cnc lathe 4 used for sale

Type: Welding equipment set (MIG/MAG) Manufacturer: Lincoln Electric Main unit: CV 450 T Wire feeder: LN 442 Cooling unit: COOL ARC 25 CE Marked: Yes Power supply: 400 V / 3~ / 50-60 Hz Protection class: IP21 Welding output: 50 A / 16 V - 450 A / 36 V Duty cycle: 35% / 60% / 100% Control range: Adjustable voltage and wire feed settings Included: - Lincoln Electric CV 450 T power source - LN 442 wire feeder - COOL ARC 25 cooling unit - Cables and hoses as photographed Condition: Fully functional Remarks: Used machine set with normal signs of wear; can be inspected on site; see photos for overall condition Auction-ID: A7-47063-13

Robotic lawnmower AM 430X incl. charging station; Device serves as spare parts carrier #224407357 Auction-ID: A7-47086-232

Schaffer Equipped with double working hydraulic circuit Hydraulic quick coupler Battery key Front / rear / arm - led work lamps Rear plug for trailer Rear tyres filled with glycol Well maintained ! Auction-ID: A3-43539-19216

Type: LPG forklift truck (counterbalance) Manufacturer: Jungheinrich Model: FG 425 (as per plate) Serial number: FN382800 CE Marked: Yes Load capacity: 2,500 kg @ 500 mm load center Mast type: Triplex mast with sideshift Lifting height: approx. 3,300 mm Lowered mast height (h1): 2,500 mm Extended mast height (h4): 4,051 mm Tilt angle: 6° / 8° Fork dimensions: 40 x 120 x 1,150 mm Fork carriage width: 1,120 mm Turning radius: 2,285 mm Overall length: 3,763 mm Length to fork face (l2): 2,613 mm Overall width: 1,184 mm Wheelbase: 1,750 mm Drive: Hydrostatic transmission Fuel type: LPG (gas) Engine: VW / BEF, 4-cylinder, 1,980 cm³ Engine power: 38 kW Rated speed: 2,700 rpm Hydraulic system: - Working pressure: 215 bar - Oil flow: 32 l/min Operating weight: approx. 3,960 kg Noise level: 75 dB(A) Cab: Enclosed operator cabi ...

• Porsche-Diesel Master 419 \"long version\" vintage tractor • Rare long version – significantly rarer than standard model • Year of manufacture / first registration: 01.07.1962 • Original Porsche diesel farm tractor • 37 kW / approx. 50 hp diesel engine • 3,500 cc displacement • Chassis number: 419456 • Approved as LOF. Farm tractors • German vehicle documents available • DEKRA documents available • Highly sought-after collector's and enthusiast's version • Long version with longer wheelbase and striking look • Only comparatively small numbers of the long-wheelbase version were built • Particularly interesting for collectors, Porsche diesel enthusiasts and classic car exhibitions • Restored and very well maintained overall condition • Eye-catching red paintwork with very good presentation effect • Nameplate available and legible • V ...

Extra options : All-round lighting , Fingertip control , Blue spot , Rotating beacon , Auction-ID: A1-43891-26

3 double acting rear valves Air brakes 650/65R42 and 540/65R30 BKT tires Full LED work light PDF 540/540/1000/1000€ Front linkage Auction-ID: A3-43539-39057

Bystronic BTL 4000 – Laser Resonator Cabinet Manufacturer: Bystronic Laser AG (Switzerland) Model: BTL 4000 Year of manufacture: 2000 (according to nameplate) Laser medium: CO₂ Wavelength: 10,600 nm Max. CW power: 4,200 W Peak power: 7,000 W Pulse range: 150–25,000 µs Frequency: 1–2,500 Hz Standard: EN 60825-1 Scope of delivery: Resonator cabinet only – exactly as shown in photos. Not included: Turbine / blower unit and other missing components. Approx. weight (nameplate): 1,400 kg Auction-ID: A7-47063-9

Fully equipped SAME Golden 65 Compatto 4x4 compact narrow-track tractor with cab, 3-cylinder 3.0-litre turbo engine, front hydraulics, front and rear PTO, rear lift and extensive hydraulic equipment. The tractor was extensively rebuilt from 2018 onwards: rust-prone fender and cab parts were replaced in stainless steel, the cab was dismantled and the tractor was painted in RAL 9005 deep black silk matt with corrosion-preventing PU paint. Battery replaced, engine starts reliably and runs cleanly. Extensive operating, workshop and spare parts documents as well as maintenance and repair documentation available. A total of 8 wheels/rims are included in the scope of delivery. Equipment: · 4x4 all-wheel drive, front and rear differential lock · 3-speed powershift, 5-speed manual transmission, 3 groups and reverse gear · Front linkage 950 kg and rear linkage 1,800 kg · Front and rear P ...

