129,241 used machines on RESALE, but how to find them? Machine Search
SPECIFICATIONS: Table size: 2400 x 900 mm Extendable table 1 4-roller drive (with variator) Installed power: 5 kW Lockers Ø 35 mm Motorized spindle tilt +/- 45° Motorized height adjustment Dornfix clamping system
SPECIFICATIONS: Feed length: 1970 mm Working width: 230 mm Working height: 120 mm Spindle: Ø 40 mm Number of Spindles: 5 Direct drive / cardan (0.25 kW x 3 motors) Speed: 6000 rpm Installed power: 22.9 kW Voltage: 380 V Spindle configuration: I Bottom (4 kW) II Right - Left (7.5 kW), Left equipped with electronic control III Top (5.5 kW) equipped with electronic control IV Bottom (4 kW) EQUIPMENT: Complete with tools
SPECIFICATIONS: Feed length: 1970 mm Machinable width: 230 mm Machinable height: 120 mm Spindle: Ø 40 mm Number of Spindles: 6 Shaft drive (4 kW) Speed: 6000 rpm Installed power: 43 kW Equipped with ATS system for automatic adjustment Voltage: 380 V SPINDLE CONFIGURATION: I bottom (5 kW) II right (11 kW) III left (11 kW) III above (11 kW) IV top (5.5 kW) VI bottom (4 kW) EQUIPMENT: Complete with tools Accessories CE
SCM T130E spindle moulder Spindle diameter 40mm Overall length of spindles 180mm Spindle speed variable by inverter up to 10,000r.p.m Main motor power 7.5kw Spindle rotation right and left Electronic spindle height adjustment Electronic setting of fences Electronically adjustable roller feed 4-roller feed Maggi Variosteff 4 Feed speed control via variator CE Certified DTR documentation Year of production 2004
A Ferromatik Milacron injection molding machine without additional and peripheral equipment is available. Clamping force: 1000kN, injection pressure: 2000bar, stroke volume: 254cm³, heating capacity: 14.8kW, tie bar distance: 508mm, machine weight: approx. 6750kg, operating hours: approx. 33649h. On-site inspection is possible.
Two Battenfeld injection molding machines are available. 1) Battenfeld BA 1600, year of construction: 2001, clamping force: 1600kN, tie bar distance: 520mm/520mm, installation height min./max.: 225mm/550mm, opening stroke: 480mm, centering diameter: 160mm, screw diameter: 50mm, injection weight: 520g. 2) Battenfeld BA 500/200 CDK, year of construction: 1995, clamping force: 500kN, tie bar distance: 320mm/320mm, platen dimensions X/Y: 490mm/490mm, installation height min./max.: 150mm/350mm, opening stroke: 250mm, max. platen distance: 600mm, screw diameter: 35mm, injection volume: 134.7cm³, injection weight: 122.5g, injection pressure: 1484bar. Machine dimensions X/Y/Z: approx. 3800mm/1350mm/1800mm, weight: approx. 3200kg. The machine has cylinder problems with the screw and the forward/backward unit. Documentation available. On-site inspection is possible. Individual sale possible.
Spindle moulder with tilting shaft SCM mod. T110I - CE -Volt. 400/50 - Matr. AB/118120 - Year 1998
SAC SUERI fixed shaft spindle moulder mod. TS110 - CE compliant - Extended 2400 mm plates. -Volt. 400/50 - Matr. 9813 - Year 1998 - M42 - Complete with manual and CE declaration
WEINIG 5-spindle moulder mod. PROFIMAT P23E – CE compliant -Composition: - Oriz. Inf. 5.5Kw -Vert. right/left 7.5Kw - Oriz. sup. 7.5Kw - Oriz. Inf. 4 Kw - Width 230mm - ATS system - Year 1997 (CE)
WEINIG 5+1 spindle moulder mod. PROFIMAT 23 FORTEC - CE compliant - Complete with ATS device - 1st lower horizontal shaft - 2nd vert. Dx - 3rd vert. Sx - 4th upper horizontal - 5° lower horizontal - 6th universal - Width 230 mm. - Cardan drive - Year 2002
Key data: 3200 kN, 359 g/PS, 50 mm
1.0 St. gebr. Two-component injection molding machine Manufacturer: ARBURG Type: 720A3200-800/70 Year of Make: 2017 Clamping force: 320 tons Spar spacing 720 x 720 mm Installation height min./max.: 300 - 800 mm Opening travel: 600 mm Screws DN 1: 50 mm Max. displacement: 392 cm³ Moulded part weight in hp: 359 g Screw DN 2: 22 mm Max. displacement: 34 cm³ Moulded part weight in hp: 31 g Control: Selogica Request technical equipment.
