deckel 80 u used for sale

x-travel:560 mm y-travel:500 mm z-travel:450 mm

x-travel: 500 mm y-travel: 450 mm z-travel: 400 mm Control: HEIDENHAIN iTNC 530 Table dimensions: 500 x 380 mm table weight: 500 Kg c-axis: 0.001º ( ± 360º) 0 b-axis: 180 ° rapid traverse X-axis: 80 m/min feeds: 50 m/min spindle turning speed range: 18.000 U/min spindle taper: BT- 40 spindle drive: 30 kW Internal cooling system: 40 bar handwheel: HEIDENHAIN HR-410 total power requirement: 50 kVA weight of the machine ca.: 6,5 t dimensions of the machine ca.: m Chip conveyor: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Double Swivel Head Fast Runner SK40 for the Deckel FP Milling Machine without Motor However, the motor of the normal high-speed engine should fit just as well. Although the complete head probably has 70kg at the end, it probably even fits from FP1 upwards to FP4 Very good used condition, either never used, or only a few times. Except for slight traces of storage, no signs of wear to be seen. The spindle rotates cleanly and easily. However, the (drilling) stroke is a bit heavy, probably has to be adjusted. Pickup. However, a delivery can be arranged in advance, can... You will receive an invoice in paper form. Differential taxation according to sec. 25a of the German VAT Act. Therefore, no VAT is shown on the invoice.

Year of manufacture 2001 Heidenhain TNC 310 Travel distances 350 x 240 x 340 Spindle speed 20 - 5000 Drive power 6.3/10 KW Total connected load 15 kW Tool holder SK40 Accessories: el. Handwheel Universal swivel rotary table 400 x 280 mm, Rotation range 360°, swivel range +105/-15° with electronic angle display Coolant Setup

Inv. Num. : 5211 Type: DMU 80 P Producer: Deckel Maho Generated: 2000 Parameters: Control system: Heidenhein TNC 430 Switch-on hours: 87285 h Hours: 34100 h Minimum vertical spindle speed: 20 1/min Maximum vertical spindle speed: 12000 1/min X-axis travel: 800 mm Y-axis travel: 650 mm Z-axis travel: 550 mm Cone: ISO 40 Number of all tools: 30 pieces Equipment: IKZ Workpiece Probe Conveyor Spindle cooling 2020: Replacement of the PILS contactors New E/R module New X/Y Module 2019: Lock Replacement Workpiece Probe Sensor Replacement Replacing the hydraulic hose of the tool clamp 2018: New X/Y axle bolt Replacement of the Y-axis blind Replacement of the B-axis planetary gearbox New motor and B-axis measuring cable 2016: New spindle bearings System Replacement Replacing the UV105 power supply Replacement of the spindle mod ...

DECKEL S11, universal tool & cutter grinder, under power in our warehouse, Mimu machine-tools (Italy)

Key data: 600 mm, 525 mm, 200 mm

Tool Milling Machine - Universal DMU 60 E Machine x-travel: 600 mm y-travel: 525 mm z-travel: 500 mm Serial No.033 Table clamping surface: 1000 x 543 mm Spindle holder: SK 40 Spindle holder: DIN 69871 Spindle speeds - infinitely variable: 20 - 12,000 rpm Feeds X/Y/Z axis: 20 - 10,000 mm/min Rapid traverse X/Y/Z axis: 18 / 18 / 15 m/min Table load: max. 350 kg Control: HEIDENHAIN Head swivel +/-: 90 ° Total power requirement: 26 kVA Machine weight approx.: 4.2 t Machine dimensions L x W x H: 2.95 x 2.1 x 2.26 m Coolant Setup Machine was dismantled Machine is sold as a defect