Robotic lawnmower AM 405X incl. charging station; Device serves as a spare parts carrier #234970285 Auction-ID: A7-47086-225

Zoller Tool Presettler Smile 400 A Zoller tool presetter is an external measuring machine that allows you to capture the geometry data of your CNC tools (such as length, diameter and radius) outside the machine tool. This saves set-up time, increases precision and extends tool life. Zoller »smile« / »smileCompact«: The ideal standard device for the workshop. It is compact, easy to use. For sale is a fully functional Zoller tool presetter of type [model, e.g. Smile 400]. The device is characterized by the highest precision and intuitive operation. Ideal for CNC milling and turning operations to reduce set-up times. [1]oh and provides basic measurement functions for length and diameter SK 50 mounting,

Equipped with Rated input voltage: 3P AC380V ±15% 50/60Hz; Rated duty cycle: 40%; Efficiency: 85%; Insulation class: F; Protection class: IP21; MIG: Rated input power: 13.8 kVA; Rated input current: 21A; Open circuit voltage 80V; Output current 40-350A; Output voltage 31.5V; TIG: Rated input power: 10.5 kVA; Rated input current: 16A; Open circuit voltage 80V; Output current 10-350A ; Output voltage 24V: MMA: Rated input power: 11.8 kVA; Rated input current: 18A; Open circuit voltage 80V; Output current 30-300A; Output voltage 32V; Power current 0-99A; Ignition current 0-99A; including all accessories; Unused in box

Universal Tool Milling Machine Manufacturer: AVIA S.A., Poland Type / Model: FNE 40 P Year of Make: 2013 Serial Number: 90567 Accessories / Scope of Delivery • Machine Vise • Tool Holders SK40 • Various Milling Tools and Clamping Devices • Documentation / Documents   Dimensions (L × W × H): approx. 195 × 220 × 220 cm Weight: approx. 1,900 kg Table / clamping surface: • Clamping surface: approx. 800 × 400 mm • T-slot table • Max. table load: approx. 400 kg Travel paths / machining range: • X-axis: approx. 620 mm • Y-axis: approx. 420 mm • Z-axis: approx. 400 mm Spindle: • Spindle holder: SK 40 (DIN 69871) • Max. spindle speed: 4,000 rpm • Speed range: approx. 50 – 4,000 rpm, infinitely variable • Max. tool diameter: 125 mm • Max. tool weight: 6 kg Feeds: • Stepless feeds in X / Y / Z • Working feed up to approx. 2,000 mm/min • Rapi ...

Set of 7 Pro-face GP-4301TW Human Machine Interfaces (HMI) Description: We offer for sale a set of 7 Pro-face industrial operator consoles mounted in a box, used in an industrial environment. These GP-4301TW Pro-face touch HMI interfaces are recognized for their reliability and ease of integration into automation systems (special machines, production lines, machine tool retrofits, etc.). The consoles are pre-installed in industrial enclosures with cable glands and wiring, making them easy to reuse or integrate into a new installation. Main features: Brand: Pro-face (Digital Electronics Corporation) Model: GP-4301TW Reference: PFXGP4301TADW Type: Touchscreen Human Machine Interface (HMI) Technical characteristics: Color touchscreen Power supply: 24 VDC Power consumption: 0.43 A Max temperature: 50°C Industrial communication via Ethernet/serial port Protection: IP suitable for lecte ...

NEW, width: 1.76 m, 590 kg net weight, 460 l capacity, 245 max. bar, with original Kramer 5075 mount, with 1/2 quick coupling set & hoses, electrical kit for doubling the hydraulic circuit

Technical data: Turning diameter over bed: 1260 mm Turning diameter at opening: 2700 mm Turning diameter at the pit: 3800 mm Turning diameter via slide: 900 mm Turning length: 4000/5000 mm

Technical data: Diameter over bed: 625 mm Turning length: 1500 mm Diameter via slide: 325 mm Spindle head shape: Cam-Lock Spindle drilling diameter: 105 mm

Technical data: The machine is completely overhauled in 2011 with new electrics, new wiring, including new control SIEMENS Sinumerik 840D max. circulating and turning diameter: 2,000 mm max. turning height: 1,500 mm Sheet disc diameter: 1,600 mm max. table load: 11.20 to. Cross-beam adjustment: 1,170 mm

