128,848 used machines on RESALE, but how to find them? Machine Search
SCM C30 4-fold combination machine Format Circular Saw Dressing Thickness Planer Machine Milling Machine Planing width 300mm Planing shaft: 3-tersa knife shaft Dressing table length: 1200mm Passage height: 3-200mm Format sliding table: 1070mm Besaeumlaenge Cutting height: 80mm Saw 90°-45° swivel Engine power: 400V 2 hp S1 Milling machine rigid 90° Milling machine rpm: Speeds of 4200-6300 rpm or 5000-7500 rpm G&STÜ-5500030 relkag21 SPECIAL PRICE: Fits in any small workshop!
Combined surge arrester module Blitzductor, Profibus single module, for PLC control, lamp holder -3x: 919670 -3x: 919562 -6x: 919506 Price: complete -Weight: 0.5 kg
Weibert WJ-CU-32 5-fold combi With format sliding table 2,60m Saw blade 250-315mm swivel: 90°-45° Planing width of 320mm 3 knife shaft reversible knives (no more adjustment) Passage height of 4-225mm Milling machine: 90°-45° swivel backwards Milling machine rpm: 3000/4000/5000/ 6000/8000 and 10000 rpm Height stroke 160mm Engine power: 3 motors 4KW 400V WY-500200 ILLUSTRATIONS WITH SPECIAL EQUIPMENT, IF APPLICABLE
\" Power: 125 kW (3.0 diesel); Euro N/C Operating parameters: Manual gearbox; mileage 413,000+ km; GVW truck 3.5 t; GCW (comb.) 10 t; ABS; cruise control Workpiece capacity: BE-combination 10 t; open trailer; dim. L 12,300 mm x W 2,550 mm x H 1,100 mm; full aluminium body; winch; 13–15 pin connector Supported edges: N/A Edge types: N/A Included equipment: A/C (Klima); Webasto heater; air seat; ABS (truck + trailer); new tyres (6x truck + 4x trailer); rear brakes replaced; compressor hose new; turbo new; EGR cooler new; complete timing chain kit; prop shaft bearings + joints; all oils + antifreeze new; trailer: new air bags, valves, wheel bearings, full new lights + wiring Compliance: BE driving licence combination; road registered vehicle Power supply: Diesel Year/Manufacturer: 2012 / Iveco Daily 40C17; trailer 2007; aluminium construction Remarks: High mileage; exten ...
Weibert CU-41 Combine With format sliding table 2,60m Saw blade 250-315mm swivel: 90°-45° Planing width of 410mm 4 knife shaft reversible knives (no more adjustment) Dressing table length of 1800mm Passage height of 4-225mm Milling machine: 90°-45° swivel backwards Milling machine rpm: 3000/4000/5000/ 6000/8000 and 10000 rpm Height stroke 160mm Motor power: 3 motors 4 KW 400 V WY-500300 ILLUSTRATIONS WITH SPECIAL EQUIPMENT, IF APPLICABLE
Battery test result 100% Auction-ID: A1-40975-2
Weibert W7-41 Station wagon Planing width : 410mm Motor power: 3 motors 400V 2.2 KW Dressing table length: 1500mm Planing shaft: 3-reversible knife shaft Passage of 4-230mm Format sliding table 1500mm Cutting height: 103mm Saw blade 315mm swivel 90°-45° Milling machine: rigid 90° Milling machine rpm:1400/3500/6000 and 8000 rpm WY-500400 Illustration similar!
Loma Combination IQ3 metal detector and CW3 check weigher 250 x 90mm aperture. 200mm conveyor width. 360mm weigh pad width. 2100mm machine length. 920mm line height with adjustable feet. M&S Spec machine.
Auction-ID: A7-45419-64
On and including pallet in good working condition Auction-ID: A1-40103-104
Diesel combined heat and power plant, CHP, generator set, power generator used A. van Kaick Year: 1991 Generator DKBN49/200-4 200 kVA 400/231 V 289 A 50 Hz Mtu 8V183TA32 MERCEDES OM 442A 240 kW 1500 rpm Tank dimensions approx. 3600 x 1500 x 1500 mm Dimensions container: approx. Mm Changes and errors in the technical data, information and prices as well as prior sale reserved.
Sliding Table Saw Milling Machine Planing Machine Slotted Hole Drilling Machine Combination Machine Table Saw Circular Saw Carpenter Circular Saw Format Saw Panel Saw Table Milling Machine Swivel Spindle Milling Machine FIELDS Type: BF6-31 YOC 1990 Format sliding carriage 1.6 cm Manual height adjustment of the saw blade Manual swivel of the saw blade up to 45° Rip fence with fine adjustment up to approx. 80 cm Boom table Miter stop Motor power main motor 3 KW Swivel spindle milling machine Manual height adjustment of the swivel spindle Manual swivel of the milling spindle up to 45° backwards. Milling spindle diameter 30 mm 3 speeds adjustable via belt. Milling spindle under table retractable and removable. Engine power milling unit 3 KW Milling fence with fine adjustment Dressing thickness planing machine Planing width 31 ...
