126,676 used machines on RESALE, but how to find them? Machine Search
: gebraucht : 2020 : 1658 : prompt, Zwischenverkauf v : Bulgarien : 26500 € : 1 : 22600 € : 400 mm : 1000 mm : 200 mm : 52 mm : 235 mm : 320 mm : 6 : 6 MK : 12 : 50-2.240 1/min : 80 : 0.015 - 0.6 mm/U : 0.0075 - 0.3 mm/U : 40 : 0.25 - 7.5 mm : 120 - 4 Gänge/ : 0.0625 - 1.875 : 235 mm : 110 mm : 50 mm : 4 MK : 100 mm : 4 kW : 2750 mm : 1100 mm : 1600 mm : 1540 kg This machine is used in our workshop for repair work, therefore it has only been used very little so far. (New price € 36,070.00) driven by manual transmission 3-axes digital readout Fagor 40i quick change toolpostMultifix Type Bwith4 holders (3 square, 1 round) 3-jaw chuck Bison 3204/DIN6350, Ø 200 mm spindle noseNr. 6 DIN 55027 four way rapid traverse device spindle dead center coolant equipment 1 pce. flange plate for lathe chuckØ 200 mm 1 adapter sleeve full length rear splash guard leadscrew and shaft protection saf ...
: neu : ca. 12 Wochen ab Auftrags : Türkei : 8200 € : 158.26 € : 1250 kg : 1300 mm : 450 - 550 mm : 400 mm : 50 mm : 80 mm motorized drive mechanical adjustable coil mandrel with 4 jaws speed control for decoiling speed aswell as acceleration- and deceleration times photoelectric proximity ensor SICK for sag control Alternative: Variant with pneumatic pressure arm (CMC P3 1250 400 M D1300) € 10.900,-- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sliding table length: 3200 mm; cutting width at the fence: 1350 mm; cutting width at the cross cut: 3200 mm; cutting depth: 125 mm; scoring unit: ja; sawblade diameter: electric; tilting adjustment sawblade: electric; adjustment fence: manuell; readout sawblade tilting: Scala; read out sawblade height: -; read out fence: Scala; read out crosscut stop: Scala; sawblade diameter: 400mm; number of speeds: 3000 / 4000 / 5000 U/min; motor power: 7 kW; motor brake: yes, automatic; suction connection: 80mm und 120mm; machine length: 3400mm; machine width: 2000mm; weight: 900kg;
working width: 400 mm; maximum workpiece thickness: 300 mm; min. Workpiece length: 250 mm; aggregate: 2 Bürsteinheiten centrally adjustable and each with a single fine adjustment; 1. brush: methal brush, diameter 220mm; 2. brush: thynex brush granulation 80, diameter 220mm; height adjustment: handwheel; readout workpiece thickness: mechanical counter; feed speed: 4 - 12 m/min; motor power brushes: 2 x 3 kW; motor power feed: 0,37 kW; machine length: machine width: weight: In this machine, the brushes are pivotable diagonally to the feed direction, As a result, the edges are broken similar to oscillating brushes.
working width: 400 mm; maximum workpiece thickness: 300 mm; min. Workpiece length: 250 mm; aggregate: 2 brushing units separately adjustable; 1. brush: metal brush 220mm; 2. brush: tynex brush, granulation 80, diameter 220mm; height adjustment: handwheel; height adjustment: mechanical counter; feed speed: 4 - 12 m/min; motor power brush: 2 x 3 kW; motor power feed: 0,37 kW; machine length: 1400mm; machine width: 900mm; weight: 500kg;
Turning length/ centre width 4m, Spindle inner diameter, Face Plate D 1000 m, Center height over support 360 mm, 2 Risings with roller jaw guide 1980 Retrofitted, Main spindle speed 215 - 355 rpm. Operations manual with circuit diagram, chip protection, Reversible steel holders, Supports have currently been overhauled, electric lock box, Weight approx. 15 tons, Guided tour possible, including attempted filming.