Control Siemens

CNC Control Traub System TX 8D C-axis/ Driven tools Bar feeder Stamag DN42 Collector of the finished parts Chip conveyor Internal liquid cooling Very good condition Max. bar diameter 42 mm Turning length 220 mm Hydraulic chuck Chuck- max. turning dia. 140 mm Max. turning diameter 140 mm Max. turning diameter over bed 390 mm Spindle boring 42 mm Number of turret heads- 3 -1st turret 12 tools -2nd turret 12 tools -3rd turret 4 tool Tool holders VDI 30 X axis travel 200 mm Z axis travel 300 mm Spindle speed 5600 rpm Max. bar length 4200 mm Max. working bars in dia. 42- 7 Total power requirement 34 kW Interlocking cover Total dimensions: 7400x1900x2400 mm Weight 4500 kg

CNC carousel lathe with tool changer.You Ji GTH-35/45 ATC-I. Built 2012.Fanuc 0i-TD CNC Control.Planchime diameter 3,500 mm.Hydrostatic table - Max load 50 t.swing diameter max. 4,500 mm.Turning diameter max. 4,000 mm.turning height max. 2,200 mm.Stoesselplanweg X -1.750/+2.160 mm.Stoesselsenkrechtweg Z 1.500 mm.Table drive 60/75 kW.Speed 2 x 75 mm.Torque at the table 67,330 Nm.Tool magazine with 16 places.Tool holder 7/24 BT 60.Place requirement 12,375 x 8,210 mm.Machine height 7,920 mm.Full cladding.3-colors Signal lamp.NEW - 200 operating hours ! Immediately available;; As good as new

CNC Vertical Lathe VTL with Tool Changer.You Ji GTH-35/45 ATC-I.Year of manufacture 2012.Fanuc 0i-TD CNC Control.Face plate diameter 3500 mm.Hydrostatic table - Load max. 50 t.Swing diameter max. 4500 mm.Turning diameter max. 4000 mm.Turning height max. 2200 mm.Ram cross travel X -1750/+2160 mm.Ram vertical travel Z 1500 mm.Table drive 60/75 KW.Table turning speeds 2 ~ 75 mm.Torque at the table 67330 Nm.Tool magazine with 16 positions.Tool taper 7/24 BT 60.Floor space required 12375 x 8210 mm.Machine height 7920 mm.Full guarding.3-colour signal lamp (tower).AS NEW - 200 run hours !Available immediately.; As new

Turning Diameter 400 mm Turning Lenght 650 mm With C ,Y axes and subspindle Control Unit Fanuc 31i Can be inspected under power

Table diameter: 2,000 mm Max diameter of workpiece: 3,000 mm Main drive: 60 KW Speed rotation of the table: 2.8 - 162 rpm Max workpiece height under the cross member: 2,500 mm Travel RAM: 1,750 mm Tool magazine: 12 workstations Machine Weight: 35 t Accessories: Grinding spindle and various tool holders 3000 rpm Wheel diameter 250 mm

: 0554 mm : 2000 mm : : 277 mm : 104 mm : 400 mm : 2000 U/min : D1-11 DIN 55029 : 95 mm : 145 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 300 mm turning length: 1500 mm control: FanucSystem 6 T total power requirement: kW weight of the machine ca.: 5 t dimensions of the machine ca.: 4x2x1,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 720 mm turning length: 2250 mm control: CNCN 300 turning diameter over bed slide: 480 mm 3-jaw-chuck diameter: 650 mm total power requirement: 44 kW weight of the machine ca.: t dimensions of the machine ca.: m Voltage 380VHertz 503-jaw chuck ø (mm) 650 Including: Turret, 9 positionChip conveyor The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 800 mm turning length: 4000 mm control: cnc total power requirement: kW weight of the machine ca.: 7,3 t dimensions of the machine ca.: 6,6x2,2x2 m Brand: Phoenix Type: FL 8040 CNC IT Year of make: 2001 Distance between centers: 4.000 mm Centre height: 400 mm Swing over bed: 800 mm ø Swing over support: 510 mm ø Swing in the gap: 1.100 mm ø Spindle boring: 250 mm ø Steady rest: 350 mm ø 3-Jaw chuck: 630 mm ø Machine dimensions (lxwxh): 6.500 x 2.200 x 2.000 mm Machine weight: 7.300 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

2012 Muratec MW 120 GT Metal 2012 Muratec MW 120 GT and more: Mori Seiki ZT 1500YB in operation, can be viewed during operation. 2002 yes Mori CL 2000 can be viewed under power. Currently not in operation 2004 yes Mori Seiki SL-204 can be viewed under power. Currently not in operation 2001 yes Mori Seiki SL-204 can be viewed under power. Currently not in operation 2003 yes Tsugami NP-32 can be viewed under power. Currently not in operation 1992 yes Riello in operation, can be viewed during operation. 2002 yes

