counter used for sale

cutting diameter: 450 mm saw band length: 5400 x 41 x 1,3 mm cutting width: 695 mm : 425 x 425 mm Capacity 90° rectangular: 560 x 425 mm capacity 45 degrees: round: 430 mm : 425 x 425 mm Capacity 45° rectangular: 430 x 425 mm : 450 mm : 425 x 425 mm : 560 x 425 mm capacity 60 degrees: round: 320 mm capacity 60 degrees: square: 290 x 290 mm capacity 60 degrees: flat: 260 x 425 mm table height: 690 mm speeds steplessly adjustable: 20 - 100 m/min dimensions of saw-blade: 5400 x 41 x 1,3 mm total power requirement: 4,67 kW weight of the machine ca.: 1,63 t dimensions of the machine ca.: 2,85 x 1,3 x 1,8 m Horizontal band saw with linear guideways, ideal for mitre cuts between 90° and +30°. Auto height adjustment sensors ensure that the bow can approach the material at high speed. The hydraulic cutting control allows the bow rise up again after a cut has been made. This process is control ...

sheet width: 2050 mm plate thickness: 4 mm table-size: 530 x 830 mm table height: 830 mm back stop - adjustable: 750 mm no. of strokes: 29 Hub/min total power requirement: 7,5 kW weight of the machine ca.: 1600 kg dimensions of the machine ca.: 2,63 x 2,20 x 1,28 m Basic equipment: - Engine. Behind stop with NC control and 750 mm adjustment - 1000 mm long measuring stop with T-slot and stopper - Foot pedal with emergency stop switch - Arm in front for material - Cutting line lighting - Hand and foot protection front and rear - piece counter Options: - Pneumatic lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° All other sizes can be found on the RS-Sperling Website. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1550 mm plate thickness: 5 mm cutting angle: 2,5 ° table width: 530 mm table height: 830 mm back stop - adjustable: 750 mm no. of strokes: 29 Hub/min total power requirement: 7,5 kW weight of the machine ca.: 1350 kg dimensions of the machine ca.: 2,13 x 2,20 x 1,28 m Basic equipment: - Engine. Behind stop with NC control and 750 mm adjustment - 1000 mm long measuring stop with T-slot and stopper - Foot pedal with emergency stop switch - Arm in front for material - Cutting line lighting - Hand and foot protection front and rear - piece counter Options: - Pneumatic lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° All other sizes can be found on the RS-Sperling Website. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1.550 mm plate thickness: 3 mm cutting angle: 2,5 ° table width: 510 mm table height: 820 mm back stop - adjustable: 600 mm no. of strokes: 35 Hub/min total power requirement: 3 kW weight of the machine ca.: 1600 kg dimensions of the machine ca.: 2,14 x 2,06 x 1,21 m Basic equipment: - manual backgauge with 600 mm travel - Measuring stop 800 mm - Foot pedal with emergency stop switch - Bracket arms in front for workpieces - Cutting line lighting - Protective demarcation OPTIONS: - Pneumatic sheet metal lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° - engine. Backgauge with NC control and 750 mm travel - engine. Backgauge with NC control and 1000 mm travel - piece counter All other sizes can be found on the RS-Sperling Website. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2550 mm plate thickness: 4 mm cutting angle: 1,3 ° table width: 530 mm table height: 830 mm back stop - adjustable: 750 mm no. of strokes: 29 Hub/min total power requirement: 7,5 kW weight of the machine ca.: 1900 kg dimensions of the machine ca.: 3,13 x 2,20 x 1,28 m Basic equipment: - Engine. Behind stop with NC control and 750 mm adjustment - 1000 mm long measuring stop with T-slot and stopper - Foot pedal with emergency stop switch - Arm in front for material - Cutting line lighting - Hand and foot protection front and rear - piece counter Options: - Pneumatic lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° All other sizes can be found on the RS-Sperling Website. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CNC – controlled frame gluing press for automatic gluing of all frame constructions with dowel connection – tine connection – 45° miter connection, automatic centering of the press plates and the upper press beam. The frame presses are available in the following sizes – pressing area 3,000 x 1,700 mm – 3,000 x 2,000 mm and 3,500 x 2,500 mm. Two vertical press cylinders – pressing force per cylinder 7 tons (optional four vertical press cylinders). Two horizontal press cylinders, stroke range 150 mm - pressing force per cylinder 3 tons. Maximum tread depth 130 mm (larger tread depths on request). CNC control from SIEMENS® with touch screen for calling up three automatic pressing cycles, 99 compression programs can be stored per pressing cycle. Among other things, the following parameters can be programmed: frame size, frame profile structure, pressing time, pr ...

