capping machine used for sale

bore capacity in steel (diameter): 16 mm throat: 170 mm bore stroke: 50 mm : 16 mm spindle taper: MK2 spindle turning speed range: 50 - 2250 U/min : 320 mm : 145 mm table surface area: 500 x 140 mm connected load frequency: 230 V total power requirement: 0,5 kW weight of the machine ca.: 90 Kg dimensions of the machine ca.: 0,5 x 0,45 x 0,84 m Drilling and milling machine with - variable spindle speed - Digital depth display - Left / right switch - Cross support - swiveling spindle head - Feeds via hand crank - Tool case with content but without digital display The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Deburring machine, pipe deburrer, bore deburrer, deburring device, brush deburring machine, wire brush -Manufacturer: wrt, deburring machine with base -Drive: 3.0 kW / 2800 rpm -Brush: Ø 250 mm -Shaft: Ø 80 x 110 mm -Dimensions: 660/430/H1200 mm -Weight: 101 kg

Key data: 406 mm, 584 mm

Inv. Num. : 9153 Type: DS-30SSY Producer: HAAS Created: 2015 Parameters: Hours: 3002 h Maximum turning length: 584.2 mm Maximum turning diameter: 406.4 mm Maximum turning diameter over bed: 807.7 mm X-axis travel: 317.5 mm Y-axis travel: 50.6 mm Travel Z-axis: 584 mm Maximum main spindle power: 14 kVA Maximum spindle speed: 4800 1/min Number of all tools: 24 pieces Spindle bore: 88.9 mm Weight: 7259 kg Equipment: Chip conveyor Pick-up spindle C-axis Bar Feeder Tool Alignment System System for removing parts after cutting Driven Axial Holder ER32 (Heimatec) Driven radial bracket ER32 (Heimatec) Holders for rotary tools, other holders and jaws

sheet width: 1000 mm plate thickness: 5,0 mm distance between columns: 1070 mm diameter of upper rolls: 130 mm total power requirement: 4,0 KW weight of the machine ca.: 1,15 t dimensions of the machine ca.: 2,55 x 0,65 x 1,1 mm - Electrically adjustable rear roller - Electrically adjustable lower roll (material clamping) - Digital readout for rear roller movement - Digital readout for lower roll movement (material clamping) - Hardened rolls - Conical rolling - Swiveling top roll - Brake motor - Emergency stop - Documentation - 400V The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 1000 mm y-travel: 300 mm z-travel: 400 mm table-size: 1320 x 360 mm spindle taper ISO: 40 spindle turning speed range: 58 - 1800 U/min total power requirement: 4 kW weight of the machine ca.: 2,3 t dimensions of the machine ca.: 2,1 x 2,1 x 1,95 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

width of the strips: 75 mm band length: 2000 mm band speed: 37 m/sec total power requirement: 3 kW weight of the machine ca.: 0,105 t dimensions of the machine ca.: 1,2 x 0,5 x 1,0 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

RAFAMET KCH 360/450 vertical turret lathe was built in 1987 in Poland by Fabryka Obrabiarek RAFAMET. The machine is used for precise machining of large and heavy workpieces whose size does not allow effective machining with standard machines. RAFAMET KCH 360/450 is distinguished by its stable design, equipped with two vertical supports and one side support. Machining is performed on a work table with a diameter of 3600 mm by means of a reliable vertical spindle. The work table offers 20-position speed adjustment in the range of 0.6 to 50 rpm, enabling precise adjustment of the parameters to the production requirements. The position of the head in all linear axes is continuously monitored by state-of-the-art SONY digital readout, which ensures high precision measurement. All this makes the offered KCH 360/450 vertical turret lathe an excellent choice for, among others, the energy, ship ...

Jig boring mill, fine boring mill, plate boring mill, table boring mill, boring mill, milling machine, -Table dimensions: 700 x 405 mm -Travel paths: Z 330 mm/Y 410 mm/X 630 mm -Quick stroke: 155 mm -Recording: MK4 -Speeds: 31 - 1500 rpm -Dimensions: 1570/1800/H2600 mm -Weight: 2600 kg

width of the strips: 25 mm band length: 762 mm dimensions of grinding wheel: 125 mm Table tiltable up to: 45 Grad table surface area: 130 x 130 mm connected load frequency: 230 V total power requirement: 0,3 kW weight of the machine ca.: 9 Kg dimensions of the machine ca.: 650 x 360 x 400 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding range: 2 - 20 mm sharp cornered angle min./max.: 90 - 135 Grad connected load: 230 V weight of the machine ca.: 8,6 Kg dimensions of the machine ca.: 0,35 x 0,2 x 0,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Remote control for inert gas welding device, inert gas device, welding rectifier, hand controller -Manufacturer: Fronius, remote control RCU5000i Univ.SD -Art.No.: 4,046,098 -Voltage: U1 24 V -Dimensions: 180/260/H50 mm -Weight: 1.5 kg

