cnc sheet bending used for sale

Technical data: - Bending capacity - steel pipe of 20 - 60 x 4 mm - - stainless steel pipe of 20 - 50 x 3 mm - max. resistance moment 6.2 cm - max bending angle 180° - max radius 125 mm - Bending speed 8 sec - Drive 400 V / 3 kW - Space requirement approx. L 2400 x H 1600 x D 1000 mm - Weight approx. 1400 kg - with: - Bending angle control via potentiometer with digital display - 6-fold bending angle preselection - Indoor + external pipe deburrer - Bending tools Rx2.5D x 38 ; • 50 , 65 ;

Qty. 1 Second-hand JCO pipe press bending line Mfc.: Samyul, ROBO, Shinsung, ChangSong, Rotech, FANUC, Hyupshun, Ingersoll Built: 2003, 2008, 2009, 2013, 2014 Plate material: Mild steel Plate dim.: 16.0 x 5.2 x 0.08 m – L x W x T Pipe dia.: Φ400~Φ1650 mm Pipe Length: 6.0m ~ 16.0 m Scope of supply: JCO Hydraulic Press Tack Welder Machine Sealing Welder Pipe Heating & Rotating Device Inside Welder Outside Welder Calibration Presses Milling Cutter Cutting Machine Bevelling Machine Compressor

M. No.: 121

Robust, high-quality round sheet bending machine for already profiled workpieces (sheet blades) - with motor drive at the bottom and top adjustable workpiece width between 300 mm and 800 mm, largest sheet thicknesses which can be bent round copper / titanium zinc / aluminium 0.8 mm - galvanized steel sheet 0.7 mm - stainless steel sheet 0.5 mm, smallest possible bending radius 350 mm - bending radius depending on the yield strength - smallest bending radius galvanized steel plate 0.7 mm - 1,000 mm, continuous speed infinitely adjustable 1 to 6 m/min, drive capacity 2 x 0.75 kW, weight 375 kg

Technical data: - bending and rolling by hand, - max working width 1020 mm - max. material thickness St 40 1.25 mm - Bending angle adjustment via end stop 10 - 180 ° - max hub upper cheek approx. 85 mm - max. adjustable bending cheek 20 mm - Shaft diameter 55 mm - Upper shaft can be swivelled - Rear shaft parallel + obliquely adjustable - Space requirement approx. W 1500 x H 1400 x D 750 mm - Weight approx. 400 kg

Press brake edge machine edge bench press used Manufacturer: Mengele Type: C320-4B Built: 1966 last revision and repair: 2000 Location D-01587 Riesa Dimensions WxH: 6,250 x 3,650 mm Edge knife width: 6,150 mm sheet thickness at 6,000 mm bending length: approx. 7.5 mm. The machines are designed for very deep shaft bends, therefore very deep cheek recesses. Original 300 t pressing force - In 1989 the pressing force was increased to 350 t. The press is in very good condition despite its age. The machine is disassembled and ready for loading. documentation for the machine is available. Weight: about 45 t

Mechanic plate bending machine Goyar 3C-25/20. Bending lenght: 2000mm. Bending capacity: 25mm. Diameter of upper cylinder: 285mm. Diameter of lower cylinders: 235mm. Main motor power: 20cv. Bending speed: 5 mpm. Weight: 5500Kgs.

M. No.: 6513/19

specifications: - Pressure capacity 100 KN / 10 t - Compressive force adjustable 0 - 100 kN - Stroke length 0 - 150 mm - Clear width approx. 200 mm - Lifting speed 0 - 0.6 m/min - Tool height up to approx. 100 mm - Bending performance - with prism MW 100 flat to approx. 100 x 12 mm - Tube bending up to approx. 1 inch - Directional power Wy at straightening block distance of 1m 100 cm³ - Drive 400 V / 1.1 kW - Space requirement approx. W 1100 x H 1000 x D 650 mm - Weight approx. 400 kg

sheet width: 1500 mm plate thickness: 1,5 mm distance between columns: 1500 mm bending angle max.: 135 ° total power requirement: - kW weight of the machine ca.: 0,36 t dimensions of the machine ca.: 1,7 x 0,7 x 1,3 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tube diameter: . mm wall strength: . mm bending radius min.: . mm Control: total power requirement: kW weight of the machine ca.: . t dimensions of the machine ca.: . m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 95 mm Shaft diameter: 30 mm Shaft revolutions: 7 U/min roll diameter: 132 mm Drive: 0,75 kW weight: 220 kg range L-W-H: 530x900x660 mm Equipment / Accessories: - Two driven rollers with grooved surface - Manual feed of the upper roller - working position horizontal and vertical (with tilting base) - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn different profiles are used e.g. Flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