Spindle swivel: Yes -45 to 45Â; Height adjustment: electric; Swivel adjustment: electric; Stop adjustment: manual; Height display: digital; Swivel angle indicator: digital; Milling stop indicator: mechanical counter; Spindle diameter: 30 mm; Speeds: 3000, 4500, 6000, 8000, 10000 rpm; Power consumption: 7 kW; Engine braking: Yes, automatic; Suction port: 1 x 120mm, 2 x 80mm; Machine length: 2500mm; Machine width: 1250mm; Weight: 510kg; Stable steel-grey cast iron construction Dynamically balanced milling unit anchored to the work table Particularly robust construction Smooth running thanks to precision units and high dead weight Standard with clockwise-counterclockwise rotation and electronic locking when changing direction 5 Speeds from 3000 - 10000 min ̄¹ Speed change is easy and convenient from the machine side Standard with MK 4 interchangeable spindle system La ...

sheet width: 1350 mm plate thickness: 6 mm cutting angle: 2,5 ° table width: 530 mm table height: 830 mm back stop - adjustable: 750 mm no. of strokes: 29 Hub/min total power requirement: 7,5 kW weight of the machine ca.: 2150 kg dimensions of the machine ca.: 2,2 x 1,93 x 1,28 m Basic equipment: - Engine. Behind stop with NC control and 750 mm adjustment - 1000 mm long measuring stop with T-slot and stopper - Foot pedal with emergency stop switch - Arm in front for material - Cutting line lighting - Hand and foot protection front and rear - piece counter Options: - Pneumatic lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° All other sizes can be found on the RS-Sperling Website. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 460 mm saw band length: 5200 x 41 x 1,3 mm cutting width: 470 mm : 460 mm Capacity 90° rectangular: 470 x 460 mm cutting speed: 20 - 100 m/min total power requirement: 5,2 kW weight of the machine ca.: 1,66 t dimensions of the machine ca.: 3,1 x 3,1 x 1,8 m Fully automatic band saw for cutting solid material, tubes and profiles of steel, cast-iron, light and non ferrous materials, at 90°. Entirely made of steel. The rear jaw of the hydraulic vice has a number of hardened rollers that are turned by an electric motor. The front jaw consist of a number of free running rollers. Once the work piece is clamped between the rollers no further clamping is needed. The material is fed through the vice to the material stop which contains a micro-switch controlling the feed motor. A counter controls the number of cuts. Should the blade brake the machines stop automatically. The ma ...

sheet width: 1.350 mm plate thickness: 3 mm cutting angle: 2,5 ° table width: 510 mm table height: 820 mm back stop - adjustable: 600 mm no. of strokes: 35 Hub/min total power requirement: 3 kW weight of the machine ca.: 1350 kg dimensions of the machine ca.: 2,6 x 1,94 x 1,21 m Basic equipment: - manual backgauge with 600 mm travel - Measuring stop 800 mm - Foot pedal with emergency stop switch - Bracket arms in front for workpieces - Cutting line lighting - Protective demarcation OPTIONS: - Pneumatic sheet metal lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° - engine. Backgauge with NC control and 750 mm travel - engine. Backgauge with NC control and 1000 mm travel - piece counter More sizes at info @ rs-sperling .de The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2050 mm plate thickness: 6 mm cutting angle: 1,5 ° table width: 530 mm table height: 830 mm back stop - adjustable: 750 mm no. of strokes: 29 Hub/min total power requirement: 7,7 kW weight of the machine ca.: 3100 kg dimensions of the machine ca.: 2,2 x 2,63 x 1,28 mm Basic equipment: - Engine. Behind stop with NC control and 750 mm adjustment - 1000 mm long measuring stop with T-slot and stopper - Foot pedal with emergency stop switch - Arm in front for material - Cutting line lighting - Hand and foot protection front and rear - piece counter Options: - Pneumatic lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° All other sizes can be found on the RS-Sperling Website. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1.050 mm plate thickness: 3 mm cutting angle: 2,5 ° table width: 510 mm table height: 820 mm back stop - adjustable: 600 mm no. of strokes: 35 Hub/min total power requirement: 3 kW weight of the machine ca.: 1.100 kg dimensions of the machine ca.: 2,06 x 1,64 x 1,21 m Basic equipment: - manual backgauge with 600 mm travel - Measuring stop 800 mm - Foot pedal with emergency stop switch - Bracket arms in front for workpieces - Cutting line lighting - Protective demarcation OPTIONS: - Pneumatic sheet metal lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° - engine. Backgauge with NC control and 750 mm travel - engine. Backgauge with NC control and 1000 mm travel - piece counter More sizes at info @ rs-sperling .de The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

