cnc turret punch used for sale

connected load frequency: 220 V rated current: 263/152 : 01516 81 663 694 weight of the machine ca.: 1 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 160 t no. of strokes: 40 - 120 Hub/min sheet width: mm total power requirement: 40 kW Pressing capacity 160 ton Table clamping area 1,100 x 1,280 mm Ram clamping area 850 x 890 mm Distance between guides 1,120 mm Distance between columns (below guide ways) 1,350 mm Distance between Table and ram in upper position approx. 400 mm No. of strokes 40 - 120 /min Adjustment of stoke 67 / 115 / 160 mm Ram adjustment, motor driven 125 mm Ejector travel 50 mm Total electrical load, approx. 40 kW - 500 V - 50 Hz Weight, approx. 24,000 kg Accessories / Special Features WEINGARTEN Sheet Metal Uncoiler with overhead loop control (space saving because it does not need a loop-pit). Strip width 375 mm. The loop control guides the strip-material from the uncoiler to the machine thru a straightening device with automatic supervision. 8-track slide bearing guide. Automatic oil-circulation lubr ...

Three Illig punching machines are available for the precise punching of thermoformed plastic parts from film material. Working width: approx. 900mm, working height: approx. 120mm, roller diameter: approx. 196mm, machine dimensions X/Y/Z: approx. 2500mm/1300mm/1600mm, weight: approx. 750kg. Including two hydraulic punching machines Wolf EHPT 6E and two manual swivel arm punching machines. On-site inspection is possible.

A Schön swivel arm punching press and a Hang eyeletting machine are available. 1) Swivel arm punching machine Schön & Cie 8L, year of manufacture: 1973, pressing force: 18t, table dimensions X/Y: 900mm/450mm, swivel arm width: 350mm, stroke: 60mm, passage height: 83mm-183mm, oil capacity: 40l, weight: approx. 1200kg. 2) Eyeletting machine Constantin Hang 103 SCD KG, year of construction: 1993, machine dimensions X/Y/Z: approx. 600mm/1250mm/700mm, weight: approx. 50kg.

sheet width: - mm plate length: - mm plate thickness: - mm total power requirement: - kW weight of the machine ca.: - t dimensions of the machine ca.: - m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Swivel arm punch Sandt, in good condition, immediately available Robsvvhfuer Sb Nwkju If you are interested, we will also be happy to inform you about other machines in our company. You are welcome to visit the machine in our house by prior appointment.

Heidelberg Embossing Crucible TP, Machine Number T169693+ Heidelberg Embossing Crucible TP,T191298, Machine is in good condition, immediately available Rebevvikfer Sb Nwkju If you are interested, we will also be happy to inform you about other machines in our company. You are welcome to visit the machine in our house by prior appointment.

Pressure plate punch Beil 780/425-S-H-AP2; cleaned and tested; die-cut 780 and 425 mm autoplate; Investment Contact. Plate punch hatchet 780/425-S-H-AP2; cleaned and checked; punch size 780 and 425mm Autoplate; contact for plate.

Bridge punch from Sandt with 30t

Atom cart beam punch with 25t. The machine is fully functional.

Bridge punch of the company Schön, model 64035 / 92 The machine is fully functional.

Sheet format: max. 1060 x 746 mm, min. 400 x 350 mm Equipment: Stripping station, depaneling, centerline, floor storage in depaneling station, Quick-Lock quick-release closing frame, max. machine speed 9,000 sheets/hour, max. die-cutting pressure 260 tons, processable materials: paper min. 70g/m², cardboard / solid board max. 1,000 g/m², corrugated cardboard up to 2 mm. Condition: Not operational Sale exclusively as spare parts donor Missing parts: Pumps, Grippers, Chain, Cube, Various Electrical Components Other: Machine can be visited by arrangement.

punching pressure: 16 t plate thickness: 8 mm plate length max.: 1250 mm sheet width - max.: 1000 mm engine output: 13 kW control: Cadman CNC voltage: 400 V weight of the machine ca.: 8,3 t dimensions of the machine ca.: 3600 x 2300 x 2000 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