Diesel combined heat and power plant, CHP, generator set, power generator used DIETER KUNZLER GmbH Generator K-EA-3ST-PAR-SYN-M 500 kVA 400/231 V Synchronous 3x 362 A 50 Hz Mtu 12 V 183 AA 31 MERCEDES OM 424 225 kW 1500 rpm Dimensions unit: approx. 2500 x 1200 x 1500 mm, control cabinet approx. 2400 x 500 x 2000 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.
Diesel combined heat and power plant, CHP, generator set, power generator used DIETER KUNZLER GmbH Year: 1991 Generator 250DMED 250 kVA 400/231 V 3x 362 A 50 Hz Mtu 12 V 183 AA 31 MERCEDES OM 424 225 kW 1500 rpm Container dimensions: approx. 6000 x 2500 x 2500 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.
RATIONAL Combi Master Plus convection oven, untested!, uncleaned with shelf Auction-ID: A7-45677-1
Belt width 150 mm Strap length 1220 mm Grinding wheel dimension 225 mm Work table: 150 x 400 mm Table adjustable up to 90 degrees Table surface 150 x 130 mm Connection voltage 230 V Total power requirement 0.75 kW Machine weight approx. 35 kg Space requirement approx. 650 x 360 x 400 mm Condition: never used / new (5)
Combi steamer 20 x 1/1 GN, 400 V, Eloma Multimax B20-11, 400 V, 45 kW, 60A, Fixed connection, Steaming, Combi steaming, Hot air, NT cooking, Core temperature, Manual steaming, Clima active, Energy saving, Reduced fan speed, Autoclean, Water shower, Dimensions 103x88x193 cm, Refurbished with warranty6300
Standard Configuration ? Stable C-frame ? Coordinate guide with integrated linear magazine, 19 tool stations,2 clamps ? Drives: Maintenance-free, three-phase servo motors ? Programmable presser foot for repositioning with preselectable pressing force ? Sensor-monitored part chutes 500 x 500 mm for punching and laser station, ejection cylinder on the laser chute ? 2 good parts containers ? Laser unit: CO2 laser TLF2700, radio-frequency excited, insulated against vibrations, integrated in machine frame, incl. chiller, and laser control DIAS 3 ? High speed processing with SprintLas ? ContourLas for producing small holes ? Programmable cutting gas pressure setting ? Punch stroke / thread counter ? Laser cutting head: 5? lens, quick-change device, height regulation APC ? Additional laser cutting head with 7.5? lens ? Punching head: Hydraulic single tool adapter, 360? rotation of all tools, ...
Belt width 100 mm Strap length 915 mm Grinding wheel dimension 200 mm Work table: 170x125 / 265x15 mm Total power requirement 0.5 kW Machine weight approx. 26 kg Space requirement approx. 0.6 x 0.5 x 0.3 m Condition: never used / new (5)
Standard configuration Machine ? Stable C-frame for easy access ? Coordinate guide for high-precision machining ? Linear magazine, 21 tool stations, 3 clamps ? Drives with maintenance free 3-phase servo motors ? Repositioning unit with programmable stripper ? Ball tables ? Sensor-monitored parts chutes 500 x 500 mm for punching and laser station, ejection cylinder on the laser chute ? 2 Good parts containers ? AutoLas TRUMPF Laser ? Laser unit: TruFlow 2700 CO2-Laser ? Radio-frequency excitation ? Chiller unit ? Laser control: TASC 3 ? Encapsulated beam delivery Cutting head ? Cutting head with 5.0 and cutting head with 7.5 lens focal length ? Cutting head quick-change device ? Programmable cutting gas pressure ? DIAS ? ContourLas Punching head ? Hydraulic punching head, 360? rotation for all tools ? Programmable presser foot for repositioning ? Tool length compensation ? Vacuum slu ...
CHP basic module agenitor 212 (fully mounted on steel frame with vibration decoupling) - Motor with accessories - Gas controlled system - Gas mixer -Generator -Voltage regulator - Cos-phi regulator -Clutch - Switchgear and control system - Exhaust silencer made of stainless steel CHP power field - Separate control cabinet with load switch and mains monitoring Heat exchanger cabinet, pre-piped mounted in steel frame - Heat extraction / hydraulic system - 3-way mixer emergency cooling circuit - electric circulating pump, mixture cooler - 3-way mixer mixture cooling circuit - Pressure compensation tank - Plate heat exchanger as transfer heat exchanger - electric circulating pump heating side - 3-way mixer return temperature increase Mixture cooler as table cooler Emergency cooler as table cooler to dissipate excess thermal energy. The entire thermal energy fro ...
