console used for sale

Tank- & Environmental Protection Wozniack Specialist company according to Section 19 water budget law Ladies and gentlemen, we offer a 50,000 litre single-wall insulated storage tank as follows. Rated capacity 50 cbm Piece 1 used but overhauled, i.e. the container is cleaned, externally insulated. Material steel, material S235JRG2 Documents Manufacturer's certificate / test certificate according to DIN and type plate Piece. Piece. 1 vent nozzle Piece. 1 filling nozzle Piece. Piece. Piece. 1 ladder Piece. Form. cylindrical storage container with feet/console Container dimensions Length approx. 10,740 mm plus insulation 100 ...

Pierce Control Automation RUR 2500 P working range: 2.1 m x 6.1 m control: Burny 10 LCD Completely welded portal construction without screwed connections o linear guide in the transverse axis o AC servomotors (12 000 mm/min.) o Digital synchronization on the laeng axis o CNC control system BURNY 10 LCD Plus with touch screen o membrane keyboard o flyingmounted cutting buttons o Automatic initial adjustment of the plasma torch o voltage monitoring of the plasma torch height o 1 torch parking lot outside the cutting area o circuit breaker at the end of all axes 1 x Plasma Kjellberg 160i with manual gas console cutting up to 25mm qualifying cut Optional autogencan Completely factory-assembled machine assembly and commissioning ready for use

Fully automatic unwinding reel Remote control console Automatic and manual working mode Fine adjustment of speed Potentiometer Simply synchronized with punching machine Reel motorized, with Central Expansion Reel run both directions, prewaerts and rueckwaerts with loop sensors control Speed from 0.1 to 30 RPM rpm Engine with gearbox Reel max load 1 ton Winder strip width up to 300 mm Inner diameter 250 mm min max. 500 mm Outer diameter max. 1300 mm Power 0.37 KW Dimensions 1,200 mm x 1,200 mm height 1,600 mm with CE certificate in stock 2 essa, 2 shaal and 12 brother general overholt punching machines

Fresh concrete recycling plant BIBKO RAM 20/ used manufactory: Bibko type: RAM 20 YOM: 2001 Capacity: ca. 12 m³/h system washing trough, trough length 2500 mm separating layer 0,25 mm with discharge conveyor screw (new) overhauled/reconditioned and exactly aligned - gear reconditioned (overhauled) and sealed - all bearings are new - buckets and scraper exactly aligned - 1 pcs feed hopper / used - 1 pcs agitator (wastewater) with console / used - 1 pcs control unit / used -for the full automatic control of the complete plant - 1 pcs gallows-shaped pipe/ used Facility is fully equipped, clean and primed. The final painting according to customer's request. location: South Germany available: march 2024 offer and all price are net and ex stock without guarantee and/or guarantee, mistakes and/or false representations reserve, purchasing like ...

New 161 i with automatic gas console year construction year 2015 installation and commissioning on request data see PDF HiFocus 160i 400V ArH2N2/O2 up to 15m with plasma torch connection unit Oxygen; Nitrogen; Argon; Hydrogen; Air oxygen; Nitrogen; Forming gas 5; Air plasma machine burner PerCut 170-2 with vortex gas ; immediately available

Plasma cutting system for attachment/post-training CNC cutting and plasma cutting FineFocus 800 Plus Materialstaerke: up to 80 mm, hole stitching and quality cutting up to 45 - 50 mm, Gas console type PGE 3-800 (Kjellberg) - Description of the plasma cutting source (see appendix) Year of construction: Dec. 2005 (commissioning 2006) Condition as new (new price of the plant 46,327.70 EUR) Special price: 19,900 EUR + VAT ex works Bochum-Wattenscheid plasma cutting plants FineFocus 800or alternatively as FineFocus 1600 cutting up to 160 mm (see systems) plasma cutting systems FineFocus 800 and FineFocus 800/TWIN now with PLUS technology preferably for automated and mechanized cutting in connection with guide machines and robots on all electrically conductive materials; with or without vortex gas, also under water. cutting range up to a maximum of 80 mm material thickness (materi ...

