cutter k g used for sale

A gravimetric dosing and mixing unit for plastic granulate Motan is available. Dosing stations: 4, throughput capacity: approx. 150kg/h, reference bulk weight: 0.6kg/dm³, container volume: 4x18l. Machine dimensions X/Y/Z: approx. 600mm/650mm/920mm, weight: approx. 100kg. An inspection on site is possible.

: neu : ca. 8 Wochen ab Auftragse : Spanien : 7570 € : 146.1 € : 50 to : 130 mm : 13/27 mm : 23 1/min : 3 kW : 1100 mm : 900 mm : 1550 mm : 355 kg portable, hydraulic punching machine table with gauge foot pedal user manual in German or English The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

dimensions: ca. 1030 x 1090 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Grain sampler type 1938 DRP, 1 litre sampler, in a wooden case Newly calibrated in 2025, valid until 2029! Complete with tripod (lower part), hollow measure, filling tube, knife, flow weight, scale with tripod and weight tray Weight set (3x200g, 100g, 2x50g, 2x20g, 10g, 5g, 2x2g, 1g, 500mg). Good condition, checked and adjusted by a specialist laboratory. Scales and weights are calibrated only according to customer requirements Operating regulations and official boards are enclosed

Screw compressor Inverter and dryer integrated. 18.50 kW 12.80 bar 3.35 m3/min Year of Make: 2005 Hours: 20,770

Screw compressor Atlas Copco GA22VSD+FF Inverter and dryer integrated 22 kW 12.75 bar 4.51 m3/min Year of Make: 2015 Hours: 19,431

Screw compressor Atlas Copco GR110 110 kW 20 bar 12.60 m3/min Year of Make: 2001 Hours: 44,098

Screw compressor Atlas Copco GR110 110 kW 20 bar 12.60 m3/min Year of Make: 2004 Cjbqey Nl Rmo Da Srwegt Operating hours: 64,326

10432025 Wild Goose Meheen Glass Bottle Filling Line – 2,400 bph (2017) Complete Wild Goose Meheen glass bottle filling system suitable for beer, cider, cocktails, carbonated and non-carbonated soft drinks, kombucha, wine, and other beverages. Filler is in top condition having only about 50 operating hours The nominal capacity is up to 2,400 bottles per hour. The system comprises a Meheen counter-pressure filler with six filling nozzles, crown cap sorter, rinser, two bottle cradling plates for different bottle sizes, ML labeller, inkjet date coder, and a large hopper for crown cap feeding. All Wild Goose Meheen filling systems operate with fully pneumatic processes, with no electric motors, gears, or bearings in the filling mechanism, ensuring high durability and low annual maintenance requirements. The counter-pressure filler is equipped with CO₂ double pre-evacuation to ...

Overview The ABE GLASSPAK 66 is an isobaric filler that is currently in operation and can be viewed. The machine was manufactured by American Beer Equipment (ABE) in the USA in 2018. It has a maximum output of 4,000 bottles per hour for 0.33-liter bottles. The system is designed for 26 mm crown corks and has 18 filling stations. Technical details  Output: 4,000 bottles/hour (for 0.33-liter bottles) Type of closure: 26 mm crown cork Formats: 0.33L Filling stations: 18 Electrical specifications: Max. Voltage: 208-240 V Total current draw: 38.5 A Maximum motor current: 10.6 A Phase: 3-phase Frequency: 60 Hz

GEA Niro Soavi NS2002H Laboratory Homogenizer – 30 L/h – 60 MPa – 2009, The GEA Niro Soavi NS2002H is a compact, high‑pressure laboratory homogenizer designed for R&D, pilot trials and small‑scale production. This 2009 unit is in very good condition and offers a processing capacity of up to 30 L/h (30 dm³/h), depending on product and pressure., With a working pressure up to 60 MPa (600 bar), the NS2002H delivers efficient particle size reduction and stable emulsions, making it ideal for demanding formulations and scale‑up work., Key Features, • Model: GEA Niro Soavi NS2002H, • Year of manufacture: 2009, • Capacity: up to 30 L/h (product and pressure dependent), • Working pressure: up to 60 MPa (600 bar), • Laboratory / bench‑scale design – compact and easy to install in R&D labs, • Stainless steel product contact parts for hygiene and corrosion resistance, � ...

