deckel 80 u used for sale

Parallel Lathe JET PROMAC 941 V Between points: 500 mm Maxi Ø on bench: Ø 240 mm Maxi Ø over saddle: Ø 140 mm Spindle diameter: Ø 21 mm Spindle speed: from 100 to 1700 RPM Square turret Chuck: 3-jaws Ø 125 mm Year of construction: 2012 - Almost new Spindle motor: 1,3 kW Threadings: Metric + Whitworth Tailstock: CM2 Variable speed drive for the spindle Supplied with one 4-jaws chuck Ø 125 mm Supplied with the gears for threading Electronic tachometer Voltage: 220 V mono Dimensions (L x W x H): 1200 x 600 x 1400 mm Weight: approx 200 kg

BERNARDO Variomill FU 2000E Servo universal milling machine was built in 2020 in Austria by PWA Handelsgesellschaft m.b.H. The machine, distinguished by its stable design made of grey cast iron and the use of modern technologies, is the perfect choice for machining heavy, oversized workpieces. All linear axes are driven by high-performance servo motors, which guarantee appropriate accelerations and feed rates in each direction. What’s more, the X axis has been coated with a special Turcite B coating to reduce the effect of slippage. All of this, combined with extensive equipment, maximises the precision and repeatability of the produced parts, even during the most intense challenges. The Variomill FU 2000E Servo vertical milling machine weighs 4500 kg. Technical specifications of the BERNARDO Variomill FU 2000E Servo milling machine - feed in the X/Y/Z axis: 1400/700/500 mm - rapi ...

GeneralVertical Machining centre; Control: DMG MORI ERGOline IV Multi-Touch CharacteristicsTable surface900 x 600 mmTool Magazine with30 PositionsMovement X / Y / Z600/600/510 mmRapid feed X / Y / Z30/30/30 m/minAC main driveSpindle speed range 20 to 15.000 rpm AC main drive:20/14,5 kW (40/100% DC) Tool taper SK40 DIN 69871 Tool clamping according to DIN69872Direct measuring system X,Y,ZDirect Measuring System X, Y, Z inclusive Air Purge for Measuring SystemTouch Probe Heidenhain TS 460Touch Probe HEIDENHAIN for workpiece measuring Option includes: - TS 460 Touch probe with optical signal transmission - measuring cycles - calibration ring - case for equipmentTouch probe Heidenhain TT160Touch Probe HEIDENHAIN for tool length and diameter measurement Option includes: - TT160 probe for tool measurement - measuring cycles with tool breakage monitoring - calibration tool Note: Additionally to ...

CharacteristicsTable surface900 x 600 mmTool Magazine with60 PositionsMovement X / Y / Z600/600/510 mmRapid feed X / Y / Z42/42/42 m/minGeneralVertical Machining centre; Control: DMG MORI ERGOline IV HEIDENHAIN TNC 7 Spindle speed range 20 to 12.000 rpmSpindle speed range 20 to 12.000 rpm AC main drive:13/9 kW (40/100% DC) Tool taper SK40 DIN 69871 Tool clamping according to DIN69872Direct measuring system X,Y,ZDirect Measuring System X, Y, Z inclusive Air Purge for Measuring SystemProduction Package 80 barProduction Package 80 bar Option includes: - Internal coolant supply 80 bar - Tank capacity: 600l with papertype filter - Chip conveyor (scraper type) with tank capacity: 200 l (left) - Bed flushing via M-Function - Coolant spray gun for swarf removal - EActive cooling systemActive cooling system for selected mechanical components in order to increase machine thermal stabilityAir coola ...

Turning diameter: 320mm, turning length: 1000mm, spindle clearance: 80mm, speed: 3150rpm, travel X/Z: 265mm/1000mm. Machine dimensions X/Y/Z: approx. 5500mm/2400mm/2400mm, weight: approx. 7000kg, control: Traub System TX-8. Including a tool set, three-jaw chuck and bar chuck with collets. Documentation available. On-site inspection is possible.

