conical used for sale

Plate cutter, composite stone cutter, stone pincers, plaster stone pincers -for effortlessly cutting slabs and composite stones to length through the translation of the eccentric lever -great stability with low weight -exact guidance of the cutting knife -pendulum suspended upper knife for cutting materials that have a conical cross-section (curbs) -Max. for 6 cam stones -Own weight: 10 kg

Hydraulic pump PARKER, PMD-CHEMNITZ 3349111716 shaft diameter: Ø 15 / 18 mm x 20 mm (conical) shaft thread: M12 x 1.5 Flange: 114 x 90 mm New ! Dimensions: 145 x 90 x 115 mm

Encoder, speed sensor HEIDENHAIN ERN 1381.001 - 2048 ( ERN1381.001-2048 ) 313 453 02 Shaft: Ø 9 / 10 x 10 mm ( conical ) Flange: Ø 58 mm with documents ! used, checked ! Dimensions: 68 x 58 x 58 mm

Servo motor CID Type: HSM 60 ( HSM60 ) Power: 60 W Voltage: 12 V DC Shaft diameter 1: Ø 7 / 8 mm, length: 16 mm, conical with thread: M5 x 0.8, length: 8 mm Flange diameter 1: Ø 60 / 102 mm, Bolt circle diameter: Ø 92 mm with 4x threaded hole: M4 x 0.7, depth: 10 mm shaft diameter 2: Ø 7 mm, length: 29 mm flange diameter 2: Ø 60 mm, bolt circle diameter: Ø 48 mm with 4x threaded hole: M4 x 0.7, depth: 10 mm used, tested ! Dimensions: 145 x 106 x 106 mm

Servo motor CID Type: HSM 150 ( HSM150 ) Power: 160 W Voltage: 24 V DC Shaft diameter 1: Ø 8,5 / 10 mm, length: 20 mm, conical with thread: M6 x 1.0, length: 8 mm flange diameter 1: Ø 118 / 142 mm, Bolt circle diameter: Ø 130 mm with 4x threaded hole: M5 x 0.8 shaft diameter 2: Ø 7 mm, length: 29 mm Flange diameter 2: Ø 70 mm, bolt circle diameter: Ø 48 mm with 4x threaded hole: M4 x 0.7, depth: 10 mm New ! Dimensions: 160 x 120 x 120 mm

Servo motor with pulse coder FANUC A06B-0614-B031 2000 rpm 108 V 12 A Shaft: Ø 13 / 16 x 30 mm (conical) Flange: 130 x 130 mm used, tested ! Dimensions: 380 x 140 x 150 mm

sheet width: 2050 mm plate thickness: 6,0 mm pre-bending capacity: 4,0 mm upper roll diameter: 200 mm lower roll diameter: 180 mm bending speed: 5,2 m/min diameter: ca. 280 mm work height max.: 980 mm total power requirement: 5,5 kW weight of the machine ca.: 3500 kg. range L-W-H: 2900 x 1200 x 1280 mm Furnishing: - Robust electro-hydraulic 3-roller bending machine - planetary movement of the bending rollers with reduced center distance - Hydraulic motors combined with planetary gears for driving the 3 rollers - mobile operating unit, with connection cable + plug - extended roll ends for profile bending rolls - with conical bending device Inclination of the side rollers by handwheels Workpiece limitation for a cone with a 45° pitch: Working length max: 60% Bending capacity max: 50% - free-moving operation electric delivery rollers electric turning/rolling movement digital positi ...

