die spotting press used for sale

SINGLE POINT OPEN BACK INCLINABLE POWER PRESS Inv. No. 11.420PC Make IWK Model PEKRON 150Z Machine No. 1501 Capacity 150 tons Ram stroke 200 mm Ram adjustment 100 mm Shut height min/max 370 / 570 mm Strokes per minute 40 Knock out in ram 0 – 70 mm RPM 10 - 815 Throat 290 mm Power inclinable 30 degrees, 4kW Table 1000 x 630 mm Ram 760 x 410 mm Q 12 Volts 230 / 400 Cycles 50 Hz Including: Bolster plate 1.000 x 630 x 80 mm Bolster plate 1.000 x 630 x 90 mm Table opening, diameter 440 mm Updated electrics 2004 CE certified

Delivery date: 1961 Press force: 63 t Largest sheet thickness: 10 mm Stroke rate: 65 1/min Ram stroke: 8 - 100 mm Lifter adjustable: 63 mm Greatest distance between table and ram at max. stroke bottom, adjustment top, table bottom: 450 mm smallest distance between table and ram at max. stroke bottom, adjustment top, table top: 180 mm for further technical data see nameplates Table dimensions below: approx. 610 x 470 mm top table dimensions: approx. 310 x 260 mm

pressure: 25 t stroke: 100 mm table surface area: 440x320 mm ram surface: 360x220 mm hole in the table: 160x100 mm table height: 900 mm tool hole in ram: Ø 40 mm dayligth: 280 mm weight of the machine ca.: 1,5 t dimensions of the machine ca.: BxTxH 1500x1500x2100 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Pressure reducing valve, hydraulic valve ORSTA AS 16-2-01 TGL 10950 Nominal pressure: 16 MPa Dimensions: 220 x 130 x 70 mm

Machine number: 23620678 max. compressive force: 250 kN Largest stroke: 150 mm Drive power: 7.5 kW Operating voltage: 380 V Table dimensions: 570 x 380 mm

"Max. test pressure: 7 tons Max. distance from lower bearing: 2000 mm Max. distance from upper bearing: 600 mm Max. sample width: 250 mm Max. sample height: 200 mm" on pallet

pressure: 25 t throat: 250 mm stroke: 100 mm ram surface: 500x400 mm hole in the table: Ø 110 mm table height: 850 mm tool hole in ram: Ø 40 mm ram surface: Ø 150 mm weight of the machine ca.: 2,5 t dimensions of the machine ca.: 1500x2000x2200 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Pressure relief valve, direct controlled, hydraulic valve REXROTH DBDS 6 P 12/200 Setting pressure up to 200 bar Dimensions 145 x 60 x 40 mm

Equipped with 1 set of tools, please note the control is defective

Serial number: 055-007/12 Operating voltage: 220 V Frequency: 50 Hz Nominal current: 45 A Connection: 12.5 kW Control voltage: 60 W Press force: 25 Mp Operating pressure: 160 kp/cm³ Speed: 200 mm/s Sales: 450 mm/s Plunger stroke: 500 mm Projection: 360 mm Maximum distance between ram and table: 800 mm Table dimensions: 640 x 500 mm

pressure: 25 t distance between columns: 580 mm stroke: 150 mm dayligth: 370 mm table surface area: 560x400 mm ram surface: 400x350 mm hole in the table: 80 mm weight of the machine ca.: 2,5 t dimensions of the machine ca.: 1500x500x2500 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydro-electric piston pressure switch REXROTH HE D1 KA 40/100 ( HED1KA40/100 ) max 460 V 15 A Dimensions: 200 x 95 x 45 mm

On base and with vice

General overhauled, new seals etc.