Pierce control automation RUR 2500 P Work area: 2.1 m x 6.1 m Control: Burny 10 LCD Fully welded Portal construction without bolted connections o LM Guide in the transverse axis o AC servo-motors (12 000 mm / min.) o Digital synchronization on the longitudinal axis o CNC control system BURNY 10 LCD Plus with touch screen o Membrane keyboard o 'Flying' bearing inserts o Automatic initial setting of the plasma torch o Voltage monitoring of plasma torch height o 1 burner parking outside the cutting area o Circuit breaker at the end of all axes 1 x plasma Kjellberg 160i with manual gas console Cut quality cutting up to 25 mm Optional autogen retrofittable Completely Factory reconditioned machine Installation and commissioning on request

Plasma cutting machine ESAB working area 1500 x 3000 1 x autogen up to 200 mm 1 x Plasma Hifocus 160 i with automatic gas console. see PDF document several plasma change torches available Very well maintained from: 10 / 2012; ready for use

Kjellberg Hifocus 160i used with manual gas console . only 504 operating hours. data see pdf; ready to use

A used S O R A L U C E CNC driving stand milling and drilling center FS 16000 Built in 2000 MAIN TECHNICAL DATA: Travel: Longitudinal (X): mm 16000 Senkr. (Z): mm 1600 Cross (Y): mm 1500 Milling and drilling spindle: Tool holder: ISO 50, DIN 69871 Auto. Tool tension: clamping force 15000 N Tightening bolt: DIN 69872 Form B (BT50) Spindle speeds: Special speeds: rpm 20-3000 Feeds: Feed range: mm/min 2-5000 Rapids: X-axis: mm/min 12000 Y- and Z-axis mm/min 15000 The machine is equipped with: - HEIDENHAIN control TNC 426 M. - Operator's platform in the X-direction with sliding door and Viewing windows against chip flight and splashing water. - Operator's console swivels mounted on the stage. - Automatic thermal expansion compensation of the Milling sliders. - Automatically indexing milling head. This milling head enables the fully automatic m ...

Working range: 2500mm x 6000mm rail length: 8000 mm track width: 3000 mm racks and drive pinion renewed at the end of 2011. Last recovery at the end of 2011. Control Sato CNC 3000 2 x Autogen 1 x Plasma Kjellberg 160 i with automatic gas console (see Pdf) 1 x Support for koerning Complete with table and suction assembly and commissioning on request ; ready for immediate use

Built-in screwdriver with control, BL57/50 MDW, 457010, Pico/mA, DSM, used Top Attention special price! (For your info - current new price for this screwdriver and control € 9.500 excl. VAT) We have set the lowest price on the market for a comparable used part. We still have several identical and other such units, but the quantity is ending. If you buy more than 1 piece you will get a great discount. If you have a UID number we will gladly issue an invoice without VAT. Used - Top condition The part was bought from a company in the course of a machine dismantling and is in very good condition. Technical data: Screwdriver BL57/50 MDW, DSM 457010, max. 50Nm, incl. all cable sets. This high quality DSM screwdriver is designed for direct measurement of torque and angle of rotation. The high-precision transducers required for this are installed directly on the output. The meas ...

The Prima Power Platino 1530HS laser was produced in 2006 by the Italian company Prima Industrie S.p.A. The 4 kW laser is equipped with a Primach 20L CNC control. The machine is used for cutting metal sheets with a thickness of 20 mm (black steel), 12 mm (stainless steel) and 8 mm (aluminum). The laser has an independent F axis with programmable focus position and nozzle distance. The maximum feeds in the X / Y / Z / F axes are respectively: 3050 mm, 1525 mm, 150 mm and 25 mm. The machine is equipped with: a Prima Power Convergent Lasers Division CX 3000 resonator with a power range from 200 to 3000 W and a cooling unit. In addition, the price of the laser also includes 3 cylinder regulators made of chrome-plated brass with a stainless steel diaphragm in the first stage of reduction and a bellows structure in the second stage of reduction, and 2 cylinder regulators for oxygen and nitroge ...

Microstep CNC plasma and cutting system working area: 6000mm x 1500mm+800mm 1 x Plasma support ( Hifocus 160i Kjellberg with automatic gas console) (cut and mark see PDF) 1 x Autogensupport incl.

Console robots (several in stock, paint in Orange) Robot KUKA KR180L100K Built in 2003 Reach 3500mm Weight 1425kg Load 100kg Control KRC2 Weight 185kg Software version V4. 1 7 SP08 KUKA KCP2 Connection cables 7 m / 15 m .

