We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
120,323 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
Center height: 0 mm Center distance: 0 mm Spindle bore: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Centre height: 102 mm Distance between centres: 375 mm Swing over cross-slide: 120 mm Swing over bed: 200 mm Inner taper type: 20 W Taper spindle threaded Spindle speeds: number (steps): 12 from: 40 rpm up to: 3000 rpm Taper in tailstock:: 2 MT Voltage 50 Hz 3x: 380 Volt Spindle motor: 1.5 HP Total power required: 2.0 HP Machine´s weight about: 500 kg Overall dimensions machine: Length: 1200 mm Width: 600 mm Height: 1300 mm Various accessories: Base-mounted type: Knee-operated reversing switch Driving system for milling and grinding attachment Belt-tensioning device for milling/grinding att. Drilling tailstock
used
Steam capacity at 102 ºc of nutritious water --- 10000 kg / h Heat efficiency --- 6.5mW Permissible excess pressure --- 13 Bar Working pressure --- 12 Bar Water content --- 19 m³ Total water content --- 22.6 m³ Transport weight ---- 21,3 t Working weight --- 40.6 t Fuel --- Gas and diesel Manufacturer of water --- Weishaupt Type of water --- Weishaupt G 70 / 2A Water adjustment --- Modulated The heat is the voltage of the current volume --with full fire chamber --- 1.02 mW - without full fire chamber --- 1.21 mW Boiler efficiency - at 100% productivity --- 90% - at 50% productivity --- 90.5% Boilers are still running and video is available on request
used
Center height: 0 mm Center distance: 0 mm Spindle bore: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Centre height: 102 mm Distance between centres: 375 mm Swing over cross-slide: 120 mm Swing over bed: 200 mm Spindle hole: 25 mm Inner taper type: 25 W Taper spindle threaded Spindle speeds: stepless from: 55 rpm up to: 3000 rpm Taper in tailstock:: W20 Voltage 50 Hz 3x: 380 Volt Spindle motor: 1.5 HP Machine´s weight about: 550 kg Overall dimensions machine: Length: 1200 mm Width: 600 mm Height: 1400 mm Various accessories: Base-mounted type: Knee-operated reversing switch Driving system for milling and grinding attachment Belt-tensioning device for milling/grinding att. Grinding attachment for collets B8 Wheel arbors 3-jaw chuck diameter: 100 mm 3-jaw chuck diameter: 100 mm Set of jaws hard Face plate diameter: 200 mm Driving plate Set of collets Set bell collets Tailstock ...
used
Center height: 0 mm Center distance: 0 mm Spindle bore: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Centre height: 102 mm Distance between centres: 375 mm Swing over cross-slide: 120 mm Swing over bed: 200 mm Inner taper type: 20 W Spindle speeds: number (steps): 12 from: 45 rpm up to: 2800 rpm Taper in tailstock:: 2 MT Voltage 50 Hz 3x: 380 Volt Spindle motor: 0.5 HP Machine´s weight about: 300 kg Overall dimensions machine: Length: 1200 mm Width: 700 mm Height: 1500 mm Various accessories: Base-mounted type: Belt-tensioning device for milling/grinding att. 4-jaw chuck diameter Quick closing attachment Drill chuck Hand rest Fixed steady
used
Center height: 0 mm Center distance: 0 mm Spindle bore: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Centre height: 102 mm Distance between centres: 375 mm Swing over cross-slide: 120 mm Swing over bed: 200 mm Inner taper type: 20 W Spindle speeds: number (steps): 12 from: 45 rpm up to: 2800 rpm Taper in tailstock:: 2 MT Voltage 50 Hz 3x: 380 Volt Spindle motor: 0.5 HP Machine´s weight about: 300 kg Overall dimensions machine: Length: 2000 mm Width: 900 mm Height: 1500 mm Various accessories: Working bench: Length: 2000 mm Width: 1000 mm Height: 900 mm Rear drive Pneum. quick closing attach. Milling attachment Cross slide CNC: COMBITEC E-600
used