Press force: 1100kN, screw diameter: 35mm, injection weight: 140g, stroke volume: 154cm³, injection pressure: 2429bar, max. barrel temperature: 375°C, weight: approx. 8000kg, control: MC 5 3.0, operating hours: 25271h, pump hours: 29098h. Including one linear robot KM LRX 150, travel X/Y/Z: 900mm/1200mm/3000mm, load capacity: 15kg. Documentation available. On-site inspection is possible.
Stretch blow moulding machine from EtekISBM Line = Injection stretch blow moulding Stretch blow moulding machine for disposable PET bottles made from PET preform blanksStretch blow moulding machine for production in rotary transfer processManufacturer: ETEK / GF-Industries Type Supra 800 sv 1Serial number: 22000225Year of construction: 2012Power: 90 kWNet connection: 400 volts, 50 HzNet weight approx. 6000 kgas good as new; used
Two complete injection molding plants with two Husky injection molding machines, four complete moulds with all-metal separator, Motan gravimetric mixing system and crane system are available. 1) 2x Husky H-PET230 AE RS95, year of manufacture: 2015, max. shot weight: 2424g, max. PET throughput: 390kg/h. 2) 48-cavity H-PET mold, preform weight: 17.8g, length: 89.35mm, wall thickness: 3.06mm, base thickness: 2.30mm, cavities: 48, cycle time: 12.1s-12.7s. 3) 48-cavity H-PET mold, preform weight: 30.26g, length: 122.3mm, wall thickness: 3mm, base thickness: 2.3mm, cavities: 48, cycle time: 14.4s-15s. 4) 32-cavity H-PET mold, preform weight: 18g, length: 82.04mm, wall thickness: 2.7mm, base thickness: 2.2mm, cavities: 32, cycle time: 11s-11.7s. 5) 32-cavity H-PET mold, preform weight: 29g, length: 108.59mm, wall thickness: 3.16mm, base thickness: 2.42mm, cavities: 32, cycle time: 13.4s-14s. To ...
Weinig Quatromat 23 Moulder Specifications: Brand: Weinig Type: Q23P (profileerautomaat) Year of Make: 2003 M-No.: 99567 Feed table: 2000 mm Dressing table adjustment range: 10 mm Joining ruler adjustment range: 10 mm Planing width: 13 - 230 mm Planing thickness: 6 - 120 mm Thickness adjustment: Manuel with Siko counter Width adjustment: Manuel with Siko counter Head dimension: Min. 613mm, up to max. 120230mm Knife shafts: Bottom: ø125 mm Right & Left: ø125-200mm Top: ø125-200 mm Adjustment range dressing shaft: 5 mm Spindle adjustment range axial: 30 mm Min. Product Length: Short Workpiece Length Equipment Central Control: Relay Control Lubrication: Spindle arrangement: Bottom 4.0 KW Right + Left Spindle 5.5 kW Above 4.0 kW Speed: 6,000 rpm Feed: 8 m/min Stepless -1.5 kW Steel and rubber rollers. 1 feed roller electro-pneumatically cycled ...
