con pro used for sale

technical details: - suitable for heavy starting machines - 18 l large tank = long running time - electronic voltage regulation (AVR) - Thermo-magnetic circuit breaker against overload and short circuit due to defective loads and cables - Insulation monitoring = safe personal protection - Oil deficiency shutdown - E-Start = high comfort Metrics: - Length: approx. 842 mm - Width/depth: approx. 523 mm - Height: approx. 557 mm - Weight: approx. 96 kg Drive: - Engine: Honda GX 390 - Power factor: 0.9 cos ɸ - Starter: E-Start / Hand Start - Type of fuel: Gasoline - Tank capacity: 18 l - Consumption at 75% load: 2.2 l/h - Sound pressure level Lp: 72dB(A) - Sound power level Lw: 97 dB(A) Generator: - Type: Synchronous - Rated voltage: 230 V - Apparent power at LTP: 7.2 kVA - Active power at LTP: 6.4 kW - Apparent power at COP: 6.0 kVA - Active power at COP: 5. ...

Profisafe, Input/Output, 6ES7 138-4FC01-0AB0, Siemens, new Please note: This is an original product and not a replica from... Special price If you have a VAT number, we will be happy to issue you with an invoice without VAT. New! - never been used and is completely new, - comes from a spare parts warehouse of a certified production facility, - is in its original packaging, 6 months warranty We give you 6 months warranty for these goods from the date of invoice. In case of any defect, which is not the fault of the buyer, the goods can be returned. We will refund the buyer only the product price paid to us. Updating in case of digital components is excluded. Also excluded is liability for direct and indirect consequential damages. Our terms and conditions apply, see our website. Austrian law applies without exception and court location St. Pölten.

Shrink Wrap, Front shuttle feeder, Rotary side feeder, Friction feeder, Shrink tunnel, Maximum Speed: 85 cycles per minute, Length: 85 to 395 mm, Width: 85 to 300 mm, Height: 2 to 70 mm

Offer oil level probe for sale.

Used complete production line for yellow cheese, made by TEWES-BIS Poland. New 2019. Production line for yellow cheese, e.g. Gouda, Edam, Dutch type. Daily capacity: Processing up to 180,000 litres of milk per day. TECHNOLOGICAL SPECIFICATION (MAIN MODULES): Section 1: Preparation of cheese milk: o Milk repasteuriser with a capacity of 15 m³/h. Section 2: Preparation of cheese curds: o Cheese boiler with a capacity of 12 m³. o Hot water generator for boilers. o Process water pasteuriser (5 m³/h) with a 10 m³ tank. o Set of process pumps (whey, curd) with a capacity of 25 m³/h each. Section 3: Cheese room – Moulding and pressing: o Curd buffer tank (10 m³) with pump. o Under-mould forming device (UFP) for Dutch cheese. o Complete mould circuit (300x500x100) with cover applicator and remover. o Final pressing system: 144 pressing points. o Tunnel mould washe ...

Used SJ 50/30 filament production line equipped with an air-cooled head. Technical parameters: - screw diameter 55 mm - L/D 30, effective screw length 1500 mm - Screw rotation speed: 60 rpm - forced feed unit for raw material to the plasticizing system with a power of 1.5 kW / vertical screw system with cylinder . - Main drive motor power 12 kW - capacity approx. 50 kg/h Heating sections and power : - Cylinder 6 kW / three heating sections plus head - Head connector / mechanical screen exchanger with a power of 2 kW - Air cooling of the cylinder and head / motor with a power of 0.18 kW - Raw material: PP/PE ABS/PLA/PETG plastics Weight approx. 800 kg.

FOM INDUSTRIE profile machining center was built in 2009 by F.O.M. INDUSTRIE s.r.l. This machine, designed for precision machining of PVC profiles, is an excellent choice for businesses specialising in the manufacture of windows. It enables, among others, milling, cutting or making ventilation and holes for the handle. Window profiles are machined by means of various types of aggregates. The standard machine in this series has 14 aggregates, however, the machine in our offer has been equipped with additional milling and drilling aggregates and has a total of 18 of them. This solution significantly increases the machining capacity of the machine as well as the overall machining efficiency. The FOM INDUSTRIE PVC profile machining center is also extremely easy to operate. All machining parameters are programmed in the intuitive CNC control with graphic software. Technical specifications  ...

