127,294 used machines on RESALE, but how to find them? Machine Search
; Power [PS]: 598; Gross weight [kg]: 7885; Engine: Cat C18; Accessories: Tanker, Battery, Control Panel, Stahldach, - Built in switch 50/60 Hz; Water Tank Volume [l]: 1125
Shredder mill with blades brand: Trit, Model: TRIT-510, motor: 10 hp, new, cutting chamber: 330 x 250mm, with electrical panel.
x-travel: 4300 mm y-travel: 1000 mm z-travel: 1050 mm total power requirement: kW weight of the machine ca.: 35 t dimensions of the machine ca.: m Brand: ANAYAK Type: HVM-5000 Build in : 1997 CNC Control HEIDEHAIN, TNC 426 Tablesize: 5000 x 1000 mm X= 4.300 mm Y= 1.200 mm Z= 1.050 mm Toolchanger for 40 tools Tools: BT 50 CNC Controlled head 2,5 degrees Cooling trough the spindle Number of controlles axes: 4 machineweight 35.000 kg Moveable column The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter: 1040/1900 mm turning length: 2000/3000/1250 mm swing diameter over bed slide: 740 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Make: EST-Ticino type: 520/2000 distance between centers min/max: 2000/3000 mm center height 520 mm Max. turning diameter over bed 1040 mm Max. turning diameter over support 710 mm max. turning diameter/length 1900 x 1250 mm spindle passage 135 mm with 3 jaw chuck with 4-jaw chuck quick change holder in very good and immediately ready condition The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
The power plant, based on a 5 MW gas turbine CENTRAX 501 KB7 is complete with all needed equipment, allowing a steam output of 20 tons per hour at 20 bar. From ZERO hours until the last working day all maintenance was performed by Centrax under full maintenance contract.
Mondini Tray Sealer High speed, twin lane tray sealer 4 across tool Has been used for packing ground meat in MAP trays.
; Gross weight [kg]: 2924; Engine: Caterpillar C13; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 721
; Gross weight [kg]: 3886; Engine: Caterpillar C13; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 721
EU STAGE 5 Compliant, 50/60 Hz switchable frequency via terminal link, 550 kVA Prime power, Spark arresting silencer; Gross weight [kg]: 6740; Engine: Perkins 2806J-E18TAG1; Accessories: Tanker, Battery, Control Panel, Stahldach, Including sockets CEE-Form:, 2x 16A (1ph+N+E), 2x 32A (3ph+N+E), 1x 63A (3ph+N+E), 1x 125A (3ph+N+E); Water Tank Volume [l]: 1125
; Gross weight [kg]: 18290; Engine: Caterpillar 3516B HD; Accessories: Control Panel, Caterpillar 3516B HD Genset from the official CAT Rebuild Program., Engine is completely rebuild by CAT or even unused/surplus., All other components are usually new., Comes with the standard CAT factory warranty.
Travel distances: 500 x 450 x 400 mm [ X x Y x Z ] Number of axles: 5 Rotary swivel table HEM 500 U 3+2 Control: Heidenhain iTNC 530 Spindle holder: ISO 40 / BT 40 Spindle speed: 12000 rpm Tool changer: 30 - fold Drive power : 20 kW Torque : 75 Nm Rapid traverse: 30 m/min Spindle cooling Conveyor Diameter 500 mm IKZ 20 bar ITC 5X Intelligent Thermal Control Oil trap Minimum quantity lubrication Oil mist extraction Blowing air through tool screw Mobile handwheel Glass scales Encoder B-axis Encoder C-axis Tool probing system (TS27R OMP40 Probe
Complete laundry for PET, PVC or PS in stainless for some: 500 Kg / hour. Composed of: -Reception and densing raft: 1,500 mm x 500 mm, with two blades. -Collection and stirring pond: 1,500 mm x 1,500 mm. With emptying valve and outlet belt to centrifuge of canjillions. -Centrifuge: 3,000 r.p.m., 12.5 c.v. -Collection and shipment of centrifuge to chamber separation of paper and thin. -System by air extraction separation of papers. -Collection and shipment to cyclone for Big-Bag filling.
