129,238 used machines on RESALE, but how to find them? Machine Search
Packaging machine PEWO - pack 450 SN with shrink tunnel Plant for stripping and packing products in boxes. The boxes are then wrapped in foil in the shrink tunnel. Very good ready-to-use condition, directly from production!
; Gross weight [kg]: 4667; Engine: Perkins 2206A-E13TAG3; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 888
MARINE GEARBOX Reference number 20106 Brand Gearbox REINTJES Model Gearbox WLS 430 U Ratio 2,458:1 Power 825 KW RPM 1745 RPM Serial number 56384 General condition TAKEN OUT RUNNING EX MILITARY FAST CRAFT Status AVAILABLE SPECIFIC INFORMATION Sae housing 30 Flexible coupling Controls YES - INCLUDING CABLES AND ELETRONIC ACTUATOR Brackets YES Oil cooler YES Weight (kg) 590 KG
; Power [PS]: 489; Gross weight [kg]: 3840; Engine: Cummins QSG12-G4; Accessories: Tanker, Battery, Control Panel, Stahldach, Incl. Coolant Heater and Battery Charger; Water Tank Volume [l]: 995
The PEWOPACK 450 is an electronically/pneumatically controlled tightening barrier insulating machine for the production of single and multi-piece containers. It pops up the products in boxes and welds them into a thermal foil. Power max:60 boxes/min Slide type: PE Ptsegq Film width 50 - 450 mm Film thickness 0.025-0.100 mm Roll diameter max. 300 mm
Robust, high-quality beading and flanging machine with electric motor drive, optionally available with hydraulic bending roller delivery - optionally available with circular cutting device Largest sheet thickness, which is malleable - 3 mm steel sheet/ST40, maximum extension 450 mm, maximum distance between the top and lower roller 100 mm, two working speeds 6 and 33 rpm - available at additional cost with infinitely adjustable working speed and frequency converter, Time relay for limiting the working cycle, possible round diameter when using the circular cutting device between 300 mm and 1,200 mm (optional up to 1,620 mm), cutting power with the shear blades 3 mm steel sheet/ST40, drive power 1.8 kW – drive power hydraulics 1.5 kW, weight of the base machine 570 kg
Shrink Tunnel Kallfass Standard 450 N; State as is; checked only for function; Inlet width 400mm; Pass-through height 200mm; Cooling fan. Shrink tunnel Kallfass Standard 450 N; condition as is; only chekced on function; width 400mm; hight 200mm; cooling unit.
Slicer WABÄMA: knives thickness 9 mm, new knives; power 0.5 kW/380V semi-automatic lubrication; automatic adjustment of the height at the upper plate of bread;
Max blade diameter: 450 mm Weight: approx. 700 kg Hydropneumatic saw blade feed via 2 manual operation Pneumatic material tensioners Minimum quantity spraying device Table rotatable on both sides with rest points at 45°
Oven 450 inner dimensions 2x2x6m PLC Uterna / Europe custom made oven Schachtofen Haubenofen Rollenherdöfen Durchstoßöfen Härten Glühen Normalisieren Weichglühen Vergüten Anlassen Entspannen Durchschuböfen Hubbalkenöfen Hubherdöfen Trockenöfen Rollenherdöfen Drehherdöfen Kammeröfen Mehrkammeröfen Verfahrbare Haubenöfen Herdwagenöfen Kammeröfen Haubenöfen Drehherdöfen Thermische Nachverbrennungsanlagen forno a camera per trattamento termico alluminio forno a carro per trattamento termico alluminioforno a carro per trattamento termico alluminio forno a carro per trattamento termico alluminio forno continuo per trattamento termico alluminioforno continuo per trattamento termico alluminio forno continuo per trattamento termico alluminio linea batch per trattamento termico alluminiolinea batch per trattamento termico aliuminio forni industriali da ...