A Fritz Gross pipe end processing machine is available. Connected load: 11kW, max. pipe diameter: 60mm, weight: approx. 1500kg. An on-site inspection is possible.

This 3-axis Okuma Genos L300 E-M was manufactured in 2014. It features a maximum turning diameter of 300 mm and a turning length of up to 1000 mm. The machine is equipped with a spindle speed of up to 3800 rpm and a robust turret with 12 stations. If you are looking to get high-quality turning capabilities, consider the Okuma Genos L300 E-M CNC lathe we have for sale. Contact us for further details.

Equipment Included - Wurster and Dietz OPTIMAT swing-stroke full gate saw, built circa 1970 - Splitting wedge - Cross conveyor - Roller conveyor - Sharpening machine - Setter - Wurster and Dietz Edge Saw FR 7, built circa 1965 Find more here - / Contact us at -

CNC lathe Type: GLS-200 Manufacturer: Goodway Year: 2016 Control: Fanuc Oi - TF Hours: 4851 Max. swing diameter: 500 mm Swivel seat diameter: 310 mm Max. turning diameter: 360 mm Max. turning length: 500 mm Max. load capacity: 85 kg HOWA chuck size: 8" Rod diameter: 65 mm Hole through spindle: 76 mm Spindle bearing diameter: 110 mm Spindle: A2-6 Spindle speed: 45 - 4500 rpm X: 1210 mm Z: 520 mm Turret: 12 positions Tailstock Bar feeder Tool probe Scoop for removing workpiece Machine weight: 3,200 kg Dimensions: 2432 x 1643 x 1727 mm Machine in good condition, fully functional, under power Find more here - / Contact us at -

Two-side evaporator Goedhart -Type: DVS-p-82637 -Cooling capacity: approx. 43 kW -Fin spinning: 7 mm -Fans: 2 x 630 mm -Dimensions: 2600 x 1820 x 750 mm -Volume: 76 L -Weight: 470 kg -Quantity in stock: 1 -Reference number: CH 604 -Condition: Used in good condition, evaporator 100% tight, fans working, ready to work

ABUS Indoor Crane / Overhead Crane – 3,200 kg lifting capacity For sale is a used ABUS indoor crane with a lifting capacity of 3,200 kg. The crane comes from ongoing, productive operation and was used until the end. Robust industrial design with proven technology from ABUS Kransysteme . The crane is ideal for workshop, production, steel construction or warehouse operation. The condition is used, but functional. Regular maintenance was carried out. Technical data: Manufacturer: ABUS Kransysteme Year of Make: 1995 Load capacity: 3,200 kg Wingspan: 8,035 mm Type: (not specified / on request) Control: Pendant button / push button button button (if applicable) Other: The crane comes from ongoing operation and was used until the end. Disassembly by the buyer. Viewing possible by arrangement. Loading can be supported. Sale exclusively to tradespeople. The  ...

Evaporator Goedhart -Type: VRB 82457 -Cooling capacity: 20 kW -Fin spinning: 7 mm -Fans: 2 x 450 mm -Dimensions: 2060 x 900 x 750 mm -Stainless steel housing and block -Electric heating -Volume: 34 L -Weight: 200 kg -Quantity in stock: 1 -Reference number: CH 602 -Condition: Used in good condition, evaporator 100% tight, fans working, ready to work

Evaporator Goedhart -Type: VNS 65407 E -Cooling capacity: 27 kW at -8°C -Fin spinning: 7 mm -Electric defrost -Fans: 5 x 400 mm -Dimensions: 4200 x 800 x 600 mm -Volume: 44 L -Weight: 310 kg -Quantity in stock: 10 -Reference number: CH 598 -Condition: Used in very good condition, evaporator 100% tight, fans working, ready to work