Key data: 600 mm, 525 mm, 500 mm

Tool Milling Machine - Universal DECKEL-MAHO DMU 60 E Machine x-travel: 600 mm y-travel: 525 mm z-travel: 500 mm Serial no.023 Table clamping surface: 1000 x 543 mm Spindle holder: SK 40 Spindle holder: DIN 69871 Spindle speeds - infinitely variable: 20 - 12,000 rpm Feeds X/Y/Z axis: 20 - 10,000 mm/min Rapid traverse X/Y/Z axis: 18 / 18 / 15 m/min Table load: max. 350 kg Control: HEIDENHAIN Head swivel +/-: 90 ° Total power requirement: 26 kVA Machine weight approx.: 4.2 t Machine dimensions L x W x H: 2.95 x 2.1 x 2.26 m Coolant Setup Machine was dismantled

Key data: 600 mm, 525 mm, 500 mm

Tool Milling Machine - Universal DECKEL-MAHO DMU 60 E Machine x-travel: 600 mm y-travel: 525 mm z-travel: 500 mm Serial.no.063 Table clamping surface: 1000 x 543 mm Spindle holder: SK 40 Spindle holder: DIN 69871 Spindle speeds - infinitely variable: 20 - 12,000 rpm Feeds X/Y/Z axis: 20 - 10,000 mm/min Rapid traverse X/Y/Z axis: 18 / 18 / 15 m/min Table load: max. 350 kg Control: HEIDENHAIN Head swivel +/-: 90 ° Total power requirement: 26 kVA Machine weight approx.: 4.2 t Machine dimensions L x W x H: 2.95 x 2.1 x 2.26 m Coolant Setup Machine was dismantled

Key data: 710 mm, 520 mm, 520 mm

TECHNICAL DETAILS X-axis travel:710 mm Y-axis travel:520 mm Z-axis travel:520 mm Rapid traverse X-axis:30 m/min Y-axis rapid traverse:30 m/min Rapid traverse Z-axis:30 m/min X-axis feed speed:10 m/min Y-axis feed speed:10 m/min Z-axis feed speed:10 m/min Overall height:3,300 mm Overall length:4,600 mm Overall width:5,500 mm Total weight:6,000 kg Spindle speed (min.):20 rpm Spindle speed (max.):12,000 rpm Spindle motor power:25,000 W Input voltage:400 V Type of input current:three-phase Work table length:700 mm Worktable width:500 mm

x-travel: 500 mm y-travel: 300 mm z-travel: 380 mm spindle stroke: 100 mm turning speeds: 40-2000 U/min Table area: 380x800 mm Feed: 10-500 mm/min Feed: 10-500 mm/min Rapid movement: 1500 mm/min spindle taper: ISO: 40 digital readout: Elesta total power requirement: 3 kW weight of the machine ca.: 1,1 t dimensions of the machine ca.: 1,2x1,2x1,7 m The tech. Data are manufacturer or operator information and therefore for us not binding. We reserve the right to prior sale, it apply only our business and conditions of sale. About Us more than 400 own machines in stock over 12000 m² storage area, crane capacity 70 t more than 10000 articles accessories for your workshop You want to sell machines, production lines or your company, Then contact us. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

spindle taper ISO: 40 x-travel: 710 mm y-travel: 600 mm z-travel: 445 mm Control: Heidenhain type: TNC355 mm table surface area: 1000x550 mm turning speeds: 6300 U/min quill stroke: 80 mm Feed: 1-3600 mm/min rapid traverse: 6 m/min total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 400 mm y-travel: 400 mm z-travel: 400 mm control: Grundig Contour tool taper: SK40 total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 1200 mm, 600 mm, 500 mm

Dialog 11 Control Travels 1200 x 600 x 500 Max. spindle speeds 5000/rpm Spindle drive 12 kW Tool holder SK40 Quill stroke 80 mm, weight approx. 7000 kg. Accessories el. Handwheel, coolant device. The machine is in very good condition.