Machining diameter max: 36 mm Maximum spindle speed: 6300 rpm No. of Spindles: 2 Controller: Traub TX8i Toolchanger 1: No. of tools: 12 positions X-axis travel: 50 mm Z-axis travel: 50 mm Toolchanger fronside: No. of tools: 7 positions Speeds: 150 - 3000 Rpm 300 - 6000 Rpm Max. diameter: 40 mm X-axis travel: 370 mm Z-axis travel: 250 mm Toolchanger backside: No. of tools: 5 Speeds: 150 - 3000 Rpm 300 - 6000 Rpm Max. diameter: 40 mm X-axis travel: 73 mm Barfeeder: FMB Turbo 5-42 Barlength: 3200 mm Bardiameter: 5 - 42 mm Country of origin: Germany Machine LxWxH: 3400 x 1300 x 1700 mm Machine weight: 4000 kg

SPINNER TTC 300- 52 SMMCY CNC Lathe YOM 2012 Twin-opposed-spindle, twin-turret lathe Control FANUC 31iT Swing diameter 400 mm Max. turning dia ~200-250 mm Max. turning length 400 mm Travels: X1 180 mm, X2 110 mm, Z 450 mm, Y +40/-40 mm Rapid traverse: X1 15 m/min, X2 15 m/min, Z 24 m/min, Y 15 m/min With C-axis Main Spindle 1: Motor spindle with water cooling With hollow shaft measuring system for C-axis drive mounted directly on the spindle shaft Spindle bore 52 mm Spindle speed 0-5000 rpm/ 19 kW Performance Pmax 23,5 kW Torque 150 Nm Spindle nose A6/DIN Sub-Spindle 2: Motor spindle with water cooling With hollow shaft measuring system for C-axis drive mounted directly on the spindle shaft Can be moved on a slide to take over spindle 1 Spindle speed 0-7000 rpm/ 8 kW Performance Pmax 13,8 kW Torque 189 Nm Spindle nose 100 mm Turret 1: At the top of the ...

Ref. -No.: 10367 Manufacturer: WEILER Year of construction: 1996 Type of control: CNC Control: Siemens Storage location: Halberstadt Country of origin: Germany Turning Speeds: 500 RPM Machine length: 7000 mm Machine width: 2300 mm Machine Height: 2600 mm Weight Of The Machine Ca.: 9,25 t Spindle Taper: 6 Mk Travel quill: 300 mm Bed width: 800 mm Turning Length: 3000 mm Turning Diameter Over Bed: 900 mm Swing Diameter Over Bed Slide: 530 mm Spindle Bore: 254 mm Spindle power: 45 kW Tailstock - Insertione Into The Sleeve: 140 Ø Max. Workpiece Weight: 5000 kg Further information: Machine can be inspected under power.

Ref. -No.: 10364 Manufacturer: MAZAK Year of construction: 1997 Type of control: CNC Control: MAZATROL T PLUS Storage location: Halberstadt Country of origin: Japan Machine length: 6365 mm Machine width: 3180 mm Machine Height: 2800 mm Weight Of The Machine Ca.: 7 t Bar passage: 64 mm Max rotation diameter: 510 mm Turning Diameter: 400 mm Turning Length: 1539 mm Spindle power: 22-26 kW Spindle Speed Min.: 35 RPM Spindle Speed Max.: 3500 RPM Rapid Travel Speed X-Axis: 12 m / min Rapid Travel Speed Y-Axis: 10 m / min Rapid Travel Speed Z-Axis: 18 m / min Motor power milling spindle: 7,5 kW Max. speed milling head: 15-6000 RPM X-axis travel: 450 mm Y-axis travel: +/- 90 mm Z-axis travel: 1539 mm Number of tools in the chain magazine: 40 (15 + 25) POS Further information: The main spindle was replaced with a new one in Oktober 2019. In the course of this, small spare parts were renewed or r ...