4 pcs. rope pulleys for counter weight of a FB 225 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

4 pcs. rope pulleys for counter weight of a FB 225 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 150 mm gear width: 42 mm max. module: 3 min. module: 0,5 total power requirement: 10 kW weight of the machine ca.: 6 t External gears, max. Ø 150 mm (or more) Internal gears, max workpiece Ø, approx. 280 mm Gear width, max. 42 mm Module, max. 0.5 - 3 Length of stroke 0 - 50 mm Adjustment of stroke 0 - 70 mm Distance between shaper spindle and body of machine 250 mm Spindle internal table, approx. 45 mm Strokes, roughing / finishing 450 - 1,250 / 2,500 / min Table Ø 250 mm Table bore 100 mm Distance between table and shaper head, approx. 320 mm Axial travel of workpiece slide, approx. 285 mm Feed range, tooth depth 0.01 - 0.063 mm/stroke Rotary feed 0.125 - 3,150 mm/stroke Total electrical load, approx. 10 kW - 380 V - 50 Hz Weight 6,000 kg Accessories / Special Features Built-in hydrostatic straight guide. Built-in raiser plate for raising the shaper head 130 m ...

max. wheel diameter: 265 mm gear width: 45 mm max. module: 4 min. module: 0,3 max. workpiece diameter: 300 mm stroke length max.: 0-50 mm stroke position adjustment: 25 mm distance work spindle /surface of the table: 170/245 mm spindle taper: innen MK 4 table-size: 180 mm table hole: 95/75 mm strokes per minute: 450 - 840 total power requirement: 10 kW weight of the machine ca.: 5200 kg dimensions of the machine ca.: m : : : : : : : Max. gear Æ (external) approx. 265 mm Max. workpiece Æ for internal gears 300 mm Max. gear width 45 mm Module range 0.3 - 4 Length of stroke 0 - 50 mm Adjustment of length of stroke 25 mm Distance between table and spindle, min./max. 170/245 mm Spindle taper (external 90 / internal 50) MT 4 Table size 180 mm Table bore 95 / 75 m ...

Format range: max. 1350 mm, min. 45 mm Equipment: Longitudinal seam, folding bottom, double edge, 4 + 6 point gluing, HHS electronic finishing unit, 4 channel with 4 application heads, High pressure, disc gluing unit left, electronic Overhaul folding with servos, extended folding station, module 150, Primary crusher right and left, kicker, counter, vibrator on the jetty, digital position indicator, motorized threading station, motorized Transfer station, additional means transport in folding, vacuum on Overturning, camera surveillance, Jagenberg DBS 01 control, fully automatic format setting Jagset II, pneumatic, clocked Press strip. Overhaul 2023: cleaned, checked, painted and with new feeder and transport belt. Other: The machine can be viewed while running by appointment.

max. wheel diameter: 400 mm gear width: 500 mm max. module: 15 min. module: 0,5 total power requirement: 2,5 kW weight of the machine ca.: 2 t dimensions of the machine ca.: m H O E F L E R (Germany) CNC Controlled 4 Axis Inspection Centre for Gears Model EMZ 400 Year 1988 Serial No. 067 047 ____________________________________________________ Working range: Min./max. gear Ø / base circle Ø 0 – 400 / 390 mm Module range 0.5 – 15 Gear width, max. 500 mm Travel of measuring head, approx. +/- 180 mm Helix angle 0 – 60 ° Max. weight of workpiece, approx. 250 kg Distance between centres, approx. 1,000 mm Distance between centre and body of counter steady 205 mm Table Ø, approx. 290 mm Plotter diagram scales 50 / 1 ...

cutting diameter: 320 mm saw band length: 4670 mm cutting width: 580 mm total power requirement: 7,4 kW weight of the machine ca.: 3 t Sawing range, circular, max. 100 - 320 mm vertical, max. 100/100 x 320/460 mm Length of cut, min./max. 0 - 580 mm Distance from column to saw band, max. 690 mm Cutting speed, infinitely variable 16 - 160 m/min Dimensions of saw band, length x Ø approx. 4,670 x 38 mm Length of remaining pieces, automatic/single cut 100/10 mm Saw blade drive, approx. 4.4 kW Total electrical load, approx. 7.4 kW - 380 V - 50 Hz Weight, approx. 3,000 kg Accessories / Special Features: Infinitely variable speeds of saw blade motor via servo motor and STOEBER drive. Display of cutting speed on control panel. Infinitely variable settings of sawing feed with display of the current cutting speed. Workpiece counter: Number of workpieces can be preset. Selection swi ...

