We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
120,454 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
Beer combi filter 25 HL /h More then 300 machines new and second hand on our seema .de
used
Siemens combined X-ray recording and fluoroscopy device Iconos R 200 with the following system components: Generator Polydoros SX 65 Tube Optitop 150/40/80 HC 0,6/1,0 Digital image processing Fluorospot Compact Sirecon 33-4 HDR image intensifier • Before taking over, all devices and systems have been tested on site for their functionality. • The system is located in our warehouse in Freiberg / Germany. It is packed on pallets, professionally lashed and wrapped with stretch film and can be picked up immediately • You buy the system in the "AS" condition from the warehouse Freiberg (EXW), Saxony, Germany, and pay in advance. • Sold as "Used", EXW Freiberg, Saxony, Germany, to resellers or dealers despite full functionality without warranty. • The installation, commissioning and configuration of the system or system components must be carried out by the manufactur ...
used
MACHINE WAS ORDERED BARND NEW FROM THE 1. ST OWNER MACHINE IS STILL ON POWER WORKING DAYLY ORDERS LASER POWER : 2000 W MAX SHEET THICKNESS: 4 mm MAX PUNCHING FORCE: 165 kN ATTACHED VIDEO FOR CUSTOMER WE CAN ORGANIZE DISMANTLING, TRANSPORT
new
Weibert HX 260-CE 4-fold combi Tersa Knife Shaft Motor 3x 3HP, 400V, 50Hz Saw blade diameter 250mm Cutting height 85mm to 90° Cutting height 55mm to 45° Mandrel 3000/6000 rpm Sliding table 1450 x 320mm Cutting length 1200mm Mitre fence Eccentric clamps Weight 485kg G&RO-HX260-CE
used
Combined Cycle Gas Turbine Power Plant 75 MW/50 Hz – Zero Hours This equipment was delivered in 2017 by an EPC contractor who selected Rolls-Royce and Siemens as main equipment suppliers. This was a greenfield project and therefore delivery contained all equipment needed for 75 MW power plant operation, like fuel gas treatment plant, water treatment plant and complete switchyard with step-up transformers Manufacturing year: 2017 Gas turbine: Rolls-Royce Trent 60, Dry Low Nox Steam turbine: Siemens SST-300 Step up tranfomers: 2 pc Alstrom 11kV to 154 kW Complete switchyard: Siemens 154 kV Nominal output 100%: 60 MW + 15 MW Max efficiency: Single cycle 42 %, combi cycle 54% Heat recovery steam boiler: 30 bar / 300 C Water treatment: Sand and active coal filters + RO Documentation: Complete original in English Delivery: Complete plant equipment from water and gas t ...
new
Weibert FR3 Sliding table saw milling machine NEW MACHINE Motor: 400V 4kW 2 motors Format sliding table: 2300mm Cutting height: 103mm Swivel saw blade, max. 315mm Milling machine rigid 90° Milling machine 1500/3500/6000/8000 rpm complete with boom WJ-400100
new
SCM lab 300p 5-fold combi Universal Multiple Combination Aluminium sliding slide 3 Tersa planer knife shaft Trimming length 1600mm max. saw blade diameter 315mm with scoring Swivel saw blade Dressing width 300mm Dressing table length 1300mm Thickness table dimension 300 x 450mm min./max. thickness height: 3/220mm Motor 50Hz 4kW 400V max. milling tool diameter 160mm Spindle speed: 3600/7500/10,000 rpm Spindle diameter: 30mm Weight 430kg G&STÜ-5500314
new
Weibert HX TZ Saw-milling machine Motor: 2x 4 HP, 400V, 50hz Saw blade diameter 250mm Cutting height 85mm to 90° Cutting height 55mm to 45° Sliding table 1450 x 320mm Cutting length 1200mm Cutting width between saw blade and rip fence 600mm Mitre fence with eccentric clamp Weight 340kg G&RO-HX-TZ
used
Key data: 600
MWM TCG 2016V12 600 kW el. power, 50 Hz after main overhaul with, also prepare TC, Intercooler, alternator) genset. Fully completed - also possible option add: control panel, power switch automat, container, cooling an heat system.
