cm used for sale

Replacement diaphragm SAMSON 520-0976 Diaphragm 700 cm² New ! Dimensions ( packaging ): 260 x 210 x 130 mm

Hydraulic pump, gear pump BERARMA SP1NN/2,6R 111.10.026.00 2.2 cm3/revolution max. 250 bar shaft: conical 1/8 keyway width 2.41mm flange: 87 x 68 mm New ! Dimensions: 90 x 70 x 115 mm

Replacement diaphragm SAMSON 520-0985 Diaphragm 350 cm² New ! Dimensions ( packaging ): 260 x 210 x 130 mm

Double hydraulic pump with motor REXROTH 1PV2V4-23/80RE01MC63A1 1PF2G240/004RR20MR vane pump 1PV2V4-23 pmax.: 160 bar Vmax.: 82,8 cm3/U Gear pump 1PF2G240 pmax.: 250 bar Vmax.: 4.0 cm3/U engine: BBC QU160M4AG 11 kW 1460 rpm 380 / 660 V IP44 used, tested ! Dimensions: 1100 x 440 x 500 mm

Hydraulic pump, gear pump ORSTA 20/20.0-210 TGL 37069 ( TGL37069 ) Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 20 cm3 Nominal speed: 1500 rpm shaft: Ø 25 mm, with cone 1 : 10 Flange: 152 x 132 mm New ! Dimensions: 204 x 135 x 155 mm

Replacement diaphragm SAMSON 520-0984 Diaphragm 240 cm² New ! Dimensions ( packaging ): 265 x 100 x 140 mm

Hydraulic motor, gear motor ORSTA 20/20.0-110 TGL 37070 ( TGL37070 ) Rated torque: 57 Nm Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 20 cm3 Nominal speed: 1500 rpm shaft: Ø 25 mm, with cone 1 : 10 Flange: 152 x 132 mm New ! Dimensions: 204 x 135 x 155 mm

Mixer for adhesives SCA Schucker GmbH SD203 490 cm3 without control used, tested ! Dimensions: 650 x 650 x 1300 mm

Hydraulic motor, gear motor ORSTA 32/20.0-220 TGL 37070 ( TGL37070 ) Rated torque: 90 Nm Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 32 cm3 Nominal speed: 1500 rpm shaft: Ø 25 mm, toothed shaft profile, 18 teeth flange: 152 x 132 mm New ! Dimensions: 200 x 135 x 155 mm

Hydraulic motor, gear motor ORSTA 20/20.0-110 TGL 37070 ( TGL37070 ) Rated torque: 57 Nm Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 20 cm3 Nominal speed: 1500 rpm shaft: Ø 25 mm, with cone 1 : 10 Flange: 152 x 132 mm New ! Dimensions: 204 x 135 x 155 mm

Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg

Hydraulic pump, gear pump ORSTA 20/20.0-210 TGL 37069 ( TGL37069 ) Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 20 cm3 Nominal speed: 1500 rpm shaft: Ø 25 mm, with cone 1 : 10 Flange: 152 x 132 mm New ! Dimensions: 204 x 135 x 155 mm

-Two colours straight max paper size 38x52 cms. -Year 1993, 38 mil. copies -Kompac dampening -NP group complete with cams and wheels

Hydraulic motor, gear motor ORSTA 32/20.0-020 TGL 37070 ( TGL37070 ) Rated torque: 90 Nm Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 32 cm3 Nominal speed: 1500 rpm shaft: Ø 25 mm, toothed shaft profile, 18 teeth flange: 152 x 132 mm New ! Dimensions: 200 x 135 x 155 mm

Technical data baler: Manufacturer Europress Umwelttechnik GmbH, Germany Type EP5 150 V5 Year of construction 2015 Operating hours 19,173 hours Number of pressed bales 282,961 bales Number of press strokes from the press ram 1,895,112 press strokes Pressing force of main press 150 t Specific pressing force 181.8 N/cm² Dimensions of feed chute 1,000 x 2,000 mm (w x l) Bale dimensions 750 x 1,100 mm (h x w), length variable Drive power 2 x 55 kW + 15 kW + 2 x 0.75 kW Rated current 230 A Cable cross-section supply 120 mm² Tying 5-fold vertical, fully automatic Hydraulic oil tank capacity 4,300 l PLC control Siemens S7 / ET200S Transport weight press 35,800 kg Special equipment: Base plates and side walls made of HARDOX steel Free tamper in front of the counter blade, with cleaning cycle Scope of delivery: 1 piece baler 1 piece control cabinet 1 set of oil collecting pans under the baler 1 ...