L-profile: 120 x 120 x 10 mm flat steel: 300 x 15 mm round/square steel: 40 mm punching: dia 28 x 13 mm U/I-profile: 100 mm

hydraulic: ja : 100 t weight of the machine ca.: 2,9 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Punching machine Pneumatic Presser Serial-No. 17063-

Automatic Signature Punching Machine / Automatische Stanzmaschine JAMES BURN Lhermite EM 520 Baujahr / Year 1998 - Serial-No. 211661 Format Einlaufbreite / Size Infeed width 520mm Materialdicke / Thickness max. 3mm (32 pages 80 gr) Geschwindigkeit / Speed max. 10.000cycles/h Papierstärke / Paper thickness 70 to 300 gr.  James Burn Lhermite EM520 is an Automatic Signature Punching Machine.  It can be used for inline or offline production. With Feeder and Jogger delivery. The EM520 features the state of the art modular system for  punching and cutting signatures in line 

Manufacturer: Amada Model: EM2510NT Year of Manufacture: 2011 Machine Weight: 16500 kg Type of Machine : Punching Machine Operating Hours: 14272 Control Unit Manufacturer: Fanuc Model: Series 180I PB Find more here - / Contact us at -

Manufacturer: FINN Model: POWER LP6 Year of Manufacture: 2007 Working hours: 21,500 available : immediately Find more here - / Contact us at -

Manufacturer: FINN POWER Model: LPe5 Year of Manufacture: 2002 Work area: 2500×1250 mm (+ repositioning) AVAILABLE: immediately Find more here - / Contact us at -

pressure: 60 t stroke: 60-80 mm no. of strokes: 60-300 Hub/min weight of the machine ca.: 10 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15

Single column - eccentric press WEINGARTEN type ERV 40Masch. No. 537 / 65 Year of construction 1965Compressive force 40 ton. Projection 230 mmTable size 570 x 470 mmPlunger area 250 x 200 mmClamping pin hole 40 mmInstallation height max. approx. 520 mmStroke adjustment 8 - 88 mmPlunger adjustment range 63 mmStroke rate 70 strokes per minuteDrive power 3 kWNetz connection 380 volts, 50 Hz- Table height adjustment- Overload protection by crushing plate- Clutch-brake combination by WEINGARTEN friction threaded coupling-

Single column - eccentric press WEINGARTEN type ER 63Masch. No. 52A / 63 Year of construction 1963Pressure capacity 63 ton. Projection 280 mmTable surface 630 x 530 mmAdjustable plunger stroke 8-100 mmPlunger adjustment 63 mmStroke rate 65 strokes / min. Engine power 4 kWNetz connection 380 Volt, 50 Hz- Clutch-brake combination by WEINGARTEN friction threaded clutch- Electrical stroke release via foot switch- Wheel counters- Overload protection by crushing plate- Front crankshafts Support bearingSpace requirement L x W x H 1500

Single column - eccentric press PELS - RICHTER type PEKR 125Masch. No. 20684 Year of construction 1967Compressive force 125 ton. Projection 430 mmTable size 1100 x 750 mmPlunger area 890 x 650 mmTable opening 400 mmStroke adjustment 6 to 115 mmRam adjustment 100 mmInstallation height largest stroke top max. 450 mmClamping pin bore 50 mmStroke rate 60 strokes/min. Table height above floor 900 mmMotor power 7.5 kWNerg connection 380 volts, 50 Hz- overload protection by crushing plate in the plunger- compressed air

Eccentric punching machine HAULICK + ROOS type RVD 125Double column - Eccentric pressMasch. No. 212560 Year of construction 1981Compressive force 125 ton. Table size 880 x 800 mmTable opening 470 x 140 mmStand width 900 mmStand width laterally 415 mmRam stroke 45 mmRam adjustment range 0-80 mmInstallation height in the picture 340 mmStroke rate 50 to 300 strokes/min. Engine power main drive 22 kWNe-connection 380 Volt, 50 Hz- Double connecting rod engine with 4-bearing eccentric shaft for off-center tappet pressure

