demag p 625 used for sale

indoor crane, crane, electric wire rope hoist, hoist, motor cable winch, motor winch, tackle, pulling winch, pulley block -Handover: in the current condition as viewed -Condition: Operation is missing a switching element (can be installed for an additional charge) -Engines: tested and OK -Nominal load: 1125 kg -Lifting speed: 6.3 m/min -Lifting height: 6.3 m -Dimensions: 1100/1000/H700 mm -Weight: 368 kg

Indoor crane, crane, push carriage, crane running gear, crane undercarriage, girder carriage, headcarriage for bridge cranes, ceiling crane headcarriage, headcarriage single girder bridge crane -Friction wheel Demag type: RF180 -Carrier width: 120 mm -Load capacity: 2000 kg -Number: 2x drives available -Price: complete -Dimensions: 2550/320/H350 mm -Own weight: 500 kg

Indoor crane, crane, push carriage, crane running gear, crane undercarriage, girder carriage, headcarriage for bridge cranes, ceiling crane headcarriage, headcarriage single girder bridge crane -Handover in the current condition as viewed -1x wheel missing (photos) -Friction wheel Demag type: 13/8RF8-2 -Carrier width: 120 mm -for narrow flange beams: IPE240 (120 mm wide) -the chassis are inserted into a steel beam -Load capacity: 2000 kg -Number: 2x drives available -Price: complete -Dimensions: 2550/320/H350 mm -Own weight: 500 kg

Gear motor, electric motor, stop motor, drive motor, crane motor, bridge crane -Manufacturer engine DEMAG type: KBA-112-MB-6 -Manufacturer engine DEMAG type: KBL-71-A4 -Manufacturer gearbox DEMAG type: FG08-B-14-U-0-H1- -Power: 0.3/2.9 kW -Speed: 106/945 rpm -Construction: B14 -Diameter shaft: Ø 28 mm -Protection class: IP 54 -Dimensions: 670/300/H500 mm -Weight: 102 kg

Column jib crane, overhead crane, workstation crane -Manufacturer: DEMAG, Column jib crane, lifting capacity 250 kg -Base plate: 550 x 550 mm -Protrusion: 2,860 mm -Total height: 5110 mm -Hook height: 3170 mm -Swivel range: 270° -Chain hoist: can be supplied for an additional charge -Transport dimensions: 5110/800/H550 mm -Weight: 380 kg

Control cabinet and distribution board construction, busbars, distribution cabinet, power distributor, housing, universal housing, electronics housing, distribution box -Manufacturer: Mannesmann Demag, electronics housing from injection molding machine Demag D 100-275 NC -Ident. No.: 06594865 -Dimensions: 200/200/H90 mm -Weight: 1.1 kg

CNC control, control panel, control panel, control unit, card slot, control cards, MC3 control, plug-in cards, circuit boards, valve module, valve amplifier, circuit card, analog distribution card, distribution board card, valve amplifier, bus print, bus board, processor card, coupling card, temperature control card -Manufacturer: Bachmann, control electronic modules from injection molding machine Demag D 100-275 NC -Card holder: Murrelektronik 630055 -Control card: Philips 9404 780 020 -Individual components: see photos -Price/sale: complete -Total dimensions: 315/140/H215 mm -Weight: 1.4 kg

CNC control, control panel, control panel, control unit, card slot, control cards, MC3 control, plug-in cards, circuit boards, valve module, valve amplifier, circuit card, analog distribution card, distribution board card, valve amplifier, bus print, bus board, processor card, coupling card, temperature control card -Manufacturer: Mannesmann Demag, control electronic modules from injection molding machine D 100-275 NC -Card holder: Murrelektronik 630055 -Control card: Philips 9404 780 020 -Individual components: see photos -Price/sale: complete -Total dimensions: 315/140/H215 mm -Weight: 1.4 kg

CNC control, control panel, control panel, control unit, card slot, control cards, MC3 control, plug-in cards, circuit boards, valve module, valve amplifier, circuit board, analog distribution card, load amplifier, load amplifier -Manufacturer: bg Bernd Grigat, load amplifier from injection molding machine Demag D 100-275 NC -Type: QVA 30/1 Item No.: 2442/00 -Quantity: 2x amplifiers available -Price per piece -Total dimensions: 100/40/H110 mm -Weight: 0.3 kg/pc.