turning diameter:640 / 400 mm turning length:1500 mm control:Siemens 840 D Powerline Travel turret No.1 (milling spindle) x/y/z:550 / 180 (±90) / 1585 mm Swivle angle milling spindle (B-axis):±120° interpol. ° Rapid traverse feeds turret 1 (milling head) x/y/z:40/24/60 m/min RPM milling spindle:12000 1/min power capacity - milling spindle:12 / 23 kW Torque of milling spindle:100 Nm Tool magazine for milling spindle (turret 1):120 HSK-A 63 Tool change time tool/tool, milling spindle:1,6 s Spindle 1 RPM:4000 1/min Spindle 1 power:36/ 45 kW Spindle 1 Torque:730 Nm Spindle 1 max. bar diameter:90 Spindle 2 RPM:4000 1/min Spindle 2 power:36 / 45 kW Spindle 2 torque:730 Nm Spindle 2 max. bar diameter:90 c-axis:0,001 ° Travel turret 2 x:225 mm Travel Turret 2 z:1595 mm RPM of rotary tools turret 2:4000 1/min no. of tools in turret 2:12 VDI 40 high-pressure pump:20 bar total power requiremen ...
x-travel:600 mm y-travel:580 mm z-travel:530 mm distance spindle center to column:630 mm distance spindle center to table:100-600 mm milling feed range:1-10.000 mm/min max. table load:200/100 kg max. tool weight:8 kg positioning accuracy:+/- 0,01 mm :8000/15000 1/min spindle drive:7,5/11,5 /5,5 kW repeating accuracy:+/- 0,008 mm weight of the machine ca.:7,4 / 7,65 t Brand-new CNC vertical machining center with CNC control FANUC or HEIDENHAIN Warranty: 12 months More information can be found in the Appendix.
pressure:250 t table length:4000 mm table width:3000 mm Controls:SIEMENS SIMATIC C7 PRESS DESIGN:. - frame design : 4 column :. - moving bolster : yes :. PRESS FORCES:. - total force (nominal):250 to PRESS TABLE:. - clamping surface (left-right):4000 mm - clamping surface (front-back):3000 mm - tool weight max.:100000 kg - number of T-slots:12 - distance between T-slots:375 mm - height above floor level:390 mm RAM:. - clamping surface (left-right):4000 mm - clamping surface (front-back):3000 mm - number of T-slots:12 - distance between T-slots:375 mm - stroke:2900 mm - tool weight max.:50000 kg RAM (HYDR. PRESS):. - number of main-cylinders:1 - approximation velocity max.:180 mm/s - working velocity max.:50 mm/s - restoring force of ram:95 to TOOL ASSEMBLY DIMENSIONS:. - distance table - ram max.:2750 mm - distance between columns (H-frame):4100 mm - Free passage be ...
rotor dia:30-500 mm hobbing length:500-1000 mm total power requirement:80 kW weight of the machine ca.:15 t dimensions of the machine ca.:3,6 x 2,5 x 3,0 m max. module:8 Max. module Et milling = 12 Max. module hobbing = 12 Max. axial travel = 110 to 1100mm Max. cutter speed = 300rpm Max. cutter displacement tangential = -350 to -55mm Max. table speed = 100rpm Table drive: torque motor Filter system: chip conveyor is for magnetic materials, belt filter is for all suspended matter that floats in the oil Including milling mandrel
x-travel:500 mm y-travel:400 mm z-travel:330 mm table-size:710 x 410 mm spindle taper ISO:40 quill stroke:100 mm control:HEIDENHAIN TNC 335 B table load:180 kg no. of flutes:8 groove width:14/25 mm tool taper:SK 40 speeds::20 - 3000 U/min feeds:infinitely variable1-1250 mm/min rapid traverse:5000 mm/min total power requirement:13 kW weight of the machine ca.:2500 kg dimensions of the machine ca.:2000 x 2800 x 2300 mm Year:ca. 1984 Zusatzinformationen ? Schile-Elektroschrank mit CNC-Steuerung Heidenhain TNC 355 ? Starrer Winkeltisch 710 x 400mm ? Spritzschutzverkleidung / Halbkabine ? Kopf nach Skala präzise drehbar über Kurbel ? Kopf komplett wegschwenkbar für horizontal Spindel
x-travel:1190 mm total power requirement:25 kW feeds::3 - 2000 mm/min weight of the machine ca.:4,3 t table-size:1600 x 400, 5 Spannbacken mm dimensions of the machine ca.:4000 x 3600 x 2200 mm speeds:45 - 1800 U/min y-travel:530 mm z-travel:540 mm tool taper:ISO 50 control cabinet:940 kg
