverage provides complete information for the entire cornea Automatic calibration and automatic data correction ensure greater accuracy of topographic data. Automatic focusing and simple examination paths improve ease of use, speed up the examination process and virtually eliminate all focus differences between operators. Advanced software applications include primary care, co-management, corneal surgery, and contact lens fitting. The unique and patented three-camera technology provides a side-view image of your patient's cornea and enables the use of true aspherical image processing algorithms. Simultaneous positioning of the patient and opera ...

Tetra Pak TBA19 200 ml Slim Aseptic Filling and Packaging Line Complete aseptic carton filling and packaging line designed for 200 ml Slim cartons. This line combines proven Tetra Pak filling, straw application, shrink wrapping, and secondary packaging equipment, making it an ideal solution for dairy, juice, and beverage producers seeking reliable aseptic packaging technology. Line Configuration - The system includes the following Tetra Pak equipment: - Tetra Pak TBA19 200 S Filling Machine - Tetra Pak Straw Applicator 21 - Tetra Pak Multi Shrink Wrapper TFW 72 - Tetra Pak Cardboard Packer 70 - This configuration provides a complete production flow from filling to final carton packaging. 1. Tetra Pak TBA19 200 S Filling Machine - Manufacturer: Tetra Pak - Model: TBA19 200 S - Specification: 648160-0101 - Year of Manufacture: 1998 - Operating Hours: 16,727 h - Filling ...

DMG MORI CTX Beta 2000 CNC turning center was built in 2020 in Italy by Graziano Tortona S.r.l.. This extremely efficient machine is offered together with an extensive range of equipment, which significantly expands the machining capabilities and guarantees the achievement of high repeatability of the manufactured parts. Thanks to additional function packages, it is possible to perform, e.g. precise gear milling or polygon turning. All machining processes are performed inside a large working area by means of a reliable spindle and cutting tools taken from a 12-position turret. The tailstock coupled to the Z-axis moves collision-free on separate sliding guides, mounted on a bed of high thermal stability. This bed is excellent at reducing the influence of heat, while increasing the life of all components and tools. Over its service life, the machine has worked for a total of 6219 hours. ...

Name: CNC cylindrical grinder Machine type: Preise TT60-20L-C1 Machining size range - diam.: 600x2000mm Controller: Fanuc Series Oi Mate-MD

Production: KOJA Year of manufacture: 1990 Power: 200kW, 370A RPM: 1485 rpm Air delivery: approx. 100,000 m3/hour Suction side: diameter 800mm Pressing side: 800 x 620mm Impeller diameter: 1800mm Housing dimensions: 3400x3100x2400 Net weight with engine: approx. 4.5t Aerodynamic control with inlet guide vane, grease-lubricated anti-friction bearings. The machine can be disassembled and transported with a standard truck.

thickness of jaw: 200 mm Total length: 540 mm height: 125 mm max. clamping width: 320 mm width: 200 mm number: 2 Stück weight of the machine ca.: ca. 30 kg Machine vice 2 pieces Without crank The technical data are manufacturer or operator specifications and are therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then talk to us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thickness of jaw: 200 mm Total length: 540 mm height: 190 mm max. clamping width: 320 mm width: 200 mm number: 2 Stück weight of the machine ca.: ca. 30 kg Machine vice 2 pieces Without crank The technical data are manufacturer or operator specifications and are therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then talk to us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thickness of jaw: . mm Total length: 540 mm height: 125 mm max. clamping width: 320 mm width: 200 mm number: 2 Stück weight of the machine ca.: ca. 30 kg Machine vice 2 pieces Without crank Without jaws The technical data are manufacturer or operator specifications and are therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then talk to us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thickness of jaw: . mm Total length: 540 mm height: 125 mm max. clamping width: 320 mm width: 200 mm number: 2 Stück weight of the machine ca.: ca. 30 kg Machine vice 2 pieces Without crank Without jaws The technical data are manufacturer or operator specifications and are therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then talk to us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thickness of jaw: 200 mm Total length: 540 mm height: 125 mm max. clamping width: 320 mm width: 200 mm number: 2 Stück weight of the machine ca.: ca. 30 kg Machine vice 2 pieces Without crank Without jaws The technical data are manufacturer or operator specifications and are therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then talk to us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thickness of jaw: . mm Total length: 540 mm height: 125 mm max. clamping width: 320 mm width: 200 mm number: 2 Stück weight of the machine ca.: ca. 30 kg Machine vice 2 pieces Without crank Without jaws The technical data are manufacturer or operator specifications and are therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then talk to us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thickness of jaw: 200 mm Total length: 540 mm height: 125/190 mm max. clamping width: 320 mm width: 200 mm number: 2 Stück weight of the machine ca.: ca. 30 kg Machine vice 2 pieces Without crank The technical data are manufacturer or operator specifications and are therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then talk to us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thickness of jaw: 200 mm Total length: 540 mm height: 190 mm max. clamping width: 320 mm width: 200 mm number: 2 Stück weight of the machine ca.: ca. 30 kg Machine vice 2 pieces Without crank The technical data are manufacturer or operator specifications and are therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then talk to us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.