Center height: 0 mm Center distance: 0 mm Spindle bore: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Centre height: 102 mm Distance between centres: 375 mm Swing over cross-slide: 120 mm Swing over bed: 200 mm Inner taper type: 20 W Spindle speeds: number (steps): 12 from: 45 rpm up to: 2800 rpm Taper in tailstock:: 2 MT Voltage 50 Hz 3x: 380 Volt Spindle motor: 0.5 HP Machine´s weight about: 300 kg Overall dimensions machine: Length: 2000 mm Width: 900 mm Height: 1500 mm Various accessories: Working bench: Length: 2000 mm Width: 1000 mm Height: 900 mm Rear drive Pneum. quick closing attach. Cross slide CNC: COMBITEC E-600
used
Center height: 0 mm Center distance: 0 mm Spindle bore: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Centre height: 102 mm Distance between centres: 450 mm Swing over cross-slide: 120 mm Swing over bed: 200 mm Spindle hole: 20 mm Inner taper type: 20 W Taper spindle threaded Spindle speeds: stepless from: 210 rpm up to: 3000 rpm Voltage 50 Hz 3x: 380 Volt Spindle motor: 1.5 HP Total power required: 2.0 HP Machine´s weight about: 200 kg Overall dimensions machine: Length: 2500 mm Width: 800 mm Height: 1300 mm Various accessories: Working bench: Length: 2000 mm Width: 700 mm Height: 900 mm Driving plate Drilling tailstock Drill chuck Fixed steady
used
electric box lifting device, lift lift Brand: KLB Type: Lifter 1000 Built: 2013 Load capacity: 2000N, approx. 200kg maximum lifting height: 102 cm Crate dimensions: 62 x 62 cm Trolley with spindle drive Forks to hang in Cable for power supply Control panel with cable This item is only sold to traders. All information without guarantee
used
Center height: 0 mm Center distance: 0 mm Spindle bore: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Centre height: 102 mm Distance between centres: 375 mm Swing over cross-slide: 120 mm Swing over bed: 200 mm Inner taper type: 20 W Taper spindle threaded Spindle speeds: number (steps): 12 from: 40 rpm up to: 3000 rpm Taper in tailstock:: 2 MT Voltage 50 Hz 3x: 380 Volt Spindle motor: 1.5 HP Total power required: 2.0 HP Machine´s weight about: 500 kg Overall dimensions machine: Length: 1200 mm Width: 600 mm Height: 1300 mm Various accessories: Speed potentiometer 2 drawers
used
Current stock: approx. 370 pcs. Included in delivery are: 01x Bockrolle, used Manufacturer: Wicke Material color roll: cream white Material color frame: sendz. galvanized Specifications: Total height: approx. 150 mm Rolls Ø: approx. 125 mm Roll width: approx. 40 mm Roll material: Polyamide Plate abbreviation: approx. 102 x 87 mm (WxD) Hole Ø: approx. 9 x 11 mm ( oval ) Number of holes: 4 pcs Screw hole removal: approx. 80 x 60 mm (middle - middle hole) Weight / pcs.: approx. 0.745 kg Advantages to PA wheels: - The PA wheels are very low in wear. - They leave no traces on the ground. - PA wheels have a very low rolling resistance. General information about the article: This item is offered for pickup only. A desired transport beyond that or a dispatch of this article is associated with additional costs, which separately depending on the place of deli ...
new
We offer high-performance automatic vacuum can seamer based on Ferrum F240,F506G, F706G, F708G(4,6,8 heads) beverage seamer. The basic machine has been completely upgraded and adapted for vacuum food cans. These seaming machines are affordable relativle fast avaible and reliable for long time. Capacity from 350 to 750 cans/min. Lid diameter from 53 to 102 mm Can diameter from 50 to 99 mm Can height from 35 to 120 mm Standard equipment: • With progressive pre-vacuum feeder • With complete seaming tooling • With lid feeding system into the vacuum chamber • The machine has variable speed with frequency converter control • Independent synchronized infeed with frequency converter control • Main Electrical Control Cabinet INOX • Vacuum pump connection and controlled by main cabinet - Speeds below are guaranteed regardless of the type of the lids (standard NEO, ea ...