Used mozzarella production line. New 2013. The line includes: - Tank for preliminary pressing of cheese curd - LT150 thermizer - Molds for shaping the curd - Chilled water tanks - Brine tanks - Tube heat exchanger for cooling brine Cheese curd plasticizing set consisting of: Tanks for pre-pressing cheese curd with an automatic device for cutting into small portions. The prepared cheese curd is fed into the thermizer for plasticization. The plasticized mass is manually formed into cheese molds. The portions prepared in this way, packed in molds, are cooled in an ice water tank. After cooling, they are removed from the molds and placed in brine tanks. After salting, the mozzarella blocks are sent to a ripening room with specific temperature and humidity parameters.

General: Year of construction 2013 Control Fanuc Series 0i-MD Travel X 703 mm Y 603 mm Z 503 mm Working spindle 12,000 rpm Tool changer 40-fold Tool holder DIN40 Specifications: Table swivel +31.1° / -121.7° Table rotatable 360° Other equipment and accessories included: Preparation 3D probe

Scissors for reinforcing steel or bars max 32mm

Mobile container heating system Year of construction 2023 Original price: 178.500,- € gross Boiler Buderus GE615 Power: approx. 511–570 kW Burner Weishaupt WM-L10/3-A Monarch Oil burner (tbsp heating oil) Regulation Buderus Logamatic 5311 Other components Two large heating buffer tanks Chimney outside Hydraulics complete in the container Connection cables for heating network Location of the machine: 76661 Philippsburg The facility can be visited on site. It is still energized and works perfectly. You can make an appointment for a viewing at any time before bidding on +49 (0) 72 55 / 39 73 337. We would love to hear from you. We will be happy to answer any questions you may have at any time. We are looking forward to a good cooperation and thank you for your interest in advance.

Lid Maho DMC-200 U serie 1512 5-axis CNC universal machining center, simultaneous Control: Heidenhain iTNC 530 Table size: 1600x1400 mm Table load: 3500 kg Number of pallets: 2 x Maximum workpiece diameter x height: 1950x1100 mm Travel X-axis: 1800 mm Travel Y-axis: 2000 mm Travel Z-axis: 1100 mm C-axis table rotation: 360° B-axis travel: -7/187° Spindle speed: 18000 1/min Spindle cone: HSK-A63 Spindle motor: 28/19 kW Magazine capacity: 120 Required footprint: 11200x12300 mm Height: 4375 mm Weight: 58000 kg For any questions about the machine, as well as a scheduling for the inspection, we ask you to contact us by phone or e-mail.

PVS -Micro-Cut or emulsifiers. Formerly called Kolidmühle For shredding various products Production of emulsions Pastes Sauces Soups and various other products Capacity up to 150 litres Motor power 15 KW

Diesel-Generator Power: 500 kVA Year: 1997 Operating hours: 49612 Generator: Stamford HC I534D1 Speed: 1500 1/min Voltage: 400/231 V, 50 Hz Battery voltage: 24 V 20 ft container Weight: 8.5 tons Manual switchgear with motor monitoring Subject to prior sale - errors possible! Internal reference number: E-1004-49

Horizontal machining center Kafo HVC 500 :::SPECIFICATIONS::: CNC Model: Fanuc CNC version: 18i MB Tool connection: BT 50 Spindle power: 25Kw Number of spindle revolutions: 10000 Number of tools: 60 X Shaft Stroke: 720mm Y Axis Stroke: 650mm Z Axis Stroke: 650mm Rapid feeds linear axes X Y Z: 48m/min Pallet size: 500x500mm Pallet type: indexed Pallet degrees: 0.001 Maximum load allowed: 800Kg High cooling pressure: yes Pressure value: 20bar System with external tank with filter: yes Chip evacuator: carpet :::D IMENSIONS AND WEIGHT::: Length: 4035mm Width: 5170mm Height: 3000mm Weight: 13000Kg

Power: 850 kVA Fuel: Diesel Frequency: 50 Hz Voltage: 400/231 volts Operating hours: 75 40 ft container Control cabinet incl. wiring diagrams 750 liter tank No exhaust Subject to prior sale - errors possible Internal reference number: E-1156

