buc used for sale

Technical data: Clamping opening max.: 850 mm (950 mm) Clamping claw opening max.: 620 mm Output of the main voltage: hydraulic Cutting length: 6000 mm Number of clamping planks: 4 stubble - Incl. new running rails - stiffened in profl steel construction with cross-beams - Single buck adjustment - Cutting staer adjustment, multi-chain drive and ball-bearing connection shaft by electr. Positioning drive. - Automatic lubrication for saemt rails and Guides. - Low wear and high adjustment speed due to central hydraulic clamping claw adjustment with automatic Clamping pressure reduction in case of retracted clamping claws - Trunk can be in the tense state in the Laengaxis to be aligned - Cutting of conical timber or cutting parallel to the Tree edge possible - 3 pairs of regular turners "Quick Turner" - Wheel mount directly connected to clamping buck bottom, thus  ...

Manufacturer PWH Flow capacity 400 m3 hour of bulk material Grit 0 to 30 mm Bulk weight 0.84 to 0.90 to / m3 Water content 18% Heap height 12 meters Operating voltage 380 V Control voltage 220 V Bucket capacity: 100 litres • Number of shovels: 8 pieces • Bulk per minute: 60 • Theoretical power: 360 m3/h • Effective power: 280 m3/h • Bucket wheel diameter: 3.45 m • Circumferential force (wheel): 15,000 N • Cutting speed on the knife: 1.35 m/sec • Removal height (heap height): 12 m • Discharge of the lowered wheel: 11 m • Lifting height on the paddle wheel: 6 m • Lifting speed on the paddle wheel: approx. 3 m/min • Senovice speed on the paddle wheel: approx. 3m/min • Swivel speed: approx. 12 m/min • Angle of rotation of the trolley (suspension): 360 • Angle of rotation of the trolley

Material: Stainless steel Built: 1993 Content: 1770 ltr Pressure inside: 0.5bar Pressure outside: 10bar Weight: 5000 kg L x W x H: 4700mm/900mm/1200mm An indirect heat exchanger with mechanical material transport. Very good condition. YOU ARE A NEW, OUTDATED AND USED

feeder: • pallet feeder • machine number (feeder) 34103/88 • counter EVZ 30 1st folding unit: • pre-slitter shafts • 4 buckle plates • rear-mounted slitter shafts • noise prevention 2nd folding unit: • working width max. 94cm • 4 buckle plates • rear-mounted slitter shafts • noise prevention 3rd folding unit • working width max. 66cm • 2 buckle plates • rear-mounted slitter shafts • noise prevention Still in operation: No Available: sofort

MATEC Stappler tipping bucket type 2 The tipping bucket can be locked with a bolt with cotter pin so no tipping is possible. The tipping buckets can be supplied also with a hydraulic tilting device. The blades are 1950 mm wide and type 2 1300 mm deep. The standard blade height is 450 mm. Solid wall or lattice towers can be ordered as accessories. The nominal weight of the shovel is 2000 kg. Each blade has 4 lifting eyes for crane handling. 4 mm thickness, corners and a replaceable wear bar reinforced permit prospecting. Other blade dimensions are possible upon request. Year 2017 New machine Spare parts/service MATEC CH-4952 Eriswil/DE-79618 Rheinfelden Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041  ...

Inclined lift with motorized winch (7.5 kW / 36 UPM), lifting bucket (1,000 l. usable volume), weighing frame / foot station (2,000 kg max.), 25 m rope and head station for material transfer. Rope and SEW winch drive are new; Elevator was used to feed an Eirich intensive mixer type R(V) 18. Technical documentation is available.

; operational

; operational

Chain elevator in modular design, horizontal and vertical conveying distance are variable (last used setup: 6,0 m horizontally at bottom > 3,0 m vertically > 18,0 m horizontally at the top), Incl. plastic pendulum buckets, steel ducts 410 mm x 410 mm in different langths, drive station with gear drive 1,1 kW / 56 RPM, conveyor chains, 2 pcs. drive- directing-stations, tensioning-station, return stop mechanism and 3 pcs. discharging stations. Conveying speed: 0,25 m/s.