Single-column eccentric press MÜLLER GEFREES type PDET 5 S/EKMasch. No. Year of manufacture 1988Compressive force 5 ton. Projection 125 mmColumn passage 170 mm Table surface 280 x 220 mmWaste height 90mmLifting area 160 x 100 mmLifting adjustment 4 to 40 mmRam adjustment 30 mmInstallation height largest stroke at the top max. 210 mmStroke rate 200 strokes/min. Clamping pin bore 25 mmTable height above floor 900 mmEngine power 0.55 kWNerg connection 380 volts, 50 Hz- pneumatic clutch-brake combination-

Single-column eccentric press WEINGARTEN type E 40Masch. No. 643/62 Year of construction 1963Pressure capacity 40 ton. Projection 250 mmTable opening 150 x 80 and 200 mmTable area 560 x 460 mmPlunger area 250 x 200 mmPlunger stroke adjustable 8-88 mmPlunger adjustment 63 mmInstallation height 320 mmPin hole 40 mmStroke rate 100/130 strokes / min. Motor power 2.2 / 3 kWNetz connection 400 volts, 50 HzTable height above floor 840 mm- Clutch-brake combination by WEINGARTEN friction threaded coupling with TDC

Hydraulic punch, punching rack for the use of punching units JOKA type HP-SHydraulic hole punch, hydraulic press for punching bracketYear of construction approx. 1995Printing capacity 5 ton. Projection 155 mmStroke approx. 20 mmPunching unit width max. 54 mmPunching unit height max. 220 mmDie holder 48 mmMotor power 1.5 kWNeching connection 230 volts, 50 Hz- for the universal use of punching units JOKA SW 20 or SWD 20- Projection of the punching units can be larger, can be pushed through to the rear- Stroke release via

A complete punching system with a grid punch is available. 1) Double reversible decoiler, load capacity: 1000kg. 2) Alba GGVHY 200 straightening machine, year of manufacture: 1992, feed rate: 6.5m/min, max. material width: 200mm, max. material thickness: 4mm, transport rollers: 2. 3) Alba MA RIA 7 feed, year of manufacture: 1978, max. material width: 300mm, max. material thickness: 3mm, feed rate: 40m/min, control: Siemens S7. Material thickness: 3mm, feed speed: 40m/min, control: Siemens S7 with OP7. 4) Punching machine Raster HR 80/700 NL, year of manufacture: 1992, pressing force: 80t, stroke rate: 250/min, table dimensions X/Y: 730mm/750mm, ram dimensions X/Y: 730mm/630mm, ram stroke: 40mm, ram adjustment: 80mm. 5) Profiling machine CIS. Documentation available. On-site inspection is possible.

A complete punching system with a grid punch is available. 1) Reel Gebrüder Kemmerich 7VID, year of manufacture: 1981, max. load: 1000kg. 2) Straightening machine, max. material width: 300mm, max. material thickness: 2mm. 3) Feed unit Alba UVHY 300/0.1, feed speed: 6.5m/min, max. material width: 300mm, max. material thickness: 4mm, transport rollers: 2. 4) Punching grid HR 50/600 NL, stroke rate: 300/min, stroke: 30mm-80mm. On-site inspection is possible.

Key data: 75 t, 80 mm, 120 1/min

Pressure 75 t Stroke rate 120-600 / min Sheet width 10-300 mm Table size 1050 x 820 mm Pusher clamping surface 960x820 mm Distance table - UK plunger 380 mm Adjustable stroke - max. 80 mm Feed length 0-150 mm Total power requirement 20 kW Machine weight approx. 13 t Feed unit with max. belt speed 70 m/min Eccentric shaft with 4-fold bearings 2 connecting rods Central lubrication incl. magnetic belt conveyor - in use until 2020 -Operating instructions -Manual - Circuit diagram etc..

A cylinder roll punching machine Adolf Illig is available. Pass-through width: approx. 850mm, pass-through height: approx. 120mm, roll diameter: approx. 190mm, table dimensions X/Y/Z: 2x approx. 1200mm/1200mm, working height: approx. 800mm, machine dimensions X/Y/Z: approx. 2700mm/1350mm/1550mm, weight: approx. 900kg. An on-site inspection is possible.