Transformer, transformer, converter, three-phase autotransformer, three-phase transformer, three-phase transformer, single-phase transformer -Manufacturer: Tramag Fürth, transformer type CST from injection molding machine Demag D 100-275 NC -A-No.: 80258 ID.No. 06520365 -Power: 1100 VA -Technical data: see photo nameplate -Dimensions: 240/120/H220 mm -Weight: 16 kg

CNC control, control panel, control desk, operating unit, card slot, control cards, MC3 control, plug-in cards, printed circuit boards, valve module, valve amplifier, printed circuit board, analog distribution card, distribution print card, valve amplifier, bus print, bus board, processor card, coupling card, temperature control card -Manufacturer: Siemens, control electronic modules from injection molding machine Demag D 100-275 NC -Power supply: Type E220 G5/15WRGD -Adapter capsule: Type 6ES5 491-0LB11 5 pieces -Interface modules: 6ES5 306-7LA11 -Subrack: 6ES5 700-2LA11 -Individual components: see photos -Price/Sale: complete -Dimensions total: 485/220/H305 mm -Weight: 12.3 kg

CNC control, control panel, control panel, control unit, card slot, control cards, MC3 control, plug-in cards, circuit boards, valve module, valve amplifier, circuit card, analog distribution card, distribution board card, valve amplifier, bus print, bus board, processor card, coupling card, temperature control card -Manufacturer: Siemens, control electronic modules from injection molding machine Demag D 100-275 NC -Interface modules: 6ES5 306-7LA11 -Digital output: 6ES5 454-7LB11 5 pieces -Digital input: 6ES5 430-7LA11 3 pieces -Subrack: 6ES5 701-2LA12 -Individual components: see photos -Price/sale: complete -Total dimensions: 480/210/H305 mm -Weight: 11.2kg

CNC control, control panel, control panel, control unit, card slot, control cards, MC3 control, plug-in cards, circuit boards, valve module, valve amplifier, circuit card, analog distribution card, distribution board card, valve amplifier, bus print, bus board, processor card, coupling card, temperature control card -Manufacturer: Siemens, control electronic modules from injection molding machine Demag D 100-275 NC -Interface modules: 6ES5 306-7LA11 -Digital input: 6ES5 430-7LA11 2 pieces -Digital output: 6ES5 454-7LB11 5 pieces -Subrack: 6ES5 701-2LA11 -Individual components: see photos -Price/sale: complete -Total dimensions: 480/210/H305 mm -Weight: 10.8kg

Manual trolley, trolley, crane trolley, trolley drive, crane trolley, trolley, girder trolley, monorail trolley -Crane chassis: Beam width: up to 175 mm -Load capacity: 1000 kg -Dimensions: see technical drawing in the photos -Number: 8x chassis available Price: per piece -Dimensions: 245/200/H190 mm -Weight: 7.6 kg/pc.

Indoor crane, crane, trolley, crane running gear, crane undercarriage, girder undercarriage, headcarriage for bridge cranes, ceiling crane headcarriage, headcarriage single girder bridge crane -Manufacturer: Demag, 1 set of end carriages for single girder bridge crane -Load capacity: 3000 kg -Drive motor: Mannesmann Demag 16I6 KF 8-2 0.15/0.60 Kw -Support rollers: Ø 160 mm / support width 148 mm, dimensions see photos -Dimensions: 2300/650/H570 mm / 300 kg each -Transport dimensions: 2300/1230/H570 mm -Weight: 600 kg/total

