com used for sale

Sliding table saw milling machine Hammer B3 Perform, very good condition, 4 kW, 2500 mm Format table lengthPrices subject to change, errors, printing and typesetting errors excepted

Circular saw milling machine Bernardo CSM2000, good condition, 3 kW, 315/30 mm, approx. 2200 mm cutting length, approx. 100 mm cutting height, approx. 500 kgPrices subject to change, errors, printing and typesetting errors excepted

5-fold Robland X31 combi, good condition, 2.2 kW, 1500 mm table length, 310 mm table width, 3 knivesPrices subject to change, errors, printing and typesetting errors excepted

5-speed station wagon Robland X310, good condition, 2.2 kW, 3 blades, approx. 500 kgPrices subject to change, errors, printing and typesetting errors excepted

Hardened precision steel bar guided sliding aluminium table Parallel fence with micrometric fine adjustment. Sawblade and milling spindle immersible below the table. Telescopic fence 1800 mm with two flip stops. Stable outrigger table for working heavy plates. With own motor for the scoring unit for an easy deactivation Technical Data: Circular saw: max. sawblade diameter 315 mm spindle diameter 30 mm max. cutting width at parallel f. 1100 mm max. cutting height, 90°/45° 103 mm/72 mm engine power 5 kW S6 (4kW S1) suction diameter 120 mm Spindle shaper: spindle diameter 30 mm spindle tilt 90°/45° spindle travel 175 mm spindle speed 10000/8000/6000/5000/4000/3000 engine power 5 kW S6 (4kW S1) weight 790 kg incl accessories: Sliding table length 2300 mm, scoring unit 4 kW motor, integral fence 500 mm, upper suction, degree raster at outrigger table.

Piston Diaphragm Pump Motor power 5.5 kW Flow rate 6 m3/h Delivery pressure 15 bar The pump was only in operation for 3 years to feed a chamber filter press with vegetable oil

feed pressure: 8 bar Effective free air delivery: 235/165 L/min Receiver capacity: 50 / 10 l / bar weight of the machine ca.: 37,5 kg. Number of cylinders: 2 Stk. motor: 230V / 1,5KW V / KW range L-W-H: 790 x 400 x 730 mm This oil-free and compact Hyundai compressor has a low weight and super-quiet operation. Very quiet, about 53-60dB (Suitable for indoor use) Equipped with: ? safety valve. ? Pressure regulator with pressure gauge and coupling. ? Drain valve on the tank. ? Humidity separator. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Height=1.84 m, Overall length= 0.92 m, Overall width= 0.88 m, Net weight= 246 kg,

This DELTA pallet nailing machine line was manufactured in 2008. It features a comprehensive setup including a base nailer, a nailing machine with pneumatic feeder and nail control, units for marking, turning by 90 and 180 degrees, a corner saw, and a stacking unit, complemented by a conveyor belt. Consider the opportunity to buy this DELTA pallet nailing machine line. Contact us for more information.

This ERREBI TM5 was manufactured in 2000. Designed for wooden pallet and packaging production, it operates on multiple workstations for simultaneous component nailing. Featuring a CNC system, it ensures all movements are controlled with no manual adjustments needed, allowing quick format changes. Optional tools like drills and saws can be added. Contact us for more information about this machine.

This MAYPRO LC2 was manufactured in 2018. It features an industrial PC with proprietary software, PLC integration, and can produce up to 2,000 pallets per 8-hour shift. Minimum and maximum pallet dimensions are 600 mm x 600 mm and 1,500 mm x 1,500 mm, respectively. It includes an automated wood feed system, multi-head nailing, and an integrated stacking system. Total installed power is 20-40 kW. Contact us for more information about this machine.

This SORBINI SmartCoater SP1 was manufactured in 2009. It features a working speed of 5–20 m/min and can handle workpiece widths up to 1,350 mm and thicknesses up to 100 mm. It includes SUPERFICI UV lamps and a VENJAKOB conveyor belt, enhancing its efficiency in wood production. For more information about this machine, please reach out to us.

This Finn-Power LP6 was manufactured in 2007. A robust punching machine featuring a hydraulic punch with a 30-ton capacity and a turret hosting 20 stations, including two Multi-Tool stations. It has a large working area of 3000x1500mm, ideal for extensive production needs. Consider the Finn-Power LP6 machine we have for sale. Contact us for further details regarding this punching machine.