Key data: 825 , 975 , 400

Steam turbine Generator CCC CFR 3 G5 780 KWe x 1,500 rpm 50 Hz 400 V Turbine backpressure Manufacturer KKK Model CFR 3 G5 P drive [KW] 780 Vapor pressure [bar] 39 - 48 / 43 norm Exhaust pressure [bar] 7 - 9 / 7,85 norm Generator Manufacturer AVK Model DKBN 100M/1100-4 P Generator [KVA] 975 Revolutions [per min] 1,500 Voltage [V] 400 Current [A] 1,407 Scope of delivery: The genset consists of the turbine and the generator. Technical documentation: available Spare parts / tools: not available The genset was dismantled in a working condition Sale takes place "as is" or after prior inspection on request, FCA free.

Wir bieten Ihnen eine gebrauchte MIWE Gäranlage an. T:179 cm (mit Türen, 181 cm (mit Griff) - Steuerung ragt zusätzlich 15 cm heraus B: 93 cm H: 224 cm Aggregat an der Decke. Die Gäranlage ist für 2 Rotationswagen mit Platten 60x80 cm oder 1 gewöhnlicher Wagen (180 cm) mit Platten für 100 cm. Preis noch festzulegen - bitte kontaktieren Sie uns.

Profile steel shears

Pressure measuring device, flow measuring device, measuring and control technology, flow meter -Manufacturer: Brigon, accessories pressure measuring devices -Measuring liquid: green HDM -Measuring range: up to 30 mbar -Dimensions: 95/50/H385 mm -Weight: 0.6 kg

Finishing unit, modular unit, format processing unit, double-end tenoner, edge processing machine, scraper for edge processing machine -Manufacturer: Homag, profile scraper from edge banding machine BRANDT KM 36 / KM35 -Quantity: 1 piece available -Dimensions: 510/430/H570 mm -Weight: 62 kg

Central unit, control system, switchgear, CPU, PLC -Manufacturer: B&R Bernecker & Rainer, Minicontrol with Control Panel -Product number: MCGE33-0 -Individual components: see photos -Overall dimensions: 255/130/H220 mm -Weight: 2.3 kg

2 identical diesel gensets available MWM TD602V16 AvK generator with 700 kVA Operating hours approx. 1200 per unit Incl.: Radiator Silencer Cabinets Technical documentation Disassembled and immediately available Subject to prior sale - errors possible Internal reference number: E-1159

WEBER COOLING BASE TWO Vacuum cooling system Cooling capacity: 2 IP or 2 EUR Products to be cooled: leafy vegetables/fruits up to 1000 kg Cooling temperature: from 20-30 degrees C to 3-5 degrees C Control: PLC Unitronics V1040, Weber 2022 software Vacuum pump: 1 x Busch RA R5 0305D ( 300 m3 / h ) Chiller: Aermec ANL 202 Compressor: Metabo Basic 250-24W OF

Motor power: 565 kW AvK generator with 660 kVA, year of construction 2000 Diesel generator was used as an emergency generator, therefore only about 145 operating hours in test operation. Subject to prior sale - errors possible Internal reference number: E-1160

Rademaker / Rondo ‘salmon en croute’ line Rademaker block processor with Rondo make up line. Has been producing ‘Salmon en croute’ for major UK supermarkets. Whole line is in lovely condition and can obviously be easily adapted to run other products like pasties, sausage rolls etc. Mainly used seasonally so only 11,800 running hours.

Container generators with 2 CAT C32 units with 1000 kVA power each Generator: Stamford HCI634J2 Operating hours: Only 21 Cooling: Water Speed: 1500 rpm Voltage: 400/231 V, 50 Hz Tank: 4x 860 litres The generator was used in an emergency power system, the condition is excellent. The last test run took place in November 2022. Subject to prior sale - errors possible Internal reference number: E-1004-54