used
Dough sheeter and sheeter, combination sheeter, sheeter -Roll width: approx. 600 mm -Unrolling thickness: from 0.3 - 30 mm -with round and long moulder type: SR0 -Meal container -16 A-CEE plug -Connection: 380 V, 0.75 kW -Sheeter is mobile -Dimensions: 1900/1250/H1900 mm -Weight: 430 kg
used
Profile steel shears, profile shears, punch, punching machine, hole punch, hydraulic flat/profile and bar steel shears -Manufacturer: Peddinghaus, profile steel scissors 5-way combined model 210 SUPER 11 -Pressure force: 40 tons -Drive power: 3/2.2 kW 2800/1400 rpm -Applications: punching, shearing, cutting, notching -Footswitch: 2 -Length stop: Electric contact stop, adjustable up to approx. 1 m -Accessories: incl. various. Stamps and dies see photos -Dimensions: 1620/1350/H1740 mm -Weight: 1323 kg
used
Profile steel shears, profile shears, punch, punching machine, hole punch, hydraulic flat/profile and bar steel shears -Manufacturer: Peddinghaus, profile steel scissors 5-fold combined model 210/13 on a rotating machine base -Pressure force: 70 tons -Drive power: 4/5 kW 1450/2900 rpm -Throat: 610 mm -Applications: punching, shearing, cutting, notching -Accessories: incl. various. Stamps and dies see photos -Dimensions: 1865/1205/H1990 mm -Weight: 3580 kg
used
Combined copying milling machine - lathe MICHAeL KAeMPF -Online-Video-Inspection by Skype-Video- -We would be very pleased with your visit - more machines on Stock- -Available Immediately - Can be inspect- -On Stock Emskirchen / Nuernberg - Can be test-
used
Kombi-Falzmaschine - Combination Folder Heidelberg-Stahlfolder KH82-4KTL Year 2010 - Serial-No. FH.ERCA-00434 Palettenanleger / Pallet Feeder PFH-82 Format / Size min. 140 x 180mm Format / Size max. 820 x 1200mm Falztyp / Folding Type: 4 buckles - 2 knives - 1 side buckle Automatische Falztascheneinstellung / automatic buckles setting Speed 50.000 Cycles/hour Digitaler bildschirm / Digital Display Inklusive Kompressor / include Compressor Inklusive Handbuecher / Included Manuals Auslage / Delivery Palamides Alpha 500 Plus Year 2011 - Serial-No. 2502 Arbeitsbreite max. 510mm / Working width max. 510mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nuernberg - Can be test
used
Kombi-Falzmaschine - Combination Folder Heidelberg-Stahlfolder KH78-4KTLL Year 2006 - Serial-No. FH.FNJ0-00256 Palettenanleger / Pallet Feeder PFH-82 Format / Size min. 140 x 180mm Format / Size max. 780 x 1280mm Falztyp / Folding Type: 4 buckles - 3 knives Automatische Falztascheneinstellung / automatic buckles setting Speed 50.000 Cycles/hour Digitaler Bildschirm / Digital Display Auslage / Delivery Heidelberg SAK-94.H Inklusive Kompressor / include Compressor Inklusive Handbuecher / Included Manuals Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nuernberg - Can be test
used
Transnorm modular conveyor with combiner conveyor belt GF 2500-1300-1200 RA2230 Merging of two belts into one Technical data: Conveyor length (NL): 2500 mm Frame width (NB): 1300 mm, 1600 mm with motor Belt width (GuB): 1200 mm Overall height (BH): 80 mm, 430 mm with motor at the bottom, approx. 1000 mm with motor at the top Scraper height: 190 mm (without motor) Belt width/height scraper: 180 mm Support feet: optionally available Conveyor speed (v m/s): 1 Drive: SEW geared motor, R17 DT80N4 Electrical data: 50Hz V380-500, kW 0.75 S1 Drive pulley: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Lateral guide on one and both sides Frequency inverter for stepless speed change Adjustable length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2001 condition: good (used) Conveying length ...