Key data: 140 °C, 10 kW

Max. heating capacity - 140°C Heat transfer medium – water Power: 10 kW Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended

Key data: 140 °C

Temperature control unit of the tools - Tool Temp TT-118K / MP-988 (3 pcs.) Year of Make: 2020 Location: Lodz, Poland Description: Max. heating capacity - 140°C Heat transfer medium - water Power: 29.3 Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended All offered devices are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected device or to participate in live technical tests at our company in Łódź. Price: On request

Key data: 160 °C, 20 kW

Temperature control unit of the tools - Single STW 180/1-18-70-N1.1 (2 pcs.) Year of Make: 2013 Location: Lodz, Poland Description: Max. heating capacity - 160°C Heat transfer medium – water Power: 20 kW Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended All offered devices are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected device or to participate in live technical tests at our company in Łódź. Price: On request

Key data: 140 °C, 10 kW

Temperature control unit for tools - Wittmann Tempro Plus (15 pcs.) Year of manufacture: 2009-2018 Location: Lodz, Poland Description: Max. heating capacity - 140°C Heat transfer medium – water Power: 10 kW Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended All offered devices are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected device or to participate in live technical tests at our company in Łódź. Price: On request

Key data: 90 °C, 10 kW

Temperature control unit for tools - Wittmann Basic-C90 Year of Make: 2015 Location: Lodz, Poland Description: Max. heating capacity - 90°C Heat transfer medium – water Power: 10 kW Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended All offered devices are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected device or to participate in live technical tests at our company in Łódź. Price: On request

Key data: 585 mm, 4064 mm

JARBE Universal Cylindrical Grinder Year: 1981 Technical Specifications & Features: • Swing Over Table: 23″ Distance between centers 160” • Hydraulic Table Traverse • Swiveling Table for Taper Grinding • Universal Workhead • Universal Wheelhead • Grinding Wheel Capacity: 20″ • Includes 2 Workrests • Equipped with Coolant System • Electrics: 440 Volt

Key data: 90 °C

Temperature control unit of tools - Tool Temp TT-188 (20 pcs.) Year of construction: Location: Lodz, Poland Description: Max. heating capacity - 90°C Heat transfer medium – water Power: 9850 watts Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended All offered devices are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected device or to participate in live technical tests at our company in Łódź. Price: On request

Linear unit, linear axis, portal axis with servo drive, synchronous servo motor, electric slide, loading unit, linear guide with servo motor and pneumatic gripperREXROTH INDRAMAT Type: MKD0771B-061-KP1-KNIdent No. 247238 0001Year of construction: 2000Axis movement: 2400 mmCarriage length: approx. 500 mmTotal length: 3520 mm- pneumatic feed pliers (clamping pliers with 2 Festo compressed air cylinders)- Standard linear guide 65 x 25 mm- basic profile made of steel- ball screw 32 x 10 mm- pneumatic with position indicator- Permanent Servo Motor Type:

Univ. swivel, tilt and turn tableAttachment table for Univ. tool barrel machineTable size 630 x 250 mmGroove width 14 mmRotatable and tiltable +/- 30Swivel +/-45- 4x T-grooveWeight approx. 120 kg; used

Hydraulic power unit with hydraulic pump BOSCH REXROTHHydraulic power unit Year of construction approx. 2000Operating pressure pump1: 10 barVolume flow pump1: 24 litres/min. Engine power pump1: 1.5 kWoperating pressure pump2: 120 bar (max.140 bar)Volume flow pump2: 44 litres/min. Engine power pump2: 11 kWTankle capacity: 200 litresMains connection: 400 volts, 50 Hz- 2 independent hydraulic pumps, each with its own drive motor- 6 hydraulic valves built- Cleaning cover in the oil tankSpace requirement L x W x H 1000 x 700 x 1200Weight:

Clinch unit TOX - Pneumatic-Hydro Tox pressHydro-pneumatic press TOX Pressotechnik POWER PACKAGEType type CRS 03.62No.: 207599.2Year of construction approx. 2005Pressure capacity: max. 80 kN = 8 tonProjection: 20 mmInstallation height: 32 mm- Built-in clinch tool- pneumatic valve for control- Push-through joining or clinching- For making a form-fit connection of 2 sheets without perforating or heating the sheets- Mounted on the stand- with the simplest electrical control and Foot switchWeight: 230 kgComes from

Welding turntable - Welding rotary device with housingRound welding deviceLoad capacity approx. 50 kgTurning chuck diameter 300 mmTurning chuck speed 1.0-15 rpm. Mains connection 230 volts, 50 Hz- Spiral lathe chuck with inwardly stepped chuck jaws- Speed control infinitely variable via potentiometer- Drive via gear motor, direction of rotation left- Start via electric switch- Welding current transmission with sliding contact- Extraction connection 160 mm- Interior lightingDoor opening W x H 715 x 1060 mmInterior dimensions W x D x H

Slot head for milling machine, milling head, CCCP / USSR STANKO Type 1502Nr: 200 Year of construction 1974Stroke size: max. 60 mmStroke rate: approx. 200 - 500 strokes/min. Tool holder: 12 x 17 mm with clamping plateHole spacing machine-flange plate: 245 x 185 mmMounting hole: 17 mmCentering diameter on the machine flange plate: 190 mm- Stroke size adjustable via eccentric adjustment- The drive is as with the normal vertical head from the machine gearbox- Drive via driver, centric in the centering diameter- Degree scaling at the

CNC Univ. Tool Grinding Machine SCHÜTTE Type BU 400 CNC 4Machine - Defect - without ControlMachine not ready for operation - electric without function - without CNC controlFabr. No: 03-02 Year of manufacture 19904 axes (X, Y, Z and R)Table clamping surface 1300 x 250 mmCenter width 700 mmCenter height 155 mmGrinding length (X-axis) max. 400 mmGrinding width (Y-axis) max. 260 mmGrinding spindle speed max. 6000 rpm. Grinding spindle drive 3 kWNet connection 380 Volt, 50 Hz, 25 Amp.- CNC control

Hydraulic power unit with hydraulic pump BOSCH REXROTH / HYDRONORMAHydraulic power unit Year of construction approx. 1985Operating pressure: max. 65 barVolume flow: 20 litres/min. Fuel tank capacity: 110 litersEngine power: 3 kWMortor speed: 1440 rpm. Mains connection: 400 volts, 50 Hz- 1 piece hydraulic vane pump MANNESMANN REXROTH, type 1PV2V3-40/25RA01MC63A1- 1 piece drive motor KATT, type FFN 100L- 1 piece pressure reducing valve BOSCH REXROTH, type DR 8 G433/100 YM- 1 piece return filter- 1 piece 4/2-way hand valve (e.g. for retracting and extending a double

Hydraulic power unit with hydraulic pump RACINE / VICKERSHydraulik gensetOperating pressure: max. 44 barVolume flow: 13 litres/min. Tank capacity: 40 litersEngine speed: 950 rpm. Engine power: 0.75 kWNetz connection: 380 Volt, 50 Hz- 1 piece hydraulic vane pump PVQ-PSS=-06CR-J11- Hydraulic tank with maintenance cover and oil level sight glass- 2 pieces hydraulic hoses with 12L connections, length = 950 mmSpace requirement L x W x H:: 700 x 400 x 750 mmWeight: 97 kg (without oil content); used

Table unit from a DROOP & REIN portal milling machineClamping plate with T-slots made of cast steel-gray cast ironTable unit with clamping plate and very solid guidewayTable clamping surface 5500 x 2000 mmTravel distance of the table clamping plate approx. 3100 mmTable height-height 1050mmTable load: max. 20 ton. Ball screw: 100 mmThread pitch: 20 mm (single)- Machining table very stable on the bed- Metal telescopic guideway cover - comes from a DROOP & REIN portal milling machine- Longitudinal table movement over