D 102 x L 78 x d 90 mm, material cast iron Plate 3.1B, No. 83
used
Electric pallet truck, low-lift truck Low-lift trucks, electric pallet trucks Manufacturer Yale Type MP16 Built in 2015 only approx. 300 operating hours incl. charger Ansolut new condition with only 102 operating hours! Special price
D 102 x L 78 x d 90 mm, material cast iron Plate 3.1B, No. 83
used
8 up Thermal CTP Model: Screen 8600 (Topsetter 102) 64 diodes Year: 2004 with Loader AT-T 8001 Year: 2001 Stacker Plate Counter: 316,000 Price: on request
used
Technical data Table length: 1880 mm Table width: 915 mm Longitudinal travel (X-axis): 1540 mm Cross travel (x-axis): 1285 mm Vertical travel (z axis): 985 mm Table load max.: 7000 kg Drill spindle diameter: 102 mm Drill spindle travel: 760 mm Spindle speeds: from: 10 rpm up to: 1300 rpm Integrated rotary table 4.axis Length: 1520 mm Width: 1220 mm axe rotatif table tournante: 360 ° Voltage 50 Hz 3x: 380 Volt Machine´s weight about: 18000 kg Overall dimensions machine: Length: 4850 mm Width: 2820 mm Height: 2920 mm Various accessories: Digital readout number of axis:: 3 Manufacturer: Heidenhain Set of cutter arbors
used
Reference number 20107 Brand Gearbox ZF GERMANY Model Gearbox BW 465 Ratio 2,759:1 A Serial number 102 General condition TAKEN OUT RUNNING EX MILITARY FAST CRAFT Status AVAILABLE Sae housing 30 Flexible coupling NO Controls YES - INCLUDING CABLES AND ELETRONIC ACTUATOR SPECIFIC FEATURES Brackets YES Oil cooler YES Pto YES- FLANGE Weight (kg) 735 KG
used
suitable for XL 105, SM / CD 102, can be converted to standard feeder, Preset or Preset Plus feeder
used
Turning diameter: 750 mm Turning length: 1605 mm Turret positions: 12 CNC Brand: Mazatrol CNC Model: Matrix Nexus MACH - ID 6102 Make: MAZAK Type : QTN 350 II - M Control: Mazatrol Matrix Nexus YOP: 2007 Hours: 9000 Max. turning Ø 750 mm X-Axis 260 mm Z-Axis 1.605 mm Spindle bore 102 mm Speedrange 3300 Rpm Spindle power 30 kW ATC / revolver 12 Speed live tools 4000 Rpm Control MAZATROL MATRIX NEXUS Chip conveyor Yes Tool eye Yes Pi ...
used
Turning diameter: 670 mm Turning length: 3190 mm Turret positions: 0 Positions ATC: 0 Number controlled axis: 0 CNC Brand: Fanuc MACH - ID 6090 Make:DOOSAN Type:PUMA 3100 ULY Control:FANUC YOP:2010 Hours:5800 Max. turning Ø 670 mm X-Axis 293 mm Y-Axis 130 mm Z-Axis 3.190 mm Spindle bore 102 mm Speedrange 2800 Rpm Spindle power 25 kW Speed live tools 5000 Rpm Control Fanuc Chip conveyor Yes Tool eye Yes Pinole taper Mk 4 Mk Dimensions Length 6.600 mm Width 2.880 mm Height ...
used
Turning diameter: 680 mm Turning length: 1500 mm Turret positions: 12 CNC Brand: Mazatrol CNC Model: Matrix Nexus MACH-id 6001 MAKE Mazak TYPE NEXUS 350 II M YOP 2007 SPECIFICATIONS Max. turning Ø 680 mm X-Axis 350 mm Z-Axis 1600 mm Spindle bore 102 mm Speedrange 4500 Rpm Spindle power 30 kW ATC / revolver 12 Speed live tools 4000 Rpm Control ...
used
Brand: Climaveneta Power: 102 kW Year of manufacture: 2001 Refrigerant circuit: 2 pcs. Type of refrigerant: R404а Compressors: 2 pcs. Copeland Dimensions: 1.97 х 970 х 1.30 m. Weight: 800 kg. Country: Italy Condition: Good condition
used
Turning diameter: 680 mm Turning length: 1200 mm Turret positions: 12 CNC Brand: Mazatrol CNC Model: Matrix Nexus MACH-id 4137 MAKE MAZAK TYPE Nexus 350 - II YEAR 2007 SPECIFICATIONS Swing over bed Ø 680 mm Control MATRIX Swing over cross slide 420 mm Distance between centres 1200 mm Spindle bore 102 mm Spindle speeds / ranges 3000 Rpm Power 30 Kw DIMENSIONS Length 3700 mm Width 2000 mm Height 2000 mm Revolver 12 stations Kitagawa 12 inch chuck Steady rest over cnc
used
Center distance: 350 mm Grinding head Z-axis: 275 mm Center height: 0 mm CNC Brand: Fanuc CNC Model: 16 M MAKE Viking Denmark TYPE US-250 PRO YEAR 1998 SPECIFICATIONS Controll Fanuc 16M Cylindical / Surface / Other 5 Axis tool grinder Grinding diameter Ø 280 mm Grinding length 350 mm X - Travel X = 850 mm Y - Travel Y = 230 mm Z - Travel Z = 275 mm Electro magnetic table A = 360 Gr mm Work piece weight U = 255 Kg Grinding wheel size W = 102 Gr mm kW power on spindle 6.7 kW Spindle speeds / ranges 8000 Rpm Internal grinding attachment ISO 50 Coolant / Filtration /Filtration DIM ...