"Lower counter bearing: 200mm Upper counter bearing: 600 mm Max. pressure: 35 kn"

Machine number: 0820592 max. load: 25 kN Throat: 90 mm Plunger strokes: 75 1/min Plunger adjustable: 30 mm Stroke adjustable: 2 - 40 mm Motor power: 0.25 kW Table dimensions: approx. 220 x 150 mm incl. The installed punching tool

pressure: 100 t passage width: 810 mm stroke: 400 mm table surface area: 1140x740 mm ram surface: 1140x740 mm dayligth: 670 mm weight of the machine ca.: 8 t dimensions of the machine ca.: 1800x1800x3000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Pressure Relief Valve, Hydraulic Valve ORSTA CNS 10-2-02 TGL 10947 Nominal pressure: 16 MPa New ! Dimensions: 105 x 35 x 35 mm

Equipped with 4 uprights and 8 beams and intermediate slats to place a wooden plate. Complete with side table with dimensions: 105x60x80cm and 4x zinc plate (antra) each with dimensions: 226x100cm

Equipped with shrinkage of 6-45 mm; Manual pump; Shrink force 1000Kn; 7 Sets of molds; Completion indicator light; Maximum opening diameter without mold: 50mm; Maximum opening diameter with mold: 40mm; Hydraulic tank capacity: 1L; Hydraulic oil capacity: 0.5L; Unused

Machine number: 2-0537 Compressive force: 28 kN Stroke: 60 Table dimensions: 200 x 160 mm Plunger: 60 x 35 mm

High Pressure Spray Gun ECCO 370R 8611 4170 50 See also W550 ! New, with Backing ! Dimensions ( Spray Gun ): 280 x 120 x 60 mm Dimensions( Package ): 280 x 120 x 60 mm

Fernvorgest. Pressure reducing valve, hydraulic valve BOSCH 0811 145 004 Pv: 7 - 315 bar Pmax: 315 bar New ! Dimensions: 145 x 90 x 85 mm

equipped with Delem CNC control and Wila hydraulic top clamping; Exclusive tools

max. load: 25 kN Projection: 90 mm Plunger strokes: 220 1/min Plunger adjustable: 30 mm Stroke adjustable: 2 - 40 mm Table dimensions: approx. 220 x 150 mm incl. The installed punching tool

Equipped with new control and laser protection from PILZ; including 1 set of tools with 2 V die sizes

High-pressure filter, with electrical maintenance indicator MAHLE PUROLATOR Pi 420 ( PUROLATOR Pi420 ) Pi 4211-13 ( Pi4211-13 ) 77666514 400 bar 110 l/min with used filter cartridge ! Dimensions: 410 x 170 x 100 mm

Pressure Switch ORSTA D5 CO 1 ( D5CO1 ) TGL 10952 Pn 32 MPa Dimensions: 195 x 90 x 65 mm

Length 3120 mm; WILA NS Recording

Machine number: 2-0095 Compressive force: 28 kN Stroke: 12 mm Safety distance: 100 mm Delay travel: 0.06 s Table dimensions: approx. 190 x 150 mm with pneumatic punching tool mounted

Machine number: 3-0419 Compressive force: 3 kN Stroke: 50 Table dimensions: approx. 150 x 110 mm

Hydraulic Hose Press; Crimping range: 15-63mm, Max aperture: 75mm, Voltage: 380V, Wattage: 3000W, Pressure: 53.5 Mpa Packing size: 780x540x1350 Weight incl. packaging: 280 kg Unused.

Pressure Reducing Valve, Direct-Operated, Hydraulic Valve REXROTH DR6DP 3-32/75Y ( DR6DP3-32/75Y ) R900541268 Maximum Secondary Pressure: 75 bar Maximum Operating Pressure: 315 bar New ! Dimensions: 170 x 44 x 42 mm

Pressure Relief Valve, Hydraulic Valve ORSTA 06-2.02.01 TGL 26233 / 20 used, tested ! Dimensions: 110 x 34 x 34 mm

Equipped with 3 crimp sets; unused

incl. foot switch

With foot switch, on metal base, self-made.

Machine number: 2-0151 Compressive force: 28 kN Stroke: 12 Table dimensions: 200 x 170 mm with punching tool mounted

Pressure relief valve with manifold, hydraulic valve ALLWEILER DS38-E-W111 opening pressure: 5 bar Qmax: 170l/min Dimensions: 310 x 70 x 65 mm

Pressure Control Valve, Hydraulic Valve VICKERS PRV1-10-C-0-24 used, tested ! Dimensions: 130 x 30 x 30 mm

Consisting of two punching stations, driven by pneumatic cylinders incl. Installed punching tool on pedestal Dimensions of the pedestal: 560 x 300 x 170 mm

Equipped with 10 crimp sets; unused