A punch riveting tool Böllhoff is available. Documentation available. An on-site inspection is possible.

Amada punching machine EMK 3610NT incl. loading unit MP300 for sale. We would like to hand over the machine complete with tools and Wilson X-Sharp grinding machine.

max. format 54 x 72 cm Built in 1960 Inking unit not complete for punching / embossing Price on request. We supply and install worldwide.

A brought cylinder Heidelberg 40x58cm

Inv. Num. : 5955 Type: Trumatic 500 R Producer: Trumpf Created: 2003 Parameters: Control system: TRUMAGRAPH CC 220 S Switch-on hours: 29433 h Compressive force: 22 t Machine height: 2200 mm Machine length: 6900 mm Machine width: 5800 mm Machine weight: 11000 kg 2020: Replacement of hydraulic hoses

Max. punching force: 500kN, max. punching stroke: 200mm, max. punching area: 1800x750mm, connected load: 39kVA, length: 6500mm, width: 3900mm, height: 2900mm, net/operating weight: 7.8/10.2t, operating hours: 56,645h, with documentation. The machine has been regularly maintained, hydraulic unit integrated into the machine frame, with PC control. An on-site inspection is possible.

Features: automatic non-stop delivery with conveyor, non-stop feeder with rods, pull mark left, push mark right, quick clamping frame for tooling, lower stripping station, upper stripping station, two exchange frames for lower stripping station. Without die-cutting plates. Processable materials: min. paper 90g/m², max. solid board 2000g/m², max. corrugated board/ with MasterSet 4/ 2mm, max. sheet size 760x1060mm, min. sheet size/with MasterSet 300x350/ 350x400mm, max. cutting pressure: 2.6MN/ 260t, max. machine speed: 8000 sheets/h, max. feeder pile height without non-stop/ in non-stop operation: 1500/ 1200mm, max. feeder pile weight: 1500kg, max. delivery pile height: 1400mm, max. delivery pile weight: 900/ 1340kg. Operating hours: 1525h. An on-site inspection is possible.

Max. punching force: 300kN, max. punching stroke: 200mm, max. punching area: 1800x750mm, connected load: 11kVA, length: 4800mm, width: 3400mm, height: 2800mm, net/operating weight: 10/13t, operating hours: 2818h, with documentation. The control was renewed in 2022. The machine has been regularly maintained, hydraulic unit integrated into the machine frame, with PC control. An on-site inspection is possible.

Max. punching force: 500kN, max. punching stroke: 200mm, die support dimensions: 13,200x1500mm, conveyor belt dimensions: 7435x1995mm, max. punching area: 1800x750mm, max. strokes: 80/min, connected load: 34kVA, length: 6500mm, width: 3900mm, height: 2900mm, net/operating weight: 7.8/10.2t, operating hours: 52,680h, with documentation. Equipped with extraction system, rotatable tool enabling nesting, tension-free unwinding possible. The machine has been regularly maintained, hydraulic unit integrated into the machine frame, with PC control. An on-site inspection is possible.

Met elektrische achteraanslag Ponscapaciteit: 70 ton Dia x plaatdikte: Ø 28 x 20 mm Maximale slag: 80 mm 40 str / min Keeldiepte: 300 mm Werkhoogte: 1065 mm Maximale snijdikte in plaat: 20 mm Bladlengte: 455 mm 90°-snede: 130 x 130 x 13 mm 45°-snede: 90 x 90 x 10 mm Op maat gesneden rond/vierkant: 45 mm Elektromotor (vermogen): 7,5 kW Lengte: 1800 mm Diepte: 1200 mm Hoogte: 2000 mm Gewicht: 1650 kg

Max. cutting force: 220kN, laser power: 3200W, nitrogen connection: 30bar, oxygen connection: 20bar, connected load: 76kVA, operating hours at the beginning of 2025: 67,766h, with Trumpf TLF 3200 laser and RIEDEL L 15/21 TR3/19.00 cooler, refrigerant: R134a, filling weight: 11.5kg, high pressure: 20.2bar. Tools additionally available. An on-site inspection is possible.