The HKB series swivel machines are used for bending thin sheet metal. Due to their compact design, they fit easily into small workshops and cover a wide range of applications with their segmented upper tool. With an adjustable angle stopper, these swivel machines are also suitable for the production of small batches. Compact and torsion-resistant Segmented upper tool for many bending options Integrated, manual bend compensation Adjustable angle stop for series production Hands free Foot control of the upper bolster clamp Workspace Working length 1270 mm Sheet thickness (max.) – 400 N/mm² 2 mm Dimensions (length x width x height) 1.6 m x 0.9 m x 1.18 m Weight 330 kg Angle range of the bending beam 135°

round material: 40 mm tube diameter: 70x2 mm square material: 80x30x3 mm L-beam: 50 x 5 mm I - beam section - flat steel: 80 x 16 mm I-beam section - upend: 50 x 15 mm roll diameter: 157 mm Shaft diameter: 50 mm bending speed: 2,95 m/min total power requirement: 1,1 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: 1000x950x1450 mm Domestic equipments: - Special steel shafts (42CrMo4) hardened and ground - a set of standard rollers - lower rollers up and down hydraulically deliverable - digital display for lower rollers - separate control panel - in one direction manually adjustable lateral straightening rollers - manual lubrication - horizontal and vertical operation - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Two driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

BLM DYNAM 3 CNC tube bending machine was built by BLM S.P.A. in Italy in 1999. Distinguished by its high productivity and bending accuracy, the machine is an indispensable tool in any production facility. The applied technical solutions and reliable components make it possible to perform fully automatic, serial bending of profiles and tubes with a maximum diameter of 60 mm. All process parameters are entered on an intuitive CNC controller with many functions that facilitate the programming of even the most complex shapes in just a few steps. Throughout its lifetime, the DYNAM 3 mandrel bending machine has been regularly serviced. The total weight of the machine is 5070 kg. Technical specifications of the BLM DYNAM 3 CNC tube and profile bending machine - CNC control system: BLM FNC 2000 R - maximum tube diameter: 60 mm - tool set for bending tubes Ø 25 mm - lubricant pump: FLENCO ...

: 80 mm roll diameter: 260 mm : 7 U/min : 170 mm : 27 kN : 160 mm : 450 mm total power requirement: 3,7 kW dimensions: 980x1430x1600 mm weight: 1380 kg Accessories / equipment: - Three driven rollers with a smooth surface - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can bend different profiles are used e.g. Flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: R10-R260 : 210 ° bending speed: 2 U/min : 1 1/4 x 3,5 mm : einphasig - 230 V drive motor: 1,1 kW : < 70 dB weight of the machine ca.: 80 kg dimensions of the machine ca.: 410 x 1000 x 570 mm Accessories / equipment: Hard copper and aluminum: 54x2 mm Steel tube: 42x3 mm Stainless steel: 42x2.5 mm Solid material: 30 mm Number of programs: 30 each 9 bends Control: Soft-touch control panel in 8 different languages Mobile by driving device The controller allows easy programming of the automatic cycle The controller is equipped with a system diagnostics and has a great language selection. Patented fast tool change system A single bending speed The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 48x3,5 mm : 48x2,5 mm : 32 mm : 64x2 mm bending speed: 2 U/min : R10-R300 total power requirement: 1,5 kW weight of the machine ca.: 110 kg dimensions of the machine ca.: 410x1000x570 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bar material - diameter: Ø 35 mm I-beam section - flat steel: 60x10 mm L-beam: 50 mm tube diameter max.: Ø 60x2 mm square material: 45x45x3 mm roll diam. toproll: 162 mm roll diam. bottom roll: 152 mm Shaft diameter: 50/40 mm turning speeds: 3,3 m/min total power requirement: 1,5 + 0,75 kW weight: 450 kg range L-W-H: 1050x950x1450 mm Domestic equipments: - hydr. Delivery of the top roller - standard roller set - side straightening rollers - Upper roll holder: 50.0 mm - Under roller diameter: 40.0 mm - Control panel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW range L-W-H: 1100x850x1350 mm weight: 495 kg Equipment / Accessories: - Two driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - Footswitch - standard roller set The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