Filter cartridge, 5 pieces JIPAP 627962 627 962 114 220 / 627 963 120 103 Inner diameter: Ø · 18 mm outer diameter: Ø 70 mm Total lengths: 150 mm length (filter jacket): 127 mm Flange diameter: Ø 36 / 33 mm ( conical ), Length: 8 mm Other quantities on request ! New ! Dimensions ( single filter cartridge ): 150 x 70 x 70 mm Dimensions ( packaging ): 215 x 155 x 135 mm

Hydraulic pump, gear pump GEC ALSTHOM R.N.U.R.61/U4017-0 318681 Connections: 32 / 57 / 68 mm Flange diameter: Ø 200/ 165 mm bolt circle: Ø 140 mm Shaft guide: Ø 102 / 96 x 80 mm (conical) shaft: Ø 29 mm Inner diameter bearing bush: Ø 50 mm regenerated ! Dimensions: 410 x 385 x 280 mm

Hydraulic pump, gear pump GEC ALSTHOM R.N.U.R.61/U4017-0 318681 Connections: 32 / 57 / 68 mm Flange diameter: Ø 200/ 165 mm bolt circle: Ø 140 mm Shaft guide: Ø 102 / 96 x 80 mm (conical) shaft: Ø 29 mm Inner diameter bearing bush: Ø 50 mm regenerated ! Dimensions: 410 x 385 x 280 mm

Hydraulic pump, gear pump BERARMA SP1NN/2,6R 111.10.026.00 2.2 cm3/revolution max. 250 bar shaft: conical 1/8 keyway width 2.41mm flange: 87 x 68 mm New ! Dimensions: 90 x 70 x 115 mm

Conical round knitter, Fabr.W & P , Type CR 87-3

Conical round knitter, Fabr.W & P , Type CR 87-3

Intermediate flange hydraulic pump VIVOLO, CONTARINI X2P5502ECBA VIVOIL Patent shaft diameter: Ø 15 / 18 mm x 20 mm (conical) shaft thread: M12 x 1.5 Flange diameter: 250 mm bolt circle diameter: Ø 215 mm 4 x bore Ø 14 mm 4 x thread M12 x 1.75 used, tested ! Dimensions: 250 x 250 x 250 mm

Conical round knitter, Fabr.W&P, Type CR 59, mobile,

Hydraulic pump with intermediate flange ROQUET 1L35DE10R shaft diameter: Ø 15 / 18 mm x 20 mm (conical) shaft thread: M12 x 1.5 Flange diameter: 250 mm bolt circle diameter: Ø 215 mm 4x bore Ø 14 mm 4x thread M12 x 1.75 used, tested ! Dimensions: 250 x 250 x 300 mm

Monzesi Rossi Monza 500 centerless grinding Grinding wheel 250 500 auto plunge also available The machine is in our warehouse in Gussago BS, under power Mimu machine tools, Centreless grinding is a procedure for grinding cylindrical bodies and is used for mass production of rollers, cylindrical, conical rollers, jet needles, pump pistons, hydraulic sliders, crosses, drills etc., During centerless plunge grinding, the workpiece is ground in one pass, thanks to the translation of the grinding wheel. For this purpose, the grinding wheels and the adjustment discs have a negative profile of the piece, to work which is given to them with the aid of a tool., The through-feed grinding or also through grinding and longitudinal grinding: pieces, to be worked proceed uninterruptedly with axial feed through the rectification gap.ith axial advancement through the grinding gap.

Hydraulic pump with intermediate flange PARKER, PMD-CHEMNITZ 3349116141 Shaft diameter: Ø 15 / 18 mm x 20 mm (conical) shaft thread: M12 x 1.5 Flange diameter: 250 mm bolt circle diameter: Ø 215 mm 4 x bore Ø 14 mm 4 x thread M12 x 1.75 used, tested ! Dimensions: 250 x 250 x 260 mm

Transnorm belt curve conveyor left GKF 70°-730-600 IR600 RA1936 The Transnorm belt curve is fully functional. It has a gear motor of the brand SEW. Supports and are not included in the scope of delivery. They are optionally available on request. Belt curves are often used in intralogistics for the internal transport of unit loads and are indispensable in modern distribution centers. Transnorm belt curves convince with performance and reliability. Thanks to a low-tension drive over the entire belt width, long operating times are no problem. Conical drums and a specially developed belt guide system ensure the highest possible running smoothness. Technical data: Frame width (NB): 730 mm belt width (GuB): 550 mm height (BH): 210 mm Inner radius (IR): 600 mm Conveying angle: 70° degrees support feet: optionally available Conveying speed (v m/s): freely adjustable with frequency converter b ...