- Pallet feeder FP 95 incl. VACULIFT III - MC Control - 1. Station 4 Niro fold buckles - Perforating, creasing and cutting deivce parallel fold - KL- und SUPER KTL-Version with 2 knifes - Vertical Stacker SBAP 46-ME, Bj. 2016 - Stream delivery ASP 66-2ME, Bj.2012
CHP basic module agenitor 206 / 220kw/el. (fully mounted on steel frame with vibration decoupling) - Motor with accessories - Gas controlled system - Gas mixer -Generator -Voltage regulator - Cos-phi regulator -Clutch - Switchgear and control system - Exhaust silencer made of stainless steel CHP power field - Separate control cabinet with load switch and mains monitoring Heat exchanger cabinet, pre-piped mounted in steel frame - Heat extraction / hydraulic system - 3-way mixer emergency cooling circuit - electric circulating pump, mixture cooler - 3-way mixer mixture cooling circuit - Pressure compensation tank - Plate heat exchanger as transfer heat exchanger - electric circulating pump heating side - 3-way mixer return temperature increase Mixture cooler as table cooler Emergency cooler as table cooler to dissipate excess thermal energy. The entire thermal ...
We offer for sale a Cummins gas CHP 2000 KW. Specifications Engine: Cummins Type: D67 Power: 2000 KW Year of construction: 2007 Revolution: 1500 1/min Generator: Stamford Power: 2650 KVA Voltage: 380 V Frequency: 50 Hz Operating hours: 59,000 h
Weibert W7-32 5-fold station wagon Planer width: 320mm Cutting length 1700mm Milling stop for tool max. D=220mm 3 motors 3kW Price 5967,-€ excl. VAT Price 7100,-€ incl. VAT
- The Haas TR 160 rotary gives a Haas machine tool the ability for multi-sided machining. - Disc diameter: 160mm - Maximum load: 49 kg - Excluding control unit
Stone and belt grinding machine Motor power 900 watts. Speed 2950 rpm. Dimensions whetstone 200 x 32 x 30mm. Dimensions sanding belt 100 x 915 mm. Package sizes 62 x 54 x 30 cm. Weight 35 kg. Condition: never used / new (5)
Belt and disc grinding machine Belt width 25 mm Strap length 762 mm Grinding wheel dimension 125 mm Table adjustable up to 45 degrees Table surface 130 x 130 mm Connection voltage 230 V Total power requirement 0.3 kW Condition: never used / new (5)
Belt grinding station, support table with T-slot, Sanding belt width 100 mm, Sanding disc D 300 mm, with support table 350 x 140 mm, Suction connection available. Motor power: 0.9/ 1.3 kW 400 V/ 50 Hz 1450/ 2900 rpm Connection cable with CEE plug 16 A Machine dimensions: H 1450 x D 410 x W 900 mm Weight approx. 200 kg Transport vertical, bolted to EURO pallet.
machine ready for transport and to be assessed on viewing day
Weibert HX 260-CE 5-fold station wagon Motor 3x 3HP, 400V, 50Hz Saw blade diameter 250mm Cutting height 85mm to 90° Cutting height 55mm to 45° Milling mandrel 3000/6000 rpm Sliding table 1450 x 320mm Cutting length 1200mm Mitre stop Eccentric clamp Weight: 485kg G&RO-HX260-CE
Weibert W7-32 Profi 5-fold station wagon Planer width: 320mm Cutting length 2100mm Milling stop for tool max. D=220mm 3 motors 3kW Price 6975,-€ excl. VAT Price 8300,-€ with VAT.
Weibert W7-32 Top 5-fold station wagon Planer width: 320mm Cutting length 2600mm Milling stop for tool max. D=220mm 3 motors 3kW Price 7984,-€ excl. VAT Price 9500,-€ with VAT.
Key data: 537 , 400
Pro2 container unit with 537kW el. Performance as a pure power generator incl. heat recovery system - 40 ft normal container (L x W x H in metres) 12.2 x 2.55 x 2.55 metres with lighting - MWM genset TCG2016V12 - 537kW for landfill gas, biogas or natural gas with gas control system and control cabinets for plant control, auxiliary drive supply and GLF - Current operation hours about 87,000 - Soundproofed design as a plant container - Separation of containers into engine room / electrical room with connecting door - Access door to the engine room on the longitudinal side and electrical room on the front side - Gas detector and smoke detector - Supply and exhaust air system with backdrop silencer and supply air filtration - Engine cooling water circuit with circulation pump, warm-up control via 3-way mixer - Emergency cooling for HT circuit integrated into the engine cooling wat ...