Machine type MIG/MAG welding system Make MERKLE Type OptiMIG 451 KW Connection voltage 3 x 400 volts Adjustment range 25 - 450 amperes Switch-on time 40% ED at 450 amperes 60% ED at 420 amperes 100% ED at 340 amperes Current setting 42 switching stages Cooling transformer due to built-in fan Cooling burner water-cooled Execution of mobile industrial plant Wire feed gearbox 4-wheel transmission DV 26 Fuse 32 Ampere Dimensions L x W x H 990 x 510 x 845 mm Weight 200 kg Special accessories Volt and Ampere digital display Automatic wire Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch 3 mtr. long 1 piece ground cable 4 mtr. long, 70 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 piece spare part box ...
Cutting length mm: 4500. Cutting depth mm: 4500 Number of pliers: 7 Installed power KW: 15 Diameter saw blade mm: 300 Vorritzer: Yes Discharge tables pneumatic: 3 Weight Kg: 3100 CE marking
M. No.: 3284 Equipment / Additional information: (min.) material thickness: 0.65 mm (max.) material thickness: 2 mm Technical Data: Width of film, max./min. 450/350 mm Forming area max. 430 x 160 mm Drawing depth max. negative/positive 6/20 mm (on request 22 mm negative) Top heater max. 10,15 kW Driving motors 3,0 kW Total connected load at 100 % duty cycle 12,7 kW Working air pressure 6 bar Air consumption (dependent on product) max. 1250 I/min Rate of water flow max. 1,0 m3/h COMPACT AND ROBUST - giving continuous high output. Easy and ergonomical operation (e.g. take- off height 1300 mm). QUICKLY CHANGEOVER - from 30° to 90° foil feed giving maximum material utilisation for both square and round lids. Heater changeover problem-free. PRECISION - The accuracy of the form table movement is guaranteed by linear guide bearings and hardened rods. The safe ...
Machine details Bearing number 1105-03282 Machine type Machining Center - Vertical Make FAMUP Type MCX 450 Built in 1997 Control type CNC Control FANUC OMC Warehouse FRANCE Country of origin Italy Delivery time immediately Freight base EX WORK Technical details x-path 450 mm y-path 300 mm z-way 400 mm Control FANUC OMC Spindle speed 8000 rpm Spindle motor 5 kW Rapids x/y/z 30 mm/min Table size 600 x 300 mm Tool change time 0.9 sec Tool magazine: 16 FACH SK 30 Information WITH CONTROL FANUC OMC 8000 RPM 5 KW 2.5 TONS MASSE 2 X 2.25 X 2.3 16 FACH MAGAZIN SK 30
closing pressure: 4360 kN table-size: 730 x 730 mm control: B+R Industrieelektronik draw back pressure: 190 kN ajustment speed: max. 60 mm/sec return speed: max. 90 mm/sec daylight between the columns: 900 mm = vulcanizing press with vertical closing unit, with form removal and form separation device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 1000 mm table width: 1000 mm table load: 1,5 t flange diameter: 700 mm turning speed: max. 0,04 U/min weight of the machine ca.: 1,2 t dimensions of machine L x W x H: 1,60 x 2,0 x 1,50 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 450 mm y-travel: 400 mm z-travel: 320 mm tool taper: HSK 63 spindle turning speed range: 0 - 10000 U/min rapid traverse: 30 m/min System for processing fittings, valve housings, etc. consisting of 1 used flexible manufacturing cell (transfer machine) make RIELLO, model VERTIFLEX VFX 450-2 / 1-0 / 1-V, YOM 2010, with 2 pcs. 3-axis machining modules, each with 8-pos. tool turret, travel paths module 1: X1 / Y1 / Z1 = 450/400/320 mm, travel paths module 2: X2 / Y2 / Z2 = 450/400/320 mm, tool fixture HSK 63, rotary table with 2 integrated workpiece carriers á 400 mmø (B axis per workpiece carrier 360 x 1 °), coolant through spindle Acc.: chip conveyor, coolant device connected by ABB handling robot with 1 used flexible manufacturing cell (transfer machine) make RIELLO, model VERTIFLEX VFX 450-2 / 2-0 / 1-V, YOM 2003, with 3 pcs. 3-axis machining modules, each with 8-po ...