used
Plate heat exchanger,stainless steel,Pasilac type N35 MGS,102 plates
used
Center distance: 350 mm Grinding head Z-axis: 275 mm Center height: 0 mm CNC Brand: Fanuc CNC Model: 16 M MAKE Viking Denmark TYPE US 250 YEAR 1997 SPECIFICATIONS Controll Fanuc 16 M Cylindical / Surface / Other 5 axis tool grinder Grinding diameter Ø 280 mm Grinding length 350 mm X - Travel X = 850 mm Y - Travel Y = 230 mm Z - Travel Z = 275 mm Electro magnetic table A = 360 Gr. mm Work piece weight U = 255 Kg Grinding wheel size W = 102 Gr mm kW power on spindle 6.4 kW Spindle speeds / ranges 8000 Rpm Internal grinding attachment ISO 50 DIMENSIONS Length 2400 mm Width 1980 mm Height 2150 mm Viking 5 Axis CN ...
used
Floor cleaning machine make NILFISK-ALTO type Scrubtec R 586Code 00311E ser. -No: EB2511 year 2007Cleaning width: 860 mmTank volume: 110 lArea / theor. / Prak.:5680 / 3980 m² / h.Brush print: 0 - 102 kgBrush speed: 300 rpm.Brush size: 2 x 430 mm Drm.Drive power: 450 WBrush motor: 1850 WWorking speed: 4.0 km / hDrive system: battery 36 VWeight approx .:540 kgOutside dimensions approx: 1664 x 899 x 1260 mmvery little used, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools
used
max. wheel diameter: 400 mm gear width: 0 mm module: pinion diameter - max.: 254 mm axial cross angle: 90 ° total power requirement: 15 kW weight of the machine ca.: t dimensions of the machine ca.: m This machine is very suitable for precision production testing of spiral and hypoid bevel gears with shaft angle 90°. The gear spindle is vertical and the pinion spindle is horizontal. The pinion cone distance can be adjusted while the machine is working in order to find the optimal mounting position whereby the gear is loaded with a preset torque. The axial pinion position can be adjusted until the quietest meshing position of the traction flank is found. Likewise, the thrust flank can be tested during the return run. Marking compound is sprayed on both sides of the teeth so the flank contact pattern can be seen. Working cycles, as well as the positioning in the tooth gap, are automat ...
new
axis stroke (X,Y,Z): 3950,2145,555 mm Number of spindle head vertical: 13 St. Number of spindles head horizontal: 6 St. Number of tools: 22 St. Number of milling agregates: 1 St. working dimensions: 3200x2000x200 mm Motor output: 12 kW Control: Beckhoff CNC Number of axles: 5 St. Masterwood Project 385 CNC-Bearbeitungszentrum --------------------------------------------- 5-Achs CNC-Bearbeitungszentrum in Auslegerbauweise (dadurch sehr große PLatten auflegbar) für Innenausbau, Plattenbearbeitungen aller Art. Kurze Zusammenfassung: --------------------------------------------- Verfahrwege X = 3950 mm, Y = 2145 mm, Z = 555 mm Arbeitsbereich: X = 3200 mm, Y = 2000 mm, Z = 200 mm 1 Stk. 5-Achs-Hochleistungsspindel, 12 kW, mit HSK 63 F Aufnahme 1 Stk. fest installierter Bohrkopf mit 19 Spindeln mit 7 einzeln abrufbaren Vertikalbohrspindeln X-Richtung mit 6 einzeln abrufbaren Vertikalbohrspin ...