ID3774 MRS 8 cbm – Motorised two-shell grab year/Baujahr 1998 6.5 t 8 cbm Motorised two-shell grab with electro-hydraulic drive 8 cbm Engine Clamshell Grab with Electro-Hydraulic Drive

Evaporator Goedhart -Type: VRB 61507 -Cooling capacity: 14.5 kW -Fin spinning: 7 mm -Fans: 1 x 500 mm -Dimensions: 1460 x 800 x 770 mm -Stainless steel housing and block -Volume: 17 L -Weight: 120 kg -Quantity in stock: 1 -Reference number: CH 601 -Condition: Used in good condition, evaporator 100% tight, fans working, ready to work

Evaporator Goedhart -Type: SRU 81507 -Cooling capacity: approx. 15 kW -Fin spinning: 7 mm -Fans: 1 x 500 mm -Dimensions: 1460 x 930 x 840 mm -Stainless steel housing and block -Electric defrost -Volume: 23 L -Weight: 140 kg -Quantity in stock: 2 -Reference number: CH 600 -Condition: Used in good condition, evaporator 100% tight, fans working, ready to work

Conveyor belt Venjakob Type Belt Conveyor Belt Year of manufacture 1987 Conveyor belt width 1300 mm Support length 4800 mm Motor drive 0.55 kW Dimensions outside Length 5000 mm x Width 1700 mm x Height 950 mm Weight 670 kg

General SKU425W1345 LocationBarneveld CEcheck MakePosimat Main Features MaterialStainless steel Motor14 KW Specified Features - Miscellaneous MaterialStainless steel Capacity166 bottles/min Motor14 kW, 400 volt Capacity0,70-3 l. Information TypePosiflex-35-VA-Giramat-E Mach.No.11627.3.01 Year of construction2010 Floor space4,10x4,00 m Total height2,55 m Weight6000 kg Extra Specifications20-fold bottle unscrambler. Siemens toucscreen control, type Simatic panel, With vacuum conveyor. size conveyor 4000x1300mm. Sodeca fan, left side output possible bottle sizes 0,70-3 l., : Sorting mono, pressure 6 bar, : DairyOther feedMiscellaneousPosimatIndustries > Food & Feed > DairyIndustries > Food & Feed > Other feedMiscellaneous > MiscellaneousBrand > Posimat What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for ...

General SKU080A390 MakeGiusti & Son Ltd TypeLabomix - MKII No.J-10942.A Year of construction1990 LocationBarneveld Material Product contact materialStainless steel 1.4306 (304L) Pressure Working pressure0 Bar Vacuum possiblecheck Working pressure jacket3 Bar Main Features MaterialStainless steel Volume15 Ltr. Motor0.37 KW Specified Features - Stirring vessel Closed stirring vesselcheck Capacity15 l. Vessel sizesø 295 mm x 470 mm Hollow bottomcheck Dished top sidecheck With covercheck Top connectionscheck Outlet25 mm With jacketcheck Max. temperature130 °C With anchor stirrercheck with scrapers Motor0,37 kW, 240/415 Volt (Ex) Speed mixing shaft28 rpm MaterialStainless steel 1.4306 (304L) Information With switchgearcheck Floorspace0,8 x 0,6 m Total height1,4 m Weight300 kg ATEX compatiblecheck Extra Specificationswith vacuum pump. 0,26 kW, 240/415 V ...

General SKU132X770 MakeEberhard Hoesch & Söhne, Düren TypeGK6/3500/SO No.32 6333 Year of construction1988 LocationBarneveld Main Features MaterialHastelloy Volume3500 Ltr. Motor9.2 KW Specified Features - Stirring vessel MaterialStainless steel 2.4610 (Hastelloy C-4) Open stirring vessel(1x) Capacity3500 Ltr Vessel sizesdia. 1800x1300mm Dished bottomcheck Flat top sidecheck With covercheck Manhole800x450mm Outletdia. 175mm With jacketcheck With propellor stirrerHoesch Gegenstromrührer With gate type stirrercheck Motor9,2 KW + 7,5 KW, 380/660 Volt Speed mixing shaftvariable (12-49 prop./ 21-87 Rpm gate)DiscountStirring vesselsHoeschDiscountStirring vessels > Stirring vesselsBrand > Hoesch What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome ...