Format range: max. 1000 mm, min. 126 mm Equipment: Longitudinal seam, folding bottom, double edge, electronic top gluing unit HHS X-tend, 4 channel with 2 application heads, Disc gluing unit left, feeder with vibrator, folding floor module A2 Primary crusher right and left, kicker, counter, Bobst CUBE control, additional middle transport at the top/bottom in folding, cutting alignment on the press belt, pneumatic, intermittent press belt. Overhaul 2023: cleaned, tested, painted and fitted with new feeders and Transport belts, as well as equipped with new press belts. Other: The machine can be viewed while running by appointment.

cutting diameter: 380 mm saw band length: 4800 x 34 x 1,1 mm cutting width: 430 mm : 380 mm Capacity 90° rectangular: 430 x 380 mm speeds steplessly adjustable: 20 - 100 m/min total power requirement: 4,2 kW weight of the machine ca.: 1,34 t dimensions of the machine ca.: 2,9 x 0,95 x 1,66 m Fully automatic band saw for cutting solid material, tubes and profiles of steel, cast-iron, light and non ferrous materials, at 90°. Entirely made of steel. The rear jaw of the hydraulic vice has a number of hardened rollers that are turned by an electric motor. The front jaw consist of a number of free running rollers. Once the work piece is clamped between the rollers no further clamping is needed. The material is fed through the vice to the material stop which contains a micro-switch controlling the feed motor. A counter controls the number of cuts. Should the blade brake the machines stop auto ...

sheet width: 3050 mm plate thickness: 2,0 mm cutting angle: 1,5 ° table width: 530 mm table height: 820 mm back stop - adjustable: 600 mm no. of strokes: 35 Hub/min total power requirement: 4 kW weight of the machine ca.: 2300 kg dimensions of the machine ca.: 3,64 x 2,06 x 1,21 m Basic equipment: - manual backgauge with 600 mm travel - Measuring stop 800 mm - Foot pedal with emergency stop switch - Bracket arms in front for workpieces - Cutting line lighting - Protective demarcation OPTIONS: - Pneumatic sheet metal lifting device - Optical safety bar - Miter device with adjustable - angle 0-180 ° - engine. Backgauge with NC control and 750 mm travel - engine. Backgauge with NC control and 1000 mm travel - piece counter More sizes at info @ rs-sperling .de The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Double-spindle machining center with swivel axis One side 5.axes with swivel bridge and rotary tables. One side 4th axis, without swing bridge, 5th axis prepared. Workspace x-axis 400 mm y-axis (tool change position) 450 (700) mm z-axis 400 mm Swivel beam/counter bearing with face toothing ----- Number of spindles 2 Spindle spacing 400 mm Spindle speeds up to 17,500 rpm Power 40/ 100% ED 25/ 18 KW ----- Feed/rapid traverse 50,000 mm/min Tool magazine 2 x 60 tool slots Tool holder HSK 63 Equipment: - Expansion of the tool magazine to 2 x 60 tool positions per spindle - Oil distributor for NC rotary table - 5.Axis for one side - Extension of machine hydraulics - Increased clamping pressure to 250 bar - Connection to central coolant system - IKZ 70 bar - Automatic loading door - Pneumatic support control - Flushing package - Tool life monitoring -Probe - Art ...

cutting diameter: 560 mm saw band length: 6000 x 41 x 1,3 mm cutting width: 570 mm : 560 x 560 mm Capacity 90° rectangular: 570 x 560 mm speeds steplessly adjustable: 20 - 100 m/min total power requirement: 6,0 kW weight of the machine ca.: 2,24 t dimensions of the machine ca.: 3,5 x 1,05 x 2,05 m Fully automatic band saw for cutting solid material, tubes and profiles of steel, cast-iron, light and non ferrous materials, at 90°. Entirely made of steel. The rear jaw of the hydraulic vice has a number of hardened rollers that are turned by an electric motor. The front jaw consist of a number of free running rollers. Once the work piece is clamped between the rollers no further clamping is needed. The material is fed through the vice to the material stop which contains a micro-switch controlling the feed motor. A counter controls the number of cuts. Should the blade brake the machines sto ...