: 50 (500) mm : 45 (500) mm L-beam: 80 x 80 x 8 (800) mm T - beam - web outwards: 80 x 9 (800) mm Axis diameter: 60 mm work speed: 5,0 m/min Tool diameter: 195 mm total power requirement: 3 kW weight of the machine ca.: 1,0 t dimensions of the machine ca.: 1,2 x 0,9 x 1,2 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Counting and banding machine ATS US 2000 FSB-DBN-T; State as is; should be installed by ATS Customer Service; suitable for processing banknotes; Rontech MF-360 RAV counting feeder; 1x Banderolier ATS US 2000 AD bandwidth 40mm and frame 260x260mm; 1x Banderolier ATS US 2000 AD Bandwidth 30mmund Frame 260x120mm; Turning unit installed. Count and banding machine ATS US 2000 FSB-DBN-T; condition as is; should be installed by the support of ATS; used for banknotes; count feeder Rontech MF-360 RAV; 1x banding machine ATS US 2000 AD with band width 40mm and frame 260x260mm; 1x banding machine ATS US 2000 AD with band width 30mm and frame 260x120mm; turning station.

width of the strips: 100 mm band length: 1220 mm band speed: 1140 m/min. : 0,62 x 0,4 x 0,35 cm total power requirement: 1,5 kW weight of the machine ca.: 0,04 t dimensions: 0,97 x 0,67 x 0,37 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

faceplate diameter: 3200 mm swing diameter: 3500 mm turning height: 2200 mm Control: Typ 840 D sl total power requirement: 51 kW weight of the machine ca.: 86 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 800 mm y-travel: 500 mm z-travel: mm Control: Heidenhain tool taper: SK 40 : 13,5 kw turning speeds: 3150 U/min total power requirement: kW weight of the machine ca.: 3 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Multifunctional punch, punch press, hole punch, pneumatic hole punch -operated: pneumatically -Year of manufacture: 1995

turning diameter: 630 mm turning length: 2000 mm control: Zyklen gesteuert steady: 2 Stk. total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 700 kN injection volume: 103 cm³ screw diameter: 30 mm platen size: 432 x 310 mm closing stroke: 650 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: -- kN injection volume: 230 cm³ screw diameter: 40 mm platen size: 475 x 475 mm Condition: used, Specification: Horizontal injection moulding machine, injection unit: - Screw diameter: 40 mm - Cylinder diameter: 40 mm - Spraying volume: 230 cm³. Clamping unit: - tie bar distance: 475 x 475 mm - Operating hours approx.: 30000 h - Air valve - Core pull - 12-way hot runner controller The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Super clean 1993 Bridgeport EZ trak SX 2 axis mill. Machine is in very nice condition. It has none of the usual battle scars from use and appears to have been used very little. The control boots up as it should and both axis motors work smoothly. SPECIFICATIONS: Capacity 9" x 48" Table Size 9" x 48" Longitudinal Travel 30" Cross Travel 12" Vertical Knee Travel 16" Spindle Speeds (Variable) 60-4200 RPM Spindle Taper R-8 Spindle Quill Travel 5" Positioning Speed (X-Y Axis) 100 IPM Feed Rate (X-Y Axis, Variable) 0.1-100 IPM Spindle Quill Feeds (3) 0.0015" - 0.003" - 0.006" Ram Travel 12" Distance, Table To Spindle Nose 2 1/2" - 18 1/4" Throat Distance 6 3/4" - 18 3/4"

