deutz ag used for sale

FLATBED UV LARGE FORMAT PRINTER M. No.: 2525797057901 • CMYK + Lc Lm + 2 x White • White in the pre- and postprint • Speeds up to 45 m²/hr. (500 ft²/hr) • Max. print size 2,54 x 1,54 m • Substrates up to 4,5 cm (1.77 in) thick. • Multiple board printing • Borderless printing • Shuttle safety sensors • For Digital Printers, Poster printers and Mid-Size Graphic Screen Printers

pressure: 10 t distance between columns: 260 mm dayligth: 210 mm table surface area: 275 x 260 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Agilent G 1310 A Isocratic HPLC Pump Flow Range 0.001-10 ml/min

Agilent G 1330 ALS Therm ASgilent Autosampler Thermostat for 1100/1200 HPLC Systems

frequency: 50 Hz weight: 3000 kg voltage: 3 x 400 V output: 8,3 kw ampere: 12 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

An Agie start hole drilling machine for the EDM industry is available. Travel X/Y/Z: 300mm/200mm/300mm, electrode diameter: 0.3mm-3mm, max. drilling depth: 200mm, table dimensions X/Y: 400mm/300mm, max. workpiece weight: 300kg. Machine dimensions X/Y/Z: approx. 1400mm/900mm/2000mm, weight: approx. 950kg. Documentation available. On-site inspection is possible.

Installation space (x,y,z): 297 x 210 x 200 mm, printing technology: Multijet technology, Layer thickness: 20µ, 15µ, resolution xy: 635 x 400 DPI, equipment: Software, cable, heat bath, file formats: STL, network connection: Ethernet, mass: 188 kg, Dimensions: 1360 x 944 x 700 mm (H x W x D), mains voltage: 100 - 240V, 50/60Hz,single phase, max. 750 VA, Legal regulations: CE approval mark, Installation: 2015, Accessories post processing: On demand, Net installation space for models: 297 x 210 x 200 mm, printheads: 1 piece, Interface: Modeling Studio, software: Windows 32Bit / 64Bit, printing material: AR-M2 (transparent printing material), AR-H1 (heat-resistant printing material), AR-G1L (silicone rubber [low hardness]), AR-G1H (silicone rubber [high hardness]), support material: AR-S1 (water soluble support material), Accessories post-processing: On demand, Installation space (x,  ...

Travel X/Y/Z: 500mm/350mm/500mm, table dimensions X/Y: 800mm/600mm, max. table load: 800kg, work bowl dimensions X/Y/Z: 860mm/620mm/350mm, max. electrode weight: 200kg, tool positions: 28, machine dimensions X/Y/Z: approx. 3000mm/3750mm/3000mm, weight: approx. 3340kg. Documentation available. On-site inspection is possible.

table length: 500 mm table width: 350 mm ampere: 65 A Control: AGIEVISION 5 CNC total power requirement: 20 kW weight of the machine ca.: 4000 kg dimensions of the machine ca.: m A G I E (Switzerland) CNC - Controlled Wire Cutting EDM Machine Model AGIECUT PROGRESS V 3, Year 2007 Working range, X Y Z (=height) 500 x 350 x 426 mm Wire head, U-V axis (helical/taper cuts) + / - 30 °/ +/- 70 mm Resolution of axes 0.0001 mm Speed for positioning the axes up to 3 m/Min. Tolerances (If machine is new) 4 µ Workpiece dimensions, L x W x H max. 1.050 x 650 x 420 mm Max.weight of workpiece with/w.o. Dieelektricum 400/800 kg Clamping System Universal Beams with fixing holes Cutting wire Ø 0.2 – 0.33 mm Size of wire roll up to 25 kg Cutting speed of wire  ...

Ref. 499 Stitching machine Agrafix BX Ma No. 17007 Condition: Used machine / Cleaned and checked / Functional Ref. 499 Stitching machine Agrafix BX Serial 17007 Condition: Used machine / Cleaned and checked / Good working condition

Average output 800-1200 kg/h depending on materials and moisture, HORIZONTAL STORAGE BELT, DIAGONAL LOADING BELT AGGLOMERATOR D1300 Steel barrel diameter 1300 mm. Main motor 250 kw (available with 300 kw motor on request) Replaceable inner steel lining Side door for inspection and blades replacement, Sucking vent for steam extraction Oleodynamic power station 0,75 kw with electrovalve which controls opening of unloading door.water loop cycle for cooling hub bearings belt. Electrical cabinet Dimensions: L mm.3950, W.mm.2.280, H. mm.4652. DISCHARGING HOPPER Diagonal, engine moved auger for material extraction (1,1 kw) Discharging height 830 mm from ground Depressure pipe inspection window safety inner grid Appx dimensions : 1000×1500 mm. Auger diam.180 mm. The line is offered reconditioned. Complete with electrical drawings and user manual. We provide spares+repairs+accessories service al ...