1 piece new, S 80/24D, for PUR 1 piece little used, S 80/24D, with maddock and mixed part
overhauled in 2012 and equipped with a new Beckhoff control system with touchscreen. Extruder S 50/22D for HDPE single head with Moog servo valve and WDS. Steffes lekstester is there. Very good condition. Available from stock immediately, subject to prior sale
Extruder S 45/22D. Single head, machine can also be equipped with double or triple head. With external leak tester. Very good condition
Extruder S 36/22D. Double head, can also be supplied with single or triple head. Good condition
Extruder S 50/22D, Doppelkopf 100 Stich. Machine can also be equipped with single or triple head. Good condition
Extruder S 45/22D. Double head 70mm stitch, machine can be equipped with single head. Good condition
Extruder S 55/22D. Single head with WDR. With Beckhoff control and touch screen. Very good condition
Two injection moulding machines Krauss Maffei are available. 1) Krauss Maffei KM 50 C1, year of manufacture: 1999, injection unit: SP220, screw diameter: 30mm, L/D ratio: 23, injection pressure: 2500bar, shot volume: 85cm³, machine dimensions X/Y/Z: approx. 3200mm/1350mm/1800mm, weight: approx. 2500kg, control: MC4, operating hours: approx. 86000h. 2) Krauss Maffei KM 125 C1, year of manufacture: 2000, injection unit: SP520, screw diameter: 45mm, L/D ratio: 20, injection pressure: 1878bar, shot volume: 217cm³, machine dimensions X/Y/Z: approx. 4500mm/1550mm/2200mm, weight: approx. 5500kg, control: MC4, operating hours: approx. 82000h. Documentation available. An on-site inspection is possible.
A two-component injection moulding machine Engel with piggyback configuration, including Engel Viper 40 robot and safety enclosure, is available. Clamping force: 1800kN, nozzle diameter: 35mm, min. mould installation height: 270mm, max. platen distance: 1020mm, tie bar spacing: 980mm, centering: 180mm. Screw diameter 1/2: 22mm/15mm, injection pressure 1/2: 2392bar/2203bar, injection weight 1/2: 66g/19.5g. Robot year of manufacture: 2014, robot travel X/Y/Z: 700mm/1300mm/2360mm. Machine dimensions X/Y: approx. 6700mm/2100mm, control: CC400, operating hours: approx. 38567h. The 22mm screw needs to be replaced. Without conveyor belt. Documentation available. An on-site inspection is possible.
Universal table router FZ0 from Zimmermann Model milling machine with adjustable Bosch motor GGS 27 LC Ideal for use in model making and mould making. Drive motor 230Volt, 0.6kW Spindle speed adjustable approx. 12000 to 27000 rpm Machine table approx. 590 x 420mm Unit swivel on both sides up to 90 degrees Longitudinal stop with fine adjustment Extraction hood and protective hood Collet holder 6mm and 8mm Including the milling cutters and burrs shown With lockable base cabinet, 2 drawers and a door, key provided The base cabinet was provided by the previous owner with an aluminum sheet over angles, which offers an integrated extraction option, see photos Waldmann surface-mounted lamp with attached magnifying glass Original paint, dabbed in places CE mark Very well maintained machine from prototype production in the motorsport department of a Wolfsburg car manufac ...
Two injection moulding machines are available. 1) Ferromatik K 110 1100-493, year of manufacture: 2000, clamping force: 1100kN, min. mould installation height: 300mm, max. opening stroke: 550mm, screw diameter: 40mm, injection volume: 201cm³. The control no longer starts up properly, probably due to the circuit board. Includes a 3-axis handling robot Remak. Without conveyor belt. 2) Arburg 270 M 500-90, year of manufacture: 1995, clamping force: 500kN, min. mould installation height: 225mm, max. opening stroke: 325mm, screw diameter: 30mm, injection volume: 70cm³. The cylinder is slightly leaking. Documentation available. An on-site inspection is possible.
Clamping force: 1500kN, screw diameter: 50mm, tie bar spacing: 500mm, platen dimensions X/Y: 780mm/790mm, opening stroke: 600mm, daylight: 900mm, ejector stroke: 150mm, shot volume: 305cm³, injection weight: 278g, injection pressure: 2336bar. Machine dimensions X/Y/Z: approx. 4700mm/1550mm/2200mm, weight: approx. 7000kg, control: MC4. Includes Sepro handling system. Documentation available. An on-site inspection is possible.
