cat 3520 e used for sale

Mains filter for frequency converters, PLC control, mains filter, mains filter -Lenze: Mains filter E94AZMS0094 -Dimensions: 530/100/H70 mm -Weight: 6.1 kg

Braking resistor, charging resistor, damping resistor, filter resistor -Lenze: Brake resistor ERBS047R400W -Resistance: 47 Ohm/400W/800V -Dimensions: 480/110/H125 mm -Weight: 2.6 kg

Eisele cold circular saw LMS 2 380 V 16 A 1700 - 3400 rpm 1 clamping jaw without locking

Eisele LMS 1 Speed 4000 rpm 380 V 16 A Untested without plug Swivel table Vice

Timing relay, relay, heating current monitoring, contactor, semiconductor contactor, contactor, compact smart relay -Manufacturer: Schneider Electric -Type: SR1 A201BD -Dimensions: 125/90/H55 mm -Weight: 0.3 kg

Gear motor, electric motor, electric gear motor -Manufacturer: SEW-Eurodrive, gear motor type SA52 DT71D-4BMG -Speed: 9.3 rpm -Power: 0.37 kW -Hollow shaft: Ø 40 x 120 mm -Protection class: IP54 -Brake: 5 Nm -Bearing block: THK HSP 30 -Dimensions: 520/260 / H285 mm -Weight: 36 kg

Line filters, power line filters, three-phase filters, three-phase line filters -Manufacturer: EPCOS -Type: FS.06.3.50 -Voltage: 440/250 V/3 x 16 A/50-60 Hz -Dimensions: 200/155/H80 mm -Weight: 3.6 kg

Tool grinding machine, grinding machine, angle grinder, turning tool grinding machine, steel grinding machine -3x grinding wheels: Ø 340 mm, speed 1500 rpm -1x grinding wheel: Ø 170 mm, speed 3000 rpm -Max. steel cross-section: 80 x 80 mm -Dimensions: 1300/900/H1450 mm -Weight: 500 kg

Geared motors SEW TYPE K29DRS71M4BE05/ASE1/TF/AS7W 50 HZ r/min 1360 0.55 KW 380 V IP 54 I 27,23 Nm 105/84 Absolute speed sensor Baumer AK8Y / Ak8W Gearbox output shaft d 25 mm

Line SEW Eurodrive NF 085-503 Part No. 08274150 No.0009405 UN : 3x380V IN: 85 C° Connections 35 mm2

Airpower Europe APD 060 090 F05/F07-V14-H MD 7Nm/bar Pneumatic swivel actuator double-acting Valve monitor - Feedback box Model LSB 02-M2 IP 67 230 V Outer D 185 mm Inside D 155 mm Thickness 4 cm Outer steel

pressure: 20 t throat: 185 mm stroke: 100 mm table surface area: 380 x 350 mm dayligth: 250 mm table height over floor: 840 mm total power requirement: 4 kW weight of the machine ca.: 1,3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Rotary table, rotary indexing table, dividing head, dividing head -Clamping surface: Ø 320 mm -Bore center: Ø 25/40 mm -Height: 110 mm -Groove width: 14 mm -without transport hook -Dimensions: 540/470/H200 mm -Weight: 64 kg

4-application chucks, wedge bar chucks, three-jaw chucks, three-jaw lathe chucks, power chucks, hydraulic chucks -Spare parts: for hydraulic power chucks different types -Chuck size: Ø 210 mm -Weight: 124.2 kg

Compressors, control, compressor control, control panel -Handover: in its current condition as inspected -Cover bottom: damaged, see photo -Manufacturer: Ecoair -Type: Multitronic Control -Dimensions: 280/295/H120 mm -Weight: 2.6 kg

Wire feed case for inert gas welding device, shielding gas device, wire feed case -Manufacturer: Ess wire feed case, water-cooled -Type: DVK 300-3 -Accessories: hose package -Dimensions: 750/410/H430 mm -Weight: 32 kg