spindle diameter: 105 mm x-travel: 1200 mm y-travel: 1000 mm z-travel: 325 mm adjustment of cross-rail: 785 mm distance between columns: 1600 mm distance spindle - column min./max.: 215 / 1100 mm spindle feeds - stepless: 1 - 6000 mm/min spindle taper: ISO 40 spindle turning speed - stepless: 40 - 1800 U/min table surface area: 900 x 1500 mm workpiece weight: 2000 kg spindle drive: 5 kW total power requirement: KVA weight of the machine ca.: 6 t dimensions of the machine ca.: 3,3 x 3,0 x 2,8 m dimensions of the machine ca.: 3,3 x 3,0 x 2,9 m • with RENISHAW -detector OMP 40, • mechanical refurbishing and new control HEIDENHAIN TNC 410 in year 2002 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
capacity 90 degrees: round: 350 mm capacity 90 degrees: square: 330 mm : 450x320 saw band length: 4250x34x1,1 mm band speed: 40 + 80 m/min table height: 845 mm saw band width: 34 mm total power requirement: 2,2 kW weight of the machine ca.: 0,985 t dimensions of the machine ca.: 1,4 x 2,0 x 2,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 1140 °C
Continious Brazing/Sintering furnace manufactured by Mahler. Type: Humpback (lower H2 consumption). Belt width: 450mm Clearance above belt: 200 mm Heating length: 5000mm Gross throughput: 600 kg/h Electric heating power: 198 kW Service temperature: 1140 Adjustable range of belt speed: 100-1000 mm/min Temperature cotroul groups: 5x Total length: 30m width: 1,8m height: 2,8m Hydrogen connection: 0,1bar 30Nm3/h (type 3.0) Nitrogen connection: 0,1 bar 60 Nm3/h (type 5.0) Exhaust gas : 300 m3/h Furnace is in use, and was regularly serviced. In 12. 2024 brick lining, heating elements, thermocouples, mesh belt and muffle was replaced . Spare parts are available, in case of interest, can be subject of seperate agreement. Offer includes: - Water cooling system with glicol base heat exchanger - Exhaust tubes (2x around 5m Stainless steel) - 5x sensor system to detect ex ...
We can offer a Krauss Maffei injection moulding machine, manufactured in 2017, short time working, like new one, serious buyer contact us. We have many brands, models,years machines, tell me what you need seriously!
The new powerful dry-running pumps: The ADH series is specially designed for solar developed for the demanding processes of the semiconductor and LED markets, With a suction capacity of 600-4500 m3/h. Semiconductors: High H2 pumping rate The performance of the ADH series brings the following advantages to the process: -ADL process performance: high pumping efficiency of light gases enables faster chamber emptying between process steps - Epitaxy and EUV: high pumping speed and high flow rate Tolerance meets the most demanding process specifications Adixen AD30K dry pump, high vacuum, AD 30 KL Manufacturer: Alcatel Adixen Type: AD30K.H Year of manufacture: 2008 Adixen AD100K.H Manufacturer: Alcatel Adixen Type: AD100K.H Year of manufacture: 2008 Vacuum pump: Manufacturer: AERZEN Type: GM 2000 CM-C Speed: 6000 rpm Voltage: 200-460 V Frequency (mineral oil/PFPE ...
Mechanized table. Sizes: 4500x1220x360mm. Screws for levelling. T slots of 60x35mm. Posibility of sell with a sliding radial drill.