hydraulic motor, hydraulic motor DANFOSS OMR 200 ( OMR200 ) 151-0245 nmax: 300 rpm pmax: 175 bar Vmax: 200 cm3/revolution shaft diameter: Ø 32 mm Flange diameter ( inside ): Ø 83 mm used, tested ! Dimension: 230 x 130 x 130 mm

WELLTEC TTI 450 FH injection moulding machine was manufactured in 2008 in Hong Kong. The machine of rigid steel construction, is ideal for the mass and unit production of plastic products. Plastic of sufficient plasticity is fed into an injection mould of minimum dimensions (L x W) of 125 x 125 mm, which is then clamped with a high force of up to 450 tonnes. The high clamping force and the reliable components used in the machine ensure that the user receives products of the highest quality and that productivity and efficiency are significantly increased. The WELLTEC 450 T injection moulding machine is also equipped with a CNC controller for the input and editing of all the necessary machining parameters. The total weight of the machine is 17600 kg. Technical data of the plastic injection moulding machine WELLTEC TTI 450 FH - CNC controller - maximum clamping force: 450 t (4500 kN)  ...

Double Hydraulic Pump, Hydraulic Pump, Gear Pump ORSTA 16/20.0-260 16/20.3-230 TGL 37069 ( TGL37069 ) Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 16 cm3/min Nominal speed: 1500 rpm shaft: Ø 25 mm, with cone 1 : 10 Flange: 156 x 132 mm New ! Dimensions: 360 x 135 x 180 mm

Hydraulic pump, gear pump PLESSEY C25 C25xT Nominal pressure: 200 bar Nominal flow rate: 11,3 cm3/revolution speed: max. 3500 rpm shaft: Ø 17 mm, with cone 1 : 8, thread M11 x 1.25 Flange: 112 x 87 mm hole spacing: 96 / 72 mm hole diameter: Ø 7 mm New ! Dimensions:145 x 90 x 115 mm

WELLTEC TTI 450 FH injection moulding machine built in 2008 in Hong Kong, is distinguished by its high clamping force of up to 450 tonnes and efficient high-end components. The machine designed for plastic processing uses the injection moulding method, which involves feeding plastic of suitable plasticity into an injection mould of minimum dimensions 125 x 125 mm and then clamping it with high force. As a result, high quality products are obtained in a very short time. The WELLTEC injection moulding machine has a steel structure, inside which are installed state-of-the-art components to maximise overall productivity and efficiency, and to ensure reliable operation of the injection moulding machine for many years of use. On the arm there is an operator panel with a convenient and easy-to-use CNC controller, with which the operator can enter and edit all the possible parameters of the p ...

Hydraulic motor, gear motor ORSTA 20/20.0-012 TGL 37070 ( TGL37070 ) Nominal torque: 57 Nm Speed range: 240 - 3000 rpm Nominal speed: 1500 rpm Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 20 cm3 shaft: Ø 25 mm, with cone 1 : 10 Thread: M16 x 1.5 Flange: 156 x 132 mm New ! Dimensions: 205 x 135 x 160 mm

Hydraulic pump, gear pump ORSTA 20/20.0-120 TGL 37069 ( TGL37069 ) Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 20 cm3 Nominal speed: 1500 rpm Speed range: 600 - 3000 rpm shaft: Ø 25 mm, with toothed shaft profile 25 x 1.25 x 10 flange: 156 x 132 mm New ! Dimensions: 185 x 135 x 160 mm

Hydraulic pump, gear pump ORSTA 20/20.0-110 TGL 37069 ( TGL37069 ) Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 20 cm3 < -br />Nominal speed: 1500 rpm Speed range: 600 - 3000 rpm shaft: Ø 25 mm, with cone 1 : 10 thread: M16 x 1,5 Flange: 156 x 132 mm New ! Dimensions: 205 x 135 x 160 mm

Vane pump with motor, hydraulic pump with motor REXROTH 1PV2V7-10 1PV2V7-10/100RE07MC014A1 pmax.: 160 bar (Vmax.: 100 cm3/U Engine: AEG AM 160 LO6 O4 11 kW 965 rpm 380 / 660 V IP55 used, tested ! Dimensions: 1040 x 500 x 420 mm

KUKA KR16 L6 ARC-C robotic welding machine together with the PO-2t6m-01 rotary positioner was commissioned in 2017 and its purpose was to very precisely weld gates and fence spans, but it can also weld various types of structures that fit within the range of the rotary positioner. The welding station includes a robotic arm built in 2009, which was previously only used for testing. The whole thing has only worked for 50 hours. The KUKA KR 16 L6 ARC-C robotic welding system is equipped with: – welding robot: KUKA KR16 L6 ARC-C – controller: KUKA KR C2 – rotary manipulator: PO-2t6m-01 – current power source: FRONIUS TransPuls Synergic 4000 CMT R – software: KUKA System Software (KKS) – torch cleaning device: TBi BRG-2-ES-DAE – wire feeder: FRONIUS ROBACTA DRIVE CMT – track The rail-moving KUKA KR16 ARC industrial robot with a reach of 6 m allows excellent preci ...