Crane remote control, crane control, crane control, pendant control, control switch, control cylinder -Handover: in its current condition as inspected -Housing damaged, cable without connector, see photos -Manufacturer: Demag, crane remote control control unit -Cable length: 2.0 m / 5-core -Dimensions: 500/300/H100 mm -Weight: 1.9 kg

indoor crane, crane, crane runway, crane rails, steel girders, HEB steel girders, double-T-girders, IPB steel girders -Crane runway: for bridge crane, length 2x 9000 mm -Carrier: IPB 320, HEB 320 -Crane rail: flat iron 50 x 30 mm -Dimensions: see photos -Delivery/Price: complete -Weight: 970 kg/piece / 1940 kg total -Transport dimensions: 9130/600/H380 mm -Weight: 1940 kg/total

Indoor crane, crane, crane runway, crane rails, steel girders, HEB steel girders, double-T girders, IPB steel girders -Steel beams: for bridge crane, length 2x 13400 mm / 2x 11000 mm / 2x 7970 mm -Carrier: IPB 340, HEB 340 -Crane rail: flat iron 50 x 30 mm -Dimensions: see photos -Shipping/Price: in pairs or complete -Weight: 1650/1360/950 kg/pc. / 7920 kg total

indoor crane, crane, crane runway, crane rails, steel girders, HEB steel girders, double-T-girders, IPB steel girders -Crane runway: for bridge crane, length 2x 13400 mm / 2x 7980 mm -Carrier: IPB 280, HEB 280 -Crane rail: flat iron 50 x 30 mm -Dimensions: see photos -Distribution/Price: in pairs or complete -Weight: 1270/720 kg/piece / 3980 kg total

Screw compressor, compressor, compressed air unit, stationary compressed air compressor -Manufacturer: Demag / CompAir, screw compressor type 350WS / EK285NK without drive motor -Volume flow: 35.1 m³/min -Max. pressure: 7 bar -Drive shaft: Ø 90 x 120 mm -Individual components: see photos -Dimensions: 1100/670/H1000 mm -Weight: 1032 kg

CPU module, electronic modules, PLC module, plug-in card circuit board, circuit board, board, digital input module, -Printed circuit board: Electronic module from screw compressor Demag type 350WS -Type designations: CPU-MK1 V1.1 MK1-ADU V1.1 MK1 Digital-Input V1.1 MK1 REMIX V1 0205 00111 -Dimensions: 270/170/H130 mm -Weight: 2.6 kg

Gear motor, electric motor, stop motor, drive motor, crane motor, bridge crane -Manufacturer-Motor DEMAG Type: ZBF80A8/2B020 -Manufacturer gearbox DEMAG Type: AMK20DD -Power: 0.13/0.50 kW -Speed: 45/131 rpm -Design: M0-30-1/16.4 -Hollow shaft diameter: toothed Ø 28/30 mm -Protection class: IP54 -Dimensions: 505/210/H220 mm -Weight: 42.3 kg

Gear motor, electric motor, stop motor, drive motor, crane motor, bridge crane -Manufacturer-Motor DEMAG Type: KBF80A8/2 -Manufacturer-Gearbox DEMAG Type: AF04-M-0-1-25-1 -Power: 0.13/0.50 kW -Speed: 43.4/186.8 rpm -Design: hollow shaft -Hollow shaft diameter: toothed Ø 22/25 mm -Protection class: IP54 -Dimensions: 445/155/H270 mm -Weight: 22.4 kg

Electric motor, three-phase motor for gear motor, electric motor, stop motor, drive motor, crane motor, bridge crane -Manufacturer: Demag, crane motor type KMF80A8/2 -Power: 0.13/0.5 kW -Speed: 630/2710 rpm -Shaft: Ø 15.4 mm toothed -Design: B14 -Protection class: IP 54 -Dimensions: 390/156/H225 mm -Weight 17 kg