Hydraulic motor, gear motor BONDIOLI & PAVESI MA1-60 shaft: Ø 10 / 8 x 19 mm, conical, thread M6 x 1.0 gear: Ø 25 / 22 x 14 mm, 14 teeth Flange: 86 x 68 mm used, tested ! Dimensions: 115 x 70 x 90 mm

Transnorm belt curve conveyor right GKF 22.5°-850-650 IR1200 RA1523 The Transnorm belt curve is in good condition (used) and fully functional. It has a gear motor of the brand SEW. Supports and are not included in the scope of delivery. They are optionally available on request. Belt curves are often used in intralogistics for the internal transport of unit loads and are indispensable in modern distribution centers. Transnorm belt curves convince with performance and reliability. Thanks to a low-tension drive over the entire belt width, long operating times are no problem. Conical drums and a specially developed belt guide system ensure the highest possible running smoothness. The pictures of the conveyor system shown here were taken in a logistics center while still installed. Technical data: Conveying length middle radius (NL): 726 mm Frame width (NB): 850 mm belt width (GuB): 650 mm  ...

Pressure switch, adjustable LAYHER, ACRON Type 404 4.0-4.5 Pressure range 10 - 70 bar Switching capacity: 42 V 2 A Thread: M10 x1.0, length: 9 mm, slightly conical Width across flats: 27 mm New ! Dimensions: 54 x 29 x 27 mm

Transnorm belt curve conveyor left GKF 70° degrees-770-600 IR600 RA1415 The Transnorm belt curve is in good condition (used) and fully functional. It has a gear motor of the brand SEW. Supports and are not included in the scope of delivery. They are optionally available on request. Belt curves are often used in intralogistics for the internal transport of unit loads and are indispensable in modern distribution centers. Transnorm belt curves convince with performance and reliability. Thanks to a low-tension drive over the entire belt width, long operating times are no problem. Conical drums and a specially developed belt guide system ensure the highest possible running smoothness. The pictures of the conveyor system shown here were taken in a logistics center while still installed. Technical data: Conveying length middle radius (NL): 1100 mm Frame width (NB): 770 mm with Motor 940 mm be ...

Hydraulic pump, gear pump XUGRABLUKA A18X Nominal pressure: 175 bar Nominal speed: 1500 rpm shaft: Ø 15 / 17 mm, length: 22 mm, conical groove width: 3 mm thread: M12 x 1,5, Length: 12mm Flange: 90 x 114mm hole spacing: 72 / 96 mm 4x bore: Ø 7.2 mm used, tested ! Dimensions: 135 x 90 x 115 mm

Hydraulic pump, gear pump INDUSTRIALTECHNIC SC C72X Nominal pressure: 175 bar shaft: Ø 19 / 22 mm, length: 28 mm, conical groove width: 4 mm thread: M14 x 1,5, Length: 12 mm Flange: 118 x 147 mm hole spacing: 98 / 128 mm 4x bore: Ø 9 mm New ! Dimensions: 170 x 118 x 147 mm

Transnorm right flush roller conveyor 3470-1830-1450 RA1855 Make: Transnorm Basic dimensions: conical structure, 3470x1160-1830 mm Length: 3470 mm Nominal/external width (NB): 1160-1830 mm Roll length (RB): 160-450 mm & 640-1000 mm Frame height: 290 mm Currently set height: 640 mm Height of side guide: 410 mm Width (height) side belt 300 mm Roller diameter: 50 mm Roller pitch: 65 mm Including 8 feet Motor MOVI-Mot 3x300-500V 1,5kW Conveying speed: Features: Construction year: 2017 Conveying length in mm (NL): 3470 Optional erhältlich: Frequenzumrichter Electric data: 70Hz, 217 / 375 V Antrieb: Nord-Drivesystem Supports: 8 Bauhöhe in mm (BH): 290 Belt width in mm (GuB): 300 Height in mm: 640 Galvanized rollers: Ø = 50 mm scope of delivery: including supports and side guides, Kabel, ohne Frequenzumrichter Roll width in mm: 160-450, 640-1000 condition: Ausstellungsstück Roll division i ...