technical details generator: - Type: Synchronous - Rated voltage: 230 V - Apparent power at LTP: 4.18 kVA - Active power at LTP (emergency power): 3.8 kW - Apparent power at COP: 3.63 kVA - Active power at COP (continuous power): 3.3 kW - Protection class generator: IP 23 - Version sockets: 2 x 230 V, Schuko - Protection class sockets: IP 44 technical details drive: - Drive: SC170B - Power factor: 0.9 cosφ - Starter: Hand start - Engine oil quantity: 0.25 (min) - 0.6 (max) liters - Fuel: Gasoline - Tank volume: 15 liters - Runtime at 50% load: 14.0 hours - Runtime at 100% load: 9.5 hours - Sound pressure level Lp: 75 dB(A) - Sound power level Lw: 96 dB(A) Dimensions and weight: Length: approx. 595 mm Width/depth: approx. 460 mm Height: approx. 527 mm Weight: approx. 55 kg Scope of delivery: - 1 x wheelset with folding handle (Changes and errors regard ...

Proximity switch, proximity sensor, position switch -Type: SMT-10F -Cable length: 2.5 m -Weight: 0.025 kg

1. Qty. 1 Second-hand process tank Mfc.: Glencore Volume: 26 m³ Built: 1999 Dia.: 3.0 m Height: 3.85 m Stopped: 2018 Material: AVESTA 2205 (Super Duplex Steel) Asset: Zinc Asturine Capacity: 440,000 t/Year Useful Volume: 20 m³ Diameter: 3000 mm Overall Height: 3850 mm Design: Atmospheric Pressure Service Temperature: 35º C Stored Product: Return Acid Density: 1.24 kg/dm³ Welding According to API 650 X-Ray According to API 650 Empty Weight: 2355 kg Weight in Service 24.800 kg Construction Structural Element Thickness Material Roof 6 mm AVESTA 2205 Depth 6 mm AVESTA 2205 Ferrule 4 mm AVESTA 2205

Motor contactor, auxiliary contactor, contactor, semiconductor contactor, contactor, overvoltage protection switch -Manufacturer: Weidmüller, surge protection switch -Type: PU 1+1 C Class II -Number: 6 pieces available -Price: per piece -Dimensions: 90/35/H60 mm -Weight: 0.2 kg/piece

Rubber sealing profile, sealing plate, curing tool, seal, edge protection, solid rubber rectangular profile -Rubber sealing profile: with 2 grooves, 3 pieces -Length: 3 x 8450 mm / total 25.35 m -Cross-section: 50 x 55 mm -Groove width: 5 mm -Weight: 120 kg

Sound-insulated generator with Perkins diesel engine Power: 60 kVA Year: 2020 Operating hours: None Generator: Stamford / AvK S1L2Y1 Voltage: 400/231 V, 50 Hz Cooling: Water Tank: 175 litres Control panel: Manual and automatic operation with ComAp AMF9 generator circuit breaker, socket distribution Subject to prior sale - errors possible Internal reference number: E-1004-55

Postforming machine in cycle Brandt type PF 20/31 Specifications: • Working length max. (mm): 3100 • Profile height max. (mm): 200

proximity switch -Ø: 3.6 x 20.5 -stainless -Protection class: IP 67 -Number: 7 pieces -Price: complete -Weight: 70 g

Specifications: Shelving system: Feralco suitable for clear width: approx. 2,710 mm Projection: approx. 100 mm The scope of delivery includes: 01x push-through protection, used Material colour: RAL 2004 orange Total length: approx. 2,787 mm Profile dimensions: approx. 35 x 35 mm including 2 agraffes Weight: 7,16 kg | Pcs. Left|right L flat iron welded on, which are screwed to the shelf stand.

Inv. Num. : 6594 Type: VMX 42 SR Producer: Hurco Generated: 2008 Parameters: Control system: Winmax Work table length: 1270 mm Work table width: 610 mm Maximum table load (even): 500 kg Speed: 12000 1/min Travel X-axis: 1066 mm Travel Y-axis: 610 mm Travel Z-axis: 610 mm Cone: SK40 Machine weight: 7550 kg Equipment: C-axis: CNC rotary table B-axis 2016: new spindle

Control cabinet, distribution cabinet, control cabinet TS modular cabinet, profile door -Profile door KTS for: refrigerator -TS8 1200 x 2200 -Price: per piece -Number: 2 pieces -Dimensions: 2240/680/H280 mm -Weight: 66 kg

Control: Siemens Travel X/Y/Z: 350 x 240 x 340 mm Spindle speed 6300 min-1 Tool holder SK 40 Manual swivel rotary table Tool holder Vice Accessories

Tecnograf TECNO 100 Book Stacker Printing Print Stacker Stacking Currently in stock

Stainless steel container 1000 l Manufacturer: Willi Lermer Wiesbaden Volume 1000 l stackable 10 pcs available Very good condition, straight from production!

