die spotting press used for sale

Palamine 80ton Upstroke Press (hot press) Platen size: 1525x1150 Daylight gap between top and bottom platen 185cm Max. temperature on platens 600 degrees Type of platen heating Electric 240V Overall footprint size 2160cm x 1525cm

pressure: 63 t throat: 275 mm stroke: 8-120 mm no. of strokes: 30-120 Hub/min ram - range of adjustment: 85 mm hole in the table: 220x100 mm table surface area: 750x540 mm ram surface: 400x260 mm table height: 820 mm tool hole in ram: Ø 50 mm total power requirement: 7,7 kW weight of the machine ca.: 5 t dimensions of the machine ca.: BxTxH 1500x2000x2450 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hand press pliers WMW Type: PZ 60.1-U with replaceable press jaws for Al and Cu conductors Dimensions: 640 x 220 x 50 mm

nominal force:100 t stroke:320 mm no. of strokes:35 /min distance between columns:360 / 250 mm Distance table/ram, max. stroke up, adjustment up:500 mm table surface area:320 x 450 mm table height over floor:660 mm ram surface:250 x 280 mm spindle diameter:125 mm power capacity:3,0 kW weight:4,5 t Dimensions (WxDxH):2,0 x 1,6 x 3,1 m

pressure:60 t distance between columns:650 mm stroke:220 mm distance table/ram, max. stroke up, adjustment up:410 mm table surface area:600 x 525 mm hole in the table:110 mm table height over floor:900 mm side window:200 mm ram surface:560 x 490 mm power requirement:15,0 kW dimensions (WxDxH):1,9 x 1,3 x 2,7 m foundation pit:not necessary

pressure:250 t distance between columns:1110 mm stroke:250 mm Distance table/ram, max. stroke up, adjustment up:500 mm Table surface area:1100 x 900 mm Table height above floor:950 mm Side window:690 mm Ram surface:1100 x 900 mm Oil volume:730 l Power capacity:56,0 kW Dimensions (WxDxH):2,3 x 1,55 x 3,96 m

nominal force:160 t stroke:140 mm no. of strokes:85 /min distance between columns:400 mm distance table/ram, max. stroke up, adjustment up:500 mm table surface area:400 x 450 mm table height over floor:800 mm Allowed max. force:230 t ram surface:400 x 320 mm spindle diameter:125 mm power requirement:7,35 kW weight:5,0 t dimensions (WxDxH):1,7 x 1,2 x 2,9 m

Capacity: 800 tons Stroke of slider: 400 mm Number of strokes per minute 12 Adjustment of slider: 185 mm Max. daylight betwen bolster and slider SDAU: 850 mm Table area: 1250 x 1650 mm Slider dimensions 1000 x 1250 mm Main motor power: 55 kW Distance between columns 1250 mm Cushion capacity, ton 125 Cushion stroke, mm 160 Press dimensions, mm 3800 x 2800 x 6900 Weight: 77 tons

pressure:300 t distance between columns:1800 mm stroke:1000 mm Distance table/ram, max. stroke up, adjustment up:1300 mm Table surface area:1600 x 1200 mm Table height above floor:1080 mm Ram surface:1600 x 1200 mm Weight:24,0 t Dimensions (WxDxH):2,8 x 2,1 x 6,0 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2

no. of strokes:150 /min impact energy:420 kJ distance lower die block / ram gudeway:435 mm Throat:425 mm steel forging - rectangular up to:110 mm steel forging - diameter up to:125 mm power requirement:22,0 kW weight of hammer:3,9 t weight of anvil:3,0 t ram hammer weight:200 kg weight:6,9 t dimensions (WxDxH):1,1 x 2,3 x 2,4 m

RODCRAFT WP100P workshop press ; hydraulic pneumatic and manual with 2 speeds ; suitable for pressing, straightening and assembly work ; Capacity: 100 tons; Air pressure: 7.5 – 8.5 bar ; Cylinder stroke: 300 mm ; Inner frame width: 787 mm ; Drevelset: yes ; Weight approx. 800 kg; Aged model

Machine number: H74/247 Press force: 4 Mp Oil pressure: max. 200 atm Motor power: 1.1 kW Table dimensions: approx. 250 x 250 mm

Maximum force ton-force 400 Slider stroke length mm 400 Slider strokes per minute 25 Maximum distance between table and slider (in lower position of slider) mm 470 Size of adjustment of distance between down-stamp a plate and slider mm 160 Table overall dimensions: mm ·from front to rear 1000 ·from left to right 1000 Slider overall dimensions: mm ·from front to rear 800 Main electric motor power kW 40 Press overall dimensions mm ·length 3470 ·width 3140 ·height 5940 Press weight kg 32600

Condition: unchecked Item is sold as is Weight may be ggbfs. Deviate. Machine must be dismantled by the buyer and transported out of the hall area. It cannot be guaranteed that a forklift is on site.

