concrete mixing plant used for sale

The combined cycle plant consists of a gas turbine, waste heat recovery boiler, steamturbine and a generator, mounted in a single shaft configuration. The capacity of the installation is 53 MW • The prime mover of the installation is an aero derivative General Electric LM6000-PB-DLE. 40 MW - 30,000 hours remaining till next major overhaul - Running hours 74.100 hours , start 3356 - Next overhaul in 5000 hours(hot gas path) - Next major overhaul: in 30.000 hours • The Steam Turbine is a SIEMENS ENK40/53-3, with a capacity of 13 MWe. Dismantled, stored and ready for transport.

Painting cell with ABB robot Year of construction: 2016 Robot ABB IRB 1600 Payload: 6 kg Arm area: 1200 mm Control: IRC5 Number of axles: 6 Axis range: J1 +180° – 180° J2 +136° – 63° J3 +55° – 235° J4 +200° – 200° J5 +115° – 115° J6 +400° – 400° Turntable Suction Automatic V5 HVLP paint sprayer DO Combo Diaphragm Pump

Osmosis plant TKA TKA RO 60DS Osmosis water production Reverse osmosis with 300L tank. Reference TKA RO 60DS

ID3275 Shore Belt Plant/Conveyor System year approx. 1995-2000? Approx. 470 m conveyor belt system, with covers, off-road, ascending with roadway crossing, fully hot-dip galvanized, year of construction unknown - probably 1995-2000. Estimated active working time approx. 10 years. Length approx.: 470 m, intended belt width 500 mm, discharge and drive-through height approx. 5.7 m, without conveyor belt, dismantled in transportable units, discharge station with railing and walkway, drive power 18.5kW approx. 470 m land conveyor system, with covers, following the terrain, ascending with road crossing, fully hot-dip galvanized, year of construction unknown - probably 1995-2000. Estimated active service life approx. 10 years. Length approx.: 470 m, intended belt width 500 mm, discharge and drive-through height approx. 5.7 m, without conveyor belt, dismantled in transportable units, dischar ...

re-granuling-line for PO-films

Venjakob year of manufacture 1999 Spray guns 4 Water based paint and lacquer and also UV paint acid curing paint? – Not possible now, but can be done, if we change pump, tubes and nozzles Paint recycling - yes Is it possible to apply bets”? Water based? – yes, water based Are the work pieces stackable directly after they come out from the line? (Are they dry so they can be stacked?) – Yes, if we use UV- water based paint but when using normal water based paint or lacquer components must be dried in a shelf What type of products do you run in the line? What materials? – MDF, melamine surfaced doors, components etc. and solid wood components (mainly birch) What are the dimension limitations for the work pieces? – width min/max 20-1200 mm, lenght min/max 350-2750 mm, thickness max 50 mm Spraying machine Venjaob HGS-Duo Venjakob VEN SPRAY DUO Lacquering line sand paint IR UV dry ...

Description Plastic Regranulation Line Extruder diameter 106 L/D 35 Vent Feeding Silo Screen changer Machine stoped for upgrading to a new version. Worked till arrive of the new one.

Description Regranulation Line complete of granulator Extruder Diameter 60 L/D 35 Silos for forced feeding of film Granulator 35/45 Vent Screen changer Centrifuge

Description Regranulation line for polyolefins Screw diameter 85 Nr.1 Vent Spaghetti granulation head Hydraulic screen changer Cooling tank Pelettizer

100 % before loading warranty: none

Welding current range : 150A/26V - 1000A/44V; with carriage, type: TR1501; with digital readout; including control cable, length approximately; 15 meters and intermediate pack and ground cable

Used bread line W&P -Refurbished- 1) Haton CR-59 Kegerundwirker, heated, lubrication, frequency control, automatic slide 2) Haton AF 2002 proofer, fully automated, digital control 3) Conveyor belt 4) Haton Combi U long roller table, very flexible 5) By-Pass tape to bypass the proofer, directly to the Combi U long roller The entire line is completely overhauled and in perfect condition! Warranty 6 months Please note: The V-300 dough divider is not part of this offer as it is already sold! Alternatively, a RHEON VX 202 Twin Divider can be offered for high-quality Artisan products.

Bottle Filler and crown capper, make Krones, type: Mecafill VK2V 024-188/KK, 24 filling valves, Vacuum pump, Hot water injection before closing, 6 head bottle cap closing, Crown Cork feeder, electr. height adjustment, direction: counter clockwise / right to left, with Siemens S7 Simatic ET200M, built 1998

Bottle filler, make. KHS, type: VVF-90-KK16-SV16, with 90 filling valves, with 16-head crown cork and 16-head screw capper, built 1989

Analog control; incl. filling station; Length of grease pan: 3,000 mm;

Bottle filler, make Krones, type: VKS 84 / SV 12-094 RM, for lemonade and mineral water 24.000 bph, with 84 filling valves (mechanical with float control), with 12-head screw capper make Zalkin, for MCA 28 aluminum caps, right machine, built 1992

Vacuum filler, make SEN, with 28 filling valves, with 5-head screw capper for MCA 28 caps.