Universal temperature control unit WEINREICH type WTD 4Temperature control unit with electric heating and connections for external coolingFabr. No.: 11932217 year of construction 1993Temperature max. 140CBorcing pressure max. 6 barPump capacity 30 l/min. Tank volume 4 litresHeating capacity 4 kWeergisation capacity heat exchanger 15 kWCotor capacity of the pump 0.37 kWUmrune water supply + return G 3/8Cooling water flow + return G 3/8Total capacity 4.4 kWNe-connection 380 volts, 50 Hz, CEE plug-in temperature control medium water

Filter fitting, filter unit COMPAIR for compressor systemsCompressed air filterType: CF 0087B ZPFabric no: 3363006 / 05 / 005Operating pressure: max. 16 barThreaded connection: G 1 1/2Flow rate: approx. 8.5 m³/min Filter element no: CE 0087B- Filter housing made of aluminiumWeight: 5 kgDimensions L x W x H 125 x 110 x 420 mmgood condition; used

Cooling unit, cooling water recirculating cooler, water cooler, chiller O. HellwigYear of construction: approx. 1995Cooling capacity approx. 6 kWNight cooling unit 3 kWaverse refrigerant R422DWasser tank capacity approx. 35 litresFlow volume circulation pump 40 litres/minPump capacity 0.63 kWWasser connections 1/2 inchMains connection 380 volts, 50 Hz- temperature setting via rotary potentioSpace requirement L x W x H 1100 x 750 x 140 mmWeight 285 kg; used

Universal face and boring head LENZ type LPA 1SSpindle tool, spindle head similar to WOHLHAUPTER UPA3Tool holder: SK 40 - M16Adjustment accuracy: 0.01 mm- Accessories as shown- Storage boxWeight: approx. 5 kggood condition; used

Hydraulic punch, punching rack for the use of punching units JOKA type HP-SHydraulic hole punch, hydraulic press for punching bracketYear of construction approx. 1995Printing capacity 5 ton. Projection 155 mmStroke approx. 20 mmPunching unit width max. 54 mmPunching unit height max. 220 mmDie holder 48 mmMotor power 1.5 kWNeching connection 230 volts, 50 Hz- for the universal use of punching units JOKA SW 20 or SWD 20- Projection of the punching units can be larger, can be pushed through to the rear- Stroke release via

Univ. NC Tool Milling Machine KUNZMANN Type WF 3/4Masch. No. 341020 Year of construction 1998Travel distances X: 400 mm Y: 320 mm Z: 400 mmTable size 650 x 350 mmSpindle holder SK 40Spindle speed 40 - 2500 rpm. Feeds X, Y and Z axis 0 - 1000 mm/min. infinitely variableRapid traverse X, Y axis 4000 mm/min. Rapid traverse Z-axis 3000 mm/min. Quill adjustment vertical 60 mmDrive power Spindle motor 3 KWnet connection 400 volts, 50 Hz- CNC line control Heidenhain TNC 124- Spindle speed via 2 gear stages and

Hydraulic power unit for mobile clinching pliers or mobile former ECKOLD type HA 500 / 2Fabr. No. 737 / 783 Year of construction 1991Hydraulic power unit type HA 500 / 2Operating pressure 50 - 500 bar adjustableFlow rate 2.6 l/minTank capacity 16 litresEngine power (hydraulic) 3 kWNead power 380 Volts, 50 Hz.Control voltage 24 Volts, DC pressure line with screw coupling- With solenoid valve HAWE GS 2-2- mobile on 4 swivel castorsWeight without hydraulic oil 125 kggood condition; used

Cooling Unit Cooling Water Recirculating Cooler ARO Type VWK 31/1-SFabr. No. 0705384 year of construction 2007Cooling capacity 3500 wattsAmbient temperature max. 32CRefrigerant R407CCrefrigerant Capacity 0.98 kgOperating overpressure Refrigeration compressor max. 29.5 barWater tank capacity approx. 8 litresFlow volume Circulating pump 27 litres/min. (1620 litres/h)Water connections Quick-release coupling Rectus Type 26Mains connection 230 volts, 50 Hz, 2.2 kW- temperature setting via DANFOSS thermostat controller- built-in circulation pump (250

A Wieland extraction system is available. Engine speed: 2930rpm, power: 18.5kW, weight: approx. 1200kg. Documentation available. On-site inspection is possible.