Inv. Num. : 8185 Type: FP 3 NC Producer: Deckel Generated: Parameters: Work table length: 700 mm Work table width: 460 mm Maximum vertical spindle speed: 4000 1/min X-axis travel: 400 mm Y-axis travel: 400 mm Travel Z axis: 340 mm Machine height: 1800 mm Machine length: 2000 mm Machine width: 1400 mm Machine weight: 1900 kg

x-travel: 500 mm y-travel: 400 mm z-travel: 400 mm Control: Heidenhain TNC 310 tool taper: SK 40 speeds: 20-4500 U/min weight of the machine ca.: 3 t dimensions of the machine ca.: 2,15 x 2,00 x 2,50 m Equipment/accessories: -swivel rotary table -documentation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Tool diameter: mm sanding disc diameter: mm Motor output: 3 kW total power requirement: 3 kw Weight: 1.400 kg Overall size: mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 600 mm y-travel: 500 mm z-travel: 500 mm total power requirement: 7,5 kW weight of the machine ca.: 5,5 t Working range: Longitudinal stroke X axis 600 mm Vertical stroke Y axis 500 mm Cross stroke Z axis 500 mm Clamping size of angle table 530 x 900 mm Max. weight of workpiece on table 450 kg Distance from table to vertical spindle, min./max. 120 / 620 mm Distance from table to horizontal spindle, min./max. 156 / 656 mm Tool taper SK 40 Spindle speeds 0 - 6,300 rpm Feeds X, Y and Z Axes, max. 2 - 10,000 mm/min Quick feed X, Y and Z Axes 10,000 mm/min Spindle drive 8 kW Total electrical load, approx. 15 kW - 400 V - 50 Hz Weight, approx. 5,500 kg Accessories / Special Features DIALOG 11 CNC Control in 4 axes with all the usual options, cycles, and subprograms. Graphic display and electronic hand wheel. Vertical milling head can be pushed up manually so that the  ...

x-travel: 300 mm y-travel: 150 mm z-travel: 340 mm total power requirement: 2 kW weight of the machine ca.: 660 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 300 mm y-travel: 450 mm z-travel: 150 mm total power requirement: 1,5 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 1170 mm y-travel: 500 mm z-travel: 370 mm table load: 2 t spindle turning speed range: 25 - 2500 U/min feeds: 4 - 2000 mm/min rapid traverse:: 4000 mm/min taper ISO: 40 total power requirement: 12,5 KVA weight of the machine ca.: 4 t dimensions of the machine ca.: 2,3 x 1,9 x 1,75 m The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created wit ...

grinding wheel diameter: - mm power requirement: 1 kW total power requirement: 1 kW weight of the machine ca.: 0,16 t dimensions of the machine ca.: 1,20,81,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 1200 mm y-travel: 400 mm z-travel: 400 mm total power requirement: 5 kW weight of the machine ca.: 2,5 t dimensions of the machine ca.: 3 x 2 x 2 m No. 4427 Universal tool milling machine DECKEL FP 4 L / 2707 Working area: 1200 x 400 Fixed angle table Control: 3-axis digital display Weight approx. 3.5 tons Space requirement 3 x 2 x 2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Digital Travel paths X/Y/Z: 400 x 200 x 400 mm Table size 700 x 330 mm Tool holder ISO 40 Vise, hydraulic Refurbished in 2019

x-travel: 710 mm y-travel: 600 mm z-travel: 455 mm Control: Dialog 4 turning speeds: 6300 U/min tool taper: SK40 quill stroke: 80 mm table-size: 550 x 1000 mm table load: 0,6 t total power requirement: kW weight of the machine ca.: 4 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Tool holder ISO 40, travel distances 800 x 300 x 400, 18 spindle speeds 40 - 2000, 18 feeds 10 - 500, rapid traverse, spindle motor 2.2 kW, Spindle backlash X-axis 0.3 mm, Y-axis 0.2 mm Bellows in X and Z axis new

Key data: 300 mm, 150 mm, 300 mm

Universal Milling DECKEL FP1 Travel X: 300 mm Travel Y: 150 mm Travel Z: 300 mm Horizontal + vertical spindle Spindle speed: from 40 to 2000 RPM Table size: 600 x 210 mm Horizontally tiltable head Straight table Spindle motor: 2 speeds Motor: 1,3 kW Feeds: X - Z auto / Y manual Voltage: 380 V Width: 1200 mm Depth with electrical panel: 1200 mm Height:1600 mm Weight: approx 900 kg

Key data: 500 mm, 400 mm, 400 mm

Deckel FP 4M Active with 3-axis active digital display, Year of manufacture 1996 Table clamping area 800 x 460 mm Travel X / Y / Z 500 / 400 / 400mm Spindle speed 50 - 2500 rpm Feed rate 8 - 630 mm/min Rapid traverse 1500 mm/min Quill stroke 90 mm Tool holder SK 40 Hydraulic Tool Clamp Very good condition!