Brake 2x45 Nm, mounted on AUMANN substructure

V6 30 degree T mold set; length approx. 3.1 meters

HYDRASAN 350 T hydraulic press was built in 2007. There are 2 such machines available for sale. A price included in the offer applies to one machine. Technical specifications of the HYDRASAN 350 T press - maximum press force: 350 t - lower work table surface area (L x W): 1300 x 420 mm - movable table stroke: 300 mm - distance between tables: 400 mm - approach speed: 4.8 mm/s - return speed: 5.1 mm/s - piston diameter (cylinder internal diameter): 230 mm - directional control valve: REXROTH 4WE 10 G33/CG24N9K4 - pump flow rate: 40 l/min - oil tank capacity: 120 l - hydraulic oil gauge: PAKKENS - working pressure: 230 bar - manostat: REXROTH HED 80A 20/350 - electric motor power: 5.5/11 kW - electric motor rotational speed: 1450 rpm - power supply: 380 V; 50 Hz - dimensions of the HYDRASAN machine (L x H): 1800 x 2200 mm

Pressure Switch ORSTA D5 CO 3 ( D5CO3 ) TGL 10952 New ! Dimensions: 180 x 65 x 75 mm

Machine number: 6750296 max. load: 450 kN Throat: 230 mm Plunger strokes: 80 1/min Plunger adjustable: 55 mm Stroke adjustable: 4 - 80 mm Motor power: 4 kW Voltage: 380 V Table dimensions: 700 x 520 mm

Cabinet 1020x570x1000 Condition: unchecked Item is sold as is Weight may be ggbfs. Deviate. Machine must be dismantled by the buyer and transported out of the hall area. It cannot be guaranteed that a forklift is on site.

Stroke: 12 mm Compressive force: 28 kN Delay time: 0.063 s min./max. operating pressure: 3/6 bar Table dimensions: approx. 200 x 160 mm

Directivity: 100 t Projection: 325 mm Table size: 490 x 3500 mm Max. stroke: 160 mm Pushrod speed upwards: 206 mm/s Slide speed downwards: 68 mm/s Hydraulic drive: 380 V, 15 kW Space requirement: 3500 x 1650 x 2760 mm Weight: 5500 kg

Pressure relief valve, hydraulic valve ORSTA CDS 16 - 2 - 02 TGL 10947 used, tested ! Dimensions: 170 x 80 x 45 mm

Equipped with 10 crimp sets; unused

Machine number: 2561290 max. load: 250 kN Throat: 190 mm Plunger strokes: 80 1/min Plunger adjustable: 45 mm Stroke adjustable: 8 - 80 mm Motor power: 2.2 kW Voltage: 380 V Table dimensions: 555 x 430 mm

Equipped with 10 crimp sets; unused

Unused, crimping range 15-63mm, maximum aperture 75mm, 53.5 mpa, force 500 T, 3000W

Specifications Maximum pressure: 45 tons Year of Make: 2017 Pressing force: 6.9 kg/cm² Number of bindings: 3 Channel cross-section: 900 × 720 × 600 - 1200 mm Dimensions of the tailgate: 820 × 1250 mm Bale weight: 250 - 400 kg Weight: approx. 7 t Power connection: 400 V Bale tying: automatic Theoretical throughput 174 m3/hour Theoretical throughput to density 20 kg/m - 3.48 tons/hour Theoretical flow rate to density 50 kg/m - 8.7 tons/hour If you have any questions, please call us: +48 696 072 985

consisting of stamps in different designs and sizes

Unused, crimping range 15-63mm, maximum aperture 75mm, 53.5 mpa, force 500 T, 3000W

We sell our PPK baler. the main pump and auxiliary pump were replaced this year 2024. Invoices are available. The press only pressed cardboard boxes. It can be demonstrated and put into operation at any time.

Pressure relief valve, hydraulic valve ORSTA CDS 16-3-02 TGL 10947 Nominal pressure: 16 MN/m² used, tested ! Dimensions: 140 x 45 x 45 mm

Equipped with 10 crimp sets; unused

Machine number: 35-173-98 Serial number: 2-0499 Compressive force: 4.5 kN Stroke: 60 mm incl. transport trolley

Inv. Num. : 8131 Type: HPD-S 63 Producer: Hydrap Created: 1997 Parameters: Compressive force: 63 t Stroke: 1000 mm Maximum lifting speed: 410 mm/s Machine height: 2200 mm Machine length: 1200 mm Machine width: 500 mm Machine weight: 13000 kg

Pressure relief valve, hydraulic valve ORSTA CNS 16-2-02 TGL 10947 Nominal pressure: 16 MPa used, tested ! Dimensions: 160 x 80 x 45 mm

Volume 350 L

max. bar: 400 Serial number: 2121 Press force: 150 t Table dimensions: approx. 1500 x 560 mm Max. stroke: approx. 250 mm

Hydraulic Hose Press; Crimping range: 15-63mm, Max aperture: 75mm, Voltage: 380V, Wattage: 3000W, Pressure: 53.5 Mpa Packing size: 780x540x1350 Weight incl. packaging: 280 kg Unused.

Inner diameter: 220 mm Inner belt width: 200 mm Year of construction 02/90 Load capacity per reel is 150 kg, whereby the reel must be screwed to the ground. Weight approx. 450 kg Incl. wiring diagram

Pressure Switches ORSTA D5 CO L32 ( D5COL32 ) TGL 10952 Dimensions: 150 x 65 x 65 mm New !

Equipped with 10 crimp sets; unused

Equipped with shrinkage of 6-45 mm; Manual pump; Shrink force 1000Kn; 7 Sets of molds; Completion indicator light; Maximum opening diameter without mold: 50mm; Maximum opening diameter with mold: 40mm; Hydraulic tank capacity: 1L; Hydraulic oil capacity: 0.5L; Unused

Length approx. 3.2 meters; 13 mm lip