L-beam: 50x5 mm square material: 50x40x3 mm I - beam section - flat steel: 120x15 mm I-beam section - upend: 60x10 mm round material: Ø 35 mm tube diameter: Ø 70x2 mm roll diameter: 155 mm bending speed: 4,3 m/min bore: 50 mm total power requirement: 1,5 kW weight: 400 kg dimensions: 830x730x1350 mm Domestic equipments: - Extended special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

I-beam section - flat steel: 80x20 (d1200) mm I-beam section - upend: 80x25 (d2100) mm L-beam: 50x50x6 (d1000) mm bar material - diameter: 40 (d800) mm square material: 60x60x3 (d4000) mm rectangle: 80x30x3 (d6000) mm tube diameter max.: 70x2 (d1600) mm tool adaptor: 60 mm roll diameter: 177 mm bending speed: 6,4 m/min total power requirement: 4 kW machine weight ab.: 970 kg Overall size: 1400x950x1450 mm Domestic equipments: - hydr. roller drive - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW range L-W-H: 900 x 600 x 1000 mm weight: 470 kg connected load: 400/50 V/Hz Equipment / Accessories: - Three driven rollers - Manual delivery of the upper roller - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

shaft diameter: 60 mm Shaft revolutions: 6 U/min roll diameter: 215 mm pressure hydraulic cylinder: 180 kN dimensions: 1125x870x1620 mm weight: 820 kg Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW weight: 495 kg range L-W-H: 1100x850x1100 mm Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 63x4,2 mm external diameter: min. Ø 5 mm bending radius min.: 10 mm bending radius max.: 270 mm Bending Angle: max. 210 ° bending device: gegen Uhrzeigersinn total power requirement: 0,75 kW weight of the machine ca.: 130 kg dimensions of the machine ca.: 740x470x1030 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 215 mm shaft diameter: 60 mm Shaft revolutions: 6 U/min : 100x2 mm : 80x15 mm pressure hydraulic cylinder: 180 kN total power requirement: 2,2 kW weight: 720 kg dimensions: 1200x900x1700 mm Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 60x3 mm : 60x2,5 mm : 35 mm : 64x4 mm : R10-R300 bending speed: 2 U/min total power requirement: 1,5 kW weight of the machine ca.: 130 kg dimensions of the machine ca.: 595x363x900 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 200 kN stroke length max.: 200 mm working feed: 10 mm/sec return speed: 20 mm/sec : 480x1060 mm work height max.: 900 mm toolpiece height max.: 200 mm total power requirement: 2,2 kW : 200x12 mm bending capacity max. - round: 48x4,0 mm weight: 500 kg Overall size: 1010x480x1120 mm Domestic equipments: - with semi-automatic control (99 programs with 16 steps each) - including bending bolt (without punch) - Tool holder for dies - Foot pedal Equipment: - Stamp, small U = 145 mm 85 °, H = 200 mm, R = 5 mm - Quick change monometer 85 °, H = 200 mm, V = 63 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2020 mm plate thickness: 1,5 mm distance between columns: 2050 mm Daylight opening: 100 mm total power requirement: 0,75 kW weight of the machine ca.: 1 t dimensions of the machine ca.: 2,7 x 1 x 1,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: 2 castors hydraulically adjustable 3 rollers driven Resistance torque: 80 cm³ Shaft diameter: 100 mm Roll diameter: 315 mm lateral hydr. Controlled arm correctors left and right CE. Mark Bending capacity square: 120 x 60 x 5 mm Bending capacity flat steel: 130 x 25 mm Bending capacity tube: 114.3 x 6 mm Bending power angle: 100 x 10 mm Round steel: 80 mm Motor power: 11 kW Control panel with digital display Dimensions (length x width x height): approx. 1750 x 1850 x 1650 mm Weight: approx. 3.6 tons Accessories: Various bending rollers Condition: we will still carry out a complete service on the machine The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.