new
pressure: 10 bar : 660 l/min. : 520 l/min. turning speeds: 1000 U/min container volume: 90 l power capacity: 4 kW voltage: 400 V weight: 102 kg dimensions: 1110x495x1015 mm - Mobile piston compressor with horizontal tank - Compressed air tank equipped with safety valve, container pressure gauge and condensate drain valve The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
spindle diameter: 102 mm x-travel: 1600 mm y-travel: 1200 mm z-travel: 1500 mm w-axis: 700 mm Table dimensions: 1250x1400 mm number of spindle speeds: 8-1600 Control: Heidenhain TNC 131 total power requirement: 15 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
spindle diameter: 102 mm x-travel: 1600 mm y-travel: 1210 mm z-axis: 1475 mm spindle travel: 710 mm B-axis (table): 360 ° Table dimensions: 1250x1400 mm Table load: 3500 kg T-slots: 22H7 T-slot - distance: 125 mm spindle turning speed range: 4-1600 U/min spindle drive: 16,5 kW Control: total power requirement: 47 kW weight of the machine ca.: 9,25 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
spindle diameter: 102 mm x-travel: 1600 mm y-travel: 1000 mm z-travel: 1600 mm Control: Heidenhain type: TNC 410 table surface area: 1000x1120 mm Table load: 3000 kg spindle stroke: 710 mm spindle turning speed range: 4-1600 U/min main drive motor: 13 kW total power requirement: kW weight of the machine ca.: 12 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
saw blade diameter: 300 mm capacity 90 degrees: round: 102 mm capacity 90 degrees: square: 90 mm capacity 90 degrees: flat: 120x80 mm capacity 45 degrees: round: 90/80 mm capacity 45 degrees: square: 80/70 mm capacity 60 degrees: flat: 90x70/85x70 mm total power requirement: 1,5/2,0 kW weight of the machine ca.: 0,135 t dimensions of the machine ca.: 0,5 x 1,05 x 1,0 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
with Freeflow Printserver and Clear Toner M. No.: 3130055185 Counter (m): 7.3 Colors: 4 + varnishes Format : A7 – A3+ (SRA3) Equipment / Additional information: Image Resolution: 2400 x 2400 dpi VCSEL ROS Productivity/Print Speeds—AWM • 80/100 ppm (8.5" x 11"/A4 letter), all weights 55–350 gsm (15 lb Bond to 130 lb Cover) • 4800/6000 full process color A4 (letter) 4/0 impressions per hour • 44/50 ppm (11" x 17"/A3–12" x 18"/SRA3), all weights 55–350 gsm (15 lb Bond to 130 lb Cover) • 2400/3000 (11" x 17"/A3–12" x 18"/SRA3 tabloid) 4/0 impressions per hour and 4800/6800 (8.5" x 11"/A4) IMP Paper Format/Sizes • Maximum Sheet Size: 13" x 19.2" (330 x 488 mm) • Minimum Sheet Size: 7.2" x 7.2" (182 x 182 mm), tray inserter kit supports for 4" x 6" (102 mm x 152 mm); see Optional High Capacity Feeder • Maximum Print Area: 12.83" x 19.05" (326 mm ...
new
saw blade diameter: 355 mm capacity 90 degrees: round: 115 mm capacity 90 degrees: square: 120 x 106 mm capacity 90 degrees: flat: 102 x 197 mm : 25,4 mm connected load frequency: 230 V total power requirement: 2,3 kW weight of the machine ca.: 28 Kg Dimensions (LxWxH): 0,6 x 0,35 x 0,45 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
I-beam section - flat steel: 220 bei Dm 1200 mm I-beam section - upend: - mm angular steel - leg outwards: 110x110x14 bei Dm 1000 mm angular steel - leg inwards: 80x80x10 bei Dm 1000 mm flat steel flat: 100 x 20 bei Dm 1000 mm T-steel / side out: 120x120x13 bei Dm 1200 mm U-iron on the x-axis: 22 bei Dm 1200 mm pipes: 102 x 6 bei Dm 900 mm round material: 75 bei Dm 700 mm square material: 60 x 60 bei Dm 600 mm bending speed: 3,5 m/min No. - Rolls: 3 Drive: 7,5 kW shaft diameter: 125/135 mm weight: 6,4 t dimensions of the machine ca.: 2,1 x 2,4 x 1,5 m Condition: ready for operation: Electric 380 Volt: Set of standard rolls: I + H Motorized adjustable rollers: Control panel: Central lubrication: autom. Rolls for round material: 100 mm Machine manual: Heavy ASYMETRIC ring bending machine with mot. adjustment of both infeed rollers and mot. adjustment of the two lateral guide rollers, ...