Key data: 700 mm, 680 mm

NRA700 Band Saw Brand: Agazzani M-No.: Year of construction: Motor 2.2kW Table surface: 740640mm Wiel diameter: 700mm Cutting height: 405 mm Band width: 680mm Band Saw Length: 5020/51400mm Band saw width: max. 40mm Tilt (table): 45° Table Levels: 960 Suction support: ø120 mm Machine dimensions: 1.3506702.170

1-stitching head machine AGRAFIX BX Saddle stitching (swivel table) Stapling thickness 1 sheet up to 25 mm with backwards folded staples Grooving (stitching) up to 40 mm thick Clamp width 14mm Round Wire No. 30-21 + Flat Wire No. 0-V Projection 320 mm Stapling table 610 x 200 mm Dimensions W65 x D70 x H160cm Packaging dimensions W80 x D90 x H180cm, 240/300kg Drive 220/380 Volt, 50Hz, 1/3 HP

pressure capacity max.: 80 t Stroke: 500 mm table surface area: 960 x 810 mm spindle pitch: 72 daylight between the columns: 950 / 540 mm passage: 640 mm machine weight ab.: 4500 kg dimensions of the machine ca.: 2,0 x 2,0 x 3,85 m Hydraulic quick adjustment 500mm Flywheel Ø2000mm 4 prism bases for straightening waves different support frames The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

• Manufacturer: AGI • Model: TOWER A3W • Year of construction: 2017 • Machine Type: Polymer Plate Processor • Machine type: Prepress machine for flexographic printing • Max. plate format: DIN A3 (297 mm x 420 mm) • Application: Development and processing of photopolymer plates • Application: Label printing, packaging, flexographic printing • Compact design, ideal for small to medium-sized printers • Condition: Very well maintained, ready to use

An Agfa UV-LED hybrid large format printer including a roll-to-roll unit is available. Printing technology: UN-LED inkjet, max. print width: 2540mm, resolution: 1200dpi, print colors: CMYKLcLm+white+primer, max. print speed: 275m²/h, substrate type: rigid/flexible, max. substrate thickness: 50mm. Documentation available. On-site inspection is possible.

x-axis: 550 mm y-axis: 350 mm z-axis: 400 mm U-axis: 550 mm V-axis: 350 mm volume: 1200 L inclination: +/-30°/400 mm dimensions: 1200x700x400 mm weight: 1500 kg wire dia.: 0,10-0,33 mm Bobbin Weight max.: 25 kg total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Agilent 1100 HPLC -Agilent G 1311A quaternary pump (or bin.) -Agilent G 1315B DAD Diode Array Detector -Agilent G 1313A autosampler -Agilent G 1316A Colcom -Agilent G 1322A Degasser Solvent Box Complete with Agilent Chemstation on request

ERMAFA AGGLOMERATOR, SPS-System: Siemens S5 – 95U, Average throughput rate:, LDPE: 500kg, OPP: 300-400kg, TPO: 300-400kg, Including:, buffer silo with automatic filling of the agglomerating chamber through pneumatic system, automatic discharging of agglomerated material, Agglomerator, 355 kw drive, Control system, Control cabinet, Extraction system/filter, Classifier, small conveyor belt, Spare parts available:, 1x knife shaft, 35 knifes, Other spare parts need to be produced., Constructed in 1993, used by Constructor for test purposes until 2006, The machine has been working until 3rd quater 24, then disconnected in Feb 25 (after video), installed power - used power in work: about 60-65% : 355, availability: immediate, capacity: 300-500 kg/h depending on materiale and feeding rate, conditions: good working conditions

From old stock HP Power Sensor unused !

Machine is in good technical condition, a visit and a test run are possible by prior arrangement.

Working range: 1.050 x 650 x 250 mm max. workpiece weight: 400 (800) kg control: Agievision AGIE max. conicity: 30° / 100mm travel -x axis: 500 mm travel -y axis: 350 mm travel -z axis: 426 mm travel U x V-axis: +/-70 / +/-70 mm rapid traverse X-axis: 3 m/min rapid traverse Y-axis: 3 m/min rapid traverse U-axis: 0,6 m/min rapid traverse V-axis: 0,6 m/min rapid traverse Z-axis: 0,6 m/min wire dia.: 0,2...0,33 mm total power requirement: 12,1 kVA weight of the machine ca.: 3,9 t dimensions of the machine ca.: 2,8 x 2,4 x 2,3 m Documents: Wire Eroding Machine AGIE - Agiecut Progress 3 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Brush kit and rollers Agfa Elantrix 95 SX; used. Brush Kit and rollers for Agfa Elantrix 95 SX; condition used.