used
Transnorm roller curve combination right and left 45°-1200-900-800 IR800 1551 mm RA2232 Make: Transnorm Running direction: Curve combination clockwise/anticlockwise Roller width (RB): 800 mm conical, plastic coating Nominal/outer width (NB): 900 mm Inner radius (IR): 800 mm Center section length: 1200 mm Offset: 1551 mm Frame height: 80 mm Overall height including motor: 450 mm Drive/transmission: Chain Electrical data: 300-500 V, 0.37 kW Gear motor: SEW, R17DT71D4/TH Conveying speed: please contact us Scope of delivery: without supports Optionally available: Supports Lateral guide on one and both sides Frequency inverter for stepless speed change Length adjustment (longer/shorter) Other roller conveyors/roller curves with chain transmission Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2008 condition: good (used) Nomina ...
used
Engine type: 18V34SG Electrical power output: 5500kWe, 6838kVA Engine speed, direction: 750rpm, CW Generator type: ABB HSG 900XS8, 15kV, 50Hz Engine control system: WECS 3000 Turbocharger: Napier NA 355 Fuel: Natural gas Application mode: Cogeneration power plant Year: 1995 Running hours: 54855 h Running hours since last overhaul (48721rhs, 05.2010) 6131 h Next major overhaul: 64000 h Original installation: Denmark Genset condition: Excellent Stopped: 08.2022 Service history and documentation: Available Location: Denmark (will be in Hungary 2024 Q2) Scope of supply: Genset Heat recovery Gasramp Silencer lube oil tank Starting air compressor and vessel
used
This combi steamer from the manufacturer Rational is a CombiMaster® Plus with 20 x 2/1 Gastronorm inserts in electric design. The combi steamer is the XXL version and offers space for 20x 2/1GN or 40x 1/1GN The device has been tested in our in-house workshop and is fully functional. Availability from week 8 The RRP. for this combi steamer is € 27,110 net. The price quoted is net plus 19% VAT. Service: We would be happy to put you in touch with a certified Rational customer service throughout Germany Are you looking for a specific type of Rational device? Ask us, we have access to an extensive range of used and new goods. We will be happy to advise you on all types of devices, whether SCC, CM, CMP, VCC, iVario, iCombi Classic and Pro. This device is the optimal choice if you are looking for a classic combi steamer that you want to operate manually. Our used equipment se ...
new
Tersa Knife Shaft Motor 3x 3HP, 400V, 50Hz Saw blade diameter 250mm Cutting height 85mm to 90° Cutting height 55mm to 45° Mandrel 3000/6000 rpm Sliding table 1450 x 320mm Cutting length 1200mm Mitre fence Eccentric clamps Weight 485kg G&RO-HX260-CE
used
Kombi-Falzmaschine - Combination Folder Heidelberg Stahlfolder KH82-4KTLL 32 Seiten Seitenfalz - 32 pages cross Fold Year 2008 - Serial-No. FH.FNJ0-00256 Palettenanleger / Pallet Feeder PFH-82 Format / Size min. 140 x 180mm Format / Size max. 820 x 1200mm Falztyp / Folding Type: 4 buckles - 3 knives Automatische Falztascheneinstellung / automatic buckles setting Speed 50.000 Cycles/hour Digitaler bildschirm / Digital Display Inklusive Kompressor / include Compressor Inklusive Handbuecher / Included Manuals Auslage / Delivery Heidelberg SAK-94 Year 2006 - Serial-No. FH.DAD0-00421 Arbeitsbreite max. 940mm / Working width max. 940mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nuernberg - Can be test
used
Key data: 1558 KW, 2300 kVA, 400 V
Engine Make: MWM Engine type: TCG 2020 V16 Power: 1558 kW RPM: 1500 Fuel: Natural gas Hz: 50 Year of manufacture: 2007 Operating hours: 57,000 h Scope of delivery: Motor+generator on base frame, motor control TEM, throttle line, pumps.