x-travel:500 mm y-travel:400 mm z-travel:330 mm table-size:400 x 710 mm spindle taper ISO:40 quill stroke:100 mm control:HEIDENHAIN TNC 335 table load:180 kg no. of flutes:8 groove width:14/45 mm tool taper:ISA 40 speeds::20 - 3000 /28- 4000 U/min feeds:infinitely variable1-1250 mm/min rapid traverse:5000 mm/min total power requirement:13 kW weight of the machine ca.:2500 kg dimensions of the machine ca.:2000 x 2800 x 2300 mm Documents:inkl. Zusatzinformationen ? Schile-Elektroschrank mit CNC-Steuerung Heidenhain TNC 355 ? Starrer Winkeltisch 710 x 400mm ? Spritzschutzverkleidung / Halbkabine ? Kopf nach Skala präzise drehbar über Kurbel ? Kopf komplett wegschwenkbar für horizontal Spindel
x-travel:500 mm y-travel:250 mm z-travel:325 mm table-size:400 x 200 mm T-slots:10/ 20 mm T-slots:4 St workpiece height max.:300 mm template table:380 x 380 mm speeds::2500 - 20000 U/min no. of turning speeds:3 total power requirement:0,25 kW weight of the machine ca.:430 kg dimensions of the machine ca.:1000 x 1200 x 1500 mm
saw blade diameter:400 mm cutting diameter:400 mm material:Vollmaterial 20 - 130 mm material:Walzprofile 40 - 120 mm material diameter from - to::Rohr u. Profilfrohr bis 100 x 14 mm sawblade width:4 mm total power requirement:5,1 kW weight of the machine ca.:1850 kg dimensions of the machine ca.:3300 x 1630 x 1960 mm Documents:vorhanden
x-travel:850 mm y-travel:500 mm z-travel:610 mm rotary table::400 mm spindle turning speed range:12.000 1/min drive capacity - spindle motor:17/10 kW control:HEIDENHAIN iTNC 530 Tool changer:40- fach spindle taper ISO:SK 40 weight of the machine ca.:7,7 t total power requirement:28,5 kW dimensions of the machine ca.:3 x 2.70 x 3,2 m 5-axis simultaneously universal-machining center, NC-rotary-swivelling table dia. 400mm, 3D infrared touchprobe, el. handwheel, chipconveyor, airblast through spindle, internal coolant supply 40bar, flushgun, direct measuring system, approx. 38.000h "machine on", approx. 14.500h "spindle on"
x-travel:600 mm y-travel:580 mm z-travel:580 mm numbers of pallets:2 pallet size::400 x 400 mm max. workpiece weight:400 kg spindle taper ISO:40 spindle speeds::35 - 12000 feed speeds:1 - 50000 mm/min rapid speed:50 m/min total power requirement:25 kW weight of the machine ca.:12 t dimensions of the machine ca.:3,6 x 3,6 x 2,9 m with CNC SEICOS 16 M ( FANUC base ) autom. toolchanger 61-pockets pallet indexing 1° chip conveyor and coolant attachment exhauster clamping cube and diverse toolholders
pressure:400 t distance between columns:3250 mm distance table/ram, max. stroke up, adjustment up:1000 mm stroke:800 mm table surface area:3250 x 1400 mm table height over floor:1250 mm die cushion capacity:170 t die cushion stroke:200 mm die cushion area:1800 x 1000 mm distance between cutting impact cushioning:2610 mm side window:800 mm ram surface:3250 x 1400 mm return capacity:51 t speed down:300 mm/s speed up:300 mm/s working speed:16 - 33 mm/s quantity of oil:2900 l power requirement:100,0 kW weight:70,0 t Dimensions (WxDxH):4,9 x 3,1 x 7,6 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 cutting impact absorption:hydraulic
pressure:400 t distance between columns:1250 mm stroke:250 fix mm no. of strokes:45 /min distance table/ram, max. stroke up, adjustment up:825 mm table surface area:1000 x 900 mm column travel -side:400 x 700 mm ram surface:1000 x 900 mm ram adjustment:100 mm capacity of ejector in table:40 t ejector stroke:160 mm power capacity:270,0 kW weight:44,0 t Dimensions (WxDxH):2,4 x 3,6 x 7,2 m height over floor:6,4 m
material width:400 mm coil weight:3,0 t material thickness:0,5 - 4,0 mm coil internal diameter:460 - 530 mm coil external diameter:1500 mm no. of straightening rolls:9 straightening roll diameter:50 mm no. of lower support rolls:12 no. of upper support rolls:10 diameter of support rolls:90 mm material cross-cut:1600 mm² speed of coil line:0 - 20 m/min power requirement:35,0 kW weight:10,5 t dimensions (WxDxH):10,0 x 2,5 x 2,9 m straightening machine:KRE 50.400/9 adjustment of straightening rolls :motoric insertion wedge:hydraulic adjustable decoiler:3000.1 snubber roll:hydraulic expansion:hydraulic sideway adjustment:motoric pivoting:manual roll feed:Servo; WVE 160/400 intermittant lifting:hydraulic