X-axis: 400mm, Y-axis: 250mm, Z-axis: 256mm, max. workpiece weight: 400kg, max. workpiece dimensions: 580/860/250mm, support surface: 680/500mm, min. start hole diameter: 2mm, cutting rate: 185mm²/min, generator: Agiplus-MMD, control: Agimatic CF20. With dielectric processing unit DA-15/C. The display power supply is defective. The machine has already been dismantled, an on-site inspection is possible.

The machine is in good technical condition, testing possible after prior agreement. Table dimensions: 700 x 450 mm Z-axis travel: 255 mm Y-axis travel: 250 mm X-axis travel: 350 mm MACHINE DIMENSIONS: L: 2100 mm x W: 2000 mm x H: 2200 mm

Agfa Avalon N4-30 PT-R4600E, Year 2018 only approx.16K plates done Apogee Workflow RIP Inline punch Stacker ST 95EX Azura C95 Clean out unit Etc. Available: at short term

Flame atomic absorption spectrophotometer AGILENT FS 240 complete set

AGFA Acento E (Screen 4100 E) year 2006 16 diodes plate winding cycles 66.600 exposure time 5,800 h PC with ApogeeX good condition

CNC vertical machining center Type: Mikron VCE 800 Pro Manufacturer: GF AgieCharmilles Year: 2011 Control: Heidenhain iTNC 530 X: 800 mm Y: 500 mm Z: 540 mm Table: 910 x 500 mm Max table load: 1100 kg Max spindle speed: 14000 rpm Tool magazine: 24 positions Machine weight: 5000 kg Cooling and rinsing through the center of the spindle. Work and tool probe included New spindle in 2018 Machine in good condition, under power Find more here - / Contact us at -

Agilent 5110 SVDV which YOM 2018 for sale. It's an complete set including chiller, autosampler SPS4 and software.

AGEMA high-speed drilling machine AS 210 The machine is assembled and functional in the showroom. • Well-maintained machine. • Built in 2007 • Tank has been cleaned • Electrode diameter: 0.15 up to 3 mm • Maximum drilling depth: 100mm • Max workpiece weight: 20kg • X, Y, Z travels: 200 x 100 x 140 mm

EDM machine Agie Charmilles Cut e 600 BJ 2018

Max workpiece size 1030x800x350 mm Table size 950x630 mm Can be inspected under power

Used manual batch ultrafiltration line for cottage cheese made by Agros Milko-Polska. Capacity: 2.500 kg of finished product in 8 hours, concentrated to 72% dry matter. New: 1996

The machine is in good technical condition, testing possible by prior arrangement. 20,000rpm, 24,000 hours, iTNC 530.

CTP plate setter Advantage DL+ Plate developing machine VPP 68 Find more here - / Contact us at -

Manufacturer: ACA Model: AGN2D2 Year of Manufacture: 2020 Condition : Good Weight: 1500 kg Input Voltage: 240V / 50Hz Phase: Single Power: 1500W Full Load Current: 7A Short Circuit Current: 30mA Find more here - / Contact us at -

Components: control cabinets, machine body (cabin, turbines, outlet, inlet), platform with processing unit and bunker, sound insulation cabin, impact box, bucket elevator, gratings, ladder, pre-impact box, small parts, piping, cable ducts, blasting media and refill silo, compressed air connection: 1/2 inch at 4–6bar, compressed air consumption: approx. 1.5m³/h, processed according to DIN ISO 8573-1, solid particle size: 1µm, density: 1mg/m³, water content: pressure dew point 3°C, oil content: 1mg/m³, length: 11,000mm, height: 5907mm. An on-site inspection is possible.