Operating hours: 70792 h Equipment / Additional information: The compressor is water-cooled and has heat recovery. Rated power: 160.0 kW Motor speed: 1500 rpm Max. operating pressure: 8.5 bar Ambient temperature: 3°C/45°C

This MAQUINARIA LDM VPS 2103 was manufactured in 2020. An industrial automated system for wood production, it features a hydraulic nailing system, chain-driven pallet transport, and servo motors for precise block positioning. It operates on 220V or 380V and handles pallet widths from 800 mm to 1500 mm. Safety certified under EN 12100 standards. Contact us for more information about this machine.

Operating hours: 39521 h Equipment / Additional information: The compressor is water-cooled and has heat recovery. Rated power: 110.0 kW Motor speed: 1485 rpm Max. operating pressure: 8.5 bar Ambient temperature: 3°C/45°C

1.0 PCS screw compressor system consisting of the The following components: 1.0 pcs Screw Compressor, Manufacturer: Almig, Type: Belt Drive 15 , Year of manufacture: 2013, Operating pressure: 10 bar, power 15 KW 1.0 pcs. Compressed air dryer Manufacturer: Prematic 1.0 pcs pressure vessel 1.0 Sr. Oil Separator

Key data: 3200 kN, 309 g/PS, 50 mm

Production Line Manufacturing Coffee Capsules NESPRESSO Consisting of the following components: Pos. 01) Injection moulds for capsules, manufacturer: FOSTAG AG 1.0 pcs tool with 16 cavities 1.0 pcs tool with 32 cavities Pos. 02) Two-component injection moulding machine, Bcobrsw Nriue Rvf Nyju Manufacturer: ARBURG, Type: 720A3200-800, Year of manufacture: 2017 The capsules are made as falling parts.

Compressor Boge, CL 4– used - : Ex-location prices (net): 2.950.-€ (net) Manufacturer: Boge Type: CL 4 Year of Make: 2005 approx. 4,000 operating hours Compressed air tank: Manufacturer: BWB H-Nr 540226 Volume: 90L PS 11 bar T.max: 80 degrees T.min: -10 degree K-SK 3400 Ph 16.5 bar Condition: good Available: immediately Location: Waltrop

Manufacturer: KAESER Model: BSD 72 SFC Year of Manufacture: 2012 Machine type: Screw Compressor Rated Power: 37.0 kW Motor Speed: 2960 1/min Max. Operating Pressure: 8.5 bar Ambient Temperature: 3 degrees C / 45 degrees C Until February 2020, this compressor was our main supplier for the system, i.e., between 500 and 700 hours per month. Since February 2020, this compressor has only been used as a backup and during maintenance of the second compressor. The compressor currently has 51,532 operating hours.

Key data: 2 , 10

New AGRE Alup screw compressor with filter unit (technically oil-free), for the operation of milking robots. IMMEDIATELY AVAILABLE from the Hengsberg warehouse in Styria! We are also happy to take care of the delivery and commissioning of the compressor and ongoing maintenance of existing compressors of the brands AGRE, Alup and Atlas Copco. Drive: Efficient IE3 motor with belt drive Control: Infologic² Connect Refrigeration dryer and 270 litre container integrated Includes filtration for technically oil-free operation Performance data Volume flow at operating pressure 9.5 bar: 0.29 m³/min Operating pressure min. / max.: 5.5 / 10.0 bar Total power consumption at 9.5 bar / full load: 3.7 kW Rated power motor: 2.2 kW Pressure dew point refrigeration dryer : approx. +3 °C Dimensions and weight Length x width x height 1540 x 600 x 1350 mm Weight 205 kg Compressed a ...

The Boge Öwamat 6 (identical in construction to the Beko ÖWAMAT 6) is an oil-water separator for the treatment of compressed air condensate. It reliably filters oils and suspended solids from the condensate so that the cleaned water can be discharged directly into the sewer system in accordance with the law.

Key data: 5 , 10

Oil lubricated screw compressor Cooling: Air-cooled design Drive: Efficient IE3 motor, belt drive Control: Speed-controlled with frequency converter Control: Infologic² Connect Refrigeration Dryer: Integrated Filtration optionally available Performance data Volume flow at operating pressure 7.0 bar 0.33 - 0.75 m³/min Operating pressure min. / max. 4.0 / 10.0 bar Total power consumption at 9.5 bar / full load 7.7 kW Rated power motor; IP55 5.5 kW Oil volume 3.2 lt Pressure dew point refrigeration dryer approx. +3 °C Installation data Ambient conditions min. / max. 1 / 46 °C Cooling air demand 1140 m³/h Free fan pressure 30 Pa Sound level 61 dB(A) Voltage / PH / Frequency 400 / 3 / 50 V / Ph / Hz Refrigeration dryer power (230V/50Hz) 0.19 kW Dimensions and weight Length x width x height 1540 x 600 x 1375 mm Weight 230 kg Compressed air outlet 1/2 "  ...