Hydraulic pump BOSCH AZPF-11-005LHO30MB 0 510 325 308 ( 0510325308 ) shaft: Ø 15 / 17 mm, length: 22 mm, conical groove width: 3 mm thread: M12 x 1,5, Length: 12 mm Flange: 88 x 113 mm used, tested ! Dimensions: 130 x 90 x 115 mm

Transnorm belt curve conveyor left GKF 45°-1370-1200 IR1100 RA1937 The Transnorm belt curve is fully functional. It has a gear motor of the brand SEW. Supports and are not included in the scope of delivery. They are optionally available on request. Belt curves are often used in intralogistics for the internal transport of unit loads and are indispensable in modern distribution centers. Transnorm belt curves convince with performance and reliability. Thanks to a low-tension drive over the entire belt width, long operating times are no problem. Conical drums and a specially developed belt guide system ensure the highest possible running smoothness. Technical data: Frame width (NB): 1370 mm belt width (GuB): 1200 mm height (BH): 260 mm Inner radius (IR): 1100 mm Conveying angle: 45° degrees support feet: optionally available Conveying speed (v m/s): freely adjustable with frequency conve ...

Straight compression fitting, compression fitting, screw-in fitting, 8 pieces LANDEFELD 7x KGE 1212 KON MS Pipe outer diameter: Ø 12 mm < br /> 1x KGE 1210 KON MS Pipe outer diameter: Ø 10 mm screw-in thread: R 1/2 ( inch, conical ) Material: Brass 19 / 22 mm, 17 / 22 mm with nut and clamping ring Other quantities on request ! New ! Dimensions ( single screw connection ): 48 x 25 x 22 mm

Hydraulic pump RZESZOW HYDRAULIK PZ - 10 ( PZ-10 ) shaft: Ø 13 / 15 mm, length: 18 mm, conical groove width: 3 mm thread: M10 x 1,5, Length: 8 ( 13 ) mm Flange: Ø 63 / 78 x 110 mm hole spacing: 60 / 90 mm hole diameter: Ø 7.0 mm New ! Dimensions: 132 x 80 x 110 mm

Transnorm belt curve conveyor left GKF 45°-750-550 IR700 RA1451 The Transnorm belt curve is in good condition (used) and fully functional. It has a gear motor of the brand SEW. Supports and are not included in the scope of delivery. They are optionally available on request. Belt curves are often used in intralogistics for the internal transport of unit loads and are indispensable in modern distribution centers. Transnorm belt curves convince with performance and reliability. Thanks to a low-tension drive over the entire belt width, long operating times are no problem. Conical drums and a specially developed belt guide system ensure the highest possible running smoothness. The pictures of the conveyor system shown here were taken in a logistics center while still installed. Technical data: Type designation: Belt curve conveyor TS 1600-105 Conveying length middle radius (NL): 680 mm Fram ...

Hydraulic pump, gear pump CASAPPA PLP20.14S0 PLP20.14S0-54B2-LBE/BC-N-EL-FS 01999956 shaft: Ø 14 / 18 mm, length: 22 mm, conical groove width: 3 mm with shaft thread: M12 x 1.5, length: 10 mm flange: Ø 80 / 90 x 120 mm hole spacing: 72.5 / 100 mm 4x bore: Ø 9.5 mm New ! Dimensions: 146 x 90 x 120 mm

Tailstock PAGUS Center height: 165 mm Tool holder: Outer diameter: Ø 78 mm, co-rotating Tool holder: Inner diameter: Ø 58 / 53 mm, length: 105 mm, conical Push-out screw with handwheel Guide bushing: Inner diameter: Ø 30 mm, length: 125 mm used, tested ! Dimensions: 305 x 203 x 217 mm