used
We offer a Doka Frami wall and foundation formwork 223m² complete with many accessories. The formwork is 90% newly covered with new Finply birch formwork 220- 240g/m²phenolic resin coating. The rest of the elements are controlled and sorted and covered with original Doka Xlife formlining. Fair-faced concrete class 2/3 possible without any problems. New value approx. 156108,00€ Special price 62359,00€ 3 Frami Xlife element 0,90x2,70m 1 Frami Xlife-Uni-Element 0,90x2,70m 3 Frami Xlife element 0,75x2,70m 3 Frami Xlife element 0,45x2,70m 19 Frami Xlife Element 0,30x1,50m 2 Frami Xlife element 0,45x1,50m 51 Frami Xlife element 0,60x1,50m 35 Frami Xlife element 0,75x1,50m 2 Frami Xlife element 0,75x1,50m 7 Frami Xlife element 0,90x1,50m 6 Frami Xlife element 0,90x1,50m 9 Frami inner corner 1,50m 20cm 2 Frami inner corner 1,50m 20cm 7 Frami outer corner 1,5 ...
used
faceplate diameter: 610 mm adjustment: 200 +/- mm spindle bore: 102 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
Aluminium format slide (anodized) with hardened Steel guide rods. Non-return protection at thickness planer. Anodized parallel fence with micrometric fine adjustment. Inclined adjustment of the saw blade up to 45° by means of a hand wheel. Table opening ø190 mm with undercounter extraction. Milling stop 180 mm. Built-in milling spindle lock. Layout table with telescopic stop, Eccentric clamp, degree grid made in EU ! Dressing unit: Table width 410 mm Table length 1800 mm Planer shaft diameter 100 mm Number of planing knives 4 pieces Shaft speed 5000 Motor output power 5 kW S6 400V (4kW S1) Thickness unit: Thickness passage, min/max 4 - 230 mm Feed speed 7m/min Milling machine: Usable length of the spindle 125 mm Spindle height adjustment 160 mm tool diameter for profiling 180 mm for tenon cutting 250 mm Spindle speed 8000/6000/3500/1400 Table openings 1 ...
used
turning diameter over bed: 1400 mm turning diameter over slide rest: 1045 mm turning length: 8000 mm turning dia. in gap: 1745 mm spindle diameter: 102 mm speed: 2,8 - 400 m/min voltage: 380 V total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Center height: 0 mm Center distance: 0 mm Spindle bore: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Centre height: 102 mm Distance between centres: 470 mm Swing over cross-slide: 120 mm Swing over bed: 200 mm Bar passage: 14.5 mm Inner taper type: 20 W Taper spindle threaded Spindle speeds: stepless from: 100 rpm up to: 6000 rpm Cross slide: cross travel (x axis): 100 mm Longitudinal travel (X-axis): 90 mm Taper in tailstock:: 2 MT Spindle diameter: 30 mm Spindle stroke: 80 mm Voltage 50 Hz 3x: 380 Volt Spindle motor: 1.5 kW Machine´s weight about: 360 kg Overall dimensions machine: Length: 2000 mm Width: 800 mm Height: 1370 mm
new
Original MINGORI® Model OB40 - Mobile hydraulic tube bending machine with manually operated hand pump, suitable for bending pipes according to DIN, API and ASA standard, as well as coated PE-HD pipes. The machine works in the compression bending process. The greatest surmountable material resistance torque that can be overcome with the machine is about 28 cm³. Maximum bending force 18 tons Maximum bendable pipe diameter 88.9 mm Smallest possible bendable pipe diameter 17.2 mm Smallest bending radius depending on the radius of the bending punch from 46.5 mm to 330 mm Smallest bending angle 110° (this machine also available for bending angles up to 180°) Weight of the basic machine approx. 140 kg The machine is delivered in a storage chest – Dimensions of the chest approx. 102 x 32 cm x H 41 cm Weight basic machine 140 kg With electrically operated hand pump (as mo ...