The JAFO FYN 50 ND CNC milling machine was produced by Jarocińska Fabryka Obrabiarek S.A. in 2007. The machine is equipped with the working table of dimensions (W x L) 500 x 1400 mm and CNC control HEIDENHAIN. The numerical control allows to work in an automatic cycle with a circular or linear interpolation in three-dimensional space. Machine feeds in the X/Y/Z axes are 800 mm, 500 mm and 500 mm respectively. The CNC milling machine weighs 4500 kg. A fourth axis can be connected to the machine control panel. Technical specification of the JAFO FYN 50 ND machine - CNC control: HEIDENHAIN - working table surface (W x L): 500 x 1400 mm - feed rates in the X/Y/Z axis: 800/500/500 mm - stepless feed rate adjustment - spindle nose: ISO 50 - stepless regulation of spindle rotation speed - metering lubrication system - guide rails lined with TURCITE B” material - hydromechanical q ...

Sato LS 2500 CNC 3010 working range: 2000mm x 4000mm 1 x Plasma 280i Kjellberg with automatic gas console Recommended cutting range from 0.5 to 50 mm Materialstaerke (HiFocus 280i) with suction system very good condition, on request ready for immediate use

Fine beam plasma cutting system HD 3070 with manual gas console incl. Arcwriter hose package suitable for 3m x 8m systems; ready for immediate use

tahlkonsole with height adjustable table Table 720 x 500 mm, thickness 8 mm Weight 20 kg Built in 1975 The console is in good condition, ready to use. Subject to changes, errors, prior sale! Service/Ersatzteile durch MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system+technik GmbH Maschinenbau Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland

Plasma cutting system / power source Manufacturer: Kjellberg Type: PA-S47 CNC Year of construction: 1994 Cutting power: 40-130 A Quality section: 35 mm Cut: 45 mm Gas console: PV-S75W-1 without hose package .

Product name: Compressor Manufacturer: Kaeser Type: EPC 340-100 Article number: 1.5746.7 Year of construction: 2011 Condition: in good used condition, checked technical details: operating pressure: 10 bar • Delivery quantity: 230 l/min (6 bar) • Speed: 1,500 rpm • Container: 90 l • Weight: 73 kg without consoles (per console 15.0 kg) • Sound pressure level dB(A): 73 Engine data: • Motor: 400 V, 1.7 kW Metrics: L x W x H: 1,120 x 350 x 910 mm Transport dimensions: • L x W x H: approx. 1,200 x 800 x 1100 mm • Transport on pallet: 1,200 x 800 mm Our price: 839,00 € (EUR) FP plus VAT from location Grunow (Brandenburg) (Subject to changes and errors regarding technical data and prices!) In accordance with our terms and conditions, we would like to point out once again that cheques and bills of exchange cannot be accepted.

Hifocus 160 i with automatic gas console PGV 2 with Percut 450 quick-release head with torch hose package 6m assembly and reversing on request.; ready for use

CNC console milling machine make MEXPOL JAFO type FXH 400 NBMachine -No: 0505 built in 1984Table clamping surface: 400 x 1250 mmTravel X-axis: 900 mmTravel Y-axis: 250 mmTraverse Z-axis: 450 mmTool holder: ISO 5016 spindle speeds: 56-1800 rpm.continuously variable feed rates X and Y axis: 2-2000 mm / minstepless adjustable feed Z-axis: 1-1000 mm / minRapid traverse X- and Y-axis: 3200 mm / minRapid traverse Z-axis: 1600 mm / minDrive power: 11 kWDimensions: 2800 x 2990 x 2150 mmWeight approx. 3600 kgWith- Railway control HEIDENHAIN TNC 151- Horizontal holderused, from one operational resolutionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Complete engine Deutz BF6M Diesel Type BF6M1013EC 153KW /1500rpm Complete motor with water cooler and intercooler, turbocharger, air filter, starter, flywheel, regulator etc. New condition with approx. 400 operating hours from an emergency generator Motor is built on a console and can be introduced. BF6M 1013 EC BF6M 1013EC BF6 M1013EC BF6 M 1013EC BF6 M 1013 EC BF 6M1013EC BF 6M 1013EC BF 6M1013 EC BF6M1013 EC Special price