Transnorm belt curve conveyor 90° degree right GKF 90°-750-550 IR600 RA1408 The Transnorm belt curve is in good condition (used) and fully functional. It has a gear motor of the brand SEW. Supports and are not included in the scope of delivery. They are optionally available on request. Belt curves are often used in intralogistics for the internal transport of unit loads and are indispensable in modern distribution centers. Transnorm belt curves convince with performance and reliability. Thanks to a low-tension drive over the entire belt width, long operating times are no problem. Conical drums and a specially developed belt guide system ensure the highest possible running smoothness. Technical data: Type designation: Belt curve conveyor TS 1600-105 Conveying length middle radius (NL): 1805 mm Frame width (NB): 750 mm belt width (GuB): 550 mm height (BH): 210 mm Inner radius (IR): 600 m ...

Planscheibe ROTO RECORD PL 315x5 ( PL315x5 ) TGL 30-22313 n: max. 7100 rpm outer Ø: 315 mm height with jaws: 125 mm bolt circle Ø (chuck) : 105 mm bore Ø: 78 mm mounting flange: Ø 79 / 81 mm, depth: 13 mm ( conical ) groove width: 14 / 24 mm groove depth: 24 mm with one-piece reversing jaws used, tested ! Dimensions: 315 x 315 x 125 mm

Planscheibe ROTO RECORD PLV 400x8 ( PLV400x8 ) TGL 30-22313 / n: max. 650 rpm outer Ø: 400 mm height with jaws: 135 mm bore Ø: 108 mm bolt circle Ø (chuck) : 172,5 mm 4x threaded hole: M16 x 2.0, depth: 45 mm mounting flange: Ø 135 / 140 mm, depth: 18 mm (conical ) groove width: 14 / 25 mm groove depth: 24 mm with one-piece reversing jaws and 2x lathe chuck wrench used, tested ! Dimensions: 405 x 405 x 135 mm

Chuck flange, intermediate flange for lathe chuck PAGUS Outer Ø: 200 mm bolt circle (lathe chuck side): Ø 133,5 mm flange (lathe chuck side): Ø 106 / 103 x 14.4 mm (conical) bolt circle (machine side): Ø 174 mm flange (machine side): Ø 101 x 25 mm used, tested ! Dimensions: 200 x 200 x 52 mm

3-jaw chuck, three-jaw chuck, power chuck, wedge hook chuck with adapter PAGUS outer diameter: Ø 200 mm bolt circle diameter (lathe chuck) : Ø 150 mm bolt circle diameter (adapter): Ø 180 mm Flange diameter (adapter) : Ø 140 / 135 x 19 mm (conical) height with adapter: 147 mm without jaws ! used, tested ! Dimensions: 200 x 200 x 240 mm

Abrasive holder, grinding wheel holder REISHAUER RZ 62 / 84 inner diameter abrasive : Ø 160 mm mounting hole: Ø 34 / 58 x 78 mm ( conical ) used ! Dimensions: 240 x 240 x 115 mm

Transnorm belt curve conveyor left GF 45°-750-550 IR700 RA1390 The Transnorm belt curve is in good condition (used) and fully functional. It has a gear motor of the brand SEW. Supports and are not included in the scope of delivery. They are optionally available on request. Belt curves are often used in intralogistics for the internal transport of unit loads and are indispensable in modern distribution centers. Transnorm belt curves convince with performance and reliability. Thanks to a low-tension drive over the entire belt width, long operating times are no problem. Conical drums and a specially developed belt guide system ensure the highest possible running smoothness. The pictures of the conveyor system shown here were taken in a logistics center while still installed. Technical data: Type designation: Belt curve conveyor TS 1600-105 Conveying length middle radius (NL): 766 mm Frame ...