Friction wheel, running wheel for bridge crane, overhead crane, indoor crane, assembly crane, workstation crane, wheel block, wheel block system, wheel block system -Manufacturer: Demag, wheel block for crane trolley -Type: unfortunately no exact type designation -Wheel: Rail width intermediate dimension 52 mm -Hole: Ø 30 mm, dimensions see photos -Quantity: 1 piece available -Dimensions: 220/123/H160 mm -Weight: 9 kg

Friction wheel, running wheel for bridge crane, overhead crane, indoor crane, assembly crane, workstation crane, wheel block, wheel block system, wheel block system -Manufacturer: Demag, wheel block for crane trolley -Type: unfortunately no exact type designation -Wheel: Rail width intermediate dimension 60 mm -Hole: Ø 30 mm, dimensions see photos -Quantity: 2x wheel block available -Price: per piece -Dimensions: 220/97/H160 mm -Weight: 8.7 kg/piece

Friction wheel, running wheel for bridge crane, bridge crane, overhead crane, assembly crane, workstation crane, wheel block, wheel block system, wheel block system -Manufacturer: Demag, Wheel block for crane chassis -Type: unfortunately no exact type designation -Wheel: Rail width intermediate dimension 48 mm -Hole: Ø 30 mm, dimensions see photos -Quantity: 2 pieces available -Price: per piece -Dimensions: 220/97/H160 mm -Weight: 8.5 kg/pc.

Friction wheel, running wheel for bridge crane, overhead crane, indoor crane, assembly crane, workstation crane, wheel block, wheel block system, wheel block system -Manufacturer: Demag, wheel block for crane trolley -Type: unfortunately no exact type designation -Wheel: Ø 122 mm / rail width intermediate dimension 63 mm -Hole: Ø 30 mm, dimensions see photos -Quantity: 1x wheel block available -Dimensions: 220/97/H160 mm -Weight: 8.5 kg

Electric motor, three-phase motor for gear motor, electric motor, stop motor, drive motor, crane motor, bridge crane -Manufacturer: Demag, crane motor unfortunately without type designation -Power: kW -Speed: 1485 rpm -Shaft: Ø 24 x025 mm -Design: B14 -Dimensions: 370/180/H250 mm -Weight 19.8 kg

Bridge crane, indoor crane, disc brake, crane brake, disc, drum and storm brakes, overhead crane brake, brake ring, conical brake disc, conical brake disc, conical brake ring -Manufacturer: Demag, conical brake disc conical brake ring -Type: 089 762 84 -Mounting: Shaft Ø 46/50 mm -Bolt circle: Ø 70 mm M10 -Dimensions: see photos -Number: 2x brake disc available -Price: per piece -Dimensions: Ø 288 x 90 mm -Weight: 6.3 kg/piece

Double girder traveling crane, bridge crane, overhead crane, assembly crane, workstation crane, ceiling-mounted traveling crane, traveling crane, crane system -with 2x electric cable winches -Load capacity: 2 x 1600 kg -Bridge load capacity: 3.2 tons -Wingspan: 6.4 m -Hallway service -Dimensions: 2000/6400/H1000 mm -Weight: approx. 2000 kg

Demag 1000kg 13/3PF4, Electr. Trolley + C Rail Cable Cable Trolley Chain Hoist Total weight approx. 80 to 120 kg. Good used condition, full function. The cover caps on the hand control unit are missing. Ride back and forth at one speed each. Lifting and lowering at two speeds each. There are 3 C rails with associated connectors. Total length approx. 14m. Including flat cables and sufficient cable trolleys that run in the C rails. Except for the H-beam, the system is then complete.