Univ. swivel, tilt and turn table presumably DECKELUniversal tool milling machine attachment tableTable size: 700 x 400 mmGroove width: 14 mmGroove spacing: 46 mmMounting plate: width 550 mm x height 300/240 mm- Swivel and tiltable +/- 30- Rotatable 360Weight approx. 140 kg; used

Univ. Tool Milling Machine DECKEL Type FP 1Masch. No. 33064 Year of construction approx. 1960 Overhauled in 2012Travel distances X: 300 mm Y: 150 mm Z: 330 mmTable size 600 x 210 mmSpindle holder MK 4 - S20 x 2Spindle speed vertical 95-1900 rpm. 12 stepsSpindle speed horizontal 60-1200 rpm. 12 stepsMotor power 1.1 and 1.4 kWNerg connection 380 volts, 50 Hz- Feed in the X and Y axis- Pinol displacement on the vertical milling head- Fixed angle table- Coolant device with mechanical pump in the machine foot-

Univ. Swivel, Tilt and Turn Table DECKELUniversal Tool Milling Machine Attachment Table suitable for FP 2L or FP 3L or FP 4LNr. 2314-0301 Year of construction: approx. 1975Clamping surface: 1000 x 520 mm- 6 clamping grooves 16 mm, distance 90 mm- Clamping plate can be rotated horizontally to the right and left up to 45 degrees- Tiltable from/to the machine +/- 15 degrees- Swivel +/- 15 degrees- Swivel table, tilting table, angle tablePermissible load max. 1000kgWeight: 400kggood condition; used

Univ. Tool Milling Machine DECKEL Type FP 1Masch. No. 52185/08 Year of construction 1968Travel distances X: 300 mm Y: 150 mm Z: 340 mmTable size 600 x 250 mmSpindle holder SK 40 - S20 x 2Spindle speed 40-2000 rpm. 16 stagesMotor power 1.0 and 1.4 kW pole-switchableMains connection 380 volts, 50 Hz- Feed in the X and Z axis- Two motor speeds and 8 gear stages- Pinol shift on the vertical milling head 60 mm- Fixed angle table- Coolant device in the machine foot- Adjacent control cabinet- Counter holder

Univ. tool milling machine directly from one resolutionMilling machine DECKEL type FP 4Masch. No. 1/0687 Year of construction 1978Travel X: 700 mm, Y: 400 mm, Z: 450 mmTable clamping surface 860 x 500 mmSpindle holder SK 40 - M16Spindle speed 31.5 - 1600 rpm. 18 stepsQuill displacement horizontal and verticalMain spindle drive 4 kWNet connection 380 volts, 50 Hz- Digital display 3-axis HEIDENHAIN- Universal swivel-tilt turntable- Coolant device in the machine base- Machine vice- none

Univ. Tool Milling Machine DECKEL Type FP 1Masch. No. 51265/08 Year of construction approx. 1967Travel distances X: 300 mm Y: 150 mm Z: 340 mmTable size 600 x 2100 mmSpindle holder SK 40 - S20 x 2Spindle speed 40-2000 rpm. 16 stagesMotor power 1.0 and 1.6 kW pole-switchableMains connection 380 volts, 50 Hz- Feed in the X and Z axis- Spindle speed over 2 motor speeds and 8 gear stages- Pinol shift on the vertical milling head 60 mm- Fixed angle table- adjacent control cabinetSpace requirement L x W x H 1100 x