Ref. -No.: 10294 Manufacturer: SCHNEIDER WERKZEUGMASCHINEN Year of construction: 1983 Type of control: CNC Control: Siemens Sinumerik 840 D Storage location: Halberstadt Country of origin: Deutschland Machine-No.: 27.0175 Weight Of The Machine Ca.: 4 t Turret places: 8 Pcs Turning Diameter: 595 mm Turning Length: 3000 mm Bezel diameter (inside): 240 - 490 mm Further information: Tool turret, with 8 holders, with chip conveyor, approx. 300 mm wide, Belt filter system Mayfran, 2 bezels, 1 x for diam. up to 240 mm, 1 x for diam. until about 490 mm

Ref. -No.: 10036 Manufacturer: JOHNFORD Year of construction: 2009 Type of control: CNC Control: Fanuc Series 18i-TB Storage location: Halberstadt Country of origin: Taiwan Machine length: 9800 mm Machine width: 3695 mm Machine Height: 5292 mm Weight Of The Machine Ca.: 32,6 t amount of positions: 12 Bar passage: 165 mm Serial no.: TDF9007 Turning Length: 2000 mm Turning Diameter Over Bed: 1550 mm Swing Diameter Over Bed Slide: 1270 mm Longitudinal Travel (Z-Axis): 2000 mm Spindle Head: A2-15 Spindle Diameter In Front Bearing: 240 mm Spindle Bore: 185 mm Spindle power: 37/30 kW Cross Travel: 685 mm Spindle Speeds: 1000 RPM Rapid Travel Speed X-Axis: 10 m / min Rapid Travel Speed Z-Axis: 12 m / min Tool changer: 12 Pcs

Multi-spindle lathe (8 spindles) max. rod diameter 16 mm Guide tubes 4,000 mm Conveyor

Stock number: 3739 CNC LATHE Manufacturer: RIKA, Type: D 8004-2 Machines NO.: 622160, Year of manufacture: 1999 Specifications: Max. circumferential diameter 240 mm dia. Turning length 350 mm Main motor power 5 kw Spindle bore 40 mm dia. C axis - main spindle movement 360 degrees Z ash movement 170 mm Z 2 Axis Movement 782 mm Tool turret 1 with 12 stations Tool turret 2 with 12 stations Sub-spindle Accessories: Hydr. Chuck main spindle mm dia Hydr. Chuck Subspindle mm dia Chip conveyance. Cooling water system. Length: 1600 mm, Height: 2100 mm, Width: 3100 mm, Weight: 2000 kg

WE OFFER AN NICE CONDITION TWO MACHINES EMCO HYPERTURN 665 WITH BARR FEDERS AND TOOLS ACCESSORIESS YEAR: 2005 FULLY FUNCTIONAL , READY TO WORK CONNECTED ON POWER. FOR THE CUSTOMER WE ORGANIZE DISMANTLING LOADING AND TRANSPORT TECHNICAL DATA: Specifications: Max. swing diameter 430 mm dia. Max. rotary. About Bed 600 mm Dia. Turning length 744 mm Distance between spindle lugs 975 mm Main engine power 21/29 kw Main spindle speed range 0-5000 rpm Bore through drawing tube 65 mm dia. C axis - main spindle movement 0.001 degree Y axis 100 +/- 50 mm B Axis Movement Stepless 45 Degree Tool turret 1 with 12 VDI 30 stations Powered stations turret 1 12 pc. - 4000 rpm Y+B pieces. Engine power driven tools 6.7 Kw Tool turret 2 with 12 pc. VDI 30 stations Counter spindle C axis - counter pindel movement 0.001 degree Counter spindle speeds 0-5000 D46485 Pr/mi ...

turning diameter: max 300 mm turning length: max. 2000 mm control: Siemens Serie 810D turning spindle: Durchlass 90 mm : 300 mm Feed speed: 6/6 m/min. number of tools: 8 quill stroke: 300 mm diameter of quill: 105 mm taper MK: 6 coolant tank: 100 l total power requirement: 15 kW weight of the machine ca.: 4650 KG dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stock number: 3919 CNC LATHE Manufacturer: MAZAK, Type: HQR 200 MSY Year of manufacture: 2018 Specifications: Max. circumferential diameter 344 mm dia. Turning length 860 mm Main motor power 22 kw Main spindle speed range 5000 rpm Hole through drawing tube 65 mm dia. C Axles 0.001 Both spindles Y axis upper 100mm / lower 70mm mm Tool turret 1 with 12 stations Tool turret 2 with 12 stations Powered tools. 6000 Both Turrets rpm Control Mazak Smooth Fabr. Accessories: Collet device. Heinbuch 65 both spindles Hydr. Chuck main spindle 210 mm dia Hydr. Chuck Subspindle 210 mm dia Driving angle tools 6 pieces Driving Tools Straight 5 pcs. Tool setter Charging Hydrafeed X-Tract Delivery time September 2024 Length: 4000 mm, Height: 2500 mm, Width: 2700 mm, Weight: 12500 kg

Control: Siemens 840 D powerline Accessories: Tool holder bar loading magazine Fully functional and still under power, can be visited at any time