Key data: 600 kN, 94 g/PS, 30 mm

Clamping force: 60t Year of Make: 2001 Injection weight in hp: 94g Injection Unit .../200 Screw diameter 30 mm Spec. Spray pressure 1995 bar Injection volume 106 cc Injection weight in hp 94 g L/D Screw Ratio 20 Clamping unit 600/... Clamping force 60 t Size of the clamping plates 600 x 600 mm Lights spar spacing 420 x 420 mm Tool installation height 200 mm Opening way 550 mm Max. panel spacing 750 mm Weight 3950 kg Dimensions(m) LxWxH 4.2 x 1.4 x 2.0 m Year of construction 2001 Control type NC4

Key data: 600 kN, 94 g/PS, 30 mm

Clamping force: 60t Year of Make: 2001 Injection weight in hp: 94g Injection Unit .../200 Screw diameter 30 mm Spec. Spray pressure 1995 bar Injection volume 106 cc Injection weight in hp 94 g L/D Screw Ratio 20 Clamping unit 600/... Clamping force 60 t Size of the clamping plates 600 x 600 mm Lights spar spacing 420 x 420 mm Tool installation height 200 mm Opening way 550 mm Max. panel spacing 750 mm Weight 3950 kg Dimensions(m) LxWxH 4.2 x 1.4 x 2.0 m Year of construction 2001 Control type NC4

Overhead crane, crane, trolley, crane running gear, crane trolley, girder trolley, head girder for bridge cranes, ceiling crane head girder, head girder single girder bridge crane -Manufacturer: Demag, 1 set of end girders for single girder bridge crane -Type: ELV -Load capacity: kg -Carrying rollers: Ø 160 mm -Hole spacing: 290 mm Ø 20 mm / Dimensions see photos -Transport dimensions: 2355/365/H245 mm -Weight: 302 kg

Additional title: Slewing crane, Maximum load: 2000 kg, Reach: 4 m , Lifting height: 3 m, Length: 4,00 m, Height: 4,61 m

B&A REF:  9314 TON: 420 SCREW DIAMETER:  70MM SHOT WEIGHT:  1090 STROKE VOLUME:  1212CM3 INJECTION PRESSURE:  1877AR PLATEN SIZES:  1200 X 1100MM DBTB: 810 X 710MM MIN MOULD HEIGHT:  380MM MAX MOULD HEIGHT: 820MM MOULD OPENING STROKE:  710MM MAX DAYLIGHT:  1530MM EJECTOR STROKE:  230MM CONTROLS:  NC4 CORE PULLING: 2 AIR VALVES: 3 MOTOR: 45 HEATING CAPACITY: 27KW ROBOT INTERFACE: EUROMAP SCREW DRIVE:   HYDRAULIC

Dominioni Punto & Pasta Pasta extruder machine Stainless 8Kg hopper with agitator and stainless screw, variable speed, variety of extrusion plates for different style pastas, mobile

The electricity and gas-powered plant enables surface treatment of plastic films by flames. Field of application: Z.B. reverse films in the solar industry
 COMPONENTS • PSA Reversible Unwinding and Reversible Winder 2200/12 PSA W/ARW 2200/12 – Fyling Splice • Hill/ Jungwirth burner unit for gas/air mixture • Suction • Erhardt+ Leimer web edge control • OCS camera system for error detection • Semket labelling system for marking defects • GWK temperature control units for roller cooling SKL SP HC300 330KW

General SKU345S761 LocationBarneveld MakeUnex Heatexchanger GmbH (DE) TypeHybrid No.HB 25228400028 Year of construction2000 Pressure Working pressure6 Bar Vacuum possiblecheck Main Features MaterialStainless steel Surface5.7 m2 Specified Features - Plate heat exchanger MaterialStainless steel 1.4571 (316Ti) Plate heat exchangerscheck Number of stages:1 Heating surface5,7 m2 Capacity42 Ltr ConnectionsDN80(2x), DN 50(2x) Max. temperature-30/200°C. Information Floorspace1,0x0,7 M Total height1,0 M Weight260 KG Extra SpecificationsCondenser Plate heat exchangersUnexHeat exchangers > Plate heat exchangersBrand > Unex What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barne ...

