126,698 used machines on RESALE, but how to find them? Machine Search
automatic baler Manufacturer: WELGER Type: SB 2000L Machine No.: 1307 51 321 specifications: Pressing force: 7 t Drive power: 11 kW Bale format 500 x 400 x length in mm Machine weight: approx. 1.9 t
Bale size (W x H) approx. 1,100 x 700 mm Bale weight approx550kg
pressure:2 t dayligth:80 mm Center of spindle to wall or column:100 mm weight of the machine ca.:0,5 t dimensions of the machine ca.:0,8 x 0,6 x 2,0 m Hand operated fly press, with center turning device appr. 100 x 400 mm length - Handwheel diameter 600 mm
press capacity:950 kN control:Siemens S7 Required air-pressure:6 bar loading area:1200 x 600 mm Pressure power:1000 kN total power requirement:18 kW weight of the machine ca.:6200 kg dimensions of the machine ca.:2600 x 1300 x 3100 mm
pressure:10 t distance between columns:450 mm :1500 mm table-size:450 x 400 mm weight of the machine ca.:470 kg dimensions of the machine ca.:1400 x 750 x 1600 mm
HOT PRESS model SIMI 4LP second hand machine plates useful size mm. 2500 x 1300 n.04 pistons diam.mm. 80 max. thrust Ton. 60 specific pressure max. kg.2 / cm2 opening mm. 320 hot water plates heating via wood boiler (optional) weight kgs. 3000
Key data: 15 t, 66 mm
Burger Press D07 Length 1.20 m Width 0.60 m Height 1.70 m 2 Hand control Switch to foot control 1 press die
pressure:10 t stroke:400 mm total power requirement:1,6 kW weight of the machine ca.:1,1 t dimensions of the machine ca.:1100 x650 x 2050 mm dayligth:500 mm table-size:400 x 450 mm Documents:vorhanden
pressure:160 t throat:360 mm stroke:500 mm total power requirement:17 kW weight of the machine ca.:7,2 t dimensions of the machine ca.:2,0 x 0,95 x 3,70 m table-size:900 x 630 mm Documents:vorhanden
Specifications: Capacity 300 to Stroke rate 35 strokes Plunger width 1000 mm Projection 450 mm Plunger stroke 20 - 140 mm Plunger adjustment 80 mm Engine power 30 hp Weight roughly estimated 18 tons
Specifications: Capacity 40 tons 2 strokes 57 + 86 H/min Projection 250 mm Plunger stroke 8 - 88 mm Plunger adjustment approx. 63 mm Table , WxD approx. 570 x 450 mm Max. installation height approx. 330 mm
pressure:160 t throat:360 mm stroke:500 mm Documents:vorhanden
pressure:20 t Stroke:230 mm table surface area:Ø600 mm distance table - lower edge of ram:770 mm weight:595 kg
Used multi-layer paver Zenit 844 Built in 1993 inclusive: 1 piece concrete mixer 750 l Teka 1 piece concrete mixer 500 l approx. 12 pieces of used moulds approx. 100 production pallets Used concrete multilayer machine Manufacturer: Zenith Type: 844 Year: 1993 including: - 1 pcs 750 liter mixer Teka - 1 pcs 500 liter blender - about 12 moulds - about 100 pcs production boards
weight of the machine ca.:620 kg dimensions of the machine ca.:1000 x 920 x 1550 mm
Pressure:175 t chamfer lenght:4100 mm distance between columns:3600 mm column arm:410 mm ram stroke speed:180 mm/sec return speed:135 mm/sec working speed:10 mm/sec work stroke:275 mm oil volume:200 l dayligth:550 mm table height:900 mm table width:90 mm total power requirement:15 kW weight of the machine ca.:12000 kg dimensions of the machine ca.:5100 x 2150 x 2850 mm
nominal force:100 t stroke:320 mm no. of strokes:35 /min distance between columns:360 / 250 mm Distance table/ram, max. stroke up, adjustment up:500 mm table surface area:320 x 450 mm table height over floor:660 mm ram surface:250 x 280 mm spindle diameter:125 mm power capacity:3,0 kW weight:4,5 t Dimensions (WxDxH):2,0 x 1,6 x 3,1 m
VORONEZH K8544 Hot Forging press YEAR : 1980 / 2008 OVERHAUL AND INSTALLED FORCE : 2500ton RAM STROKE : 350 mm RAM SIZE : 1120X1070 mm TABLE OVERALL SIZE : 1400X1200 mm NUMBER OF STROKES IN CONTINUOUS MODE : 60 NUMBER OF STROKES IN MANUAL MODE : 26 SHUT HEIGHT : 890 mm STROKE OF UPPER KNOCK OUT : 60 mm STOROKE OF LOWER KNOCK OUT : 70 mm MAIN MOTOR : 132KW (CHANGED TO HYUDAI HEAVY Y2012) PRESS OVERALL DIMENSION : 5380X4680X6400 mm HYDRAULIC BOLSTER NEW IN 2007 CONDITION : VERY GOOD WORKING CONDITIONS Trimming press available