Key data: 7 , 10 , 1

Oil lubricated screw compressor Cooling: Air-cooled design Drive: High-frequency motor with 1:1 direct drive Control: Speed-controlled with frequency converter Control: Aircontrol 5.0 (4-20mA) Refrigeration dryer: Integrated, refrigerant R134a Filtration: incl. cyclone separator Performance data Volume flow at operating pressure 7.0 bar 0.28-1.25 m³/min Operating pressure min. / max. 5.0 / 12.5 bar Total power consumption at 10.0 bar / full load 9.3 kW Rated power motor; IP55 7.5 kW Oil quantity 3.5 lt Pressure dew point refrigerant dryer (20°C 100% RH) +3 °C Installation data Ambient conditions min. / max. 1 / 46 °C ∆ T above coolant temperature 8 °C Cooling air requirement 2200 m³/h Free fan pressure 30 Pa Sound level 62 dB(A) Voltage / Frequency 400 / 50 V / Hz Refrigeration dryer power (230V/50Hz) 0.27 kW Dimensions and weight Length x width ...

Key data: 1 , 10

Oil-lubricated piston compressor Cooling: Air-cooled design Drive: direct-driven piston compressor Including 6 liter container (painted) Performance data Volume flow 270 l/min Operating pressure max. 10 bar Nominal power motor 1.8 kW Number of cylinders 1 Compressor stage(s) 1 Installation data Ambient conditions min. / max. 2 / 40 °C Sound level 73 dB(A) Voltage / Frequency 230 / 50. V / Hz Dimensions and weight Length x width x height 455 x 475 x 500 mm Weight 24 kg Compressed air outlet coupling Compressed air tank capacity 6 lt

Key data: 3 , 10

Oil-lubricated piston compressor Cooling: Air-cooled design Drive: direct-driven piston compressor Including 90 liter container (painted) Performance data Volume flow 330 l/min Operating pressure max. 10 bar Nominal power motor 3.0 kW Number of cylinders 2 Compressor stage(s) 1 Installation data Ambient conditions min. / max. 0 / 40 °C Sound level 79 dB(A) Voltage / Phases / Frequency 400/3/50 V / Ph / Hz Dimensions and weight Length x width x height 1065 x 615 x 1000 mm Weight 89 kg Compressed air outlet coupling Capacity compressed air tank 90 lt

Key data: 4 , 10

Oil-lubricated piston compressor Cooling: Air-cooled design Drive: direct-driven piston compressor Including 270 litre container (painted) Performance data Volume flow 504 l/min Operating pressure max. 10 bar Nominal power motor 4.0 kW Installation data Ambient conditions min. / max. 0 / 40 °C Sound level 79 dB(A) Voltage / Phases / Frequency 400/3/50 V / Ph / Hz Dimensions and weight Length x width x height 1940 x 820 x 1600 mm Weight 150 kg Compressed air outlet coupling Capacity compressed air tank 270 lt

Galvanized compressed air tank Material: Hot-dip galvanized steel Version: upright Fittings: Safety valve, pressure gauge, Ball valve, test valve Installation data Capacity compressed air tank 270 lt Permissible operating pressure max. 11 bar Operating temperature min. / max. -10 / +80 °C Blow-off capacity safety valve 7.24 m³/min Dimensions and weight Diameter 500 mm Height incl. feet 1685 mm Weight approx. 66 kg Compressed air connection 4 x 3/4 "

Steam traps without pressure losses! In the production of of compressed air, water always falls into the form of of condensate. If this condensate is not reliably separated, the condensate can in the compressed air network and damage to the consumers. Performance data Application for compressors up to 6.3 m³/min Application for filters up to 63 m³/min Operating pressure min. / max. 0.2 / 16 bar Capacity discharge 3 l/h Installation data Operating voltage (without el. Connection cable) 230 V Power consumption 10 W IP65 protection class Dimensions and weight Length x width x height 160 x 69 x 116 mm Connection Admission 1/2" Connection outlet 1 x Ø 12 Weight approx. 0.9 kg

Key data: 3 , 40 , 14

Capasity 14,4 m3 Pressure 40 bar rpm 1450 power demand 3,6 kW

Four identical dispensing cells are available, three machines are new and unused, one machine is used. Dispensing capacity: 0.02–0.5cm³/s at mixing ratio 1:1, mixing ratio: up to 1:100, shot volume: 0.005–5cm³, material supply: 20-oz cartridges (600ml), dispensing of small quantities from 5mg per dispensing point, processing of highly abrasive 2K materials. Process: dispensing, mixing, sealing, bonding, potting, protecting, programmable for dispensing dots and beads, suitable for processing abrasive two-component materials, with nozzle control. An on-site inspection is possible.