Manufacturer: Gurki Model: GPS-5030LW Year of Manufacture: 2021 Type of Machine : Angle welding machine Frequency: 50 Hz Phase: 3 Power: 15 kW CE Certified Find more here - / Contact us at -

Manufacturer: Gurki Model: GPL-5545DI Year of Manufacture: 2023 Type of Machine : Angle welding machine CE Certified Voltage: 400 V Frequency: 50/60 Hz Phase: 3 Power: 3 kW Find more here - / Contact us at -

A Gernep self-adhesive labeling machine is available. Nominal capacity: 2500bottles/h, running direction: RM, throughput capacity control range: 800-3000bottles/h, container format 1 diameter/height: 66mm/280mm, container format 2 diameter/height: 85mm/316mm, container volume 1/2: 500ml/1000ml, label dimensions X/Y: 160mm/17mm, label application: U-seal, conveyor height: 1000mm. Including self-adhesive dispenser unit and swing-top closure alignment. Documentation vorhanden. An on-site inspection is possible.

A cold-glue labeling machine Gernep is available. Direction of travel: LM, nominal output: 5000bottles/h, control range: 1000-5500bottles/h, gluing height: 330mm, bottle format height range: 297mm-350mm, bottle format diameter range: 74mm-89mm, bottle material: glass, bottle volume: 0.75/1l, bottle content: wine, application: body/neck ring label/back label. Cold-glue format 1: label length range: 25mm-160mm, max. label height: 150mm, max. label height bottom edge/top edge: 15mm/320mm. Cold-glue format 2: min. label length: 25mm, max. label height: 115mm, max. label height bottom edge/top edge: 15mm/130mm. Including dating, optical orientation, upper-part height adjustment, glue pump and two cold-glue units. Documentation available. An on-site inspection is possible.

A cold-glue labeling machine Gernep, which was used in the food industry, is available. Nominal output: 10000bottles/h, running direction: LM, control range: 2000-12000bottles/h, gluing height 1/2: 330mm/230mm, bottle format height 1/2: 307mm/260mm, bottle format diameter 1/2: 90mm/68mm, bottle material: glass, bottle type: VDF/NRW, bottle volume: 1000ml/500ml, application: body label/neck label/back label, container condition: hot. Cold-glue format 1: label length range: 25mm-140mm, max. label height: 150mm, label height lower edge/upper edge: 15mm/320mm. Cold-glue format 2: label length range: 25mm-140mm, max. label height: 150mm, label height lower edge/upper edge: 15mm/220mm. Including two cold-glue units, dating, sensor label inspection, breakage detection, overload clutch, additional accumulation switch and center slide. Documentation available. An on-site inspection is possible.

A Gernep cold glue labeling machine that has been used in the brewery industry is available. Rated capacity: 5000bottles/h, direction of operation: LM, control range: 1000-6000bottles/h, glue application height: 330mm, bottle material: glass, bottle volume: 330ml/500ml, min. label length range: 25mm-130mm, max. label height: 130mm, max. label height lower edge/upper edge: 15mm/320mm, application: swing-top label/body label. Including cold glue unit, prepared wet glue unit, date coding, height adjustment, overload clutch, infeed and outfeed tunnel and foot extension with floor plate. Documentation available. An on-site inspection is possible. Expected to be available from the end of May 2026.

Rated output: 5000bottles/h, running direction: LM, control range: 1000-6500bottles/h, bottle material: PET/glass, bottle format volume: 200ml/250ml/400ml/500ml/750ml/1000ml/1200ml, glass bottle height range: 59mm-121mm, glass bottle diameter: 65mm/70mm, application: neck ring label/body label/back label/wraparound label. Including three self-adhesive dispensers, height adjustment, central lubrication, breakage detection, bottle counter, clamp stars, swivel arm and Etima hot glue for Rollina and neck ring. Documentation available. An on-site inspection is possible.