Univ. Tool Milling Machine DECKEL Type FP 1Masch. No. 34338 Year of construction approx. 1965Travel distances X: 300 mm Y: 150 mm Z: 340 mmTable size 600 x 200 mmSpindle holder MK 4 - S20 x 2Spindle speed vertical 95-1900 rpm. 12 stepsSpindle speed horizontal 60-1200 rpm. 12 stagesMotor power 1.0 and 1.5 kW pole-switchableMains connection 380 volts, 50 Hz- 3-axis digital display HEIDENHAIN, type VRZ 753 B- Spindle speed over 2 motor speeds and 6 gear stages- Feed in the X and Z axis coolant device with

Univ. Tool Milling Machine DECKEL Type FP 1Masch. No. 28317 Year of construction approx. 1960Travel distances X: 245 mm Y: 150 mm Z: 340 mmTable size 600 x 210 mmSpindle holder horizontal MK 4 - S20 x 2Spindle speed vertical 95-1900 rpm. 12 stepsSpindle speed horizontal 60-1200 rpm. 12 stepsMotor power 0.8 and 1.1 kW pole-switchableMains connection 380 volts, 50 Hz spindle speed over 2 motor speeds and 6 gear stages- Feed in the X and Z axis coolant device with mechanical pump in the machine base

x-travel: 1.000 mm y-travel: 1.000 mm z-travel: 1.000 mm Control: SINUMERIK 840D pl spindle turning speed - stepless: U/min total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m 5-axis machining center with SIEMENS SINUMERIK 840D pl control, electron. handwheel, NC swivel rotary table Ø1,000mm, coolant through the spindle, chip conveyor, 180-fold tool-magazine HSK100, The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 500 mm, 400 mm, 400 mm

FP 4M lid with 3-axis active digital display, Table clamping area 800 x 460 mm Travel X / Y / Z 500 / 400 / 400mm Spindle speed 50 - 2500 rpm Feed rate 8 - 630 mm/min Rapid traverse 1500 mm/min Quill stroke 90 mm  Tool holder SK 40 Hydraulic Tool Clamp Incl. accessories as shown

x-travel: 400 mm y-travel: 390 mm z-travel: 350 mm Control: DIALOG4/CONTOUR 3 tool taper: SK 40 spindle turning speed range: 31 - 3150 U/min feed range: 10 - 2000 mm/min total power requirement: kW weight of the machine ca.: 1,7 t dimensions of the machine ca.: 1.600 x 2.500 x 2.000 mm CNC control DIALOG4/CONTOUR 3 Table: 700 x 480 mm rigid angle table Swivel-type vertical milling head Coolant tank The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Spindle speed range: 9000rpm, travel X/Y/Z: 500mm/400mm/400mm, feed rate: 10000mm/min, rapid traverse: 12m/min. Table dimensions X/Y: 700mm/500mm, max. table load: 200kg, number of T-slots: 7, distance between T-slots: 63mm. Control: Heidenhain, tool changer: 16-fold, dimensions X/Y/Z: 4000mm/2200mm/2450mm, weight: approx. 3500kg.

Key data: 500 mm, 450 mm, 400 mm

5 Axis CNC Machining Center Universal CNC Milling Machine DMG Ecoline DMU 50 eco Year of construction: 2011 Siemens Sinumerik Conveyor Complete documentation 5-axis machining of simple to highly complex workpieces. Swivel rotary table Powerful milling spindle 8,000 rpm Tool Changer with 16 Places Pick-up Magazine Direct position measuring system and centrally lubricated roller circulation guide for high long-term accuracy. Ball screw in the linear axes The machine is in excellent condition and is still energized.

Univ. Tool Milling Machine DECKEL Type FP 1 Masch. No. 37101 Year of construction approx. 1969 Travel X: 300 mm Y: 150 mm Z: 340 mm Table size 600 x 200 mm Spindle holder MK 4 - S20 x 2 Spindle speed vertical 95-1900 rpm. 12 steps Spindle speed horizontal: 60-1200 rpm. 12 steps Motor power 1.0 and 1.5 kW pole-switchable Mains connection 380 volts, 50 Hz - Spindle speed over 2 motor speeds and 6 gear stages - Feed in the X and Z axes - Coolant device with mechanical pump in the machine foot - Quill shift on the vertical milling head 60 mm - Adjacent control cabinet Space requirements L x W x H 1000 x 900 x 1750 mm Weight 690 kg good condition Accessories: -Collets -Roundtable -Vice - Counter holder H. milling