General SKU437W1436 LocationBarneveld MakeAgilent Type1100/1200 series Year of constructionunknown Specified Features - Miscellaneous Motor230 volt Information Floor space0,60x0,60 m CEcheck Total height1,0 m Weight50 kg Extra SpecificationsWith Thermostar, FC/ALS therm, Degasser, Detector, :MiscellaneousAgilent TechnologiesMiscellaneous > MiscellaneousBrand > Agilent Technologies What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

SPECTOMETER AGILENT CARY 600 FTIR in excellent condition

Key data: 230 KW, 275 kVA, 400 V

2G Gas CHP Agenitor 206 Gas electricity and heat generator from 2011 with approx. 60,000 operating hours, CHP (closed unit) with control and cooling. 1 available 220 KWel x 1,500 rpm, 400 V/50 Hz. AC Generator: Leroy Somer LSA 46.2VL12 B6/4, 275 KVA Manufacturer: 2G Model No.: agenitor 206 Type: Gas CHP Serial number: MH1011B-EGLB-220094 Engine power [KW]: 230 Electrical power [KWel]: 220 Year of Make: 2011 Operating hours: approx. 60,000 Weight unit [kg]: 3,600 AC Generator Leroy Somer LSA 46.2VL12 B6/4 Manufacturer: Leroy Somer Model: LSA 46.2VL12 B6/4 Type: AC Synchronous Generator Serial Number: 273097/1 Power [KVA]: 276 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 398 Speed [1/min]: 1,500 Year of Make: 2011 Operating hours [h]: approx. 60,000

Manufacturer: AGIE Model: FUTURA V 1PM Electrical Specifications: - Voltage: 400 V - Frequency: 50/60 Hz - Phase: 3 PH - Circuit Breaker Power: 17 kVA - Power Factor (Cos φ): — - Full Load Current: 15 A - Full Load Power: 3.9 kVA - Amp Rating of Largest Motor/Load: 3.4 A - Overcurrent Protection: 20 A @ 480 V ~, 18000 AIC Weight: 265 kg Condition and Maintenance: Last service performed at the end of 2021 (running hours: 9107). The machine has been used only a few hundred hours since. Overall in good condition. Find more here - / Contact us at -

Used vegetable washer made by Maquinaria Agricola E Industrial, model: LAVSIM-D4X12. Capacity 6 tones / hour for beetroot. Length: 3 m

Inv. Num. : 8808 Type: MS-1.2 Producer: Agropart Created: 2025 Parameters: Volume: 1700 m3 Power: 2400 kg/h Equipment: Large Pocket Tower Fan

Wire stapling machine with 2 stapling heads for 0-25mm stapling

Travel X/Y/Z: 450mm/350mm/400mm, travel U/V: approx. +/-70mm, rapid traverse: 900mm/min, max. workpiece dimensions X/Y/Z: 1050mm/650mm/250mm, max. workpiece weight without/with tank: 800kg/400kg, wire diameter range: 0.2mm-0.33mm, tank volume: approx. 750l. Machine dimensions X/Y/Z: approx. 2000mm/2300mm/2500mm, weight: approx. 4000kg, control: Agievision. Documentation available. An on site inspection is possible.

Code: 0281 Brand: AGLA GALLI Model: 2 R 130 Automatic 2 roll polishing machine for polyester and varnish - It is suitable for buffing of high gloss polyester or polyurethane paints, metals, marble and similar materials N° 2 inclined rollers - Thanks to this inclination, the rotating brushes, by oscillating, ensure a perfect polishing of the surfaces to be treated REVERSE" system , which restrains softens the reverses even with heavy materials like marble, wooden panels, etc. Length of 2 rollers mm 1300 Roller diameter mm 300 Useful working length mm 4300 Useful working width mm 1300 Max panel height mm 120 Motor hp 15 x 2 Working table height from mm 950 to mm 1180 Suction mouth diameter mm 200 Overall dimensions mm 5000 x 2350 x 1750 h Weight kg 2500

For plastic scraps, in most cases without need to reduce size The offer includes:, STORAGE HORIZONTAL BELT, to grant non-stop feeding, DIAGONAL LOADING BELT, made in sturdy carbon steel with side walls, dragging paddles, PVC carpet, AGGLOMERATOR with barrel Ø1.500 mm.,, length 4300 mm. width 2300 mm. height 5.050 mm. 560 kw , Hp 730 65% used in work Side opening panel for inspection and replacing blades Operator switchboard, Exchangeable inner steel liner for barrel Oleo-dynamic power station 0,75 kw with electro-valve opening, Hub temperature control system, Grease lubricated drive bearings, 0,4 kw ventilator for belt cooling with air conveyor, Steam sucking vent 4 kW UNLOADING HOPPER, complete with 200 mm Ø, diagonal auger for agglomerated material 1,5 kW drive., size 1.150 mm. x 2.000 mm. Lower opening for cleaning purposes Operations, upper lid, two inspection windows (one can be o ...

Haug AG35 generator charging unit for making products static or antistatic See soecificationa in the pictures