used
Kaeser FFG-48D Connections: 1" female thread already with compression fittings Compressed air filter combination Composed of: - FF-48D Compressed Air Microfilter 0.001ppm - FG-48 Activated Carbon Filter - ECO Drain 31 steam trap Last Kaeser service: 09/2021 Taken out of service since 03/2023
used
combined bending machine-straightening press, profile bending machine, bending machine, flat iron bender, horizontal bending/straightening press, horizontal bending machine -Flat iron bender: hydraulic profile bending machine -Pressure capacity: 140 Ton. -Stroke cylinder: 455 mm -Counter bearing max width: 1250 mm -Support rollers: height adjustable 250 mm -Dimension: 2060/3735/H1620 mm -Weight: 8300kg
used
Key data: 130 , 200
MAN gas generator enclosed in sound proof chamber, in good condition. It has the following specifications: Manufacturer: MAN Fuel: Gas Manufacture year: 2010 Kva: 200 Power: 130 kW Other specs: Turbo included. Control panel included.
used
Natural gas CHP MAN E2876 E312 Power el.: 143 kW Power th.: 205 kW 6 cylinders Commissioning: 2017 Hours: 44650 Full maintenance by AVS Aggregate has been preserved Generator: Manufacturer: FKI - Type: MJB250LB/4 - 158/188 kVA Soundproofing hood 2x heat exchanger and heat accumulator 2x 5000 liters Subject to prior sale - errors possible Internal Reference Number: E-1175
used
PADE Trimming-Milling-Drilling Machine Model 1000/N: - Self-sliding worktop - Header blade D=400mm, 3 hp motor - milling machine with shaft D=30mm, motor hp 5 - 5-spindle drilling machine, 360° swivel, 3 hp motor Machine not according to CE standards, for export
used
4-jaw combination chuck, four-jaw chuck with individually and centrally adjustable jaws WMW, NILES DHK 315 x 4 ( DHK315x4 ) TGL 30-2333 < br />outer Ø: 315 mm centering Ø: 265 mm bolt circle Ø (chuck) : 290 mm bore Ø: 95 mm height with jaws: 160 mm including 2x chuck wrench jaws individually adjustable and rotatable used, tested ! dimensions ( lathe chuck ): 315 x 315 x 160 mm
used
Combined profiled steel shears and hole punch GEKA type HYD 80 / Hydracrop 80/A Masch. No. 9566 Year of manufacture approx. 2000 Punching force 80 ton. Projection 300 mm Punching up to 40 mm in 14 mm sheet metal Flat material shears 450 x 15 mm Angle steel shears 130 x 130 x 13 mm 4-point shears 45 x 45 mm Round material shears 45 mm Rectangular notchers up to 12 mm Motor power 5.5 kW Mains connection 400 Volt, 50 Hz stop with el. Lifting release 500 mm - Work table with stop for the hole device 550 x 380 mm - Working height of the hole device 1100 mm - Work table with stop for the rectangular notcher 550 x 400 mm - Working height rectangular notcher 930 mm - Approx. 21 pieces of various punching tools - Operating instructions - Original painting, not repainted Space requirement L x W x H 1800 x 1150 x 1950 mm Weight 1.7 ton. very good condition; used
used
Extra Accessories: SheetMaster Sheet Metal Supplier The machine is also working at the moment Make: Trumpf Type: Trumatic 6000L Year of construction: 2006 Hours: 90,119 Travel – x – 3085 mm Travel – y – 1550 mm Travel – x (combined) – 2500 mm Cutting capacity for mild steel – 8 mm Cutting capacity for stainless steel – 6 mm Cutting capacity for aluminium – 4 mm Workpiece – 230kg Punching force - 180 KN Punching speed – 917 1/min Watt laser power: 2700 Dimensions (LxWxH): 8400x8500x2200 mm
used
Doosan gas generator in good condition. It has the following specifications: Manufacturer: Doosan Fuel: Gas Manufacture year: 2008 Kva: 600 Mass: 3740 Other specs: 10 cylinder, electric panel, complete.
used
Scania Schnell Engine in good condition with the following specifications: Power: 250kW Mfy: 2006 Fuel: Gas /Diesel (Dual fuel) Voltage: 400V
used
dia. range 4 - 15 mm cutting length 2000 - 4000 mm speed - meters/min 15/30
used
This Trumpf Trumatic 600L laser punch combination machine was manufactured in 1998 in Germany. It is equipped with a Trumpf control unit. The machine has a laser power of 2. 4 kW and a punching force of 220 kN.