cutting diameter: 440 mm saw band length: 5200 mm cutting width: 695 mm : 440 mm Capacity 90° rectangular: 610 x 440 mm : 4409 x 440 mm capacity 45 degrees: round: 410 mm : 440 x 440 mm Capacity 45° rectangular: 410 x 440 mm : 440 mm : 440 x 440 mm : 500 x 440 mm capacity 60 degrees: round: 320 mm capacity 60 degrees: square: 250 x 250 mm capacity 60 degrees: flat: 250 x 440 mm table height: mm band speed: stufenlos 20-100 m/min total power requirement: 3,62 kW weight of the machine ca.: 1,54 t dimensions of the machine ca.: 2,8 x 1,21 x 1,87 m Horizontal band saw with linear guideways, ideal for mitre cuts between 90° and +30°. Auto height adjustment sensors ensure that the bow can approach the material at high speed. The hydraulic cutting control allows the bow rise up again after a cut has been made. This process is controlled by digital counter on the control panel. The bow angle ...

Riggs twin head depositor Model: 1000 Serial: TT1310 2011, twin head depositor, previously used for filling food grade oils 10l - 25l, with cycle counter

turning diameter: 1120 mm turning length: 6000 mm swing diameter over bed slide: 760 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Brand: Colombo Type: VUP 2S Year of make: 1978 Distance between centers: 6.000 mm Centre height: 560 mm Swing over bed: 1.120 mm ø Swing over support: 760 mm ø 4-Jaw chuck: 1.000 mm ø Digital read-out: Sony Including: 1 x steady rest 520 mm ø 1 x steady rest 950 mm ø 1 x open steady rest Chisel holder Chisel support automatic feed Rapid traverse chisel support Electrically movable counter center Drilling bar: length 2046 mm x 170 mm ø The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

DYNAJET 350th HELI The mobile and universally applicable dynaJET cold and hot water high-pressure cleaner 350th with up to 350 bar working pressure stands out in addition to its ease of use in particular due to its low weight, its compact dimensions and its high performance and safety level. Construction - 1-axle chassis for easy manoeuvring - Self-supporting and indestructible framework for weight optimization - Crane eyelet for easy transport and handling - Operating hours counter for optimal post-calculation - Underrun protection for additional safety - Frame in dip painting technology for high corrosion protection and highest surface quality - Targa concept with separation between the unit side and the operating side for enormous advantages in ergonomics, the Overall machine safety and noise reduction - Impact-resistant lockable hoods made of glass fiber reinforc ...

x-travel: 350 mm y-travel: 200 mm z-travel: 350 mm table surface area: 700 x 280 mm spindle taper: SK 40 : 150 - 1660 U/min feeds: 25 - 285 mm/min rapid traverse: 1 m/min quill stroke: 80 mm milling-head swivable +/-: 45 ° total power requirement: 3 kW weight of the machine ca.: 1,2 t dimensions of machine L x W x H: 1,27 x 1,1 x 1,65 m Accessories: vertical head with quill retraction, solid table, univ. Table, vice, rotary table 250 mmø, dividing unit with 3-jaw chuck 135 mmø, counter bearing, various tool fixtures, drill chuck, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

I sell here several machines, equipment forklifts, work platforms, spare parts for forklift work platforms and for woodworking, so be sure to pay attention to my other auctions Forklift Electric Forklift Three-wheel forklift LINDEN Type: E18 Year of construction: approx. 1994 Battery from 2019 According to the counter approx. 11600h Load capacity: 1800 kg at 500mm centre of gravity Lifting height approx. : 410 cm Construction height approx.: 255 cm Construction width approx.: 115 cm Fork length approx.: 115 cm Incl. side shift Incl. charger ( See pictures ACTUAL - condition) Prior viewing is expressly desired, just leave phone no. by mail, then I will get back to you for a viewing appointment. Subject to prior sale, all information is subject to change. The machines can be picked up by the buyer or shipped by a forwarding agent at the ...

Working width: 630 mm; Planing height: 300 mm; Planing shaft: Tersa; Number of knives: 4; Height adjustment: electric; Display planing thickness: mech. Counter; Feed speed: 5 / 8 / 12 / 18; Feed roller: steel; Pressure beams: articulated; Pull-out roller: rubber; Table rollers: no; Motor power: 9 kW; Suction port: 150mm; Machine length: 1200mm; Machine width: 1200 mm; Weight: 810 kg; Motorized thicknessing table stroke with two speeds Numerical display for working height Thickness table made of cast iron The thicknessing table is mounted on four large trapezoidal threaded spindles for maximum stability and precision Four feed speeds Optionally with two rollers in the thickness table Standard with noise protection and chip protection curtain on the workpiece inlet and outlet roller contact pressure adjustable Front feed roller with helical gear Pull-out roller with rubber ...