Tightening Banding Machine for Shrink Film

KZE unit, consisting of: buffer tank 6.0 bar 12,750 ltr. Capacity capacity: max. 25,000 ltr/h designed for 14 bar plate heat exchanger GEA with 20 bar pressure material of the system 1.4301 year of construction: approx. 2007 only few operating hours last overhaul in 2018, the little used including electro plan

Beck Wand 1000/2000 Extraction Wall Extraction wall Type: Beck Wand 1000/2000 Extraction wall made of sheet steel, with 5 suction slots made of perforated sheet metal evenly distributed. For connection to a central extraction system via a suction nozzle at the top center of the extraction wall. Cleaning opening can be unscrewed at the bottom of the front of the wall. Uses: Extraction of process air during grinding and milling Extraction of gases and light dust Extraction of powder mix or other stationary dust-forming processes Width: 1000 mm Height: 2000 mm + 100 mm nozzle Depth: 300 mm Suction nozzle: NW 250 top center Recommended extraction capacity: 3000 m3/h Paintwork: RAL 5018, RAL 7032 Weight: approx. 75 kg Manufacturer's price: 2970,-€ More items - new and used - can be found in our shop! International shipping costs on request!

Plastic Dryer - Wittmann Drymax Primus E60-150-M (2 pcs.) Year of Make: 2016 Location: Lodz, Poland Description: Dryer with 2 molecular sieves, 1-silo Silo capacities: 150 l Sieves work alternately, during the drying process, one sieve works and the second sieve regenerates Hermetically insulated silo Dryer with Wittmann Feedmax S3-Net suction conveyor Price: On request

Plastic dryer - Wittmann Drymax E30-70-M / Very good technical condition Year of Make: 2015 Location: Lodz, Poland Description: Dryer with 2 molecular sieves, 1-silo Silo capacities: 150 kg Sieves work alternately, during the drying process, one sieve works and the second sieve regenerates Hermetically insulated silo Dryer with Wittmann suction conveyor Price: On request

Plastic Dryer - Wittmann Drymax D60-150-M (2 pcs.) Year of Make: 2011 Location: Lodz, Poland Description: Dryer with 2 molecular sieves, 1-silo Silo capacities: 150 l Sieves work alternately, during the drying process, one sieve works and the second sieve regenerates Hermetically insulated silo Dryer with Wittmann Feedmax S3-40 suction conveyor Price: On request

This offer is aimed exclusively at entrepreneurs within the meaning of § 14 BGB. The price is net plus 19% VAT. Manufacturer: Emerson Macchine Torino Type: Carrera 700 Year of Make: 2021 Specifications: Table size: 1,320 x 320 mm • X - Y stroke: 1,000 x 290 mm • Stroke of the Z-table: 400 mm • Distance from spindle table: 140 - 540 mm • Distance from spindle to column: 200 - 550 mm • Spindle stroke: 120 mm • Spindle taper: ISO 40 • Drilling capacity: 30 mm • Tapping capacity: M 16 • Vertical spindle speed: 90 - 2,000 rpm • Horizontal spindle speed: 40 - 1,350 rpm • Horizontal/vertical motor power: 2.2/1.5 kW • Dimensions: 1,920 x 1,850 x 2,200 mm • Weight: 1,900 kg Standard equipment: • Automatic tool screwdriver •Transmission • Horizontal spindle • Automatic feeds on the axles • Automatic spindle descent •Chiller � ...