: 50 (500) mm : 45 (500) mm L-beam: 80 x 80 x 8 (800) mm T - beam - web outwards: 80 x 9 (800) mm Axis diameter: 60 mm work speed: 5,0 m/min Tool diameter: 195 mm total power requirement: 3 kW weight of the machine ca.: 1,0 t dimensions of the machine ca.: 1,2 x 0,9 x 1,2 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

chamfer lenght: 480 - 4045 mm 4 pieces of unused upper tools: tool No 5 length: 3050 mm, dimensions see sketch, price = 710,- tool Nr 6 Length: 3073 mm, dimensions see sketch, price = 970,- tool No 9 L = 1925 mm divided, dimensions see sketch, price = 850,- tool Nr.10 length: 1520 mm, dimensions see sketch, price = 850,- Prices excl. VAT Machine dealer with own stock of 2500 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

PLATE BENDING MACHINE FACCIN - 4 ROLL HYDRAULIC 3000 X 40 MM - MODEL 4HCI3-35/30 YEAR 1990 /2025 PLATE BENDING ROLL LINEAR GUIDEWAYS DOUBLE PINCH PRE-BENDING Machine in good working condition Bending capacity -Plate width : 3000 mm -Rolling plate thickness 40 mm - Prebend thickness 35 mm Rolls dimensions: -Useful length 3050 mm -central rolls upper/lower D 470 mm -side rolls left/right D 420 mm • Hardening of the 4 rolls high strength surface • 3 rolls driven powered with gear unit with hydraulic motor • Conical bending attachment side rolls tiltable to form cones, contrast pad roller type. • Opening front hydraulic drop-end to unload the closed shell. • Variable speed working roll bending rotation hydraulic speed fas ...

HEIDELBERG Nela Plate Bending suitable for HD SM 52 / 74 /102 and XL machines different years of construction available

roll diameter: 76-86 mm Shaft diameter: 20 mm Shaft revolutions: 11 U/min Bending capacity round tube: 30 mm : 25x6 mm Angle iron: 20x20x4 mm Drive: 0,18 kW range L-W-H: 530x420x500 mm weight: 80 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßerb CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

sheet width: 2020 mm plate thickness: 2 mm distance between columns: 2030 mm bending angle max.: 135 ° total power requirement: - kW weight of the machine ca.: 1,22 t dimensions of the machine ca.: 2,5 x 1,0 x 1,4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

I-beam section - upend: 100 x 20 (d 2100) mm tube diameter max.: 100 x 3 (d 3000) mm L-beam: 80 x 80 x 8 (d 2000) mm square material: 50 x 25 x 2 (d 600) mm bar material - diameter: 60,0 (d 1000) mm I-beam section - flat steel: 120 x 30 (d 600) max. 140 mm tool taper: 80,0 turning speeds: 4,2 U/min weight: 1600 kg dimensions: 1240 x 1375 x 1540 mm Domestic equipments: - Welded steel structure (St-52) - Rollers are driven by 3 separate hydraulic motors - Stepless speed - Special steel gears - Shafts are made of special steel, hardened and ground - Manual lubrication - Guide rollers are hydraulically adjustable - Lower rollers are hydraulically movable up and down - Infinitely adjustable speed of the lower rollers, move after below and above - Digital display for lower rollers - Separate and movable control panel - Horizontal and vertical operation - Production quality certified according  ...

MACRI ITALIA PROVAR 6-45 U-D tube and profile bending machine was built in 2015 in Italy by Macri Italia srl. The machine, designed for precision bending of tubes and profiles with a maximum diameter of 45 mm, is an answer to the daily challenges of modern business. The machining process is performed by means of a moving head with reinforced gears, which allows the bending of standard and variable radiuses in 6 axes (X,Y,Z,B1,B2,A). Each axis, in turn, is driven by brushless servomotors, which ensure the achievement of high dynamics, combined with excellent positioning accuracy. The machine’s extensive range of equipment includes e.g. state-of-the-art MACRI software with many useful functions and the ability to run a anti-collision test with 3D simulation. The PROVAR 6-45 U-D mandrel bending machine weighs 4000 kg. Technical specifications of the MACRI ITALIA PROVAR 6-45 U-D tube be ...