Diesel forklift Machine Brand: DOOSAN Designation: D90S-5 Year of production: 2012 Counter Reading (mtg): 7970 Empty weight (Kg): 12197 Lifting capacity (kg): 9000 Height. lift. (mm): 3100 Lateral fork travel Mast type: STD UDT review until March 2022 Fuel type: diesel After a large technical inspection for over PLN 30,000 (we have invoices for everything) - new tires - new fore fore fore - regeneration of actuators, - gearbox: discs + sealants - brakes: discs and bearings - all oils, liquids and filters Technical condition: used, very good

package from one place in austria: 1-color Offset printing machine Manufacturer: HEIDELBERG Model: GTO 52 Year: 1983 Format 35 x 52 cm Counter: 37000000 Location: Austria Pile Turner Manufacturer: Polar Model: PW1 Year: 2000 format 540 x 740 mm Load capacity 500 kg Location: Austria package Price: on request

Rotary feeder 1st unit : 4 buckles 2nd unit : 4 buckles 3rd unit : 4 buckles Batch counter MBO ASP 66-2ME press delivery Pumps

Details: Reference ID: PP-32945 Manufacturer: Komori Model: Litrone GLS 640 HUV LED Year: 2017 Color:6 Impression: 20 Mio Speed: 16000 sheets/h Max. Size: 720x1040 mm Condition: Good Location: Europe Availability: Immediately description: - Stock Thickness: 0.04-08mm - Colours: 6 and without coater - Dryers: HUV LED: 2 (one at the output and 1 after group 1 or 5 movable) - Condition: perfect as new condition - Cylinders: guaranteed damage free - Print counter: 20 millions - Equipped with Komorimatic-2 dampening system with delta effect, - PQC-S II, - automatic washers, - KHS AI, - Komori hyperspeed inking, - Self-learning, - Komori wall screen on console, - Refrigeration Baldwin, - KMS Komori management system, - Automatic blanket roller and impression cylinder washing devices, - ITC temperature control - Re-circulation

Triple flour-collecting screw conveyor in steel design Total length 6.2 m, outlet at 5.2 m Screw diameter 150 mm 1 m counter-rotating thread, slope 105 cleaning flaps, Wooden lid with folding boxes, 2 intermediate bearings each, motor 1.5 kw

Turning diameter: 0 mm Turning length: 0 mm Turret positions: 0 Positions ATC: 0   Number controlled axis: 0   CNC Brand: 0 CNC Model: 0 Control: FANUC Series O-T Technical data Number of axis total: 5 Max. turning diameter: 16 mm Turning length: 130 mm Max. drilling diameter: 8 mm Max. threading diameter: 6 M (Metric) Internal spindle diameter: 16 mm Spindle speeds: stepless from: 300 rpm up to: 8000 rpm Tool-holder: number: 5 Counter-operation: number of tools: 3 Drilling tools: 3 pce Spindle motor: 2.2 kW Machine´s weight about: 1300 kg Overall dimensions machine: Length: 1700 mm Width: 1000 mm Height: 1900 mm Various accessories: Set of toolholders

Turning diameter: 0 mm Turning length: 0 mm Turret positions: 0 Positions ATC: 0   Number controlled axis: 0   CNC Brand: 0 CNC Model: 0 Control: FANUC Series O-T Technical data Number of axis total: 5 Max. turning diameter: 16 mm Turning length: 130 mm Max. drilling diameter: 8 mm Max. threading diameter: 6 M (Metric) Internal spindle diameter: 16 mm Spindle speeds: stepless from: 300 rpm up to: 8000 rpm Tool-holder: number: 5 Counter-operation: number of tools: 3 Drilling tools: 3 pce Spindle motor: 2.2 kW Machine´s weight about: 1300 kg Overall dimensions machine: Length: 1700 mm Width: 1000 mm Height: 1900 mm Various accessories: Set of toolholders

Turning diameter: 0 mm Turning length: 0 mm Turret positions: 0 Positions ATC: 0   Number controlled axis: 0   CNC Brand: 0 CNC Model: 0 Control: FANUC Series O-T Technical data Number of axis total: 5 Max. turning diameter: 16 mm Turning length: 130 mm Max. drilling diameter: 8 mm Max. threading diameter: 6 M (Metric) Internal spindle diameter: 16 mm Spindle speeds: stepless from: 300 rpm up to: 8000 rpm Tool-holder: number: 5 Counter-operation: number of tools: 3 Drilling tools: 3 pce Voltage 50 Hz 3x: 380 Volt Spindle motor: 2.2 kW Machine´s weight about: 1300 kg Overall dimensions machine: Length: 1700 mm Width: 1000 mm Height: 1900 mm Various accessories: Set of toolholders