Vertical console milling machine make HECKERT type FSS 315 SMachine -No: 314212/2 Year 1992Table longitudinal path X-axis: 950 mmKonseol vertical path Y-axis: 450 mmTransverse Z-axis: 500 mmCross slide cross travel: 270 mmTable size W x L: 430 x 1600 mmNumber of clamping stages: 4Table load: 1000 kgSpindle mount: ISA 4018 speeds: 28 - 1400 rpm.18 feeds lengthwise: 16 - 800 mm / minxa0xa0xa0 vertical: 5 - 250 mm / minRapid traverse longitudinal and transverse: 3150 mm / minRapid traverse vertical: 1000 mm / minDrive power: 1.5 kWConnected load: 8.0 kWDimensions: 2800 x 2800 x 1995 mmWeight approx: 3000 kgWith- swivel spindle head- tableau control- Control cabinet SIEMENS- Central lubricationused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be plea ...

CNC Portal Plasma Cutting Machine Manufacturer: ESAB Eagle 2500 Year of construction: 2004 Control: Vision DNC Connection track width: 2,500 mm runway: 5 m Working area: 2 x 3 m Extraction table 1 plasma torch with power source Kjellberg HiFocus 160i automatic gas console (see PDF) cutting tools: up to 25 mm filter cutting system: Columbus Immediately available ; ready for immediate use

Universal console milling machine make WMW HECKERT type FU 355 x 1250Masch. -No: 47512/1962 built in 1962Table mounting surface: 355 x 1250 mmTable can be swiveled 45 ° on both sidesTable can be swiveled: + - 45 °Table longitudinal path X: 1120 mmCross slide cross travel: 345 mmConsole vertical path: 400 mmTable load max .: 1500 kgSpeed range: 28 - 1400 rpm.Feed area longitudinal and transversal: 16 - 800 mm / minFeed range vertical: 5 - 250 mm / minRapid traverse longitudinal and transverse: 3150 mm / minRapid traverse vertical: 1000 mm / minTool holder: ISO 50Drive power: 14.5 kWWeight: 3850 kgExternal dimensions: 2400 x 2300 x 1800 mmused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available  ...

Manufacturer: MicroStep Type: SPL-PA 3001.15+S500 Working range: 3000 x 1500 mm + 500 mm shaft technology: plasma built in 2006 Kjellberg HiFocus 160i with autom. Gas console; (see PDF) 2 x additional quick-release co-buttons PerCut 170 Div. Wear parts Donaldson filter system including disassembly and delivery within Germany. Commissioning on request.

Bosch Turbo Scara SR6 swivel arm robot + controller Rexroth MA4/200-7301-M + RH04.0S Manufacturer: Bosch Tripod Length: Console HubQuill 40025 PN pressure max. 8 bar Load max 8 kg weight 48,5 kg incl. control Control consisting of the following components: Rexroth / MA4/200-7301-M / Robot Controller Module Rexroth RH04.0S Swivel range / technical data see picture Since the article is available several times and the robots carry different work tools these are only sample images and may differ. Item condition used (Changes and errors in the technical data, information is reserved!) In addition to about 50 paternosters, countless other machines such as presses, robots, furnaces, industrial vacuum cleaners, etc. are available. Workshop equipment, workbenches, workshop trolleys, tools, forklifts and shelves abundantly available A total of 24,0 ...

Plasma cutting system with Hypertherm HPR 130 with automatic gas console Cutting up to 20mm Working range: 1500mm x 3000mm inlusive filter system Immediately available under current assembly and commissioning on request

Plasma cutting system with Hypertherm HPR 130 with automatic gas console cutting up to 20 mm Work area: 1500 x 3000 mm included filter system available under current mounting and commissioning on request

4 ROLL HYDRAULIC MODEL M2008 EVO_4.0 CNC GRAPHIC CAD-CAM Machine serial number 2022 PLATE BENDING ROLL PLANETARY DESIGN DOUBLE PINCH PRE-BENDING Capacity -Width of plate: 2000 mm -Thickness of plate rolling 8 mm -Thickness of plate pre-bending 6 mm -top roll 190 mm -lower roll 170 mm minimum rolling shell ID 220 mm -Power 5,5 Hp to run the hydraulic unit Voltage 400/50 – 480/60 -Weight of the machine 3400 Kg Configuration installed Surface hardening of the four rolls, smooth finishing suitable for stainless plates rolling Dual pre-pinch, with adjustable force upon the input of plate thickness Conical bending hydraulic attachment - hardened contrast pad. Power driven rolls rotation top/bottom gearbox axial direct drive hydraulic each roll. Calibration system f re-rolling of welded shells rounding. Console electric in ...