General SKU345S754 LocationBarneveld MakeUnex Heatexchanger GmbH TypeHybrid No.HB 25228400034 Year of construction2000 Pressure Working pressure6 Bar Vacuum possiblecheck Main Features MaterialStainless steel Surface5.7 m2 Specified Features - Plate heat exchanger MaterialStainless steel 1.4571 (316Ti) Plate heat exchangersHybrid Number of stages:1 Heating surface5.7 Capacity42 Ltr ConnectionsDN50(2x), DN100, DN40, DN80(2x) Max. temperature-30/200°C. Information Floorspace0,9x Total height1,0 M Weight260 KG Extra SpecificationsCondenser Plate heat exchangersUnexHeat exchangers > Plate heat exchangersBrand > Unex What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barne ...

General SKU345S1121 LocationBarneveld MakeUnex TypeKondensator No.HB25228400032 Year of construction2000 Pressure Working pressure6 Bar Vacuum possiblecheck Main Features MaterialStainless steel Surface5.7 m2 Specified Features - Plate heat exchanger MaterialStainless steel 1.4571 (316Ti) Plate heat exchangerscheck Heating surface5.7 m2 Capacity42 Ltr. ConnectionsDN80 (2x), DN50 (2x) Max. temperature-30/200 °C Information Total height0,7 m Weight260 Kg Floorspace0,9x1 m Extra SpecificationsCondenser Plate heat exchangersUnexHeat exchangers > Plate heat exchangersBrand > Unex What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

General SKU345S814 LocationBarneveld MakeUnex Heatexchanger GmbH TypeHybrid No.HB 25228400033 Year of construction2000 Pressure Working pressure6 Bar Vacuum possiblecheck Main Features MaterialStainless steel Surface5.7 m2 Specified Features - Plate heat exchanger MaterialStainless steel 1.4571 (316Ti) Plate heat exchangerscheck Number of stages:1 Heating surface5,7m2 Capacity42 Ltr ConnectionsDN100, dn80(2X), DN50, DN40 Max. temperature-30/200°C. Information Floorspace0,9 x 0,7 M Total height1,0 M Weight260 KG Extra SpecificationsCondenser Plate heat exchangersUnexHeat exchangers > Plate heat exchangersBrand > Unex What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in B ...

General SKU345S784 LocationBarneveld MakeUnex Heatexchanger GmbH TypeHybrid No.HB 25228400035 Year of construction2000 Pressure Working pressure6 Bar Vacuum possiblecheck Main Features MaterialStainless steel Surface12 m2 Size length1200 mm Sizes width1100 mm Specified Features - Plate heat exchanger MaterialStainless steel 1.4571 (316Ti) Plate heat exchangersfully welden plate heat exchanger Heating surface12 m² Capacity111 Ltr., 57 Ltr. (shell) ConnectionsProduct: (2x)DN80, DN40: Plates: DN150, DN80 Max. temperature-30/200 °C Information Floorspace1,2 x 1,1 m Total height0,8 m Weight490 kg Extra Specificationssuitable for use as a condenser Plate heat exchangersUnexHeat exchangers > Plate heat exchangersBrand > Unex What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destinati ...

General SKU345S770 LocationBarneveld MakeUnex Heatexchanger GmbH TypeHybrid No.HB 25228400030 Year of construction2000 Pressure Working pressure6 Bar Vacuum possiblecheck Main Features MaterialStainless steel Surface5.7 m2 Specified Features - Plate heat exchanger MaterialStainless steel 1.4571 (316Ti) Plate heat exchangerscheck Number of stages:1 Heating surface5,7 M2 Capacity42 Ltr Connections(2x) DN50,(2x) DN80 Max. temperature-30/200°C. Information Floorspace0,9x0,7 M Total height1,0 M Weight260 KG Extra SpecificationsCondenser Plate heat exchangersUnexHeat exchangers > Plate heat exchangersBrand > Unex What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld  ...