used
Center height: 0 mm Center distance: 0 mm Spindle bore: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Centre height: 102 mm Distance between centres: 470 mm Swing over cross-slide: 120 mm Swing over bed: 200 mm Spindle hole: 25 mm Bar passage: 19 mm Inner taper type: 25 W Taper spindle threaded Spindle speeds: stepless from: 100 rpm up to: 6000 rpm Cross slide: cross travel (x axis): 100 mm Longitudinal travel (X-axis): 90 mm Taper in tailstock:: 2 MT Spindle diameter: 30 mm Spindle stroke: 80 mm Voltage 50 Hz 3x: 380 Volt Spindle motor: 1.5 kW Machine´s weight about: 360 kg Overall dimensions machine: Length: 2000 mm Width: 800 mm Height: 1370 mm
used
CNC controller: SINUMERIK 810D with ShopTurn Capacity: X-axis travel mm: 300 Z-axis travel mm: 1.050 Turning length mm: 1.050 Max. turning diameter mm: ø 465 Swing over bed mm: ø 680 Swing over cross-slide mm: 465 Bar work capacity mm: ø90 Upper turret: Number of tool slots St .: 12 (6x driven) Speed driven tools RPM: 4.000 Main spindle: Speed spindle rpm: 3.250 Drive power spindle kW: 33/22 (40%/100% DC) Spindle bore mm: 102,5 Spindle nose: Flat flange (220h5) Maximun torque Nm: 420 (100% DC) Tailstock: Tailstock travel mm: 850 Holder: MK5 Equipment: part catcher Workarea light Foot switch for chuck or collet system Driven tools included Working time hours Spindle 1: 72.059 Rated power kVA: 50 Basic machine dimensions / weight: Length mm: 5.300 Width mm: 2.230 Height mm: 2.010 Weight kg: 8.100
used
Center height: 0 mm Center distance: 0 mm Spindle bore: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Centre height: 102 mm Distance between centres: 470 mm Swing over cross-slide: 120 mm Swing over bed: 200 mm Spindle hole: 20.0 mm Inner taper type: 20 W Taper spindle threaded Taper in tailstock:: 2 MT Voltage 50 Hz 3x: 380 Volt Machine´s weight about: 500 kg Overall dimensions machine: Length: 1300 mm Width: 600 mm Height: 1300 mm Various accessories: Base-mounted type: Knee-operated reversing switch 2 drawers Driving plate Cross slide with 90 mm stroke Hand rest
used
HEIDELBERG Nela Plate Bending suitable for HD SM 52 / 74 /102 and XL machines different years of construction available
used
HEIDELBERG Nela plate punch Suitable for HD SM 52 / 74 /102 and XL machines Hole spacing: 425 mm and 780 mm Various year of manufacture models available
used
Concept Laser Here we offer you a Concept Laser M2 cusing Multilaser. Concept Laser M2 cusing Multilaser: System technology for safe processing of aluminum and titanium alloys etc. External dimensions: 2542 x 1818 x1987 mm (WxDxH) Weight: 2300 kg 2 lasers 400W Power supply: 3P/N/PE AC 400 V, 32 A 5 bar compressed air required Shielding gas possible through 2 connections for external N2 generators (optional) Build volume 250 x 250 x 280 Layer thickness 20-80μm Production speed 2-20cm³ (depending on material and laser power) Operating conditions 15-35 degrees Celsius Laser service life Laser 1: 501.973 hrs Laser 2: 503.411 hrs Other devices: Lifting device Inox 200 Weight: 102 kg Max lifting capacity 135 kg Protection class IP65 Wet cutter NA 7-11 H CL EU Zone 22 Dimensions: 800x480-570x755-850 mm Drive type: AC Power: 1.25 kw Voltage: 230 V 9.2 A IP65 pro ...
used
stamp capacity: 2 - 63 mm throat: 110 / 200 mm Various Destaco punching iron, some with accessories: No. 1 & 2: Type 101-200, accessories: one punch + one die, technical data: see picture, price per piece: 150,- No. 3 & 4: Type 102-200, accessories: approx. 12 sets of punches and dies, technical data: see picture, price per piece incl. accessories: 350,- No. 5: Type 104-200, accessories: 2 punches and 3 dies, technical data: see Picture, price: 350, - No. 6 & 7: Type 103-200, accessories: approx. 12 sets of punches and dies, technical data: see picture, price per piece incl. accessories 500,- 1 Raskin punching iron type 10 JL 200, throat 210 mm, install height 238 mm, material thickness 3 mm in max. 40 kg/mm². pice 175,-- EUR 1 Raskin punching iron type 15 BL 100, throat 110 mm, install height 149 mm, material thickness 3 mm in max. 40 kg/mm². pice 120,-- EUR Diverse punching dies. We ...