Pressure:063 t throat:400 mm stroke:16 - 90 mm no. of strokes:60 /min distance table/ram, max. stroke up, adjustment up:350 mm table surface area:1000 x 750 mm hole in the table:260 x 140 mm table height over floor:710 mm ram surface:600 x 220 mm ram adjustment:50 mm weight:4,3 t dimensions (WxDxH):1,1 x 2,6 x 2,4 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch:pneumatisch overload protection in ram:mechanisch ram counterbalance:pneumatisch
pressure:400 t throat:520 mm stroke:20 - 200 mm no. of strokes:30 /min distance table/ram, max. stroke up, adjustment up:680 mm table surface area:1600 x 1000 mm table height over floor:715 mm passage to the back:1000 mm ram surface:1300 x 800 mm ram adjustment:130 mm power requirement:38,0 kW weight:41,0 t dimensions (WxDxH):2,1 x 2,6 x 4,2 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch-/ brake combination:pneumatic, Ortlinghaus overload protection in ram:hydraulic ram adjustment:motoric ram counterbalance:pneumatic
pressure:400 t stroke:280 mm no. of strokes:56 Hub/min distance table/ram, max. stroke up, adjustment up:680 mm table surface area:560 x 750 mm allowed max. force:600 t blow die to die:800 t spindle diameter:200 mm ram surface:560 x 560 mm height over floor:4,1 m power requirement:37,0 kW weight:12,0 t dimensions (WxDxH):2,2 x 2,0 x 4,25 m
pressure:400 t distance between columns:1100 mm stroke:250 mm no. of strokes:25 - 75 /min distance table/ram, max. stroke up, adjustment up:900 mm table surface area:1100 x 965 mm capacity of ejector in table:30 t ejector stroke of ejector in table:80 mm capacity of ejector in ram:3 t stroke of ejector in ram:60 / 70 mm ram surface:980 x 800 mm column travel -side:800 mm ram adjustment:20 mm power capacity:80,0 + 5,5 kW weight:47,0 t Dimensions (WxDxH):3,5 x 3,3 x 6,0 m weight of switch cabinet:1,4 t dimensions of electrical cabinet (WxDxH):4,9 x 0,5 x 2,6 m ejector in ram:hydraulic
pressure:160 t throat:400 mm stroke:30 - 200 mm no. of strokes:50 /min distance table/ram, max. stroke up, adjustment up:600 mm table surface area:1000 x 770 mm table height over floor:810 mm hole in the table:360 mm Passage to the back:450 mm ram surface:710 x 450 mm ram adjustment:110 mm power requirement:15,0 kW weight:10,5 t Dimensions (WxDxH):1,7 x 2,0 x 3,2 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch:hydraulic overload protection in ram:mechanical ram counterbalance:pneumatic
pressure:400 t distance between columns:1060 mm stroke:450 mm no. of strokes:15 - 30 /min distance table/ram, max. stroke up, adjustment up:1160 mm table surface area:1000 x 700 mm capacity of ejector in table:2 x 16 t ejector stroke of ejector in table:125 mm Die cushion pressure in table:120 t Die cushion stroke in table:2 mm capacity of ejector in ram:2 x 4 t stroke of ejector in ram:100 mm ram surface:1000 x 700 mm column travel -side:630 mm power capacity:55,0 kW weight:50,0 t die cushion in table:2. station
General SKU244Y171 LocationBarneveld CEcheck Main Features MaterialStainless steel Motor11 KW Inlet diameter22 mm Specified Features - Basket centrifuge MaterialStainless steel 1.4404 (316L) Basket centrifugecheck Closed basketDuplex 2205 Capacity100 dm³ Basket sizesø 800 x 400 mm Max. loading weight125 kg Hydraulic operatedcheck Liquid outletDN100 With hydraulic unitHydra power Motor1,50 kW, 400 V, 1445 rpm With variable speed drivecheck Max. basket speed2600 rpm Max. temperature0° / 80 °C Information MakeRiera Nadeu Serial10590/P19/00726 Magento base g_extra_specificationsBasket dia. 800mm, Max. 2.600 Rpm, solid wall basket, contact parts in stainless steel AISI-316L / DIN1.4404, Basket wall in Duplex 2205, Max. allowable weight 125 KG according to technical documentation (manufacturer tag mentions 180 KG), motor 11,0 KW, 400/690 Volt, with control cabine ...