Clamping force: 220kN, min. mould height: 200mm, max. opening stroke: 200mm, max. platen distance: 400mm, ejector stroke: 80mm, machine dimensions X/Y/Z: approx. 2600mm/800mm/1600mm, weight: approx. 760kg. An on-site inspection is possible.
ARBURG 221 M 250-55 injection moulding machine. Clamping force 250 kN Year of construction 1996. Machine does not work. It is sold in the state as is, perhaps with its defects we don't have the skills to diagnose. It is complete, likely that repair is needed, or for replacement parts.
SCM T150 spindle moulder Spindle diameter 35mm Overall length of spindles 180mm Electric spindle lift Electric fence passage Electrically adjustable angle -10/45 Spindle speed variable 3000-4500-6000-7000-10000r.p.m 5.5kw motor DTR documentation Net price
Used Revised Sipa Rotary Blow Molding Machine 2008: A Comprehensive Overview Are you in the market for a reliable blow molding machine? Look no further than the used Sipa Rotary Blow Molding Machine 2008. In this article, we will delve into the details of this machine, exploring its features, specifications, and benefits. Whether you are a seasoned professional or just starting in the industry, this article will provide you with valuable insights into the Sipa SFR8. 1. Introduction Blow molding machines play a crucial role in the production of various plastic containers. The Sipa Rotary Blow Molding Machine 2008, also known as the SFR8, is a popular choice in the industry. It offers efficiency, precision, and versatility, making it an excellent investment for manufacturers. Let's explore its features in detail. 2. Overview of the Sipa Rotary Blow Molding Machine 2008 The Sipa Ro ...
An almost like-new injection moulding machine Arburg is available. Clamping force: 1600kN, tie bar distance: 520mm, clamping stroke: 364mm, ejector stroke: 150mm, ejector force: 40kN, injection unit: 400, injection pressure: 2500bar. Machine dimensions X/Y/Z: approx. 6000mm/1800mm/2200mm, weight: approx. 6000kg, control: Selogica, operating hours: approx. 67h. Includes enclosure with clean air supply FilterFanUnit and removal robot. Documentation available. An on-site inspection is possible.
HESTA HK 453 Year of manufacture 2002 - completely overhauled in 2021 Extruder 45 mm, 22 D Control Beckhoff New quill head, a new wall thickness control and new hybrid pump Denison The machine has been in operation for less than 50 hours since the overhaul in 2021, and in almost mint condition.
SPECIFICATIONS: Feed length: 1970 mm Machinable width: 230 mm Machinable height: 110 mm Spindles: Ø 40 mm Number of Spindles: 4 Shaft drive Installed power: 16 kW Voltage: 380 V Spindle configuration: I bottom: 3.7 kW II right: 5.5 kW III left: 5.5 kW IV: top: 5.5 kW
Overview The BLOMAX 4 blow molder was manufactured by the German company SIG Corpoplast (now KHS) in 2006. It has been overhauled by a machine builder and can be inspected in dry operation. Blow molds are not included, but can be obtained. Technical details Output: up to 7,200 bph 4 cavities Dimensions: 4960 mm x 3900 mm x 3000 mm Weight: 15 t Operating hours: 44.736 Bottles Volume: 200 ml - 2000 ml Max. Diameter: 115 mm Max. Length: 350 mm Preforms Length: 60 - 200 mm Max. Support ring diameter: 35 mm Scope of delivery Blow molder is completely equipped with the system for preform feeding (silo, elevator, sorting, chute)
SIDEL SBO10- blowing machine, SBO10 is intended to manufacture PET bottles. Its production rate can be up to 10.000 bottles per hourdepending on the capacity., As first step, the operator puts the preform bin, via trans pallet or forklift, in the hoisting and tipping unit (SAMETO brand) and the preforms inserts in the hopper., After that, the elevator transfers the preforms to the horizontal elevator, the unscrambler and the final gravity guide (infeed rails).The below schematic diagram describes the general process of SBO10 machine:, which consists of:, 1. Preform infeed rails, 2. Preform infeed wheel, 3. Infrared oven, 4. Preform transfer wheel, 5. Blow wheel, 6. Bottle transfer wheel, 7. Bottle evacuation, GENERAL Presentation, 1. Infeed of cold preforms, Cold preforms are inserted by an inclined ramp. They are hung by the neck and are guided by two rails between which they are lowere ...