General SKU329T1340 LocationBarneveld MakeDec TypeDrum sealing cover No.DSC-130 Year of construction2016 Main Features MaterialStainless steel Number of1 heads Specified Features - Powder filler MaterialGlass, Stainless steel 1.4435 (316L) Information Mounted in framecheck Total height2,9 m Weight400 kg CEcheck Floorspace0,79x1,32 m ATEX compatiblecheck Extra SpecificationsWith powderbox, Dia:500x200mm lifting column stroke 320mm balancer cap. 7,5-11,5 kg suction lance DN40 triclamp x approx 1500mm cip connection Stäubli R 1/4” hub 2000mm, Magnehelic box Bizerba weighing scale, type ST-D-Z2, (Ex) Dec powder transfer system, type PTS 80-N cap. 500l/h temp range max 100°C pressure -50/+50 PED class Gas 2/ Art. 3.3, consumption 5 Nm3/h (stickstoff) at 3 bar, product input DN 32 Triclamp, product output DN80 PN10, pneumatic control, dim. 600x380x210 mm, roll conveyor, ...

General SKU330W1522 LocationBarneveld MakeAro Type650-607 Mach.No.90’ 1747 Pressure Working pressure10 Bar Main Features MaterialStainless steel Specified Features - Centrifugal Pump MaterialStainless steel Centrifugal Pumps Pumpcheck Number of pumps:1 Pneumatic drivecheck Outletdia. 25 mm Information Year of construction1990 Mounted on wheelscheck With switchcheck Floorspace1,30x0,63 m Total height1,80 m Weight300 kg Extra SpecificationsDrum air pressure pump, Festo pressure cabinetCentrifugal PumpsAroPumps > Centrifugal PumpsBrand > Aro What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

General SKU330W1524 LocationBarneveld MakeAro Type650-607 Mach.No.15’1064 Pressure Working pressure10 Bar Main Features MaterialStainless steel Specified Features - Centrifugal Pump MaterialStainless steel Centrifugal Pumps Pumpcheck Number of pumps:1 Pneumatic drivecheck OutletDia. 25 mm Information Year of construction2015 Mounted on wheelscheck With switchcheck Floorspace1,30x0,63 m Total height1,80 m Weight300 kg Extra SpecificationsDrum air pressure pump, Festo pressure cabinetCentrifugal PumpsAroPumps > Centrifugal PumpsBrand > Aro What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

General SKU345S769 MakeUnex Heatechager GmbH TypeHybrid No.HB 25228400038 Year of construction2001 LocationBarneveld Pressure Working pressure6 Bar Vacuum possiblecheck Main Features MaterialStainless steel Surface22 m2 Specified Features - Plate heat exchanger MaterialStainless steel 1.4571 (316Ti) Plate heat exchangerscheck Number of stages:1 Heating surface22m2 Capacity166 Ltr ConnectionsDN150. DN80(4X) Max. temperature-30/200 degr.C. Information Floorspace1,5x0,8 M Total height1,2 M Weight560 KGPlate heat exchangersUnexHeat exchangers > Plate heat exchangersBrand > Unex What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

General SKU345S756 MakeUnex Heatexchanger GmbH TypeHybrid No.HB 25228400036 Year of construction2000 LocationBarneveld Pressure Working pressure6 Bar Vacuum possiblecheck Main Features MaterialStainless steel Surface12 m2 Specified Features - Plate heat exchanger MaterialStainless steel 1.4571 (316Ti) Plate heat exchangerscheck Number of stages:1 Heating surface12m² Capacity111 Ltr. ConnectionsDN100, DN80(2x), DN40,DN150, DN80 Max. temperature-30/200°C. Information Floorspace1,2x0,8 M Total height1,1 M Weight490 KG Extra SpecificationsCondenserPlate heat exchangersUnexHeat exchangers > Plate heat exchangersBrand > Unex What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us  ...