Fine beam plasma cutting system HD 3070 with manual gas console incl. Arcwriter Hose package plant suitable for 3 m x 8 m

Max speed 150 m/min Unwinder + E&L web guide Ø 1000 m, max. weight 300 kg Printing units 8, gearing 1/8”CP Max. web width 413 mm Max. print width 407 mm (16”) Printing cylinders 16 x 12,625” (320,662 mm), 16 x 14,125” (358,77m mm) Anilox cylinder see list Lateral register: ± 5 mm Longitudinal adjustment unlimited at all printing and die cutting stations, selectable from mobile control console, smallest adjustment 0,05 mm. Automatic register control: Sensotec automatic register control, web to web comparison for print stations and web to cylinder for die cutting stations. Front to Back Register control system Web inspection Tecscan web inspection system Drying optimized hot air drying Web turner rail mounted moveable platform with E&L web guide. Webguide Fife web guide before rot ...

CNC Portal plasma cutting machine Manufacturer: ESAB Eagle 2500 Year of construction: 2004 Governance: Vision DNC connection Track width: 2,500 mm Career length: 5 m Work area: 2 x 3 m Vacuum table 1 plasma torch Kjellberg HiFocus 160i power source automatic gas Console (see PDF) Cutting thickness: up to 25 mm quality section Filter system Cutting software: Columbus Now available

FANUC M6IB 6S (year 2006) Available: (1) M16IB + FANUC SYSTEM R J3IB Controller + console (1) M16IB + FANUC SYSTEM R J3IB Controller The FANUC M-6iB/6S is a short arm for tight, confined spaces. The robotic arm of the M6iB/6S RJ3iC is used to treat products where parts sizes and envelopes are of little concern. The M 6iB/6S can perform acute, lightweight material handling with a repeatability of +/- 0.08 mm and a maximum payload capacity of 6 kilograms. Robot Specifications Axes: 6 Reach: 900mm Repeatability: ±0.08mm Robot Motion Speed J1 - 200 °/s (3,49 rad/s) J2 - 200 °/s (3,49 rad/s) J3 - 260 °/s (4,54 rad/s) J4 - 400 °/s (6,98 rad/s) J5 - 400 °/s (6,98 rad/s) J6 - 720 °/s (12,57 rad/s) Robot Motion Range J1 ±170° J2 ±125° J3 ±155° J4 ±190° J5 ±140° J6 ±360°

Details: Reference ID: PP-32945 Manufacturer: Komori Model: Litrone GLS 640 HUV LED Year: 2017 Color:6 Impression: 20 Mio Speed: 16000 sheets/h Max. Size: 720x1040 mm Condition: Good Location: Europe Availability: Immediately description: - Stock Thickness: 0.04-08mm - Colours: 6 and without coater - Dryers: HUV LED: 2 (one at the output and 1 after group 1 or 5 movable) - Condition: perfect as new condition - Cylinders: guaranteed damage free - Print counter: 20 millions - Equipped with Komorimatic-2 dampening system with delta effect, - PQC-S II, - automatic washers, - KHS AI, - Komori hyperspeed inking, - Self-learning, - Komori wall screen on console, - Refrigeration Baldwin, - KMS Komori management system, - Automatic blanket roller and impression cylinder washing devices, - ITC temperature control - Re-circulation

Facilities: -Console machine with cantilever -Pneum.. Workpiece stops with double-acting cylinders -Pneum.. Assembly AIDS -additional editing fields front (4-field machining) -Handheld -C axis -Swivel sawing unit to the grooves in the X - and Y-direction -Horizontal milling unit for lock box -Plate tool changer driving with - laser positioning aid for the cleaner -autom. Central lubrication system Technical data: -Traverse path Max X: 3.259 mm -Traverse path Max Y: 1,483 mm -Maximum Z: travel 325 mm -Speed Max x: 75 m / min -Speed Max Y: 75 m / min -Maximum Z: speed 30 m / min -Workpiece thickness max: 100 mm -Spindle motor power: 7,5 kW -Main spindle speed: 1000-18000 RPM -Recording of main spindle: HSK 63F -Recording spindles: M10 with 11 mm fit -Number of vertical spindles: 14 pieces -Number of horizontal twin spindles in the X direction: 1 piece in the Y-d ...