General SKU310N454 MakeGebrüder Lödige Maschinenbau GmbH TypeK-TM 400 No.15383 Year of construction2004 LocationBarneveld Main Features MaterialStainless steel Volume400 Ltr. Motor15 KW Specified Features - Powder turbo mixer MaterialStainless steel Lödige mixercheck Continuous mixercheck Capacity400 Ltr Trough sizesdia.500mm x2000mm Inletdia.200mm Top connections(1x)dia.80mm, dia.45mm Inspection hatch(2x)500x350mm Outlet300x280mm Glands air purgedcheck Motor15 KW Speed mixing shaft117 rpm With lump breaker(only 2x connectionflange) Information Floorspace4,3x0,8 Total height0,9MStarchOther chemicalSpicesCatalysts & fillersFeed additivesOther pharmaceuticsCosmeticsFood additivesSugarAnimal feedOther feedConfectionerySolid pharmaceuticsDyes & pigmentsPowder turbo mixersMinerals & inorganicTea, herbs & coffeeGeneric medicinesPowdered foodsLoedigeIndustries > F ...
General SKU026W131 MakeDrais TypeKT-400 Year of construction1991 Mounted on framecheck Main Features MaterialStainless steel Volume400 Ltr. Motor18.5 KW Specified Features - Powder turbo mixer Powder turbo mixercheck Continuous mixercheck Capacity400 l. Trough sizesø 600 x 1450 mm Inlet250 x 300 mm Top connectionscheck 4x Inspection hatch400 x 370 mm Outlet290 x 250 mm With adjustable packing glandscheck Motor11,0 kW (380 V, 1450 rpm) Speed mixing shaft100 rpm With lump breakercheck Motor7,5 kW (380 V, 2780 rpm) Speed lumpbreaker2870 rpm MaterialStainless steel Information LocationBarneveld Floorspace2,8 x 1,5 m Total height1,7 m Weight1640 kgStarchOther chemicalSpicesCatalysts & fillersFeed additivesDiscountOther pharmaceuticsCosmeticsFood additivesSugarAnimal feedOther feedConfectionerySolid pharmaceuticsDyes & pigmentsPowder turbo mixersMinerals & inorg ...
General SKU035T171 LocationBarneveld Material Housing materialStainless steel Rotor materialStainless steel Main Features MaterialStainless steel Motor2.2 KW Inlet diameter400 mm Specified Features - Rotating valve MaterialStainless steel Rotary valvecheck Rotor diameter400mm Rotor width480mm Inletdia. 400mm Inlet flange sizesdia. 540mm Outletdia. 400mm Outlet flange sizesdia. 540mm With motor2,2 KW, 230/400 Volt Rotor speed± 36 Rpm Information Floorspace1,2x0,6 M Total height0,6 MRotating valvesDiscount-Rotary valves > Rotating valvesDiscountBrand > - What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!
General SKU098A526 MakeRPA Aoustin Process Technologies Darnetal TypeNovamix NX-400 Mach.No.891-A Year of construction2002 Pressure Working pressure jacket2 Bar Main Features MaterialStainless steel Volume400 Ltr. Motor30 KW Specified Features - Universal mixer Universal mixer(1x) Capacity400 Ltr Vessel sizesdia. 915x700mm With covercheck Pneumatic operated outletdia. 200mm With jacket(24 Ltr) With motor30,0 KW (Ex) With lump breakercheck With motor5,5 KW, 380 Volt (Ex) MaterialStainless steel 1.4404 (316L) Information LocationBarneveld Floorspace2,5x2,3 M Total height2,6 M Weight3600 KG ATEX compatiblecheckUniversal mixersDiscountRpa AoustinMixers > Universal mixersDiscountBrand > Rpa Aoustin What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are w ...