used
Description: Planer shaft motor Kw (Hp) 4 (5.5) Planer shaft with 4 knives Ø 110 mm Planer shaft rotation speed 5000 rpm Dust extraction port Ø 120 mm Flush worktable dimensions 2130×515 mm Thicknessing table size 960×515 mm Working height 4 - 225 mm 2 feed speeds 9 - 14 m/min Approx. Onsite Dimension. (l x w x h): 215 x 1,100 x 1,250 mm, weight approx.: 820 kg
used
Description: Planer shaft motor Kw (Hp) 4 (5.5) Planer shaft with 4 knives Ø 110 mm Planer shaft rotation speed 5000 rpm Dust extraction port Ø 120 mm Flush worktable dimensions 2040×410 mm Thicknessing table size 960×410 mm Working height 4 - 225 mm 2 feed speeds 8 - 14 m/min Approx. Onsite Dimension. (l x w x h): 2,100 x 1,000 x 1,250 mm, weight approx.: 690 kg
used
Overview The Dimac Star One P30 Tray/Shrink Packer was used in a Croatian brewery. As the bottling project is finished, the packer is for sale now. Last use was in December 2023 Tech. Details Capacity: 30 cycles per minute 0,5l – 2,0l bottles PET/Glass/Cans Can work with Pad Can work with transparent or printed film Formats: 3 x 2 and 4 x 3
used
Stove combination GORENJE, hob BR6AC-C1, mod. ECD643BX, item no. 730779/01, S/N 33430827, Built-in oven BCS6737E06BG
used
Gremser Flat Pile Feeder 4 fold pockets 1 sword fold Noise protection hood Machines Control and Counters Tape delivery
used
Description: Type of edging Thin edge Thick edge Gluing System PUR Combination Squaring Edgebanding Machine First Pass Max Panel Width 3000 mm Max feed speed 40 m/min Operating Units Right Side 10 nr Operating Units Left Side 10 nr Min. panel height 8 mm Max. panel height 60 mm Min. panel width 240 mm Max. panel width 3000 mm Min. edge thickness 0.4 mm Max. edge thickness 3.5 mm Max. forward feed speed 40 m/min Top pressure yes Pressure with rubber belt Panel support guides yes No. Panel Sizing / Milling units Left Side 1 NO. PANEL SIZING / MILLING UNITS LEFT SIDE 1 Unit : double chipper, top and bottom Constructor model : KD 11 motor power : 4.5 KW r.p.m. : 6000 RPM Same technical characteristics on the left side yes Edge coil magazine yes no. positions 12 Gluing system yes glue pot for PUR glue yes premelter for PUR glue yes Roller set to press the edge yes No. Edge Processing Units 8 ...
used
Description: Machine number: WFL 2248382 + WFL 2250409 max. pressure: 16 bar Delivery flow rate: 8,700 l/min Air connection: 1 1/2' , Approx. Onsite Dimension. (l x w x h): 350 x 150 x 620 mm, weight approx.: 12 kg
used
Description: Air flow rate: 18,000 l/min Machine number: WFL 2200504 + WFL 2292710 Max. pressure: 16 bar Air connection: 2 2/1' Approx. Onsite Dimension. (l x w x h): 450 x 170 x 780 mm, weight approx.: 22 kg
used
Key data: 790 KW, 738 kVA, 400 V
Deutz / MWM Gas CHP (Container) TBG 620 V12 Landfill gas generator from 1999 with 150,200 operating hours, E40 12/22, complete (container) with cooling. 1 available, 738 KWel x 1,500 rpm, 400 V/50 Hz. AC generator: Stamford HC I634K2-CG, 1,100 KVA Gas engine Deutz / MWM TBG 620 V12 Manufacturer: Deutz / MWM Model: TBG 620 V12 Type: Gas Engine (Landfill Gas) Serial Number: 2200633 Power [KW]: 790 Year of construction: 1999 Hours: 150,200, E40 12/22 Weight motor and generator [kg]: 7.800 Dimensions LxWxH [cm]: – AC Generator Stamford HC I634K2-CG Manufacturer: Stamford Model No.: HC I634K2-CG Type: AC Synchronous Generator Serial number: 0103530/01 Power [KVA]: 1,100 Voltage [V]: 400 Frequency [Hz]: 50 Electricity [A]: 1602 Speed [1/min]: 1,500 Year of construction: 1999 Weight [kg]: 2.513