Weibert W7-32 5-fold combi woodworking machine New machine (immediately available) Planer width: 320mm Cutting length 1700mm Milling stop for tool max. D=180mm 3 motors 3kW Digital display milling machine Price: kpl. 5874,-€ excl. VAT 6990,-€ incl. VAT
Pro2 container unit with 311kW el. Performance as a pure power generator - 40 ft normal container (L x W x H in metres) 12.2 x 2.55 x 2.55 metres with lighting - MWM genset TBG 616V8K - 311kW for landfill gas, biogas or natural gas with gas control system and control cabinets for plant control, auxiliary drive supply and GLF - Current operation hours only about 95,000 - Soundproofed design as a plant container - Separation of containers into engine room / electrical room with connecting door - Access door to the engine room on the longitudinal side and electrical room on the front side - Gas detector and smoke detector - Supply and exhaust air system with silencer and supply air filtration - Engine cooling water circuit with circulation pump, warm-up control via 3-way mixer - Emergency cooling for HT circuit integrated into the engine cooling water circuit, designed for the co ...
Combined heat and power plant with generator El. Power: 40 KW Thermal power 72 KW Fuel: natural gas Mains connection 400 V 50 Hz 100 A Flow 90 C Return 70 C Pressure 16 bar Generator 60 KVA Length 2.40 m Width 1 m Height 1.60 m
Siemens combined X-ray recording and fluoroscopy device Iconos R 200 with the following system components: Generator Polydoros SX 65 Tube Optitop 150/40/80 HC 0,6/1,0 Digital image processing Fluorospot Compact Sirecon 33-4 HDR image intensifier • Before taking over, all devices and systems have been tested on site for their functionality. • The system is located in our warehouse in Freiberg / Germany. It is packed on pallets, professionally lashed and wrapped with stretch film and can be picked up immediately • You buy the system in the "AS" condition from the warehouse Freiberg (EXW), Saxony, Germany, and pay in advance. • Sold as "Used", EXW Freiberg, Saxony, Germany, to resellers or dealers despite full functionality without warranty. • The installation, commissioning and configuration of the system or system components must be carried out by the manufactur ...
Combination with the Intermac CNC Crease Grinder Groove 1500 (no. 23020) - Serial Number: 90147 Weight: 200 kg Power: 0,8 Kw + internal extraction Length mm: 900 Width mm: 1000 Height mm: 1700 Working height: 1200 Transport size L x W x H: 0,9 x 1,0 x 1,7 Number of spindles: 1 spindle Condition machine : Good Control type: Manually Electric. Connection: 16A 3P+N+PE - For more information, please mail us: salestecfort.nl
Weibert FR3 Sliding table saw milling machine NEW MACHINE Motor: 400V 4kW 2 motors Format sliding table: 2300mm Cutting height: 103mm Swivel saw blade, max. 315mm Milling machine rigid 90° Milling machine 1500/3500/6000/8000 rpm complete with boom WJ-400100
Transnorm modular conveyor with combiner conveyor belt GF 2500-1300-1200 RA2230 Merging of two belts into one Technical data: Conveyor length (NL): 2500 mm Frame width (NB): 1300 mm, 1600 mm with motor Belt width (GuB): 1200 mm Overall height (BH): 80 mm, 430 mm with motor at the bottom, approx. 1000 mm with motor at the top Scraper height: 190 mm (without motor) Belt width/height scraper: 180 mm Support feet: optionally available Conveyor speed (v m/s): 1 Drive: SEW geared motor, R17 DT80N4 Electrical data: 50Hz V380-500, kW 0.75 S1 Drive pulley: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Lateral guide on one and both sides Frequency inverter for stepless speed change Adjustable length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2001 condition: good (used) Conveying length ...
Engine type: 18V34SG Electrical power output: 5500kWe, 6838kVA Engine speed, direction: 750rpm, CW Generator type: ABB HSG 900XS8, 15kV, 50Hz Engine control system: WECS 3000 Turbocharger: Napier NA 355 Fuel: Natural gas Application mode: Cogeneration power plant Year: 1995 Running hours: 54855 h Running hours since last overhaul (48721rhs, 05.2010) 6131 h Next major overhaul: 64000 h Original installation: Denmark Genset condition: Excellent Stopped: 08.2022 Service history and documentation: Available Location: Denmark (will be in Hungary 2024 Q2) Scope of supply: Genset Heat recovery Gasramp Silencer lube oil tank Starting air compressor and vessel
Tersa Knife Shaft Motor 3x 3HP, 400V, 50Hz Saw blade diameter 250mm Cutting height 85mm to 90° Cutting height 55mm to 45° Mandrel 3000/6000 rpm Sliding table 1450 x 320mm Cutting length 1200mm Mitre fence Eccentric clamps Weight 485kg G&RO-HX260-CE
maximum number of results exceeded
please refine your search
9.000 € 