This HOMAG WEEKE industrial production line was manufactured in 2007. It features a comprehensive setup for high-volume panel processing and edge-banding, including automatic loading systems, a central roller conveyor, multiple edge-banding modules, and a portal manipulator for stacking. Ideal for streamlined wood production, ensuring efficient handling and precision. Consider the opportunity to buy this HOMAG WEEKE industrial production line. Contact us for more information about this machine.

Positioning resolution: 1µm, max. placement rate: 6000cp/h, max. feeder capacity: 310, min. PCB dimensions X/Y: 50mm/50mm, max. PCB dimensions X/Y: 780mm/600mm, PCB thickness range: 0.5mm-3.5mm. Documentation available. An on-site inspection is possible.

Key data: 11

Shamal K60 Suitable for 15 hp, flow rate 1745 l/min This is an original new compressor pump. Compare the measurements with the information in the text and on the photo. This will help you determine if it's the right pump. X=245mm Y=300mm D=550mm All employees speak Dutch, German and English. Prices are exclusive of VAT. Shipping is possible (at an additional cost). (Subject to changes and errors in technical data, information and prices as well as prior sale.)

Shamal K30 Suitable for 5.5 / 7.5 hp / 4 / 5.5 kw, flow rate 900 l/min This is an original new compressor pump. Compare the measurements with the information in the text and on the photo. This will help you determine if it's the right pump. X=190mm Y=225mm D=400mm This compressor pump is used by several compressor manufacturers. All employees speak Dutch, German and English. Prices are exclusive of VAT. Shipping is possible (at an additional cost). (Subject to changes and errors in technical data, information and prices as well as prior sale.)

Key data: 22 , 8 , 2

Atlas Copco SF22+ Compressor Atlas Copco CD45+ Dryer Sold as a set. Oil-free air compressor Pressure: 8 bar Flow rate: 2.4 m³/min Power: 22 kW Weight: 687 kg Year of construction: 2024 As good as new Unused device All employees speak Dutch, German and English Prices plus VAT Shipping available for an extra charge (Subject to changes and errors in technical data, information and prices as well as prior sale)

Compressors Nirvana oil-free variable speed screw compressors 55-75 kW it ran 19138 hours. Nirvana oil-free compressors, with a matching variable speed inverter and hybrid permanent magnet motor (HPM®), offer unparalleled energy efficiency at all speeds and outstanding reliability. They deliver ISO 8573-1:2010 Class 0 certified, 100% oil-free air for the most critical applications Find more here - .ucymachines/ Contact us at - sales@ucymachines

Thermostat housing incl. thermostats and entire interior Mitsubishi No.: 37546-23701

Refrigeration Compressor / Condenser Unit Second Hand Manufacturer: Franchill Ltd Model: SP3X45-RDM-FS 400V-1PH-50Hz Compressor / Heater Model: ZB45KCE-TFD 3 x 4.6kw For more information and more available stock please visit us at - advancedbrewing.co.uk

This 3-axis TRUMPF Trumatic 600L was manufactured in 1996. It features a maximum punching force of 220 kN and a laser power of 1,500 W, making it suitable for various applications. With a machine weight of 18,000 kg, it offers robust performance. If you are looking to get high-quality punching and laser capabilities, consider the TRUMPF Trumatic 600L punch-laser combination we have for sale. Contact us for further details.

Compressor with built-in air dryer Power: 25 kW Pressure: 8 bar

Compressor with built-in air dryer Power: 25 kW Pressure: 8 bar

2008 HEIDELBERG STAHLFOLDER KH 78/4K-TK KH78+SPH-70+PFH 82 16 pages

An oil-lubricated screw compressor Boge including an air dryer unit is available. Tank volume: 350l, motor power: 11kW, max. operating pressure: 8bar, air flow rate: 1810l/min, machine dimensions X/Y/Z: approx. 2000mm/750mm/1400mm, weight: approx. 400kg. An on-site inspection is possible.

A screw compressor Atlas Copco including an air dryer is available. Air volume flow: 5.88m³/min, max. operating pressure: 10bar, motor power: 37kW, speed: 2960rpm, operating hours: approx. 49696h. Including air dryer Atlas Copco FD 95. Documentation available. An on site inspection is possible.