Axial piston pump with motor, hydraulic pump with motor SAMHYDRAULIK H1V/12 PV C DX LC ( H1V/12PVCDXLC ) 02010188 pmax.: 320 bar Vmax.: 12 cm3/U Engine: ELECTRO ADDA FCP132S/4 5,5 kW 1440 rpm 230 / 400 V IP54 motor and axial piston pump via magnetic coupling connected used, tested ! Dimensions: 990 x 320 x 370 mm

Hydraulic pump, gear pump ORSTA 12/20.2-210 TGL 37069 ( TGL37069 ) Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 12.5 cm3 Nominal speed: 1500 rpm Speed range: 600 - 4000 rpm shaft: Ø 18 mm, with cone 1 : 10 Thread: M12 x 1,5 Flange: 128 x 100 mm used, tested ! Dimensions: 165 x 105 x 130 mm

Throttle valve, hydraulic valve ORSTA, EINSPRITZGERÄTEWERK AKEN AOS 16 TGL 10962 nominal pressure: 160 kp/cm² ( approx. 160 bar ) nominal diameter: 16 mm Flow rate max: 40 l/min Pipeline installation, without check valve, with adjusting pin 2x Connection thread: M26 x 1.5 Installation length: 122 mm used, tested ! Dimensions: 122 x 142 x 62 mm

Gear pump, lubrication pump, single-flow, with internal bearings ORSTA, INDUSTRIEWERKE KARL-MARX-STADT HPf 0,63 ( HPf0,63 ) TGL 17-G G Flow rate ( V ): 0.5 m3/h Discharge pressure ( p ): 125 kp/cm² ( approx. 123 bar ) Nominal speed ( n ): 1450 rpm Flange: Ø 100 / 160 mm bolt circle diameter: Ø 125 mm 4x bore: Ø 13.5 mm shaft: Ø 18 / 20 mm Wavelength: 40 / 15 mm groove width: 6 mm New ! Dimensions: 190 x 172 x 160 mm

Hydraulic pump, radial piston pump HAWE type R1,0 pn: 550 bar V: 0,0,75 cm3/U Input: Female thread: 1/2 ( inch ) Output: Female thread: 1/4 ( inch ) Shaft diameter: Ø 15 mm Wavelength: 24 mm Groove width: 5 mm Flange diameter: Ø 63 / 100 mm bolt circle diameter: Ø 80 mm 4x threaded hole: M8 x 1.25, depth: 15 mm used, tested ! Dimensions: 175 x 105 x 135 mm

Vane pump, hydraulic pump VICKERS 25V14A 1A 22L 2137110 1 F/09/H < br /> p: max. 210 bar Q: 45 cm3/U Induction: Ø 32 mm ( inside ) outlet: DN20 ( M36 x 2,, 0 ) shaft diameter: Ø 22 mm, with flange: Ø 90 / 47 mm, bolt circle: Ø 74 mm, 4x M8 x 1.25 shaft length: 50 mm groove width: 5 mm Flange diameter: Ø 102 mm hole spacing: 142 mm hole diameter: Ø 14 mm used, tested ! Dimensions: 225 x 175 x 390 mm

Gear pump, lubrication pump, single-flow, with internal bearings ORSTA A 0,063/16L ( A 0,063/16L ) TGL 17-747401 Flow rate ( V ): 0,063 m3/h Discharge pressure ( p ): 16 kp/cm² ( approx. 16.0 bar ) Nominal speed ( n ): 1450 rpm Clutch power (pk ): 0.11 kW shaft: Ø 8 mm Wavelength: 20 mm Groove width: 2 mm Pump base: 37 x 65 mm hole spacing: 42 mm hole diameter: Ø 9.5 mm New ! Dimensions: 90 x 65 x 93 mm