pressure:60 t distance between columns:650 mm stroke:220 mm distance table/ram, max. stroke up, adjustment up:410 mm table surface area:600 x 525 mm hole in the table:110 mm table height over floor:900 mm side window:200 mm ram surface:560 x 490 mm power requirement:15,0 kW dimensions (WxDxH):1,9 x 1,3 x 2,7 m foundation pit:not necessary
Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw
Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw
SECOND HAND BENDING PRESS - plates dimensions mm. 3100X800 - opening mm. 800 - 8 cyl. diam. 80 mm.
pressure:250 t distance between columns:1110 mm stroke:250 mm Distance table/ram, max. stroke up, adjustment up:500 mm Table surface area:1100 x 900 mm Table height above floor:950 mm Side window:690 mm Ram surface:1100 x 900 mm Oil volume:730 l Power capacity:56,0 kW Dimensions (WxDxH):2,3 x 1,55 x 3,96 m
nominal force:160 t stroke:140 mm no. of strokes:85 /min distance between columns:400 mm distance table/ram, max. stroke up, adjustment up:500 mm table surface area:400 x 450 mm table height over floor:800 mm Allowed max. force:230 t ram surface:400 x 320 mm spindle diameter:125 mm power requirement:7,35 kW weight:5,0 t dimensions (WxDxH):1,7 x 1,2 x 2,9 m
pressure:300 t distance between columns:1800 mm stroke:1000 mm Distance table/ram, max. stroke up, adjustment up:1300 mm Table surface area:1600 x 1200 mm Table height above floor:1080 mm Ram surface:1600 x 1200 mm Weight:24,0 t Dimensions (WxDxH):2,8 x 2,1 x 6,0 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2
Specifications Maximum pressure: 60 tons Press force: 156 t/m² Bale size: 1100 x 1100 x 700 mm Bale weight: 400 kg Power supply: 400V/ 13kW Year of construction: 2014 Dimensions of the tailgate: 2815 x 1085 x 2250 mm Machine weight: 7.5 t The machine is functional
Specifications Maximum pressure: 50 tons Press force: 7.14 kg/cm² Duct cross-section: 1000 x 700 mm Bale weight: do 500 kg Power supply: 400 V/ 30 kW Number of ties: 3 horizontal Dimensions of the tailgate: 1250 x 950 mm Weight: about 10 tons Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the duct. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the press chamber for easy maintenance
Gluing Press / Press Rotor / Gluing Stars For the production of solid wood panels or similar Manufacturer: ACMA Levels: 4 Hydraulic Cylinders: 6 per level Hold-down: 2 frames per level Working area per level approx. 2900 x 1150 mm
Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw
no. of strokes:150 /min impact energy:420 kJ distance lower die block / ram gudeway:435 mm Throat:425 mm steel forging - rectangular up to:110 mm steel forging - diameter up to:125 mm power requirement:22,0 kW weight of hammer:3,9 t weight of anvil:3,0 t ram hammer weight:200 kg weight:6,9 t dimensions (WxDxH):1,1 x 2,3 x 2,4 m
Length 3615 mm; V45 die
Specifications Maximum pressure: 65 tons Pressing force: 84 tons/m² Duct cross-section: 1000 x 750 mm Bale weight: do 550 kg Power supply: 400 V/ 45 kW Year of construction: 2011 Number of ties: 4 vertical Dimensions of the tailgate: 1400 x 920 mm Weight: approx. 13 tones Bale tying: automatic
We offer directly on behalf of the owner : Bending press, second-hand Make : Graebener Maschinentechnik (Gräbener) Type : GRNM Year of construction : 2005 Flexural force max.: 16.000 kN ( 1.600 t ) Tool length : 1,600 mm Data at 520 N/mm2 Pipe diameter max.: 1,524 mm Tube diameter min.: 457 mm Sheet thickness max.: 40 mm Max. pipe length: 13.2 m Pipe length min.: 6m Pipe weight max.: 25 t Total power requirement approx.: 245 kW / 400 V / 50 Hz Approx. space: 27 x 3 m Total weight approx.: 90t / basic machine approx. 65t Further technical data and details on request or see data sheets in photos / PDF The machine was built in 2005, worked until 2021 and was professionally dismantled and packed for transport.