ESAB EAGLE 2000 plasma cutting machine was built in 2009 in Germany. The machine is designed for machining stainless steel, structural steel, low-alloy steel and aluminium with a maximum thickness of 30 mm and has a very stable and vibration-free welded construction. Excellent cutting precision with simultaneous low operating costs is ensured by the ESAB Precision Plasmarc 201 plasma source with a power of 200 A, which generates a narrow plasma beam with high energy density per small area of material. The plasma cutting machine portal was fixed by two dynamic servo drives operating with low backlash on the machined profile rails (X axis). The dynamic servo drive in the transverse carriage drives the spur gear, which then meshes with the toothed bar of the machine portal, causing transverse movement (Y axis). The plasma cutting machine is equipped with an ESAB CNC control with the late ...

Gear motor, electric motor -SEW-Eurodrive: gear motor type RF60DT90S4B -Speed: 72 rpm -Power: 1.1 kW -Construction: B5 -Brake: 10 Nm -Diameter shaft: Ø 30 x 60 mm -Protection class: IP 44 -Dimensions: 620/280 / H215 mm -Weight: 41 kg

Gear motor, electric motor, three-phase motor -Gearbox: SEW type R17/A/112GD -Motor: SEW type R17/112GD DR63L4/TF/II3GD -Power: 0.25 kW -Speed: 36 rpm -Shaft: Ø 20 x 40 mm -Construction: B3 -Protection class: IP 54 -Dimensions: 355/180/H140 mm -Weight: 8.5 kg

Relay, contactor, semiconductor contactor, contactor -Elero: Uni-Tec 868 wireless wall transmitter -Application: roller shutters, awnings blinds, special applications -Price: per piece -Number: 1 pieces -Dimensions: 81x81x22 mm (LxWxD) -Weight 0.1 kg/piece

Motor contactor, auxiliary contactor, contactor, semiconductor contactor, contactor -Manufacturer: TM, contactor -Type: EV3-1 -Voltage: 220 V 50-60 Hz -Dimensions: 110/75/H70 mm -Weight: 0.4 kg

Motor contactor, auxiliary contactor, contactor, semiconductor contactor, contactor -Manufacturer: TM, contactor -Type: EV3-2 -Voltage: 220 V 50-60 Hz -Dimensions: 110/75/H70 mm -Weight: 0.4 kg

Power resistor, wire potentiometer, resistor, braking resistor, fixed pipe resistor, high-current resistor -Manufacturer: Ifo, 4 pieces EMF 50 6.8 ohms in series -Dimensions: 200/50/H110 mm -Weight: 0.4 kg

Stop for press brake, bending machine, guillotine shear, drive shaft -Drive shafts: for stop, from press brake EHT type EHP 11-40, 2 pieces -Length: 515 mm -Hole: Ø 25 mm -Price: complete -Dimensions: Ø 50 x 515 mm -Weight 5.1 kg/pc.

Bending tool, die, upper knife, upper tool, straight tool, die tool, seam closing tool -Tool: from press brake EHT type EHP 11-40 -Measures: see drawing in the photos -Dimension: 4050/45 / H130 mm -Weight: 147 kg

2 weeks offer - will not last Hypet400HPP P100 120 E140 year 2011 Plastcis systems auxiliaries NO MOLD working hours 70k Motivated seller

2 weeks offer - will not last Hypet400HPP P100 120 E140 year 2011 Plastcis systems auxiliaries NO MOLD working hours 77k Motivated seller seller offer No. resale 070623B

Conveyor Belt, Belt Conveyor Belt, Conveyor Belt, Belt Conveyor, Chain Conveyor, Pallet Conveyor Belt, Pallet Conveyor -Drive: geared motor SEW-Eurodrive with brake 0.55 kW/15 m/min -Weigh cell: Bizerba HLC-C3 -Chain track width: 750 mm -Dimensions: 1995/990/H480 mm -Weight: 334 kg