Inv. Num. : 5725 Type: A 89 TNCB Producer: CSM Created: 2014 Parameters: Maximum bending angle: 180 pcs Total power requirement: 15 kW The largest profile: 60x60x6 mm bending radius in the middle of the tube: 350 mm bending radius in the middle of the profile: 300 mm Machine height: 1200 mm Machine length: 4700 mm Machine width: 1200 mm Machine weight: 2500 kg

DAVI MCA 1513 4-roll plate rolling machine was built in 2023 in Italy by Promau S.r.l.. This highly efficient machine is the perfect choice for precision rolling of cylindrical, elliptical and conical forms. Sheet metal with a maximum thickness of 6,5 mm is machined fully automatically by four rollers, which are driven by planetary gears. In turn, the advanced control system allows, among others, the generation of a full programme from CAD files and an offline performance test. The offered DAVI MCA 4-roll plate bending machine is a guarantee of achieving repeatable parts of the highest quality. Technical specifications of the DAVI MCA 1513 plate rolling machine - number of rollers: 4 - maximum sheet metal thickness (mild steel, yield point 260 MPa): 6,5 mm - maximum sheet metal length: 1500 mm - control system: DAVI - motor power: 5.5 HP - power supply of the MCA 1513 machine: 4 ...

Unbek. Type, YOC ca. 1990, Revision 2002 Specifications: - Bending capacity at 45 kg / mm² up to approx. Ø 25 x 3 mm - Bending angle left + right selectable - Hydr. Double-sided bending function - Hydr. Delivery ° - Drive 400 V / 11 kW - Space requirement approx. W 1750 x H 2200 x D 2300 mm - Weight approx. 1600 kg - with - bending angle adjustment - Hydr. Voltage - Bending tools

Key data: 200 mm, 400 , 360

Profile Bending machine Model AR360 -Year 2004 MG brand made in Italy OUTPUT SHAFTS 360 MM Capacity as per the original bending chart here enclosed Configuration installed with the machine -Pyramid dual pinch side rolls independent hydraulic positioning bending and pre-bending performance -The 3 shafts driven with hydraulic motor and gear unit individual on each roll -Synchronized speed automatic hydraulic control between the 3 rotating shafts -hydraulic traction tool to roll HEB_INP_UPN bending on hard-side. -Lateral correctors left/right hydraulic operated in 3 directions Tooling with the machine -Set of rollers for pipe: 6” and 12” -Set of rollers with adjustable opening width up to 400 mm ( for all the profiles bending easy way and hard way ) -Set of rings to increase the rollers opening width up to 500 mm ( for all the symmetric profiles b ...

Key data: 200 mm, 300 , 200

Profile bending roll used equipment hydraulic model AR200 year 2008 make MG Italy Capacity bending chart photo in enclosed -Technical data: Output shafts size 200 mm -Machine complete with set of rollers adjustable for the various shape of profiles. -Traction tool hydraulic operated for the HEB-beam - IPE - UNP bending the hard side. -Lateral correctors left and right side hydraulic operated in 3 direction. -Included additional set of rolls for pipe 6" inches -Machine with 3 rolls driven system with individual hydraulic motor and axial gear-unit on each shaft. -The 3 shafts working on bearings, heavy duty type with sealed lubrication. -Centralized control panel movable on wheels with all electric commands. -Dual rolling speed up to 5 mtr/min with automatic balancing system between the 3 rolls. -Safety devices in compliance with European regulation. CE mark. - ...

GM-SB-38CNC-2A1S tube bending machine was built in 2019 in China by ZHANGJIAGANG KING-MACC MACHINERY MANUFACTURING CO., LTD. The machine, distinguished by its high precision and ease of operation, is used for bending tubes and profiles with a maximum diameter of 38 mm. All process parameters, including even the most complex shapes, are programmed in an intuitive PLC controller with memory for up to 200 work programmes. Thanks to the high degree of automation, the offered GM-SB-38CNC mandrel bending machine is an indispensable tool in any production facility. The total weight of the machine is approximately 1500 kg. Technical specifications of the GM-SB-38CNC-2A1S tube and profile bending machine - operator panel with PLC controller - bending capacity: ⌀ 38×2 mm - maximum bending angle: 180° - maximum bending radius: 200 mm - minimum bending radius: 20 mm - mandrel length: 32 ...

MEP Multimatic SA8, year of construction 1995 Straightening and cutting system for reinforcing steel, fully automatic, complete functional system, immediately available Plant still in operation and can be demonstrated.