; Gross weight [kg]: 13000; Engine: DC13 072A/02-12; Accessories: Tanker, Battery, Control Panel, Stahldach, -Super Silent Canopy; Water Tank Volume [l]: 2500
Machine Details Stock number 1105-03824 Machine type machining center - vertical Make CINCINNATI Type SABRE 500 Year of construction 1995 Control type CNC Storage location HAGUEANU FRANCE Country of origin Great Britain Delivery time immediately Freight base AB HAGUENAU FRANCE Technical details x-travel 500 mm y-travel 510 mm z-travel 510 mm Table size 950 x 520 mm Spindle holder ISO 40 Spindle speeds 60 - 6000 rpm Spindle drive motor 5.5 kW Rapid traverse 24 m/min Tool changing device 21-fold CNC control HEIDENHAIN TNC 415 Operating voltage 380 V table load 750 kg Projection 550 mm Total power requirement 30 kVA Machine weight ca. 4 t Information - Control: HEIDENHAIN 415 - Coolant device - Machine light
Automatic Transfer Switch - ATS Panel - ATI Panel, 2.500 Ampere - Applicable for generators up to 1.730 kVA; Gross weight [kg]: 311
Edge banding machine Cehisa SYS 5PS - Only about 60 km edges glued / little used! - Condition tiptop - Sturdy construction all important aggregates available: - Infeed ruler - Joining milling - Preheat plate - Glue application - Apply edges (rolls or strip magazine) - Pneumatic pressure roller driven - Pressure roller on top, spring-loaded - Pressure roller at the bottom, spring-loaded - Caps front & rear - Flush milling top and bottom - Copy corners front and back -Scraper - Schwabbelscheibe Accessories: -Tool - Feed rollers for various edge materials - various spare blades - Settings folder Year of construction 2008 Masch. No. 532 The machine is approx. Available at the beginning of October (probably earlier) and would then have to be picked up on a fixed date. Disassembly and collection by buyers The machine is in top condition, ready for ...
Machine Details Stock number 1105-03832 Machine type machining center - vertical Make CINCINNATI Type SABRE 500 Year of construction 1995 Control type CNC Storage location FRANCE Country of origin Great Britain Delivery time immediately Freight base EX LOCATION HAGUENAU Technical details x-travel 500 mm y-travel 510 mm z-travel 510 mm Table size 950 x 520 mm Spindle holder ISO 40 Spindle speeds 60 - 6000 rpm Rapid traverse 24 m/min Spindle drive motor 5.5 kW Tool changing device 21-fold CNC control FANUC OM Operating voltage 380 V table load 750 kg Projection 550 mm Total power requirement 30 kVA Machine weight ca. 4 t Information - Control: HEIDENHAIN 415 - Coolant device - Machine light
Brake ring conical, 9v 532KB160, Demag, new Special offer! If you have a VAT number, we will be happy to issue you with an invoice without VAT. As good as new! The part comes from the spare parts warehouse of a certified manufacturing company, has never been used and is in mint condition. 6 months warranty We give you 6 months warranty for these goods from the date of invoice. In case of any defect, which is not the fault of the buyer, the goods can be returned. We will refund the buyer only the product price paid to us. Updating in case of digital components is excluded. Also excluded is liability for direct and indirect consequential damages. Our terms and conditions apply, see our website. Austrian law applies without exception and court location St. Pölten.
DIGI SM-5500B System Scale SM-5500B, the advanced PC-based system scale printer that provides you with multiple retail solutions. Increases operating revenue, improves operations with integrated queuing and collection system through various innovative features of the SM-5500B. Experience real retail solutions offered by DIGI's PC scales. • Linerless printing with integrated automatic cutting device • Watermark printing • Speed ID • InfoTag and electronic signage e.Label • Integrated queuing and collection system •Waste management • Interactive screen display Power source 230 V (50/60 Hz.) Operating Humidity 15% - 85% RH Non-condensing Operating temperature -10° C to +40° C Operator display 12.1" Customer Display 7"WVGA (800x480) Interface RS232C, Ethernet (standard) max. 15/30 kg, min. 100g, e = 5/10g, Dimensions (in mm) 385(W) x 507(D) x 148(H) ...
Nominal mass of falling parts, taking into account the mass of the upper stamp (500 kg.), Kg. 5000 Actual mass of falling parts without top stamp, kg. 5030 Effective kinetic energy of falling parts at full successive impacts, kgc m 12500 The greatest working stroke of a woman, mm. 1300 The smallest height of dies without shanks, mm. 400 Distance between guides in the light, mm. 800 The length of the woman in the direction perpendicular to the front of the hammer, mm. 1180 Steam (air) pressure before entering the cylinder, atm. 7-9 Nominal mass of the upper die, kg 500 The largest mass of the upper die, kg. 1500 The highest permissible steam temperature, ⁰C 200 weight 145-148ton, weight of anvil block 75+22 ton.
technical details: - Volume flow (V): 8,000 m3/h - Shaft power (Pw): 18.5 kW - Shaft speed (nw): 2717 rpm - Diameter intake manifold (suction side): 360 mm - Dimensions outlet opening (pressure side): 400 x 255 mm (inside), 48 x 335 mm (outside) Engine: - Power: 22 kW - Characteristics: 400 V / 37.5 A / 50 Hz - see engine plate (photo) Dimensions (W x H x D): 1,300 x 1,100 x 1,550 mm The fan has been electrically and mechanically tested and partly repainted! (Changes and errors regarding technical data and prices excepted!) In accordance with our terms and conditions, we would like to point out once again that cheques and bills of exchange cannot be accepted.