used
Key data: 2000 KW, 2500 kVA, 10000 V
Deutz / MWM Gas CHP (Container) TBG 620 FV 20 Gas-fired power generator (mine gas) from 2003 with 95,000 operating hours, 22,000 operating hours after major maintenance, complete (container) with cooling. 1 available, 1,938 KWel x 1,500 rpm, 10,000 V/50 Hz (transformer 400 V optional). AC generator: AVK DIG 130 l/4, 2,500 KVA Manufacturer: Deutz / MWM Model: TBG 620 FV 20 Type: Gas Engine (Mine Gas) Serial Number: 2204013 Power [KW]: 2,000 Year of construction: 2003 Operating hours: 95,000 / 22,000 after major maintenance Weight motor and generator [kg]: 18.500 Dimensions LxWxH [cm]: – AC generator AVK DIG 130 l/4 Manufacturer: AVK Model: DIG 130 l/4 Type: AC Synchronous Generator Serial Number: 84 25722 A101 Capacity [KVA]: 2,500 Voltage [V]: 10,000 Frequency [Hz]: 50 Electricity [A]: 44 Speed [1/min]: 1,500 Year of construction: 2003 Weight [kg]: 7.100
used
Description: Consisting of polishing stand with brush, polishing stand with sanding plate, double bench grinder from the manufacturer SOLID (type: DS0, speed: 2990 rpm) Total table dimensions: approx. 1000 x 650 mm Approx. Onsite Dimension. (l x w x h): 1,100 x 950 x 1,300 mm, weight approx.: 600 kg
used
Description: 3 parts without content weight approx.: 1,000 kg, Approx. Onsite Dimension. (l x w x h): 3,550 x 1,650 x 950 mm
used
Description: Machine number: 35364 With a combined circular table saw with a milling device and for slot drilling Table dimensions of the slot drilling device: 500 x 260 mm Table dimensions of the combined machine: 1000 x 820 mm Approx. Onsite Dimension. (l x w x h): 1,300 x 1,100 x 1,400 mm, weight approx.: 500 kg
used
Belt conveyor combination 2 x GG 750-760/650 consists of 2 piece belt conveyors each with separate drive Make: Dematic Each conveyor belt length: 750 mm Total length of the combination: 1,550 mm Width: 700 mm Belt width: 650 mm Overall width: 760 mm Conveyor speed: v = 0,7 m/sec without supports without Guide other conveyor speed frequency converter .. Please ask if needed Features: Construction year: 1999 condition: good (used) Conveying length in mm: 750 Nominal / outside width in mm: 700 Belt width in mm: 650 Driven: YES Engine type: SEW Eurodrive Conveyor speed m / s: 0,7 scope of delivery: without supports and side guides Für eine individuelle, fachmännische Beratung setzten Sie sich einfach mit uns in Verbindung. Kontaktieren Sie uns einfach telefonisch oder per Mail. Wir helfen Ihnen gerne bei der Planung und Umsetzung Ihrer Projekte. Wir freuen uns darauf von Ihnen zu hör ...
used
Description: Belt and disc sander Band width 25 mm Strap length 762 mm Grinding wheel dimension 125 mm Tiltable table up to 45 degrees Table surface 130 x 130 mm Connection voltage 230 V Total power requirement 0.3 kW Approx. Onsite Dimension. (l x w x h): 400 x 280 x 340 mm, weight approx.: 9 kg
used
Description: Stone and belt grinding machine Motor power 900 watts. Speed 2950 rpm. Dimensions of whetstone 200 x 32 x 30mm. Dimensions grinding belt 100 x 915 mm. Packaging sizes 62 x 54 x 30 cm. Weight 35 kg. Approx. Onsite Dimension. (l x w x h): 620 x 540 x 300 mm, weight approx.: 35 kg