Ideal CSR Typ. 201 - 21 wire mesh production line CSR Project Jig welding machine Year of manufacture 1996 Switch / control cabinet kVa125 Made in Germany Control: W/Siemens Handheld Computer Control Mounted In Enclosed Wire Cage Safety Structure The coordinate welding machine CSR 201 is used for resisting point welding of sheet metal and wire products in stencils: Work-piece dimensions: Length max.1800 mm Width max. 750 mm Nldw7 Height max. 200 mm X-axis for driving the welding unit according to the work piece length, with a base frame, hardened liner guides, serrated toothed rack system and servomotor with incremental encoder, travel max. 1800mm programmable, max. Travel speed 1500 mm / s Positioning accuracy +/- 0.2mm Y axis for driving the welding unit according to work piece width, with hardened linear guides, rack system and rotary servo motor with incremental ...

Working range X mm: 7200 Working area Y mm: 2010 Working area Z mm: 300 No. 2 working areas mm: 2700 x 1500 Main motor kW: 11 Tool change stations 12 Machine table: console table Speed max rpm: 18000 Tool clamping system: HSK 63F Number of consoles 8 Vacuum pump: Yes Total connection kW: 78 Weight Kg: 12,300

-) Working area X: approx. 3,300 mm -) Working area Y: approx. 1,300 mm -) Working area Z: approx. 300 mm -) Main engine: approx. 7.5 kW -) Tool change points: 2 x 24 pieces Fix and 1 x 10 with you -) Lock box unit: permanently installed -) Machine table: console table -) Positioning aid: Yes -) Workpiece special clamping system: Yes -) Software: SCM XILOG 3 -) Number of milling spindles: 1 piece -) Speed: 18,000 max rpm. -) Torque support: Yes -) Tool clamping system: HSK-F63 -) Design: boom machine -) Vacuum pump: Yes -) DXF interface: Yes -) Chip conveyor belt: Yes -) CE mark: J Yes -) Total connection: approx. 22 kW -) Weight: 9,600 kg

Used cutting system Schmidler S4 Built: 2005r Condition: in operation, very good Technical data The machine has the following equipment: 1. Fully automatic wood conveying with feed roller conveyor and feed and feeding cross conveyor 2. Under-table swivel cross-cut saw with 4-axis control saw blade d=720mm, 3. Universal milling unit 4 -axis, combi cutter 350 diameter,100/20-,40-,60 he combi, finger cutter 40/140, swallowtail cutter 45mm 4. 1x drilling rig (2.2 kW) - drilling direction horizontally 5. 1x slotted unit, sword 10/50/400mm (3.0 kW) - direction of operation horizontal 6. 1x drilling rig (2.2 kW)– drilling direction vertically from below 7. 1x Profiel cutter, d=120mm, L=250mm with dovetail cutter working direction vertically from below 8. Marking device vertical 9. Control board unit, cutter thickness 20mm, 10. Fully automatic beam turning station 11. Tran ...

- for processing hinge systems and connection fittings - Advantages of hole-row drilling in the system 32 - Machine stand with lift - Switching console - Foot pedal - Pneumatic connection (6 - 7 bar, air consumption per stroke 1.2 ltr.) - Blow-off gun incl. hose and T-connection - Drilling gearbox with 19 spindles - pneumatic holders - Press-in die present - Stop ruler - Table profiles - Wooden pad - Suction nozzles (diameter 80 mm) The machine is mounted on a mobile cabinet and can also be delivered with it. The machine is completely cleaned and has been checked for its function. (Changes and errors to technical data and prices reserved!)

Key data: 3100 mm, 6 mm

HACO TS 3006 hydraulic guillotine shears manufactured in Belgium in 2006, are used in manufacturing plants to cut steel sheets with a maximum length of 3100 mm and a thickness of 6 mm. The machine has vertically aligned knives with four cutting edges, which ensure high precision and quality machining of workpieces regardless of the thickness and type of sheet. The angle of the cutting knives and the gap between them are adjusted by means of two levers at the rear of the machine. During machining, the workpiece is pressed against the cam in order to take an accurate measurement on the gauge located between the front stop and the bottom knife. Two parallel hydraulic cylinders drive the cutting bar (the upper knife attached to the slider) to perform the movement in the up-down direction. The HACO guillotine shears are offered with equipment which includes a foot control, a modern HACO SP ...