x-travel: 500 mm y-travel: 400 mm z-travel: 400 mm Control: TNC 426M Heidenhain Main spindle:: turning speed range - main spindle: 20 - 9.000 min/-1 power capacity - main spindel: 9 / 13 kW max. Torque: 57 / 82 Nm tool taper: ISO 40 DIN 69871 swiveling-rotary-table:: table diameter: 700 x 500 mm swivellable: B: 105° (-10°/+95°) man. rotatable: 360° man. max. table load: 200 kg number of T-slots: 7 T-slot - distance: 63 mm T-slot - width: 14H7 mm center hole: 30H7 mm Tool-Presetter:: number of toolpositions: 16 pos. tool taper: ISO 40 DIN 69871 max. tool length: 290 mm max. tool weight: 6,0 kg max. total weight: 50 kg feeds:: feed speeds: max. 10.000 mm/min rapid traverse: 12 m/min input unit: 0,01 mm total power requirement: 17 kW weight of the machine ca.: 3,2 t dimensions of the machine ca.: 4,0 x 4,0 x 2,5 m Documents: Chip-Tray: Coolantsystem: B-axis: man. C-axis: man. Swi ...

Universal tool milling machine DECKEL FP 3 With 3 axes active digital display Heidenhain TNC 11 Year of Make: 1984 Travel: X 500 Y 300 Z 400 Speed range: 25 – 2500 rpm With the following accessories: Rigid angle table 850 mm x 400 mm clamping surface Swivel rotary table 0 450 mm with dividing discs Bumper Sliding vertical milling head Extendable drill quill Stepless feed via potentiometer Various milling mandrels SK 40 / S22 x 2 Chip tray Automatic lubrication pump for X,Y,Z axis Machine Light Coolant Setup 4 pcs machine shoes Operating instructions

Travel X/Y/Z: 560mm/500mm/450mm, tool holder: SK40, speed: 4000rpm, feed rate: 3.6m/min, rapid traverse: 4m/min, table dimensions X/Y: 530mm/900mm, max. table load: 450kg. Machine dimensions X/Y/Z: 2350mm/2200mm/2000mm, weight: approx. 2200kg, control: Deckel Contour 2. An on-site inspection is possible.

Key data: 300 mm, 150 mm, 300 mm

Universal Milling Machine DECKEL FP1 Travel X: 300 mm Travel Y: 150 mm Travel Z: 300 mm Horizontal + vertical spindle Spindle speed: from 40 to 2000 RPM Horizontally tiltable head Spindle motor: 2 speeds Motor: 1,5 kW Feeds: X - Z auto / Y manual Supplied without table only with one 4 concentric jaws Ø 140 mm Voltage: 380 V Width: 1200 mm Depth: 1200 mm Total height: 1600 mm Weight: approx 900 KG

DECKEL MAHO DMU 60 monoBLOCK 5-axis machining center GENERAL Project No.: 905799 Quantity: 1 pcs. Manufacturer: DECKEL MAHO Type: DMU 60 monoBLOCK Control: Heidenhain Millplus iT Year of Make: 2008 Condition: Used machine Approx (hrs): 38596 Spindle in approx. (hrs): 200 Program run approx. (hrs.): 16181 DESCRIPTION MILL 5 axes Travel in X 730 mm Travel in Y 560 mm Travel in Z 560 mm Max. rapid traverse speed in X/Y/Z 30/30/30 m/min Tool holder HSK 63 Max. speed milling spindle 18000 1/min Milling head NC-controlled swivel -120/+30 degrees Chain tool magazine 60 stations Machine table 1000x600 mm Rotary table NC-controlled Diameter of rotary table 600 mm OTHER EQUIPMENT IR Workpiece Probes Splash protection cladding with partially clad work area Rotating viewing window Lighting in the work area Preparation for central oil/emulsion mist ...