We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
120,835 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
1 x Werner & Pfleiderer 400mm dia dump extruder, Type: EAE400, Fabrik nr 221284, Werk nr 416295, Year: 1985, double hydraulic crammer feed, feed section 965mm wide, L/D ratio 8:1, with 235kW DC variable speed motor, Sheeting head to produce up to 1000mm wide sheet. Complete with controls and hydraulics etc.
1 x Francis Shaw 45mm dia coldfeed rubber extruder, M/c no. 4513, Year: 1992, power roll feed, L/D ratio 15:1, hinged straight head with c\clamp, cored scred + jacketed barrel with built in temp control unit. Complete with control panel and in very good condition. Box of dies included.
used
Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.
used
Used Troester rubber extruder type GSV 60/k-12-18 D with feed roll can be modified/overhauled according to customer\s specification, with or without vacuum, year of construction: 1991 machine was in operation until end of 2010. including feed roll, new drive with flat-gear motor screw speed: maximum 62 rpm motor power: 22 kW PLC control and TCU can be renewed, if requested.
Iddon Cold Feed Extruder. 2.5" screw dia. 10/1 LD Ratio. Motor Size 20.4/5.5 HP
used
Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.
used
Extrusion press with 400 mm Ø, 55 kW drive, hard cast screw and pre press PZSVG 40 (built 1996, 15 drive), on 4 hydraulical posts. Complete, incl. 1 set spare parts (replacement screw and windlass).
used
1 x Buss PR200? Ko-Kneader, supplied fully refurbished by Buss in 1995, G130 gearbox, 11 L/D ratio, with 340kW dc motor and controls. Including oil heater and TCU 2t/hr output. Spare screw and barrel segments.
1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.
used
Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel
used
Barwell C3 Preformer Extruder 2500 psi Output 600kg/hour Ram type Extruder Extruder size 250mm With Rotary Cutter 8 fixed speeds Year 1980
new
Single-screw extruder with new 7,5kW drive, new gear box, new cylinder and new screw 30 mm - 28 d, nitrated new ceramic heating elements, cooling fan, temperature sensors Control cabinet integrated in the machine frame Machine frame on wheels Stainless steel hopper
new
Plant for the production of filament for use in 3D printers Capacity up to 10 kg/h consisting of 30 mm extruder, stainless steel trough, puller and winder with traverse guide
used
According to the description below
used
Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.
used
Extruder KE 90 x 30-D for manufacturing of von TPE foam and compact profiles screw diameter: 90 mm L/D ratio 30:1 (2700mm) extruder with 11 temperature-controlled zones (electrically heated by fluids) Siemens electric drive, motor 45kW at 2500rpm year of construction 1996, machine in very good condition (preliminary used in test operations) melt application device (gear pump) double profil head (also used for extrusion-coaded framework belts) electric equipment partially available extruder mounted on movable baseplate
new
We´re offereing successfully since many years twin-screw compounding extruders >> NEW segmented screws and cylinders, LD ratio due to your request Side-feeders, vacuum ports and accessories Please contact us for further information
used
New and unused machine Berstorff twin screw extruder ZE 130A Extruder screws: 2x140 mm L/D 30:1 Built: 1988 (unused) Drive: DC motor - 250 kW Screw rotations: 300 rpm Extruder heating: 70 kW 2x Degassing complete screw in original packaging 2 machines available Location Germany, Wuppertal Visit possible, appointment by appointment
used
Used EXTRUDER twin screw (TWIN SCREW EXTRUDER) for the production of cereal flakes: Producer: PAVAN Model: TT92 Year: 2002 Dimensions: 6580 x 4150 x 3000 Weight: 2400 kg Productivity: 500 kg / h Power: Description: A twin-screw extrusion device as a result of a continuous and automatic process of a great variety of flour and cereal starches / tubers, both mixed and pure. The materials from the dispensing unit are pre-mixed using a suitable device equipped with counter-rotating blades (double shaft mixer), and then enter the mixing tank for kneading and homogenization. From the mixing tank, through a suitable screw device (forced supply), the mixture is pressed into a group of cooking cylinders in which the cylinders are heated to the desired stage, according to a predefined and automatically controlled temperature profile. compatibility of extruder screws, which are repla ...
used
Food Extruders single and twin screws for various applications : breakfast cereals, corn flake, pet food, full fat soya, snacks We overhaul many models and have in our stocks machines like Clextral BC 45/82, wenger 175 ... also walter single screw. Milin Gentieg cereals Britany, France processing equipments has been specialising for years. We organise deliveries to any destinations for single machines or complete lines from cleaning to flaking and extrusion
used
Material: PE, PP, PS, ABS / Details: DC motor 220 kW, degassing, dcrunner, screw diameter 70 mm, LD: 32, Throughput: approx. 400 - 600 KG/hr.