Tool holder for threaded screw-in milling cutter, 3 pieces POKOLM 2x 75 12 750 100 12 750 SK 40 thread M12 usable length: 2x 75 / 100 mm conical design inner coolant supply used, tested ! Dimensions ( single tool holder ): 163 / 188 x Ø 64 mm Dimensions ( packed ): 250 x 140 x 70 mm

Tool holder for threaded screw-in milling cutters, 3 pieces POKOLM 50 16 750 75 16 750 100 16 750 SK 40 thread M16 usable length: 50 / 75 / 100 mm conical design internal coolant supply used, tested ! Dimensions ( single tool holder ): 138 / 163 / 188 x Ø 64 mm Dimensions ( packed ): 260 x 140 x 70 mm

Tool holder for threaded screw-in milling cutter, 2 pieces POKOLM 75 16 750 100 16 750 SK 40 thread M16 usable length: 75 / 100 mm Conical design inner coolant supply used, tested ! Dimensions ( single tool holder ): 163 / 188 x Ø 64 mm Dimensions ( packed ): 250 x 120 x 70 mm

Tool holder for threaded screw-in milling cutters POKOLM 250 16 750 SK 40 thread M16 usable length: 250 mm conical design inner coolant supply used, tested ! Dimensions: 338 x Ø 64 mm Dimensions (packed): 350 x 70 x 70 mm

Tool holder for threaded screw-in milling cutter, 3 pieces POKOLM 2x 75 10 750 100 10 750 SK · 40 thread M10 usable length: 2x 75 / 100 mm Conical design internal coolant supply used, tested ! Dimensions ( single tool holder ): 163 / 188 x Ø 64 mm Dimensions ( packed ): 250 x 140 x 70 mm

Tool holder for threaded screw-in milling cutter, 2 pieces POKOLM 50 08 750 ZYL Cylindrical design 75 08 750 Conical design SK 40 thread M10 usable length: 50 / 75 mm inner coolant supply used, tested ! Dimensions ( single tool holder ): 138 / 163 x Ø 64 mm Dimensions ( packed ): 200 x 110 x 70 mm

Test mandrel, control mandrel PAGUS 188354 187314 mandrel: Ø 50 x 310 mm Cantilever length ( A-dimension ): 370 mm Flange diameter ( inner ): Ø 103 / 106 x 14 mm ( conical ) Flange diameter ( outer ): Ø 175 x 50 mm bolt circle diameter: Ø 150 mm hole diameter: Ø 10.5 mm with wooden box used, tested ! Dimensions ( wooden box ): 425 x 225 x 205 mm Dimensions ( test mandrel ): 370 x 175 x 175 mm

Test arm, control arm PAGUS 189097 arm length ( without dial gauge holder, from flange center ): 257,257,5 mm arm cross-section: 20 x 20 mm dial indicator: Ø 8 mm Flange diameter ( inside ): Ø 79 / 82 x 14 mm ( conical ) Flange diameter ( outside ): Ø 130 x 77 mm bolt circle diameter: Ø 112.5 mm hole diameter: Ø 8.5 mm with wooden box used, tested ! Dimensions ( wooden box ): 420 x 185 x 135 mm Dimensions ( test arm ): 345 x 175 x 77 mm

Power chuck, 3-jaw chuck, three-jaw chuck, wedge hook chuck KITAGAWA B-208 Outer diameter: Ø 210 mm Height without jaws: 105 mm Passage: Ø 52 mm Speed: max. 5000 rpm Flange diameter 1: Ø 170 mm Flange diameter 2: Ø 103 / 105,5 mm x 17 mm ( conical ) bolt circle diameter: Ø 134 mm 6x through bore: Ø 13.0 mm jaws individually adjustable by toothing ! with accessories ! New, with documents ! Dimensions ( lathe chuck ): 210 x 210 x 105 mm Dimensions ( packaging ): 290 x 250 x 240 mm

Angle screw-in fittings, with conical external thread, 9 pieces GRESSEL SERTO SO 2421-15-1/2 Pipe outer diameter: Ø 15 mm screw-in thread: R 1/2 Material: Brass New ! Dimensions(Single): 60 x 45 x 27 mm Dimensions(Packaging): 140 x 90 x 60 mm