Vacuum filler, make SEN, type: Compacta FWF 30/6, for about 5.000 bph, with 30 filling valves and 6-head nature corker, adjust to 0,7 lt / 0,75 lt "Bocksbeutel"- and 1,0 lt wine bottle, built 1985

Bottle filler, make Pirzer, type: Nova, long pipe filler with 20 filling valves, with crown capper, built 1981

Bottle Filler, make WüMa, typ: BAD 20/4, with 20-valve pressure filler and 4-head crown capper, built 1977

Bottle filler, make ICS, type: TPS 24/6K, with 24 filling valves and 6-head crown capper, adjust to 0,5 lt. NRW- and Euro-bottles, built 2002, was in operation until the end of 07/2022

Pipe diameter: 219mm, nominal width: 3600mm, including preheating oven, Blasting System GIETART GW 1530-425, centrifuge, coating center, drying tunnel, chain conveyor and color filter, operational hours: ca. 8,000h.

Vacuum Filler, make Vir Mauri, type: PAVON / S.12.DP, with 12 filling valves, in stainless steel, in good condition.

Vacuum filler, make MerCori, type: DGF 18-6, for 3.000 bph, with 18 filling valves and 6-head screw capper, built 2010, Length: ca. 2,0m, Width: ca. 1,7m, Height ca. 2,20m.

Vacuum chamber volume: 0.62m³, weight: 2800kg, cooling water requirement: 700l/h. On-site inspection is possible.

Drive power: 110kW, with reversing Film Take-Off Kirion T 1300, Monoblow Head Kirion 120/300-1, further accessories and documentation.

Vacuum filler, make Zimec, with 40 filling valves, with separate 5-head screw capper make Bertolaso, with sorter make Adelski on the machine (no more in operation), with second sorter besides standing for BvS 30/60 caps, built 1994

PET-Filler, make: H&K, type: VVF112/14SV, with 112 Filling valves, with 120 mm pitch, with 14-head screw capper make Alcoa für PCO 28 caps, built 1985

Was used for filling and packing flour and sugar, format: 1000g, max. output: 90/ min, with mandrel, main dosing unit, Glue Applicator NORDSON, check weigher and post doser.

Was used for filling and packing flour, format: 1000/ 2000g, backset: 105x65mm, max. output: 1/ 2kg packages: 60/ 50/ min, controls: ELAU MC4, with 3x servo main dosing unit, check weigher and servo post doser.

System includes receiver tank, agitator, expansion tank, sealing water tank, equalising tank, centrifugal pump, side channel pump, vacuum liquid ring pump, tubular heat exchanger, condenser, plate cooler, sight glasses, fittings, permanent magnet and filter, with documentation.

System includes receiver tank, agitator, expansion tank, sealing water tank, equalising tank, centrifugal pump, side channel pump, vacuum liquid ring pump, tubular heat exchanger, condenser, plate cooler, sight glasses, fittings and permanent magnet, with documentation.

Volume: 400l, max. permissible pressure: -1.0bar, min.-max. temperature: 10°C-90°C, test pressure: 0.1bar. External dimensions X/Y/Z: approx. 1500mm/2400mm/2600mm, weight: approx. 1500kg. Completely overhauled and hardly used since. On-site inspection is possible.

Brand: Krones Year of construction: 1986 Capacity: 30,000 bph Operating hours: approx. 50-55,000 (34 years in single-shift operation) Formats: Euro 0,5l beer bottle, NRW 0,5l beer bottle, Steinie 0,33l beer bottle, Alaska 0,5l individual bottles for lemonades/juices Seaper: 1. Crown cap / 2. Ring pull / 3. Screw cap The control has been converted to S7. The main drive is almost new.

System includes (1) Two-Cylinder Motor HERFORD 2H 280, power: 150PS, rotational speed: 400/min, electric/ heating power: 83/ 140kWh, with Generator MARELLI MJB 250 LE4 (2) Three-Cylinder Motor HERFORD 3H 280, power: 225PS, rotational speed: 400/min, electric/ heating power: 125/ 212kWh, with Generator MARELLI MJB 250 MA4.

Operating pressure: 10-20bar, weight: 1.33t, with buffer storage, pumps and external heat exchanger.

Combined heat and power unit has been converted for continuous operation. Output: 225kW at 1500 rpm. Fuels: diesel/fuel oil.

Electrical output: 5.5kW, thermal output: 14.8kW, power consumption: 20.5kW. Max. Flow temperature: 95°C, max. return temperature: 70°C, operating pressure: 5bar. Dimensions X/Y/Z without controller: approx. 1000mm/720mm/1070mm, weight: 530kg, operating hours: 66773, fuel: natural gas. Including condenser and MSR 2 control. Documentation available.