A Gernep cold glue and self-adhesive labeling machine is available. Rated capacity: 8000bottles/h, direction of rotation: clockwise, control range: 1400-9000bottles/h, bottle format volume: 700ml, tamper-evident label: available, bottle formats: 10, bottle contents: spirits, application: neck ring label/body label/back label/tamper-evident label, including optical label inspection, date coding, self-adhesive dispenser, two cold glue units, bottle counter and two different bottle locks. Documentation available. An on-site inspection is possible.

bore capacity in steel (diameter): 32 mm throat: 325 mm bore stroke: 170 mm taper MK: 4 MK table-size: 570 x 480 mm feeds: 0,1 - 0,16 - 0,25 mm/U turning speeds: 60 - 1600 U/min total power requirement: 2,9 KW weight of the machine ca.: 0,65 t dimensions: 1,2 x 0,8 x 2,15 m Pillar drilling machine with: - Feed - Variable spindle speed - Coolant pump - Machine light The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 32 mm throat: 325 mm bore stroke: 170 mm taper MK: 4 MK table-size: 570 x 480 mm feeds: 0,1 - 0,16 - 0,25 mm/U turning speeds: 60 - 1600 U/min total power requirement: 2,9 KW weight of the machine ca.: 0,65 t dimensions: 1,2 x 0,8 x 2,15 m Pillar drilling machine with: - Feed - Variable spindle speed - Coolant pump - Machine light The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 290 mm, 450 mm, 5000 1/min

Control: EPL Country of origin: Germany Spindle passage: Ø65 mm Tool turret: 12-fold driven places Tool holder: VDI 40 Speed tools: 3000 rpm Weight: approx. 4,700 kg + 600kg control cabinet Chip conveyor: BMF Bürener Maschinenfabrik Bar feeder: GIOVANNI CUCCHI, type DB 70 Tools for an extra charge There are a total of 6 machines with bar feeder (price per machine with loader) Dcjwvey N Tdzeu Nu Ieg There is 1 machine without loader available (€ 8.500,-)

Non Returnable High-Speed Glass Bottle Beer Filling & Packaging Line General Overview High-capacity and fully integrated beer bottling and packaging line designed for efficient processing of multiple glass bottle formats and packaging configurations. The line combines advanced automation, hygienic construction, and world-class machinery from leading manufacturers to ensure maximum performance, flexibility, and reliability. Key Production Capacities Nominal Speed (Bottles per Hour) 25 cl: 40,000 bottles/hour 33 cl: 35,000 bottles/hour 50 cl: 30,000 bottles/hour Bottle Formats 25 cl 30 cl 33 cl 50 cl Packaging Formats 25 cl Formats 4 x 6 x 25 cl 1 x 12 x 25 cl 24 x 25 cl 30 cl Formats 24 x 30 cl 33 cl Formats 4 x 6 x 33 cl 6 x 4 x 33 cl 1 x 12 x 33 cl 24 x 33 cl 50 cl Formats 20 x 50 cl Line Characteristics & Features Design & Engineering Transparent See Th ...

Manufacturer: Fikara Type of Machine : Galvanizing Rack System Technical Specifications - Year of Manufacture: 2000 - Year of Overhaul: 2018 - System Type: CE-1 - Heating System - Heating Output: 28 kW - Heating Medium: 3 x 400V, 50 Hz - Nominal Temperature: 70 degrees C - Nominal Current: 40.5 A - Ventilation System - Air Flow Rate: 17,500 m3/h - Motor Output: 6 x 0.55 kW - Voltage: 230/400 V - Nominal Current: 5 x 1.55 A The steel structure is no longer there Find more here - / Contact us at -