DYNAJET 350th HELI high pressure hot water cleaner. Including 1st UVV WITH arrival and maintenance (plus spare parts) on the same date (value approx. 1,500 net). The mobile and universally applicable dynaJET cold and hot water high-pressure cleaner 350th with up to 350 bar working pressure stands out in addition to its ease of use in particular due to its low weight, its compact dimensions and its high performance and safety level. Construction - 1-axle chassis for easy manoeuvring - Self-supporting and indestructible framework for weight optimization - Crane eyelet for easy transport and handling - Operating hours counter for optimal post-calculation - Underrun protection for additional safety - Frame in dip painting technology for high corrosion protection and highest surface quality - Targa concept with separation between the unit side and the operating side for eno ...

Turning diameter: 0 mm Turning length: 0 mm Turret positions: 0 Positions ATC: 0   Number controlled axis: 0   CNC Brand: 0 CNC Model: 0 Control: MITSUBISHI Meldas 70V Operating hours: 21070 Technical data Number of axis total: 5 + 2 Number of spindles: 2 Max. turning diameter: 16 mm Maximum turning length: 200 mm Max. drilling diameter: 10 mm Max. threading diameter: 8 M (Metric) Internal spindle diameter: 20 mm Spindle speeds: stepless from: 200 rpm up to: 15000 rpm Back spindle: speeds: from: 200 rpm up to: 10000 rpm Thread drill diameter: 5 M (Metric) Tool-holder: Turning tools: 6 pce Drilling tools: 4 pce Transverse processing tools: 4 Spindle speeds (turning tools): 6000 rpm Counter-operation: Drilling tools: 4 pce Voltage 50 Hz 3x: 400 Volt Total power required: 7 kVA Machine´s weight about: 2250 kg Overall dimensions machine: Length: 2020 mm Width: 1070 mm Height: 1680 m ...

Turning diameter: 0 mm Turning length: 0 mm Turret positions: 0 Positions ATC: 0   Number controlled axis: 0   CNC Brand: 0 CNC Model: 0 Control: MITSUBISHI Meldas 70V Operating hours: 23009 Technical data Number of axis total: 5 + 2 Number of spindles: 2 Max. turning diameter: 16 mm Maximum turning length: 200 mm Max. drilling diameter: 10 mm Max. threading diameter: 8 M (Metric) Internal spindle diameter: 20 mm Spindle speeds: stepless from: 200 rpm up to: 15000 rpm Back spindle: speeds: from: 200 rpm up to: 10000 rpm Thread drill diameter: 5 M (Metric) Tool-holder: Turning tools: 6 pce Drilling tools: 4 pce Transverse processing tools: 4 Spindle speeds (turning tools): 6000 rpm Counter-operation: Drilling tools: 4 pce Voltage 50 Hz 3x: 400 Volt Total power required: 7 kVA Machine´s weight about: 2250 kg Overall dimensions machine: Length: 2020 mm Width: 1070 mm Height: 1680 m ...

Format range: max. 1850 mm min. 420 mm Equipment: Longitudinal seam, folding bottom, double edge, 4-point gluing, electronic HHS top gluing unit with 4 application heads, disc bottom gluing unit on the left, Primary crusher left, motorized format adjustment, Kicker, counter, friction feeder with clocking, vacuum at the feeder, digital position indicator, motorized transfer station, middle station in folding, cutting alignment according to the feeder, Cutting alignment on the press belt. Overhaul 2023 with new feeder and transport belts, new Press belts top / bottom, cleaned, checked, painted Other: The machine can be viewed while running by appointment.

Turning diameter: 0 mm Turning length: 0 mm Turret positions: 0 Positions ATC: 0   Number controlled axis: 0   CNC Brand: 0 CNC Model: 0 Control: MITSUBISHI Meldas 70V Operating hours: 23805 Technical data Number of axis total: 5 + 2 Number of spindles: 2 Max. turning diameter: 16 mm Maximum turning length: 200 mm Max. drilling diameter: 10 mm Max. threading diameter: 8 M (Metric) Internal spindle diameter: 20 mm Spindle speeds: stepless from: 200 rpm up to: 15000 rpm Back spindle: speeds: from: 200 rpm up to: 10000 rpm Thread drill diameter: 5 M (Metric) Tool-holder: Turning tools: 6 pce Drilling tools: 4 pce Transverse processing tools: 4 Spindle speeds (turning tools): 6000 rpm Counter-operation: Drilling tools: 4 pce Voltage 50 Hz 3x: 400 Volt Total power required: 7 kVA Machine´s weight about: 2250 kg Overall dimensions machine: Length: 2020 mm Width: 1070 mm Height: 1680 m ...