AUTOMATIC FEEDER FOR HERRING, SARDINE, BAADER 478 The usefull capacity of the BAADER 36 and 134 herring filleting machine can be increased by a combination with the BAADER 478 automatic feeder wich aligns herring, sprats, sardines and similar fish and feeds them to the processing machine. A variable-speed elevator raises the fish from a water filled hopper and delivers them uniformly to five feed channels. Fish traveling head forward are led directly to the timing device. Fish with tail leading are turned around. The timing device releases single fish synchronized wuth the processing machine and transports them through a back and belly aligning device into the feed troughs of the processing machine. It can be combined with Filleting machine for herring, sardine, Baader 134

HEADING MACHINE, BAADER 421 Technical description: Machine number: 10-4604-0421 Belt width: 300 mm Lift height: 1050 mm Estimated throughput: 35 fishes/min but varying in accordance with fish size and stillness of the operator Water consumption: 12 l/min Weight: 520 kg Dimensions: 2350 x 1600 x 1750 mm

CEPHALOPOD CUTTER WITH POSITIONING BAND, MECALSA TYPE: MC CTDP/CH200 Technical description: Material: Stainless steel Voltage: 380/440 V Frequency: 50/60 Hz Cutting pitch between blades: 40 mm

EEL GUTTING MACHINE, BAADER TYPE: 143 Technical description: Serial number: 10-3404-0143 Power supply: 220-380 V, 3 Ph, 50 Hz, 6.5 A, 2.5 kW Clearance: 125 x 110 mm Dimensions: 3000 x 1000 x 1250 mm The BAADER 143 guts eel from 130 to 1200 g, the gutting cut is performed in the usual way. The belly cavity is cleaned by scaper, a suction scoop and a rotating brush, the machine can be adjusted for 3 size ranges. Eel support troughs, scrapers and scoops for the different size ranges can easily be exchanged.

FILLETING MACHINE BAADER TPYE: 184 Technical description: Machine number: 10.3320 0184 Power supply: 380 V, 3 Ph, 50 Hz, 11.5 kW, 22.0 A Plastic conveyor belt width: 500 mm Band width: (2x) 160 mm Throughput: 24-40 pieces/min Water consumption: 25 l/min Weight: 2.500 kg Dimensions: 5400 x 1300 x 1450 mm This machine is laid out for filleting gutted and headed cod, haddock, saithe, hake, merluza and withing from 30 to 70 cm in total lenght (=0.3 to 2.5 kg, gutted including head). Proven BAADER filleting system providing for highest yield and reliability. The BAADER 184 is equipped with an integrated skinning device.

Motor protection relays, relays, heating current monitoring, preheating for generators, contactor, semiconductor contactor, contactor -Type: 3RN1011-1BB00 -Price: per piece -Number: 7x available -Weight: 130 g

Motor protection relays, relays, heating current monitoring, preheating for generators, contactor, semiconductor contactor, contactor -Type: 3RN1010-1BB00 -Price: per piece -Number: 12x available -Weight: 130 g

GUTTING MACHINE FOR HERRING, BALTIC HERRING, SARDINES, MACKEREL AND WHITEFISH ARENCO MODEL: CIS Technical description: Power supply: 380-440 V ? 50-60Hz Conveyor width: 260 mm Dimensions: 3600 x 900 x 1330 mm

TROUT GUTTING MACHINE BAADER, TIPO: 140 Technical description: Serial number: 74-9019-0140 Power supply: 380 V, 3 Ph, 50 Hz, 7 A Dimensions: 3050 x 550 x 1240 mm This machine is laid out for gutting trouts of a live weight from 240 to 650 g in a commercial manner. The abdominal cavity is cleanly cut open and the guts including the kidney are completely removed by means of a vacuum suction device. The special design of the BAADER 140 is capable of gutting up to 38 fish/min. The gills can either be removed or retained; this requires an easy adaption.