Flame cutting system, torch, oxyfuel cutting system -Shaft diameter: 30 mm -Shaft length: 220 mm (260 mm with socket) -Total length: 405 mm -for: 16 mm nozzle diameter -Weight: 1.3 kg

length: mm height: mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Pulse welder Hybrid 4002 Year of manufacture 2005 Feeding device / 4 rolls wire feed DV 39 machine no.: 940 16 222 - Welding hose 4000mm - Ground cable 70 square 5000mm - Intermediate hose package approx. 4000mm - Hose package Binzel MB511 Pulse current The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Power supply, power supply, DIN rail power supply, switching power supply -Manufacturer: EMS, Power Supply -Type: D602 -Input: 115/230 V 50/60 Hz -Output: 5 V 500 mA -Dimensions: 115/100/H50 mm -Weight: 0.7 kg

Power supply unit, converter, power supply, switching power supply unit, remote-controllable socket strip -Leunig: ePowerswitch EPS 4G -Voltage: 110 V -4 sockets: remote controllable -Incl. Accessories: see photo -Dimensions: 220/260/H55 mm -Weight: 1.6 kg

Cooling water pump, centrifugal pump, water pump, coolant pump, drilling water pump, submersible pump, switching pump -Manufacturer: Forst-Enor, switching pump RSWV40 -Motor: AEG -Power: 4 kW -Speed: 1420 rpm -Delivery rate: 40 l/min -Dimensions: 2000/455/H500 mm -Weight: 156 kg

Transformer, transformer, converter, three-phase autotransformer -2 pieces: three-phase transformers DTST 7.5 -with: additional electronic modules -Primary: 400 V -Power: 5.5 kVA each -Dimensions: total 200/430/H740 mm -Total weight: 164 kg

For vegetable

Capacity, ton 1250 Stroke, mm 500 Min number of no-load stroke: 8 /per min Slider adjustment, mm 215 Max. shut height between bolster plate and slider (stroke down, adjustment up), mm 1100 Table size, mm 1600 x 1850 Slider size, mm 1300 x 1400 Table gap size, mm 1100 x 1100 Distance between columns, mm 1630 Distance between slides, mm 1580 Cushion travel, mm 200 Cushion capacity, ton 200 main motor power, kW 90 Press weight, kg 110000

Central lubrication, oil circulation system, progressive pump, central lubrication unit -Drive motor: Siemens -Pump: 440 V 0.105 kW -Number: 1 x pumps available -Price: per piece -Dimensions: 290/180/H340 mm -Weight: 8.7 kg

Offer 23168 Specifications: - Notching options + mitres in 3 levels - right-angled, single-sided + two-sided + three-sided oblique. - Can be used as a slate-cutting cut-off saw - Pneumatic profile clamping machining with semi-automatic sawing units - Saw blade dimensions - vertical 500 x 3.5 x 40 mm positive - horizontal 500 x 3.5 x 40 mm negative - Notching width / notching height at 90° 300 / 285 mm - vertical saw blade 60° - 90° - 25° mot. Positioning with digital display - Swivel range saw blade horiz. With the vert. Saw blade - 45° - 90° - 45°, motorized positioning with digital displays - Notching height adjustment with digital displays - Profile stop shoulder manually swivel 30° - 90° - 45° - pneumatic coolant spraying device - Air connection 6 bar - Drive 400 V / 2 x 3 kW - Space requirement approx. W 2400 x H 2000 / D 1400 mm - We ...

- Eirich RV 19 granulation / mixing plant, mixer, feed hopper, riser plate completely refurbished. Incl. -Steel construction - Screw conveyors - Input silo approx. 30 m3 - Steep conveyor

ENGEL INSERT 200H/50 injection moulding machine was manufactured in 2007 in Austria. The machine with its small size and large capabilities is used for e.g. overmoulding of inserts and the joining of various materials such as glass, metal and electronics. Thanks to the combination of a clamping force of 50 tonnes and high-quality components, the injection moulding machine guarantees excellent quality of inserts and high repeatability. The machine’s sturdy, solidly built construction features a convenient and easy-to-use ENGEL CC 200 CNC controller for entering all possible process parameters, such as mould clamping force and speed. Once the parameters have been entered, the two halves of the mould are precisely closed, after which the vertical injection moulding machine ENGEL generates a high clamping force. The mould cavity is carefully filled with plastic under high pressure using ...