SPECIFICATIONS: Machine inlet: 1970 mm Working width: 230 mm Working height: 120 mm Spindles: Ø 40 mm Number of Spindles: 6 Shaft drive Installed power: 38 kW Voltage: 380 V SPINDLE CONFIGURATION: 1: bottom (4 kW) 2-3: right-left (11 kW) 4: top (7.5 kW) 5: bottom (5.5 kW) 6: universal (5.5 kW) EQUIPMENT: Miscellaneous Accessories
Eight Arburg injection molding machines, one Engel injection molding machine, and one Demag injection molding machine are available. 1) Arburg 270M 350-90, year of manufacture: 1996, operating hours: approx. 110000h. 2) Arburg 270M 350-90 U, year of manufacture: 1998, operating hours: approx. 108000h. 3) Arburg 270M 350-90, year of manufacture: 1992, operating hours: approx. 178000h. 4) Arburg 420C 1000-250, year of manufacture: 1995, operating hours: approx. 96000h. 5) Arburg 370C 800-225, year of manufacture: 1992, operating hours: approx. 156000h. 6) Arburg 320M 500-90, year of manufacture: 1991, operating hours: approx. 94000h. 7) Arburg 270M 350-90 U, year of manufacture: 1998, operating hours: approx. 83000h. 8) Arburg 630S 2500-675, year of manufacture: 2003, operating hours: approx. 93000h. 9) Demag Viva 100-400, year of manufacture: 1999, operating hours: approx. 116000h. 10) En ...
SPECIFICATIONS: Feed length: 1980 mm Working width: 220 mm Working height: 120 mm Spindle: Ø 40 mm Number of Spindles: 8 Shaft drive (7.5 kW) Installed power: 64 kW Voltage: 380 V SPINDLE CONFIGURATION: 1: bottom (5.5 kW) 2: right (5.5 kW) 3: left (5.5 kW) 4: right (5.5 kW) 5: top (7.5 kW) 6: bottom (7.5 kW) 7: top (11 kW) 8: bottom (7.5 kW) EQUIPMENT: Complete with accessories
An Arburg injection molding machine with integrated rotary table is available. Connected load: 61kW, clamping force: 500kN, opening force: 40kN, opening stroke: 250mm, max. mold installation height: 270mm, platen distance: 520mm, rotary table diameter: 900mm, rotation angle: 180°, max. table load: 240kg, max. injection pressure: 2500bar. Machine dimensions X/Y/Z: approx. 3250mm/2000mm/2600mm, weight: approx. 3200kg, operating hours: 6244h. Documentation available. An on-site inspection is possible.
MARTIN Swivel milling machine, type T 23, built in 1978, swivel range: -5 to 45°, spindle diameter 30mm, speeds: 4, height adjustment: handwheel, motor: 6 kW, table dimensions 1,100 x 940 mm, swivel adjustment handwheel
Height=1.612 m, Overall length= 1.127 m, Overall width= 0.75 m, Description Belt rounder for rye bread Used in good working condition
Injection moulding machine for food and beverages caps
Injection moulding machine for PET preforms
Clamping Force: 150 ton // Mould Height (Max): 730 mm
Injection moulding machine for food and beverages caps
Injection moulding machine for PET preforms
Injection moulding machine for PET preforms
Container Size (Max.): 2,5 l
maximum number of results exceeded
please refine your search