General SKU023C129 LocationBarneveld Pressure Working pressure6 Bar Vacuum possiblecheck Working pressure vapour evaporator6 Bar Main Features Surface12.5 m2 Specified Features - Falling film evaporator Falling film evaporator(1x) Heating surface12,5 m2 Tube capacity120 Ltr Number of tubes:34 Tube diameter40mm Tube length3000mm Shell capacity210 Ltr Max. temperature140 Degr. C. Capacityvessel 550 Ltr With jacket(coil), Capacity 10 Ltr MaterialStainless steel 1.4571 (316Ti)Falling film evaporatorsDiscountRutzColumns > Falling film evaporatorsDiscountBrand > Rutz What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!
A horizontal flow-wrapping packaging machine Hugo Beck is available. Cycle rate: 5000/h, max. product width: 480mm, max. product height: 150mm, min. product length: 40mm, working height range: 820mm-900mm, max. roll diameter: 400mm, max. roll width: 600mm, roll materials: PO/PE/PP, machine width: approx. 1700mm, weight: approx. 2100kg. Including film folding device FF700-IN, print mark control, seal welding, overlap longitudinal sealing 10mm-30mm, pressure belt and pressure roller. Documentation available. An on-site inspection is possible.
Two heat-resistant flat belt conveyors Integra are available. 1) Center distance: 15200mm, belt length: 15800mm, belt width: 1180mm, overall height: 600mm, belt width: 800mm, max. operating temperature: 130°C, conveying capacity: 30t/h, motor power: 3kW. Including spare edge protection rubber and motor bracket. 2) Center distance: 7500mm, belt length: 8100mm, belt width: 1080mm, overall height: 600mm, belt width: 800mm, max. operating temperature: 130°C, conveying capacity: 30t/h, motor power: 3kW. Including 6× Kito chain hoists. Documentation available. An on-site inspection is possible.
Litz LU 400Year of manuf. : 2016 Control : Heidenhain TNC 640 Speed : 12000 rpmMovement X/Y/Z : 400/350/350 mm____________Description:Spindle:Technology:DirectdriveSpeed:12.000 rpmPower (max.):13 kWTorque (max.):95 NmTaper:SK40NC-Swivelroundtable:B-Axis:-50°/+110°C-Axis:360°C lampingsurface:ø450 mmTableloading (max.):200 kgIn general:Toolmagazine:48 StationsRapid travers in X/Y/Z:48 m/minEquipment/Accessory:Positionsensor:Direct Scales in X/Y/ZChipmanagement:Chip conveyorCoolingmanagement:Internal cooling unit with filter and High-pressure, 30 barWorkpiecemeasurement:Touch probe, Heidenhain TS740Toolmeasurement:Laser, Renishaw NC4 TXSetup operations:Electronic HandwheelFurther Equipment:SpindlechillerFurther Accessory:Misc. used Toolholder
AddUP AddUP BeAM Modulo 400Year of manuf. : 2022 Control : Siemens SINUMERIK ONE NCU 1750 ____________Description:In general:System:Industrial DED systemSafety:Vacuum lock and inert gas purgingYear of manufacture:2022Weight:approx. 7,500 kgGeometry:Number of axes:5-axis kinematics with automatic tool changerTravel ranges (x/y/z):650Ã400Ã400 mmTable diameter:400 mmTable load capacity (max.):100 kgMeasurement:Renishaw probeLasers & Optics:Laser:Dual IPG laserFine machining:500 W (IPG fiber laser, 200 µm fiber)High build-up rate:2000 W (2 kW) (IPG fiber laser, 600 µm fiber)Optics:Precitec YW 30 optics with VX10/VX24 nozzles for standard and micro claddingControl unit:Control:SINUMERIK ONE NCU 1750 (SW 6.14) on a 24 SIMATIC touch panelProcess preparation:Via Siemens NX CAM and edge computing (IPC 427e)Monitoring:Live process control via HMI Display Manager and sensors for t ...