Manufacturer: Gildemeister Model: GMX 400 linear Year of Manufacture: 2007 Total Power Requirement: 100 kVA Voltage: 400 V Machine Weight: 24,000 kg Floor Space Required: 60 m2 Working Range - Centre height: 1,343 mm - Maximum turning diameter: 640 mm - Maximum turning length: 1,930 mm - Maximum turning length over bed: 550 / 180 mm - Slide travel longitudinal X1, X2: 1,585 / 1,400 / 1,500 mm - Slide travel vertical Y: plus/minus 110 mm - B-axis: plus/minus 120 degrees - Maximum circumference: 640 mm - Length of workpiece in crown area: not specified - Maximum workpiece weight: not specified Spindle Specifications - Spindle head flat flange DIN: Flachflansch - Spindle nose diameter front bearing: 220h5 mm - Spindle bore diameter: 107 mm - Spindle nose diameter: 150 mm - Max. chuck bore diameter in front bearing: 250 / 315 / 400 mm (internal taper) - Spindle speed HSP: 3,200 / 4 ...

Electric chain hoist, crane, overhead crane, assembly crane, manual trolley, trolley, trolley drive, crane drive, crane travel, trolley -Manufacturer: Abus, electric chain hoist with driven chassis -Chain hoist: Abus type GM3- Load capacity 1000 kg -Main stroke: 5 m/min -Fine stroke: 1.3 m/min -Chain length: 3.5 m -Electric chassis: Abus S11148 34/153 rpm -Beam width: max. 310 mm Dimensions: see photo and technical drawing -Electrical accessories: Connection cable (see photos) -Transport dimensions: 450/780/H400 mm -Weight: 56 kg

This APV Gaulin 1056 MC 18-5TPSC aseptic homogeniser is a 3-cylinder machine which is designed for ± 4.500 liter per hour with a maximum pressure of 345 bar. The homogensier is equipped with 2-stages with puppet valve cylinder, both stages manual controlled. Manometer. Motor: 45 kW - 380 V - 98 Amp - 50 Hz - 1.465 rpm. Stainless steel cladded. Oil pumping system outside the machine., Type of Machine: Homogeniser, Capacity: 4.500 liter per hour, Stages: 2 Stages, Max. Pressure: 345 bar, Valve cylinder: Puppet valves, Product: Dairy, Piston diameter: 44 mm, Motor: 45 kW - 380 V - 98 Amp - 50 Hz - 1.465 rpm, Dimensions: 180 x 110 x 180 cm, Weight: 2.115 kg

: neu : ca. 8 Wochen ab Auftragse : Spanien : 12100 € : 232.32 € : 45 to : 175 mm : 4 : 27 x 12 mm : 15 mm : 16 1/min : 300x10 / 200x13 mm : 80x80x8 mm : 7 mm : 2.2 kW : 1360 mm : 1100 mm : 1500 mm : 800 kg 4 working stations foot pedal hydraulically driven oil filled table at punching and notching station with gauge user manual in GERMAN and ENGLISH The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This 3-axis Gildemeister CTX 400 Serie 2 was manufactured in 2002. It features a spindle speed of up to 5,000 rpm and a z-axis travel of 635 mm, along with an x-axis travel of 570 mm over the bed. The machine includes a 12-position turret and is equipped with a 3-jaw chuck, chip conveyor, and coolant system. If you are looking to get high-quality turning capabilities, consider the Gildemeister CTX 400 Serie 2 machine we have for sale. Contact us for further details.

CNC Swiss lathe GILDEMEISTER SPRINT 20/8 linear With Fanuc 31i controller Year of Make: 2016 Spindle bore: 20 mm MAIN SPINDLE Turning diameter: max. 20 mm Speed range : max. 10000 rpm Stroke Z1: 80 mm SUB-SPINDLE Turning diameter: max. 20 mm Stroke Z 2 : 300 mm Speed: max. 10000 rpm SLIDE 1 Stroke X 1: 50 mm Stroke Y 1: 350 mm 6 Pos. Tool Holder 12 x 12 5 rotating tools including spindles with clamp holder ESX 16 SLIDE 2 Stroke x 2 : 240 mm 4 position tool holder for external machining with connection 12 x 12 4 position tool holder for internal machining diameter 20 mm 5 rotating tools including spindles with clamp holder ESX 16 6 + 2 axes, 2 Y axes as standard Linear actuator for maximum precision With the following accessories: Full protection cab with interior lighting Various tool holders C axis for main and counter spindle Bar Feeder L ...