High-quality PLC – controlled automatic 90° under-table – straight-cut circular saw machine, for the rational cutting of profiles made of aluminium – non-ferrous metals – plastics – wood and other soft materials Smallest possible section length 5 mm Largest stroke of the feed clamping stick 620 mm (feed length unlimited) Infinitely adjustable feed speed Feed accuracy +/- 0.2 mm Horizontal and vertical material tension Largest saw blade diameter 450 mm Cutting area - - 300 mm x H 50 mm - 260 mm x H 98 mm - 240 mm x H 100 mm (see the figure with the section diagram) Saw blade speed 2,800 rpm Saw blade drive power 2.2 kW Dimensions approx. 1.5 x 0.9 m x H 1.36 m Weight approx. 440 kg
KOTEC PSD-4520 CNC drilling machine was built in 2020 in South Korea by KOTEC Co., Ltd. The machine, which is designed for drilling precision holes and threading, is an excellent choice for companies specialising in, among others, the construction of machinery or the production of steel structures. The machining process is performed in three axes (X,Y,Z) on a large work area with a length of 4500 mm and a width of 2000 mm. A number of state-of-the-art components, combined with an extremely stable design, guarantee the best results, even during the most intensive machining. All this is complemented by an advanced CNC control with an intuitive interface and all the necessary functions. The KOTEC PSD 4520 CNC beam drilling machine weighs approximately 8900 kg. Technical specifications of the KOTEC PSD-4520 CNC metal drilling machine - number of axes: 3 (X,Y,Z) - feed in the X/Y axis: 4 ...
Toyota, Forklift Diesel BJ 2018 Toyota 40-8FD40N , 4.5 to / 4500 kg Payload 1.Hand, bought from us New, available now just look at it on site Full view duplex mast 4000mm, with lateral shift and fork positioner, Manufacturer Meyer, forks/tine length 1200mm approx. 11,500 BH / operating hours, 408FD40N10563 Year of manufacture 2018 Comfort cab, heating Mini lever for quick and easy operation, Switch on the left of the steering column for changing direction of travel On-board computer including load weight display Comfortable Grammer seat wide fenders and 300mm wide pneumatic tires also suitable Price VHB Diesel forklift type 40-8FD40N with SAS system for active stability Basic load capacity 4500 kg Load center 500 mm Mast type full clearance duplex Lifting height approx. 4000 mm Overall height approx. 2990 mm Free ...
Operating hours: 600h Specifications: Travel in X/Y/Z: 450 / 350 / 400 mm Distance from spindle nose table: 230 - 630 mm (horizontal milling spindle) Rapid traverse speed X/Y/Z: 5000 / 5000 / 5000 mm/min Working feed X/Y/Z: 10 - 2000 mm/min infinitely variable Max. feed force in X/Y/Z: 10 / 10 / 15 kN Clamping surface: 800 x 400 mm (rigid angle table) Max. table load: 30 kg (rigid angle table) Vertical milling head: Speed range: 10 - 5000 1/min Power: 10 kW Dimensions (LxWxH), approx.: 1980 x 2030 x 1990 mm Weight, approx.: 2270kg Equipment: - Swivel control panel - Shafts and gears hardened and ground - Digital display Sinumerik 828D - Clockwise / counterclockwise rotation of the main spindle - Linear guides - Four-bearing milling spindle radial/axial - All pinch points eliminated by covers - Main motor with spindle brake
; Gross weight [kg]: 4667; Engine: Caterpillar C13; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 842
; Gross weight [kg]: 3754; Engine: Caterpillar C13; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger, Including : Caterpillar PL444 cellular radio system; Water Tank Volume [l]: 721
Used Grasso FKS PP 450/S water cooled chiller on Ammonia (R717). Complete with 1 Grasso HR-H36S-28 screw compressor, 2EC IE4-0DP-250M2 electric motor - 50 Hz - 110 kW - 2970 RPM, brazed heat exchanger as evaporator, brazed heat exchanger as condenser, Grasso oil separator with a volume of 275 liter, oil cooler, oil pump and a control cabinet with a Siemens Simatic HMI controller. Capacity based on a cold water inlet/outlet of 12°C/6°C and a cooling water temperatures of 27°C/32°C. Specifications: Brand: Grasso Type: FKS PP 450/S Product type: Water cooled chiller Capacity kW: 445,0 (cold water inlet/outlet of 12°C/6°C and cooling water temperatures of 27°C/32°C) Capacity tons: 126,5 (cold water inlet/outlet of 12°C/6°C and cooling water temperatures of 27°C/32°C) Refrigerant: R717 Weight in kg: 5200 Sizes: 3400x1900x2400 mm (LxWxH) Compressors: Grasso HMR-H36S-28 ...