System includes (1) Dekanter FLOTTWEG X4E-4/ 454, output: 30m³/h (2) Sludge Pump NETZSCH AGNM02 (3) Polymer Pump NETZSCH, as well as thick matter pump, polymer dosing pump, flow measuring devices and additional elements, operational hours counter: 7919h. Max. Operating current 63A, as the main switch in the control cabinet is rated for 63A. A 125A CEE supply line is required for operation.

Bottling line isobaric PET/glass Year: 2000 - 2013 Speed: PET: 6.000 bph Vetro: 8.000 bph Blower SIAPI - 2000 Preform tilter – 2012 ZECCHETTI air conveyors – 2000 Depalletizer SYMPAK - 2003 Filling monoblock BC 42.50.10 – 2000 Ozonator – 2000 Caps elevator – 2000 Deareator and Saturator BC– 2000 Labeller KOSME cold glue and hot melt for glass – 2000 Labeller P.E. hot melt for PET - 2003 Bottle inspector (cap level label) – 2000 Inkjet VIDEOJET – 2013 Devider (1 to 2 rows) – 2003 Shrink wrapper DIMAC – 2000 Handler TWINPACK – 2000 Wraparound DIMAC – 2003 Box conveyors - 2003 Palletizer KEBER – 2000 Pallet wrapper – 2000

Bottling line – Isobaric Speed: 6.000 bph Rinser AVE 28 clamps Single treatment Fixed nozzle Filler Bertolaso 32 valves De-gassing Self-leveling Pre-evacuation Corker BERTOLASO 4 heads Natural straight cork Capper BERTOLASO 3 heads Screw cap Capsuling machine NORTAN 4 heads for pvc capsules Plateau capsules distributions Ruller BERTOLASO – 8 heads Labeller KOSME – cold glue Box forming machine APE Case packer APE Box closing machine APE Palletizer APE

Volume: 1.5m³, max. cleaning capacity: 250l/min, air consumption: 12m³/d, operating pressure: 6bar, collection tank capacity: 1200l, dimensions X/Y/Z: 2121mm/1339mm/3076mm, weight: 610kg. Documentation available. On-site inspection is possible.

Bottling line PET ISO | 15.000 bph Year: 2001 – 2012 Blowing machine SMI SR10 | 2010 Formats of 05L-1L-1.5L Cap 28 mm PCO CORVAGLIA e 267 NOVEMBAL ALASKA 10 cavities Filling monoblock MELEGARI 50.70.10 | 2001 Rinser 50 clamps Filler 70 valves | isobaric Capper 10 heads Carbonator MELEGARI Labeller P.E. rollfed | 2012 12 heads Shrink wrapper SMI SK 600F | 2001 Handler SMI MAB 60 | 2001 Palletizer EMMETI | 2001 Air conveyors ZECCHETTI | 2001 Safety protections on all machines

Bottling line ALFIERI | PET Year: 1996 – 2001 Speed: 8.000 bph Direction: Counterclockwise Filling monoblock ALFIERI 24.24.8 | 2001 Rinser 24 clamps Filler 24 valves Capper 8 heads AROL Labeller P.E. | 1996 8 heads Nr.1 HOT MELT station Saturator METALOCAIMA mod. RSP

Working width: 2000mm, usable length dryer: 4000mm, production speed: 5-25m/min, speed: 0-30m/min, polyamide powder application quantity: 25g/m², infrared heating output: 2x 40kW + 2x 3kW, length: 13,000mm, operational hours counter: ca. 16,000h, with documentation, without spare parts, was maintained regularly.

Filling monoblock CUSTOM 12.16.1 | Isobaric Year: 2000 Speed: 1.000 bph | champagne 2.000 bph | still wine Direction: Clockwise Rinser 12 clamps Filler 16 valves | isobaric De-gassing Single head corker | natural straight cork and mushroom cork Safety protections

Filling Monoblock BORELLI | COMPACT Year: 1995. Speed: 1.400 bph. Direction: Clockwise. Filler 10 valves. Single head corker | natural straight cork. Safety protections.

filling monoblock BERTOLASO 48.60.12 Year: 1997 Speed: 13.000 bph Direction: Clockwise Rinser 48 clamps Fixed nozzle Double treatment Filler 60 valves Corker 12 heads. Natural straight cork. Safety protections

Filling monoblock ALFATEK 24.4 Year: 2003 Speed: 4.000 bph Direction: Clockwise Filler 24 valves Corker 4 heads – Natural straight cork Safety protections

Triplex solventless Laminator, The machines of 2018 are like new. Only about 200 hours Matrial for lamination : PP, Bopp, Pet ,laminates ,LDPE, LLDPE. web width =1530 mm Max lamination width = 1515 mm, Min. film width = 750 mm, Min. film width with extensions = 550 mm, diameter unwinder = 1000 mm, sleeve 76 / 152 mm, diameter rewinder = 1200 mm, sleeve 152 mm Speed = 450 m/min, Accessories: The machine has many accessories such as 2 mixing plants World Mixer SL 1 Cleaner SL