Overview    The Meheen M6 isobarometric filler from the American manufacturer Wild Goose was built in 2020. The machine was used very little.  Technical Details  Capacity: Up to 2.160 bottles per hour   Number of filling heads: 6   Last used formats: 0,33l Longneck   Possible bottle diameter: 5.3 cm - 7.6 cm  Dimensions (Floor): 1680 mm x 1070mm 

CNC Swiss lathe GILDEMEISTER SPRINT 20/8 With Fanuc 32i control Year of manufacture: 11/2019 Spindle bore: 20 mm MAIN SPINDLE Turning diameter: max. 20 mm Speed range : max. 10000 rpm Stroke Z1: 60 mm SUB-SPINDLE Turning diameter: max. 20 mm Stroke x 2 : 220 mm Stroke Z 2 : 170 mm Speed: max. 10000 rpm SLIDE 1 Stroke X 1: 50 mm Stroke Y 1: 325 mm SLIDE Y 2 Stroke Y 2 : 85 mm With the following accessories: Full protection cab with interior lighting Various tool holders Tool holder for slides 1-3 4 driven tools with 4 spindles with ESX/ER 16 holder C axis for main and counter spindle Y axis on carriage 1 – 2 2 cross slides Workpiece unloading conveyor Signal light 4 colour Fire extinguishing system Coolant device 165 l ( Pumping capacity 90 l/min 1 bar) THE MACHINE IS IN MINT CONDITION THE MACHINE HAS ONLY 110 PROGRAM RUNNING HOURS

: neu : ca. 12 Wochen ab Auftrags : Italien : 57900 € : 1094.31 € : 1 : 650 mm : 0,5 - 170 mm : 670 x 2200 mm : 4000 m³/h : 120 mm : 6 bar : 78 (+/-2) dB : 22 kW : 2600 mm : 1350 mm : 2100 mm : 1125 kg WITH 2 WORKING STATIONS: 1 X GRINDING BELT UND 1 X BRUSH UNIT ON TOP Machine made of stress-free welded steel construction for stable and rigid structure. Work table with motorised height adjustment via 4 synchronised spindles. Independent drive motors for each work group. Hoods for extraction inside the machine, one per station. Touch screen for -Automatic star-delta connection of the main motors - Analogue ammeter for each group - Digital display for sheet thickness with decimal point tolerance - Material thickness adjustment (+/- 0.1 mm) - Machine condition monitoring with alarm messages FEEDING SYSTEM Robust steel structure, wear-resistant surface. Vacuum conveyor belt on request  ...

Rotary Lobe Blower High Vacuum Blower Unused Manufacturer: Aerzener Maschinenfabrik GmbH Type: GLB 17.14 Year: 1977 Volume flow: 100 m³/min P1: 1.0 atü (bar) P2: 0.5 atm (bar) ΔH: 5 mWS (0.5 bar) at 100 kW and 890 rpm Dimensions approx. 1500 x 1000 x 1100 mm Areas of application: central dust extraction, vacuum coating, packaging industry, chemical processes, steel degassing Changes and errors in the technical data, specifications and prices as well as prior sale reserved.

Key data: 500 KG, 800 mm, 190 mm

Shelving System Spare Parts Storage High Rack, Storage Rack, Industrial Rack Used Manufacturer: GEMAC Shelving unit single-row approx. 12.7 m Height approx. 1.9 m Depth approx. 0.8 m 12 fields with 6 compartments each Bay load max 500 kg each Shelf load max 80 kg each each compartment consists of 2 sheet metal shelves 105 x 40 cm Total weight approx. 770 kg The shelves have been dismantled Changes and errors in the technical data, specifications and prices as well as prior sale reserved.