Key data: 200 mm
used press brake Trumpf TruBend V200 + BendMaster 60 Year of construction 2004 Pressing force max: 2000kN Stroke max: 365 mm Operating pressure max:340 bar 1 piece B0401A0009 = BendMaster 60 1 piece B0106A0073 = TRB V200-6A 1 piece of protective housing incl. lighting 1 piece of BendMaster roadway 14 meters in 2 meter segments 1 piece of system control system trump
max. load: 25 kN Projection: 90 mm Plunger strokes: 220 1/min Plunger adjustable: 30 mm Stroke adjustable: 2 - 40 mm Table dimensions: approx. 220 x 150 mm incl. The installed punching tool
Unused, crimping range 15-63mm, maximum aperture 75mm, 53.5 mpa, force 500 T, 3000W
25,000 LITRE KÖNIG & GÜNTHER STORAGE TANK / SPARKLING WINE PRESSURE TANK / PRESSURE TANK / 8 BAR, WITH AGITATOR PROPELLER, HORIZONTAL, ROUND, MADE OF STEEL https://eurolux.de/product/24-0563euba-25000-liter-konig-gunther-lager tank-sektdrucktank-drucktank-8-bar-mit-ruhrwerkspropeller-liegend-rund -aus-stahl KK UNI-RILL Specifications Cylinder wall thickness 12.3 mm Manufacturer: König & Günther Wall thickness floor 12.6 mm Surface coated on the inside, food-safe Surface painted on the outside Length 7100 mm Volume 25000 L Steel as a material Diameter 2250 mm Cylinder length 6000 mm Operating pressure 8 bar Agitator Propeller Stirrer Horizontal design Last Use Food Technical Documentation Yes Tank crown: 2 crane eyelets Flange connection 50 mm Front (horizontal tanks): Manhole oval Agitator propeller complete champagne pressure fitting wi ...
Pressure plate stacker Grafoteam PST 26 C; arm length 650mm; suitable for Heidelberg Suprasetter A52-74; optionally with stop interface for Heidelberg Suprasetter A52-74. Plate stacker Grafoteam PST 26 C; arm lenght 650mm; used for Heidelberg Suprasetter A52-74; for option with stop-interface for Heidelberg Suprasetter A52-74.
52,100 LITRE RIEGER SPARKLING WINE PRESSURE TANK / STORAGE TANK 8 BAR WITH SIDE MIXER, ROUND STANDING MADE OF V2A / SADDLE TANK https://eurolux.de/product/24-0515euba-52100-liter-rieger-sektdrucktan k-lagertank-8-bar-mit-seitlichem-ruhrwerksmixer-rund-stehend-aus-v2a-s atteltank Manufacturer: RIEGER Wall thickness cylinder 11 mm Surface inside 2B=IIIC sanded Surface marbled on the outside Volume 52100 L Material V2A (AISI 304) 1.4301 Total height 8000 mm Cylinder height 5500 mm Diameter 3250 mm Operating pressure 8 bar Working temperature 20 C Agitator Propeller Stirrer Vertical design Number of feet 5 Parts in contact with the product: Yes Last Use Food Technical Documentation Yes AS UNI-RILL 047-500 Topsoil: Klöpperboden 4 crane eyelets downward CIP line DN 50 with flange connection with pressure line DN 25 Tank cylinder: Manhole ovall 35 ...
maximum number of results exceeded
please refine your search