4 ROLL BRAND NEW MACHINE 2000X20MM -plate width 2000 mm -plate thickness 20 mm -prebend 14 mm -Top roll mm. 280 -lower roll mm. 260 -Power electric 380/50 Minimum rolling ID 330 mm Capacity 2000 X 20 mm Capacity 1000 x 25 mm -4 rolls hardened very high strength on surface -direct driven rolls rotation with axial planetary gear + hydraulic motor each roll. -conical bending hydraulic tilt angle for plate rolling conical reducers -rerolling system for welded plates to pass automatic welded seams thru -overload protection hydraulic safe operation. -console centralized with electric joysticks -rollers position bending and pre-bend digital readout CNC EVO graphic controller automatic fully programmable 4 axis plate rolling. Auto-calculate programs upon plate data input and test. .dxf files from cad station immediate drawing import and run bending program.  ...

ECKERT AGAT SPEED gas cutting machine was manufactured in Poland in 2014. The machine designed for precision cutting of metal sheets with a maximum thickness of 100 mm is distinguished by a high-quality portal with an open structure, ensuring excellent stability during the performed cutting process and free access of the operator to the working space. The contamination generated during the cutting process is continuously removed by a sectional extraction table covering the entire working area of the machine. The ECKERT gas cutting machine is also equipped with, among others, a state-of-the-art CNC ECS 872 controller and an oxygen torch support with capacitive distance sensor. Technical data of the ECKERT AGAT SPEED CNC cutting machine - CNC control: ECS 872 - maximum workpiece thickness: 100 mm - work table surface (L x W): 3000 x 2000 mm - oxygen torch support with capacitive dis ...

TECHNICAL DATA: Field X: 4320 Field Y: 1550 Workspace Z: 280 02 Main engines Kw: 8 x 2 Tool change positions: 8 x 2 Worktop: Console table Software: Fanuc 180 Number of milling spindles: 2 Max g/min rotation speed: 18000 Horizontal drill tips X: 8 Horizontal drilling tips Y: 18 Number of bars: 8 Vacuum pump: 2 Pump capacity for empty m3/h: 150 x 2 Chip conveyor belt

Automatic labeling train from the manufacturer BIZERBA, GLE model, Automatic equipment with static weighing for weight labeling and fixed prices (WITHOUT SCALE) High quality equipment and great performance in terms of speed and reliability. Allows you to label products with weight information and fixed prices. Ideal for top labeling. OUTSTANDING FEATURES   Possibility to label fixed weight-amount. Order Management Tagging totals Generic traceability on label Adapted to comply with EU regulation 1169/2011 regarding food information. Barcodes: EAN-8, EAN-13, EAN-128, CODE 128, ITF-14, GS1 Datamatrix and GS1 Databar (up to 4 codes per label). WEIGHING TYPE Static, with tape width 300 x length 430 mm. LABELLING SYSTEM TYPE OF PRINTING Direct thermal.- PRINT HEAD. Long-lasting head and resolution 8 dots/mm APPLICATION OF LABELS Applica ...

WEINIG / GreCon Short Wood Finger-jointing Line Ultra TT Data of the system: • Wood inlet length (min. - max.) 150 - 1000 mm (1300 mm) • Reference timber inlet length at the finger-jointing line 400 mm • The length of the wood to be processed must be at least 25 percent longer than the width of the wood to be processed • Wood thickness (min. - max.) 20 - 80 mm • Reference wood thickness 28 mm • Wood width (min. - max.) 40 - 205 mm • Reference wood width 90 mm • Reference wood cross-section 28 mm x 90 mm • Wood outlet length (min. - max.) 3000 - 6100 mm • Reference wood outlet length 6100 mm • Tine profile (length) 10 – 11 mm • Max. wood cross-section for processing softwoods (with specified tine length) 100 cm² • Max. wood cross-section for processing hardwoods (with specified tine length) 80 cm² • Glue type PVAC • Species: Softwood / ...

Manipulator arm #5051 Electrical lift motor Pneumatic holder Manufacturer: KAHLMAN / Quick system Type: AGM 10 Ceil Overall size: 550x2200x1100 mm Console length: max.4000 mm Lift height: 1700 mm Load: 75 kg