used
EDI Autoflex Extrusion Die width 900 mm.
used
Multiple extruders
used
Strainer Bandera 150mm with 75kW motor. This machine has been overhauled by Deguma and little used after that. More info as attachment.
used
Single-screw rubber extruder with feed roller and degassing in screws of 70mm and a process length of 22.D - with two-speed temperature-controlled entagling screw - Degassing cylinder with device for static and/or vacuum degassing of the material - a vacuum block pump - two water temperature control units with 9kW heating capacity each, - a Siemens SPS S7 machine with Siemens KTP1200 HMI control panel - a directly driven feed roller feeder for rubber raw strips, a funnel-material stiffening system with Strip monitoring - temperable base body for tool holder and v.m
used
Farrel Twin Screw / Rollerdie Extruder complete available with Motor and Inverter Description attached!
new
Furnace 1200 temperature range 100 - 1200 Celsius inner dimensions 1x1x2m power 50kW PLC could be various size industrijskih peći INDUSTIJSKIH PECI NIKOTIRANJE CEMENTIRANJE TERMIČKA OBRADA ČELIKA KALJENJE INDUKCIONO PLAMENO ALATNIH I KONSTR. ČELIKA ŽARENJE MEKO NORMALIZACIONO STABILIZACIONO CNC obradni centri za struganje Završno precizno struganje Brušenje nakon termičke obrade, Zatvaranje tolerancija - lanci mjera, Kombinovani postupci struganja i glodanja, Dijelovi za automobilsku industriju i industriju mašina od čelika obojenih metalą CNC 3-osni obradni centri, Konvencionalno glodanje za pripremu i doradu, Kombinovano CNC struganje i glodanje, Zat varanje tolerancija - lanci mjera, PEĆI ZA TERMIČKU OBRADU ZAŠTITNE ATMOSFERE PEĆI ZA TERMIČKU OBRADU SA ZAŠTITBNOM ATMOSFEROM NITRIRANJE,CEMENTACIJA, POBOLJŠANJA, ŽARENJA, CARBONITRIRANJE NITROKARBURIRANJ ...
used
Barwell MR400 Top Load Ram Extruder
used
Key data: 100 , 140
Stock No.2452 1 used, partially overhauled and functionally tested pelletizing line Throughput up to 500 kg/h depending on the material, consisting of: Tamping unit Kreyenborg SW 100, drive 7.5 kW Extruder BKG single screw Ø 100 mm – 35 LD, Drive 132 kW – AC frequency controlled Screw speed up to 143 rpm.-1 screw depth 14 mm Heating capacity approx. 35 kW installed 1x athm. Degassing zone Screen-pack-changer Double piston Kreyenborg K-SWE 160 RS back-flush self-cleaning with screen surface 244 cm² BKG underwater pelletizer AH 300, complete with: Start-up valve incl. Hydraulic station Granulator with drive 4 kW Water pump 2.2 kW By-pass system, water tank with heating 9 kW installed and heat exchanger BKG granulate centrifuge TWE 300 with drive 3 kW pellet classifier table Control board and Siemens material feed conveying, big-bag filling station ...
used
Varex 3-layer blowfilm-extruder Head diameter: 630 mm Screw diameter: 70-90-70 mm( die gap: 2,4) Film width: 1390 – 2580 mm Film thickness: 10-200 my Output: max 480 kg /hour Winding diameter 1200 mm Core diameter 76/150/152 mm Energy: 295 kW/h Treatment: in+outside
used
1 x twin screw extruder, used Manufacturer: Battenfeld-Cincinnati Type: ATGOS 93P-28D Year of construction: 2007 Operating hours: approx. 62,000 hours Screw diameter: 2 x 93 mm (parallel) Screw length: 28 x D Screw speed: max. 26.0 1/min. Cylinder heating/cooling zones: 5/3 Adaper heating zone: 1 Tool heating zones: 5 Drive power: 50 kW (AC motor) Connected load: approx. 156 kVA System control: EXcPRO-XP with 10.4' TFT colour display Accessories: dosing unit (synchronized), material hopper, Degassing system with vacuum pump Output: max. 300 - 380 kg/h with U-PVC, depending on the material and product Note: new gearbox installed in 2014. Remark: The extruder is expected to be in production until the end of April 2023.
used
PE 300 plastic recycling and regranulation line was built in China in 2011 by Zhangjiagang Wuhe Machinery Co. LTD. The extruder for plastics used in the processing and manufacturing of various types of materials can produce up to 300 kg of parts in one hour of operation. The complete PE and PP plastic extrusion line includes a compactor, screw, cylinder, conveying system, heating system and temperature control panel. Material production begins by heating the plastic to a maximum temperature of 300°C in the 11 heating zones of the PE 300 granulating line, controlled by thermoregulators. The extruder then presses the material further through a 100 mm diameter screw located in a cylinder with abrasion and rust protection. At the end of the process, the machine head moulds the plastic to give it the right properties and shape. The PE 300 extruder is equipped with thermoregulators with ...