; Gross weight [kg]: 13000; Engine: DC13 072A/02-12; Accessories: Tanker, Battery, Control Panel, Stahldach, -Super Silent Canopy; Water Tank Volume [l]: 2500
used
Dimensions (L/W/H): 3940x850x1350 mm Weight: 410 kg Total power requirement: 5,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 0x0x0 mm Weight: 300 kg Total power requirement: 0,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 0x0x0 mm Weight: 900 kg Total power requirement: 5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
Boring power: 35 mm turning speeds: max. 810 U/min core drilling diameter max.: 35 mm tool taper: Weldon 19,05 mm bore stroke: 210 mm weight: 11 kg connected load frequency: 230 V engine output: 1,6 kW Dimensions (LxWxH): 0,4 x 0,25 x 0,275 m Magnetic drill with: 2-speed motor. Coolant system. Robust mobile storage / carrying bag. MAGNET HOLDING FORCE 1800 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Electrode welding machine Manufacturer Kemppi Type TYLARC453 Power 450 amps at 35% ED, 345 amps at 60% ED 265 amps at 100% ED Power 20kw, 21kva Power connection 400 Volt Weight approx. 250kg Machine ready for demonstration under power. Shipping on Euro pallet possible. Price is net plus 19% VAT Please note our "Legal Information" with further information
Kaltenbach circular saw KKS 450 with length measuring system L-40NC Specifications Type: Kaltenbach Length measuring system: L-40NC Year of construction: 2005 Type circular saw: KKS 450 H Year of construction: 1998 Saw blade: Ø 450mm / holder Ø50mm Working range max (90°) 150mm Working range square (90°) 140x140mm Working range flat steel (90°) 330x40mm Working range U-steel standing (90°) 120x55mm Working range round (90°) Ø 150mm Miter range 0° - 90° 0° Dimensions: LxWxH 1110x1020x2000mm Weight: approx. 950kg Description: Used, hydraulic universal saw machine in semi-automatic design with rotary table for miter cuts: - Clamping, sawing, returning, opening – simply at the push of a button - Adjustment of the cutting height via push buttons - User-friendly electronic control directly on the machine - Good accessibility for saw blade changes and ...
Type: MIX MAXI Mix volume: 450 liters Two mixing shafts with paddles Stepless speed regulation Programmable operation One outlet, mechanically operated Protective cover of hopper Lifting device for standard trolley 200 l Machine dimensions in сm: Width: 100,0 (190,00 with lifting device) Length: 180,0 Height: 220,0 Power: 5,5 kW Voltage: 380 V, 50Hz
We offer Doka Eurex 30 top 450 Original Doka rental storage quality. Supports cleaned and checked. Doka Eurex 30 top 450, used - 64,90€/piece Doka Stacking Pallet 1.55m x 0.85m, used = 115.00€/piece The extra-durable ceiling support with impact protector The robust and durable Eurex 30 top slab prop impresses with a high minimum load capacity of 30 kN and complies with column class C/E according to the EN 1065 standard. The integrated impact protector reliably protects the stud tube from mechanical damage and significantly increases the service life of the steel tube support. If you have any questions, please call 0049 176 70044689 Mr. Becker Offer only valid while stocks last. Subject to prior sale. Purchase and sale of scaffolding/formwork systems and construction machinery; Formwork restoration at fair conditions. Company SFS Meisterbetrieb Andreas Beck ...
Brotschneidemaschine verwendet. Sehr guter Zustand.
Laminator Peak PP-450 HR; good condition; cleaned and tested; Working width 450mm; .max. Strength 350mic.; temperature range 100-160 C'; Speed 650mm/min.; Table unit. Laminating machine Peak PP-450 HR; good condition; cleaned and checked; working width 450mm; max.thikness 350mic.; temperature 100-160C'; Speed 650mm/min.; table top machine.
maximum number of results exceeded
please refine your search