Vertical mixing silo. Approximate capacity 56 m3, dimensions Ø3.590x8.370 mm of total height. Made of steel S-235 and built in sheet thickness 3 mm with perimeter rings of reinforcement UPN-80, support structure by means of 4 pillars HEA180 mm braced with HEA-120 profiles, inner thread of Ø300 mm, step 200 mm with shaft tube of 114.3x6.02 mm placed in tube-jacket of Ø 355x4,78 mm, registration on the side for visit and inspection and in the lower tube for emptying in case of jamming or breakdown, equipped with safety system, 4 inspection sights, two upper ventilation vents, maximum level indicator FILSA type MS-1, transmission by pulleys and belts with 22 kW motor at 1,000 rpm with safety protections, discharge pipe 200x200 mm connected to inner screw jacket of mixer with manual closure at the outlet mouth, Nozzle at the bottom of cone for complete emptying of machine, cat ladder with ...
2 LORIS BELLINI high temp high temperature vertical cone/bobbin dyeing machine type RBNV 550/975, year 2001 and 1989, capacity each 20 Kg, autoclave diameter 550 mm, The 2 machines are delivered with total 2 bobbin carriers with 4 swords each, each word has a useful loading height 975 mm, add vessel on each machine, the 2 machines share the same electrical cabinet which was supplied by LORIS BELLINI in 2001
Refer to code 1024 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.
Dimensions (L/W/H): 1750x1100x1640 mm Weight: 1000 kg Total power requirement: 15 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 6900x1750x1660 mm Weight: 450 kg Total power requirement: 4,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Refer to code 1026 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.
Dimensions (L/W/H): 6000x1150x2980 mm Weight: 800 kg Total power requirement: 3 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 1950x690x1700 mm Weight: 431 kg Total power requirement: 7,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 1070x495x895 mm Weight: 80 kg Total power requirement: 3 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 800x700x500 mm Weight: 100 kg Total power requirement: 0,25 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Refer to code 1028 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.
Dimensions (L/W/H): 9850x2300x1770 mm Weight: 3480 kg Total power requirement: 14 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 7300x1600x2600 mm Weight: 5500 kg Total power requirement: 0 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 0x0x0 mm Weight: 1000 kg Total power requirement: 8,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Refer to code 1032 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.
8 Color Stack UV Flexo Printing Machine Overhauled 2020 with installation IST MBS 7 UV system in 2020. Substrates: OPP,BOPP,PET,PVC,OPS,paper,aluminium foil. Print width max 560 mm, Material width max 580 mm 8 flexo printing units Speed 200 m/min, Camera (E+L) Register control (E + L
max. format 36.50 x 52 cm Year of construction: 1998 Shed feeder Ryobi Filmfechtwerk SuperDampener Cooling unit MGE ECO Plate quick-release rails Dry pollinators Delivery date: immediately Price on request. We deliver and install worldwide!
Dimensions (L/W/H): 6000x1150x2980 mm Weight: 850 kg Total power requirement: 3 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 5000 m³/h power capacity: 5,5 kW Speed: 3000 U/min. : 280 mm Dimensions (L/W/H): 2460x1250x1600 mm Weight: 380 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Precision Deburring Faceting Milling Machine / Edge Milling Machine Specifications: Steel – stainless steel – aluminium – plastic – machining Deburring and faceting process is carried out with milling cutter Support angle - facet angle tiltable Facet angle adjustment 15 to 45 ° Facet width infinitely adjustable 0 to 7 mm Length of guide strip 500 mm Speed 2750 rpm Drive 400 V / 0.7 kW Space requirement approx. W 650 x D 600 x H 950 mm Weight approx. 30 kg
Dimensions (L/W/H): 920x2100x2150 mm Weight: 300 kg Total power requirement: 5,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 1950x690x1700 mm Weight: 426 kg Total power requirement: 5,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Arburg 520C-2000-800 (193) Description with conveyor belt, bimetallic screw General Information SKU: 193 Availability: In stock Year of construction: 2005 Brand: Arburg Specifications Injection weight: 434 g Clamping force: 2,000 kN Screw diameter: 55 mm Spray pressure: 1650 bar Tie bar spacing: 520x520 mm Clamping plate size: 728x728 mm Tool installation height min.: 250 mm Control: Selogica Language: German Power: 44.9 kW Operating hours: 80000 h Weight: 7300 kg Dimensions: 6x2 m Funnel: No Core train: Yes Euromap: Yes
Chassis number 50145 Year of construction 1991 Voltage 380V / Freq 50 Hz An automatic cutting table specifically designed for cutting laminated glass (with PVB or EVA). Below you'll find the key specifications and features. Technical specifications Machine type: Automatic cutting table for laminated glass (PVB/EVA) Maximum glass size: approx. 3300 mm Processable thicknesses: from 3+3 mm to 10+10 mm Cutting head: CNC controlled Automatic pressure adjustment depending on glass thickness Simultaneous cutting of both glass layers Breaking system: Breaking bar for mechanical breaking Thermal separation via linear resistance (heating element) Cutting accuracy: ± 0.3 mm Work surface: air cushion table (air float) for easy glass transport Control & programming: Input of cutting formats and patterns Possibility to upload files (CNC programs) Machine dimensions: approx. 36 ...
maximum number of results exceeded
please refine your search