Key data: 90 , 10 , 13

High quality oil screw compressor used in industrial plants, factories, production halls and larger workshops. This compressor uses direct drive, which is the most efficient way of drive. The helical stage is directly coupled to the electric motor by means of a flexible coupling. Thanks to this solution, there is no energy loss when transferring torque from the engine to the block, and energy consumption is significantly reduced. Manufacturer: AIRPOL Model: NB 90 Flow rate: 820 m3/h Pressure max. 1.0 MPa Motor power: 90 kW / 160 A Load counter: 24.138 h Weight: 2300 kg Year of Build: 2012 Full DTR documentation and UDT audit book with tank passport Technical condition: used machine

Folding machine H+H KL 112-45-T10; built in 2002; good condition; cleaned and tested; Inlet width 450mm; 10 folding pockets; Investor Gremser FN-K-TH; Area dial counter HHC-100; Transfer No.220.1-45 built in 2016; 2.Falzwerk KL112.1-mobil-45 Bj.2016; 6 folding pockets; Standing sheet display No.177-mobil 45 built in 2013; Display No.701-1500-52 built in 2016. Folding machine H+H KL 112-45-T10; good condition; cleaned and checked; working width 450mm; ten pockets; feeder Gremser FN-K-TH; count unit HHC-100; hang up conveyor No.220.1-45 year 2016; secound unit KL112.1-mobil 45 year 2016; six pockets; smal format delivery No.177-mobil45 year 2013; stream delivery No.701-1500-52 year 2016.

Column drilling machine ALZMETALL type AB 4 SV Masch. No. 14805 Year of construction approx. 1980 Drilling capacity 40 mm Spindle mount MK 4 - short quill Projection 340 mm Quill stroke 180 mm Table size 710 x 560 mm Column diameter 160 mm Spindle speed 30 - 765 rpm infinitely variable Motor power 2.3 and 3.4 kW pole switchable Mains connection 380 volts, 50 Hz spindle speed via 2 gear stages and infinitely variable via variator gear - Counter stage for high torque at low speeds - Spindle on/off via rotary switch or electric foot switch - Automatic feed 0.1 - 0.2 - 0.3 mm/U - Table height adjustment via hand crank - Machine foot with machined workpiece contact surface - LED lighting device Space requirement L x W x H 1200 x 725 x 2050 mm Weight 615 kg good condition; used

Shredding plant / chipper / shredder for shredding wood waste - Waste wood waste - Pallets - Packaging material and waste of many kinds Make: VECOPLAN - MASCHINENBAU Type: VAZ 300/180 Silent and slow-running. Propulsion:132. Kw. Rotor width:1800.mm. Rotor diameter:420.mm.(solid steel.) Rotor speed:80-120 rpm Capacity: 1500-2000.kg/h.je by material and task. Tools-knives ( cutting crowns 80x80 mm ) Sieve: 30.mm. round hole reinforced design Hydraulic strainer and rear flap with lowerable counter knife Conveyor belt cut-out 1000.mm. Insertion: approx. 1800 x 3000.mm. Weight: approx. 18.500.Kg. Included: control cabinet system + hydraulic system + operating instructions + electrical circuit diagrams. Dealer price 34.500.00€ net ex location. The machine is in good general condition

Folding carton boarding machine Uhlmann C 100 LB • Format range folding carton B 30-100, H 15-75, L 70-200 mm • Capacity 10-80 folding cartons/min, clocked • For offset plug-in closure on both sides • Product feed for blister via blister stack shaft • Code reading Laetus Argus for 2x brochure code (front + back), 1x folding carton code, 1x brochure absence in folding carton • Brochure folding and inserting machine from the magazine GUK FA 21/4 Cartonac 91 • Colour embossing station for folding flap opposite the insertion side, 2-line, with embossing numbers • Poor ejection with ejection counter-control • Vacuum generators • SPS Eberle PLS 514 • Connection 400V/50Hz Optional: - New hardware/software Mitsubishi with 8" color Tuach Panel - Code reader Cognex - Validation documentation

Fat baking station mobile sales counter on rolls with grease baking device Drawers + cash register separate sink in the drawer with power connection Height: 175cm Width: 190cm Depth: 80cm