: neu : ca. 4 Monate ab Auftragse : Italien : 218000 € : 400 to : 500 mm : 4.000 x 2.550 mm : 700 mm : 20 mm/s : 2 mm/s : 4000 mm : 4000 mm : 2600 mm : 20500 kg : horizontal verschiebbar : 2550 mm : 1.800 mm : 2.900 mm horizontal movable cylinder hydraulicaly movable stand control by levers as well as control panel according to CE regulations user manual in GERMAN and ENGLISH OPTIONS: Work table, welded to the base frame, with holes on the surface Control panel on the swivel arm (push buttons for press movement, solenoid valves, Siemens CPU) Radio control panel (push buttons for press movement, solenoid valves, Siemens CPU) Siemens control with touchscreen Lifting cylinders in the table (6, 8 or 10 pcs.) No-rotation shaft for the piston 2 speeds for stand movement and cylinder Oil cooler and decompression valve The data for this ad was created with ModulMWS - the software solution of ...
: neu : ca. 12 Wochen ab Auftrags : Türkei : 13760 € : 264.19 € : 0.4 - 2 mm : 400 mm : 300 mm² : 63 mm : 150 m/min : 10 m/s² FESTO pneumatic system SIEMENS servo drive and control system 7’ colour touch screen SIEMENS 2 feed rollers Option: Handwheel and Simlinx remote maintenance module € 4.290,-- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 625 mm y-travel: 650 mm z-travel: 650 mm total power requirement: kW weight of the machine ca.: t required space: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Inv. Num. : 8589 Type: CWK 400D Dynamic Producer: Heckert Created: 2002 Parameters: Control system: Siemens Sinumerik 840D Work table length: 400 mm Work table width: 400 mm Maximum table load (uniform): 400 kg Spindle drive power: 19 kW Number of axes: 4 pieces Tool magazine: 120 pieces Minimum spindle speed: 50 1/min Maximum spindle speed: 15000 1/min X-axis travel: 650 mm Y-axis travel: 650 mm Travel travel Z-axis: 650 mm Cone: HSK A63 Max. tool length: 350 mm Max. tool weight: 10 kg Machine height: 2600 mm Machine length: 8500 mm Machine width: 4500 mm Machine weight: 12000 kg Equipment: 2 pallets 4th axis – rotary table Chip conveyor KNOLL 450 K – 1/250 Emulsion Filtration KNOLL 210/1350 Oil mist extraction
This 4-axis Starrag Heckert Dynamic CWK 400D was manufactured in 2005. It features a Siemens Sinumerik 840D control system, spindle speeds up to 10,000 rpm, and a dual pallet system with rapid 8-second pallet changes. The machine includes a tool magazine with 60 positions and a high-capacity coolant system. Ideal for complex machining tasks. Contact us for more information about this machine.
2025 BIG backhoe bucket 70cm with OQ45 attachment, Technical specifications:, - Weight: 237 kg, - Recording width: 90 cm, - Contents: 388 liters, - CAT 5 - suitable for 5.6 - 9 t excavators
FOR SALE... 2 SETS PROPOLSUION ENGINES CREPELLE 6R 26L CWR & 6R 26L CCWR TO WHOM IT MAY CONCERN; WE VE 2 SETS PROPOLSUION CREPELLE ENGINES AT OUR STOCK PLS FIND ENGINES DETAILS ON BELOW ENGINES CRANKSHAFT IS MARKED WITH STANDARD SIZE CLASS STAMP. TYPE 26L 6R CWR & 6R 26L CCWR POWER 1323kW ENGINE NO. C037 / C045 RPM 810 YOB 1990 WE CAN SELL ENGINE AS COMPLETE OR WE CAN DISMANTLE AND SELL WITH MAJOR PARTS ENGINES EX STOCK. READY TO TRANSPORT. IF YOU'VE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba BEST of regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY
Carbolite CWF 11/5 Chamber Furnace 1100 °C Max Temp: 1100 °C With suction device and table The upward-opening door keeps the hot surface away from the user Gently self-closing door (for 5, 13, 21 & 23 litre models) Standard start-up delay and process timer function Durable alumina backing plates for the heating elements; Robust door frame and base plate High-quality fiber insulation with low thermal mass Powerful heating elements on both sides ensure very good temperature homogeneity Easy access to elements and controls simplify maintenance and servicing More items new and used - you can find them in our shop! International shipping costs on request!
Immediately available used connecting rod
Loma Combination IQ3 metal detector and CW3 check weigher 250 x 90mm aperture. 200mm conveyor width. 360mm weigh pad width. 2100mm machine length. 920mm line height with adjustable feet. M&S Spec machine.
maximum number of results exceeded
please refine your search