Tool grinding machine, grinding machine, angle grinding machine, rotary steel grinding machine, steel grinding machine -Grinding places: 4 -Angle tables on swing tables: 3 -Angle table for chip breaker groove: 1 -Quantity: 1 piece available -Dimensions: 1210/1210/H1450 mm -Weight: 536 kg

Bizerba CWL Eco flex continuous scale with Sick VMS520 volumetric measuring system Bizerba CWL Eco flex Continuous Scale Dynamic weight detection with volume determination The CWL Eco flex can be integrated almost effortlessly into existing parcel shipping, sorting systems and feeding lines. Bizerba WM-CWL flex Continuous Scale Model: CWL Eco in Motion DE-09-MI006-PTB018 Max 60 kg Min 0.4 kg 230 V Sick VMS520 volume measurement system Features • Non-contact, active measuring method • Measuring the length, width and height of cuboid objects • Measure the length, width and height of objects with almost any shape • Works with a wide variety of surface structures and on different flat conveyor systems • Flexible system configurations • Calculation of the small-envelope cuboid (box volume) • Calculation of the real volume Device components Sick ...

WILL NOT LAST Husky Hypet 300 P100/110 E100 year 2010 working hs approx 65.000 Condition In production Availability Immediate Auxiliaries Resin dryer with hopper and Mold dehumidifer Cavities 72 Mold YES 2925 water short 12g and 13g 3025 water long/milk 13g 14.5g 15.5g 17.5g ask for info and dont delay

table length: 1500 mm table width: 1500 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 0,8 t dimensions: 1,5 x 1,5 x 0,9 m Welding table SIEGMUND Professional Extreme 850 + plasma nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 850 Vickers. The table has a material thickness of approx. 24.5-27mm. The holes have a diameter of 28mm. Hole arrangement in 100 mm grid on the table top, parallel hole arrangement in 50 mm grid on the sides. Including basic equipment. Accessories shown are optional. Price plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Gear motor, electric motor, three-phase motor -Speed: 22 rpm -Power: 0.18 kW -Shaft: Ø 20 x 40 mm -Protection class: IP54 -Construction: B5 angle -Dimensions: 325/240/H155 mm -Weight: 9.8 kg

wire electrode, welding wire, welding wire -Manufacturer: Elga, started roll of inert gas wire electrode -Type: Cromacore DW-309L O1.2mm -Dimension: O 300 /105 mm -Weight roll: 5 kg

Wire electrode, welding wire, welding wire -Material: stainless steel -Manufacturer: Eurotrode, started roll of shielding gas wire electrode -Type: M 8820 1.4829 Ø 1.2 mm -Dimensions: Ø 300 / 100 mm -Weight roll: 5.1 kg

Max Machining Dimentions : 3200x1190x70 mm Min Machining Dimentions : 200x70x8 mm Drilling head 15 spindles include sawing unit in X direction Linear tool changers 6

Converter, converter, converter, drive converter, controller, inverter -SEW: Movitron Type 355 825074X -Input: E 380-415 V 50 (60) Hz -Output: G 0 ... 460 V 55 A -Temperature: 0-45 °C -Protection class: IP00 -Dimensions: 335/220/H175 mm -Weight: 7.2 kg

Connecting cable, connecting wire, cable line, socket cable, socket line, sensor line -Manufacturer: Murr Elektronik, M8 female 0° free lead end unused original packaging -Type: 7000-08041-2100500 -Mat-No.: Code 47218 -Package dimensions: 220/220/H10 mm -Weight: 0.2 kg