Hydraulic position switch MZGA ( ) 102T 1 EM 574 A Pn: 200 kgF/cm² ( approx. 196 bar ) Qmax: 40 l/min nominal diameter: 10 mm used, tested ! Dimensions: 140 x 70 x 90 mm

ROTOR and STATOR knives, MILL BLADES, PELLETIZER KNIVES, perfectly compatible with major Constructors machinery, such as :, ADLER BUZZI ALPINE BANO CDM CMG CONDUX CUMBERLAND DIPRE ELDAN ENGINPLAST FBM FILTEC FOLCIERI FORREC GALA GAMMA MECCANICA GUIDETTI HERBOLD ISVE LINDNER MECCANOPLASTICA MOLINARI MORETTO NEUE HERBOLD NGR OMP PALLMANN PIOVAN PREALPINA PREVIERO PROMECO PRT RAPID RIETER SATRIND STOKKERMILL TECNOFER TECNOVA TPA TRIA VECOOPLAN VIRGINIO VMC WEIMA WERNER WRS ZERMA, or made on constructor’s design Made with top quality steel tempered in various hardness degrees in accordance to the specific task required., For PLASTICS, WOOD, WEEE, TIRES, AL, CABLES, COPPER, and more

-Year 1982 -Three hand fed stations -Max paper size 32x44 cms. -Two stitching heads -Three knife trimmer model DS1 -Standard delivery -Many set of spare knives -All accessoires

Hand lever pump, hydraulic pump, hand pump LUKAS HYDRAULIK Gmbh ZPH 1A/1 PN500 841200120 Pressure: max. 500 bar Flow rate per stroke (low pressure): 10 cm3 Flow rate per stroke ( high pressure ): 1.6 cm3 Automatic switching (low pressure to high pressure): at 100 bar tank capacity: 1.3 l usable quantity: 1.1 l with documents ! used, tested ! Dimensions: 710 x 210 x 175 mm

Piston manifold, single-line manifold, pre-lubrication manifold VOGEL, SKF 3x Series 355 R 355.551 ( R355.551 ), 5 outputs 1x Series 352 R 352.551 ( R352.551 ), 2 outputs Dosage: 0.2 cm3 Connection: M8 x 1.0 Other quantities on request ! New ! Dimensions ( R355 ): 97 x 80 x 20 mm Dimensions ( R352 ): 46 x 80 x 20 mm

Piston manifold, single-line manifold, pre-lubrication manifold VOGEL, SKF 1x Series 345 R 345.551 ( R345.551 ), 5 outputs 2x series 342 R 342.551 ( R342.551 ), 2 outputs Dosage: 0.2 cm3 Connection: M8 x 1.0 Other quantities on request ! New ! Dimensions ( R345 ): 100 x 52 x 16 mm Dimensions ( R342 ): 48 x 52 x 16 mm

Hydraulic pump with motor, axial piston pump PARKER pump: PV080R1K1T1NFWS Pressure ( P max ): 420 bar Continuous pressure ( pd max ): 350 bar Flow rate ( Vg max ): 80 cm3 / U Speed ( n max. ): 2500 rpm Motor: ADDA Antriebstechnik Type: FCP225MT-4 45 kW 1475 rpm 380 / 660 V 3AC, 50 / 60 Hz IP55 used, tested ! Dimensions: 1300 x 800 x 800 mm

Hydraulic pump ORSTA 16/16.0-120 TGL 37069 ( TGL37069 ) Nominal pressure: 16 MPa ( 160 bar ) Nominal displacement volume: 16 cm3 Nominal speed: 1500 rpm Speed range: 600 - 4000 rpm shaft: Ø 18 mm, with toothed shaft profile 18 x 1.25 x 10 flange: 110 x 114 mm New ! Dimensions: 155 x 110 x 114 mm

Lawn tractor with 122 cm mower deck and high discharge Engine: 3-cylinder water-cooled ISEKI diesel engine, 1,123 cm³ displacement, Stage V emissions standard (EU 2016/1628) engine power according to ECE R120 max. 15 kw/20hp / 2,600 rpm. Propulsion: Continuously variable hydrostatic drive, Differential lock on rear wheels effective Speed: forward: 0-15 km/h, reverse: 0-8 km/h Braking system. Drum brake effective on the rear axle Steering: Smooth-running fully hydraulic design, front axle made of robust cast steel, Mower: cutting width 1.22 m, 2 blades professional mower deck with rear discharge, height adjustment 25-90 mm possible. Grass pickup. 600 litre grass intake with hydr. High discharge 1.94 m incl. separating set, Dimensions: LxWxH 1410x1115x1440 mm, weight 138 kg Hydraulics: 2 functions control unit double-acting and single-acting, floating position, additional c ...