x-travel: 600 mm y-travel: 400 mm z-travel: 420 mm Control: Heidenhain Tnc table-size: 900 x 460 mm turning speeds: 4000 U/min total power requirement: kW weight of the machine ca.: 2,9 t dimensions of the machine ca.: 3 x 2 x 2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 4200 kN injection volume: 572 - 1716 cm³ screw diameter: 90 mm platen size: 1040 x 1040 mm closing stroke: 620 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: -- mm cross-section heigth:: -- mm feed:: -- mm speed of feed:: 0,4 - 20 m/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 85 mm cross-section heigth:: 25 - 40 mm feed:: 1 - 999,999,9 mm speed of feed:: 60 m/min cuts max.:: 100 - 120 Schnitte/m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 5 Schläuche 3-5 mm cross-section heigth:: 3 - 20 mm feed:: 1,5 - 50 mm Condition: used, very good condition only approx. 1 year in production Specification: circular knife cutting machine for slices and rings - small cutting machine with high-speed rotating circular knife - feed and knife movement, pneumatic - Tube or strand diameter min.: 3 mm - Tube or strand diameter min.: 20 mm - Feed (ring or strand length): 1.5 - 50 mm - Output depending on material max.: 60 strokes/min - Optionally, the following can be cut 5 tubes or strands: diameter 3 mm to 5 mm 4 tubes or strands: diameter 5 mm to 7 mm 3 hoses or strands: diameter 7 mm to 12 mm 2 hoses or strands: diameter 12 mm to 15 mm 1 hose or string: diameter 15 mm to 20 mm - Power requirement approx.: 0.37 kW - Air supply min.:  ...

max. wheel diameter: 275 mm gear width: 55 mm max. module: 6 min. module: 1,5 control: Sinumerik 840C tooth width: 5,5 mm spiral angle: 0/60 ° max. number of teeth: 120 min. number of teeth: 5 transmission ratio max.: 1:10 transmission ratio min.: 1:1 spindle speeds: max. 110 mm blade head turning speeds: 20-110 1/min total power requirement: 100 kW weight of the machine ca.: 16700 kg dimensions of the machine ca.: 5200x2300x2400 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CNC Cutting, Drilling, Nesting, and Milling Capabilities H10 Spidle Head 3-Axis Capabilities Dual Becker Industrial Vacuums Automatic Tool Length Measuring System Low Maintenance Bridge Design w/ Gantry Drive 28 Spot Linear Tool Holder Includes (20) Different Tool Heads 10" and 6" Suction Tubes Dual 24" Control Monitors Label Maker and Printer Includes Auto Voltage Transformer Software License Not Included Specifications Model Year: 2016 Processing Table Size: 146" x 61" Finish Table Size: 152" x 61" Max Motor Power: 10 kW Motor Speed: 24,000 rpm Tool Holder Places: 28 Number of Tool Heads: 20

: 0 bore depth: 10000 mm number of spindles: 0 Control: Siemens Simatic Touch SPS swing over bed: 1050 mm swing diameter over bed slide: 1600 mm boring diameter: 50 - 310 mm centre height: 800 mm speeds:: 2,5 - 400 total power requirement: 74 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: siehe TD mm pressure: siehe TD t total power requirement: 4 kW weight of the machine ca.: 0,950 t dimensions of the machine ca.: 900 x 1050 x 1300mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Transpak TP 6000 Professional strapping machine from a renowned manufacturer, designed for high speed and trouble-free operation. -Up to about 30 straps per minute. -Frame inner dimensions approx. 850 x 600 mm. -Firm strapping by 12 mm tape. -Automatic belt forwarding and belt return. -Strap tension adjustable. -Triggering: strapping via hand button or foot switch or alternatively automatic mode selectable (sensor in the table top). -Uncomplicated and ergonomic bobbin changing and threading system. -Designed with ergonomic roller conveyors on the table surface. -Working height approx. 820 mm. machine can be moved via castors. The machine can be demonstrated under power.

bore capacity in steel (diameter): 23 / 28 mm throat: 260 mm bore stroke: 120 mm tool taper: MK 3 table-size: 500 x 350 mm column diameter: 100 mm total power requirement: 1,3 kW weight of the machine ca.: 400 kg dimensions of the machine ca.: 800 x 600 x 1750 mm Defective feed! Right-left rotation stepless speed adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Professional strapping machine from a renowned manufacturer, designed for high speed and trouble-free operation. -Up to about 30 straps per minute. -Frame inner dimensions approx. 850 x 600 mm. -Firm strapping by 12 mm tape. -Automatic belt forwarding and belt return. -Strap tension adjustable. -Triggering: strapping via hand button or foot switch or alternatively automatic mode selectable (sensor in the table top). -Uncomplicated and ergonomic bobbin changing and threading system. -Designed with ergonomic roller conveyors on the table surface. -Working height approx. 820 mm. machine can be moved via castors. The machine can be demonstrated under power.