used
A fully equipped line for the production of nonwovens Spunbond Type YS 2400: Manufacturer: Faré (Italy) Useful width: 2400 mm Capacity: up to 514 kg/h Nonwovens weight: 10-100 g/m2
used
see PDF attached Condition very good
used
Corona Pull Roll Station 1 Primer Coater & Dryer 3 Extruders (with QSE Adapter, extrusion Do, Die, Gravimetrics 3+1) Auxiliary Unwind with splicing unit shafted desi! Laminator Edge Trim Razor Blade Beta Thickness Gauge PROTAGON Corona with Nip Station 3 Edge Trim Shear Cut Centre Slit&Spreader Ro Automatic Splicer Two direction Rewind Shafted Design Typlcal substrates: Paper:20 - 150 g/m2 Aluminium :6,35 - 25 μm PE:40 -120 μm BOPA: 15-50 μm BOPET: 9 -50 μm (smooth and metallised) BOPP: 15- 50 μm (smooth and metallised) Nonwoven PP: optional The extruder or extruders of the extrusion sta· motorized carriage. This carriage with a 3-\i UP/DOWN,LEFT/RIGHT and IN/OUT travel. The extruder carriage consists of: guide frame 4 wheels. Height adjustment traveldrive Side adjustment Control cabinets EXTRUDER A Screw diameter: 114.3mm (4.5 inches) Screw ...
used
Number Of Screws: 155 mm // Screw Diameters: 155-120 600 kg/h
used
Complet chrome steel 3-roller extruder Speed control Coarse feed rollers Maximum width:: 600 мм Stencil interchangeable Width/depth: 650 мм х 1'000 мм, height: 1'550 мм very good condition
used
Used twin-screw, parallel, counter-rotating extruder by Amut model BA92 NOMAX. New 2011. Output: 270 - 370 kg/h Hours of operation: 53638 h Other details: - Diameter of augers 92 mm - L/D ratio 28:1 - Drive power 60 kW (400V, 50 Hz, 3 ph) AC - Two sets of screws -for ABS processing -for PVC processing - Number of cylinder heating zones 7 - Number of cylinder cooling zones (air) 4 - Number of heating zones for head and adaptor 5 + 1 - Built-in pressure and temperature measurement system for plastic mass - Thermal oil unit for thermostating the worms for PVC - Drive power of vacuum degassing pump 11 kW - Drive power of screw feeder 1.5 kW - Without control (subassemblies available according to the list)
used
The line in good condition. The dowstream equipment made by company UNIPLAST. The line was produced PVC profiles for roller-shutter system.
used
we offer for sale an unused granulation unit for compounding lines.
used
Manufacturer Amut Model BA 92 Machine is like new, year 2020 Screw diameter : 92 mm
used
Mikrosan 90/23 PVC parallel extruder machine Capacity : 300 Kg / hour Machine is in good working condition. It can be seen in production. Screw and barrel has been recently replaced with new one.
used
Mikrosan MCV 68/25D Extruder like new condition Working hours : 1100 LD rate : 25 Maximum PVC-U capacity : 200 KG/hour Calibration Table Pulling device Tilting Table
used
Used dough weigher RHEON, type: KN-125 with belt scale and rotary table -Refurbished- - for single or double-filled products, such as coloured cookies, sweets or other pasta - all possible forms (see photo) - 100 recipes can be stored - in stainless steel and food sterile - with belt scale from OSC - optional double filling unit - Condition: very good, as new, completely overhauled - 6 months warranty Specifications: - Weight range: 10 - 90 g - Product length: no limit - Output: 1,200 - 6,000 pcs./h (depending on product) - Weight performance: max. 180 kg/h - Machine dimensions: 1,516 x 874 x 1,360 mm Visits and test runs are possible by arrangement.
used
It is 2003 model and working hours have been revised for 4 years. New screw barrel
used
Twin screw extruder SJZ92 / 188. 2009 onwards In perfect condition. Possibility of inspection in production.
used
Conical twin screw extruder Drive: DC 9kW motor heating zones: cylinder - 3, head - 3 cylinder cooling - oil
used
Krauss Maffei KMD 130-23 extruder Capacity : 1 Ton per hour Suitable for granule
used
Mikrosan Twin Screw Extruder Screw diameter : 67 mm Parallel screw
used
Mikrosan 90 mm extruder machine Capacity : 350 kg per hour 90 mm