Hydraulic pump, gear pump ORSTA 12/20.2-220 TGL 37069 ( TGL37069 ) Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 12,5 cm3 Nominal speed: 1500 rpm Speed range: 600 - 4000 rpm shaft: Ø 18 mm, with toothed shaft profile 18 x 1.25 x 10 Flange: 112 x 100 mm New ! Dimensions: 155 x 105 x 115 mm

Hydraulic pump, gear pump ORSTA 6,3/20.0-220 TGL 37069 ( TGL37069 ) Nominal pressure: 20 MPa ( 200 bar ) Nominal displacement volume: 6,,3 cm3 Nominal speed: 1500 rpm Speed range: 600 - 4000 rpm shaft: Ø 18 mm, with toothed shaft profile 18 x 1.25 x 10 flange: 112 x 100 mm New ! Dimensions: 145 x 105 x 115 mm

Hydraulic motor, gear motor ORSTA 20/16 TGL 10860 ( TGL10860 ) Rated Torque: 44 Nm Rated Power: 6,6,br 9 kW Speed range: 250 - 3000 rpm Nominal speed: 1500 rpm Nominal pressure: 16 MPa ( 160 bar ) Nominal displacement volume: 20 cm3 shaft: Ø 22 mm, with spline shaft profile 6 x 18 x 22 x 5 thread: M16 x 1.5 flange: 92 x 112 mm New ! Dimensions: 170 x 95 x 115 mm

Non-return valve, hydraulic valve, unlockable ORSTA AN 20 - 16 ( AN20-16 ) TGL 10970 Nominal pressure: 160 kp/cm² ( approx. 160 bar ) New ! Dimensions ( without connectors ): 94 x 82 x 143 mm Dimensions ( with connectors ): 175 x 112 x 172 mm

TRUMPF TruPunch 3000-1300 (S11) punching machine was built in Germany in 2013. The reliable machine with extensive equipment and modern components offers its user unparalleled precision and accuracy in machining both thick and thin sheet metal. In addition to standard punching and marking, the punching machine also allows fast grooving, surface embossing, forming and chipless threading in stainless steel, structural steel and aluminium. On the machine’s sturdy and welded C” shaped structure, sits a specially designed brush table with integrated balls, designed to facilitate the loading and unloading of workpieces. The use of this type of table prevents scratches and nicks from appearing on the surface of the sheet, which results in a significant increase in the quality of the machining. During the entire production process, the sheet is held rigidly by hydraulic clamps fixed to th ...

directional control valve, hydraulic valve ORSTA 10-01.21 TGL 10939 ( 10-01.21TGL10939 ) nominal pressure: 160 kp/cm² ( approx. 160 bar ) nominal diameter: 10 mm 1x control solenoid : GS2 24 V DC New ! Dimensions: 300 x 120 x 145 mm

Hydraulic pump TOS RAKOVNIK GAR1-020-41PS-1K Nominal pressure: 16 MPa ( 160 bar ) Nominal displacement volume: 20 cm3 rated speed: 1500 rpm shaft: Ø 22 mm shaft length: 40 mm groove width: 6 mm flange: Ø 110 / 144 x 150 mm bolt circle diameter: Ø 148 mm hole diameter: Ø 13 mm control valve: VTK 20-6-350 New ! Dimensions: 390 x 275 x 150 mm

Hydraulic pump with motor, axial piston pump NACHI UPV-1A-22N1-22A-4-4412H pump: PVS-1B-22N1-U-12 Volumetric flow: 10,5 gpm ( 29.7 l/min ) Pressure: 3625 psi ( 250 bar ) Pressure range: 286 - 1000 psi ( 19.7 - 68.9 bar ) Displacement: max. 22 cm3 / U Speed: max. 2000 rpm motor: TOSHIBA Type: IK FCKLA21 100L 2.2 kW 1400 / 1680 / 1710 rpm 200 / 200 / 220 V 3AC 50 / 60 / 60 Hz IP44 New ! Dimensions: 480 x 260 x 200 mm

Interlinking unit ORSTA Type 3 TGL 10952/03 Nominal pressure: 32 MPa ( 320 bar ) for a pressure switch type COL, CML Thread: M27 x 1,5 cable connection: 2x M14 x 1.5 hole spacing mounting screws: 54 mm, 2x diameter: Ø 8.4 mm New ! Dimensions: 77 x 62 x 50 mm