screw size: 98 mm injection shot weight in Polysterol: unbkt. g/PS closing pressure: 8600 kN total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mm plate thickness: siehe TD mm pre-bending: siehe TD total power requirement: 11 kW weight of the machine ca.: 4,450 t dimensions of the machine ca.: 3830 x 1160 x 1180 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mm plate thickness: siehe TD mm pre-bending: 24mm total power requirement: 45+22 kW weight of the machine ca.: 43 t dimensions of the machine ca.: 6684 x 2280 x 2375mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mm plate thickness: siehe TD mm pre-bending: 25mm total power requirement: 37 kW weight of the machine ca.: 20,5 t dimensions of the machine ca.: 5560 x 2060 x 2050mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: unbkt mm double T-iron on the x-axis: unbkt. mm U-iron on the x-axis: unbkt. mm total power requirement: 37 kW weight of the machine ca.: 16 t dimensions of the machine ca.: 2900x2300x2150 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Professional strapping machine with internal frame dimensions of approx. width 850 x height 600 mm from a renowned manufacturer, designed for high speed and trouble-free operation. Equipped with an ergonomic and uncomplicated bobbin changing and threading system. -Equipped with ergonomic casters on the table surface. -Strapping release alternatively possible by hand switch or table photocell (automatic operation). -Up to approx. 20 straps per minute. -Band width 12 mm. -Strap tension infinitely adjustable. -Fully automatic tape threading and tape penetration monitoring. -Closure type: Welding in the heating wedge method. -Electronic temperature control. -The machine can be moved via castors. The machine can be demonstrated under power.

angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: 15 kW weight of the machine ca.: 4,6 t dimensions of the machine ca.: 1850 x 1550 x 1685mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mm plate thickness: siehe TD mm pre-bending: 35mm total power requirement: 45+22 kW weight of the machine ca.: 35 t dimensions of the machine ca.: 5684 x 2280 x 2375mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mm plate thickness: siehe TD mm pre-bending: 40mm total power requirement: 2x37+30 kW weight of the machine ca.: 45 t dimensions of the machine ca.: 6085 x 2630 x 2787mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mm plate thickness: siehe TD mm pre-bending: 50mm total power requirement: 45+45 kW weight of the machine ca.: 72 t dimensions of the machine ca.: 6370 x 3240 x 3660mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: siehe TD mm plate thickness: siehe TD mm pre-bending: 10mm total power requirement: 15 kW weight of the machine ca.: 10,6 t dimensions of the machine ca.: 5310 x 1660 x 1590mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

MIG/MAG welding machine, MIG/MAG welding machine -Max. welding current: 320 A -2-roller drive -Air-cooled -incl. ground cable -with removable wire feeder -Gas valve -Hose package -Dimensions: 1000/500/H970 mm -Weight: 170 kg

Working areaTurning diameter500 mmDistance between spindles1435 mmMax. Turning Length1100 mmGeneralTurning/milling center with turning length 1100 mm - mounting HSK-A 63 DIN 69893 - B-axis ±120 - Y-axis ±100 mm - 60-fold chain magazine - Absolute, direct path measuring systems in X-, Y- and Z-axis - Hydraulically movable tailstock with foot pedal - Double switch filter - Electric handwheel - DMG MORI IoT connector - Clamping pressure adjustment on the control - 5-axis simultaneous machining; Control: CELOS X with Siemens SINUMERIK ONE Main drive 1Drive power (100% DC)14 kWDrive power (40% DC)17 kWSpeed range- 5000 rpmTorque (100% DC)275 NmMax. torque (40% DC)345 NmTurning-milling spindleSpindle taperHSK-A 63 DIN 69893 Spindle speed-15000 rpmDrive power (40% DC)22,5 kWDrive power (100% DC)19 kWTorque (100% DC)85 NmTorque (40% DC)120 NmFloor space/WeightDimensions (L x W x H)5,77 x 2,33  ...

AGIE CHARMILLES FO 350SP die-sinking EDM was built in 2013 in China by Beijing Agie Charmilles Co., Ltd. The machine is in very good condition, fully operational and regularly serviced throughout its service life. The AGIE CHARMILLES FO 350SP is used in the production of precision tools, moulds, dies or punches. The machine uses an electrical erosion method that enables complex shapes to be made in even the hardest materials. This method also minimises or completely eliminates the need to undertake additional finishing processes, such as polishing. The machining process is performed in a dielectric-filled work tank. The use of dielectric increases the surface quality and dimensional accuracy of the workpieces, and its level and working pressure are continuously monitored by an advanced measurement system. The work table, in turn, has T-slots for fast and easy clamping of workpieces. A ...

sheet width: siehe TD mm plate thickness: siehe TD mm pre-bending: 25mm total power requirement: 30 kW weight of the machine ca.: 15,15 t dimensions of the machine ca.: 5010 x 2060 x 2050mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.