NEUMASCHINE - Double-sided belt grinding or polishing machine, different Configurations possible - grinding / grinding grinding polishing polishing motor 4 kW, polishing disc max. 120 x 500 mm, max. diameter contact disc 400 mm, grinding belt 50 x 3500 mm; NEW MACHINE

Size max 360 x 650 mm min 80 x 100 mm Speed max 150 m/min Equipment o flat pile feeder 1st folding unit: o 4 buckle plates o Festa foldingrolleradjustment o noise prevention ; working condition

Diameter: 2.0 m, width: 500 mm, trough: approx. 2,000 x 1,000 mm, capacity: 10 tons / h (0-4mm), E - motor with 3.6 kW

Size max 1.120 x 1.450 mm min 250 x 250 mm Speed max 10-16 m/min Equipment: feeder o pallet feeder (MBO) o MC control 1st folding unit: o 4 buckle plates o rear-mounted slitter shafts o noise prevention 2nd folding unit: o 4 buckle plates o rear-mounted slitter shafts o noise prevention 3rd folding unit: o 2 buckle plates o rear-mounted slitter shafts o noise prevention delivery: o belt delivery ; working condition

Double grinding bracket, knife grinding machine Turning one side quickly, the other side running slowly in the water, e.g. for grinding knives Grinding wheel diameter approx. 300mm Weight approx. 250kg Ready to demonstrate under electricity. Special price

Buckles Heidelberg Model Ti52 Specifications 1 set of buckles for Heidelberg Stahlfolder Ti52/4, might be suitable for older versions Available direct

tilting recess, chip recess, Chip wagons, Forklift trly, Scrap bucket Dimensions: Width x Length x Height (approx. 74 x 73 x 135 cm) Total height: approx. 94 cm 4 wheels handle rocker arm Outlet tap Portable with forklift As shown, it is sold with various sheet steel boxes. All information without guarantee

roll diameter: 51 mm Wheel width: 125 mm weight: 20 kg height adjustment: 560-975 mm Furnishing: - Heavy three-sprue design for maximum loads - Roller support steplessly height adjustable and clampable - Safe workpiece support - Solid and heavy-duty galvanized steel rollers - With two rollers, each 125 mm long, ideal for pipes, ... techn. Data : Roll width 2 x 125 mm Roll diameter 51 mm Height adjustment 560 - 975 mm Load capacity, max. 700 kg Standpipe diameter 74/52 mm Weight approx. 20 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tilting recess, chip recess, Chip wagons, Forklift trly, Scrap bucket Dimensions: Width x Length x Height (approx. 74 x 73 x 135 cm) Total height: approx. 94 cm 4 wheels handle rocker arm Outlet tap Portable with forklift As shown, it is sold with various sheet steel boxes. All information without guarantee

roll diameter: 51 mm Wheel width: 350 mm weight: 20 kg height adjustment: 575 - 975 mm Load capacity per arm: max. 700 kg Furnishing: - Safe workpiece support - by massive and heavy-duty galvanized steel rollers - Roller support steplessly height adjustable and clampable - Problem-free and efficient material transport for the supply and removal of workpieces techn. Details: - Load capacity, max. 700 kg - Standpipe diameter 74/52 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tilting recess, chip recess, Chip wagons, Forklift trly, Scrap bucket Dimensions: Width x Length x Height (approx. 74 x 73 x 135 cm) Total height: approx. 94 cm 4 wheels handle rocker arm Outlet tap Portable with forklift As shown, it is sold with various sheet steel boxes. All information without guarantee

small tipping container, width 63.5, height 98.5, length 125.0 cm for forklifts with fork width 11.5 cm

tilting recess, chip recess, Chip wagons, Forklift trly, Scrap bucket Dimensions: Width x length x height (approx. 74 x 73 x 135 cm) with sheet metal wall attachment approx. 30 cm, three sides Total height: approx. 94 cm 4 wheels handle rocker arm Outlet tap Portable with forklift Sold as shown with sheet steel cabinet. All information without guarantee

tilting recess, chip recess, Chip wagons, Forklift trly, Scrap bucket Dimensions: width x length x height (approx. 94 x 76 x140 cm) Total height: approx. 118 cm 4 wheels handle rocker arm Outlet tap Portable with forklift Sold as shown with various sheet steel boxes. All information without guarantee

ID3182 2 piece Strödter Vigomat VP 250-2,5 year/Year of construction 2013 articulated manipulators, pneumatic power supply Load capacity 240 kg Max. Max. load torque on load handling attachment 1200 Nm Max. Horizontal working range: Radius R 3.7 m Max. Stroke: 1.45 m Max. Max. lifting speed: 0.8 m/s Type of attachment Pedestal Weight of device 755 kg Noise emission < 70dB Pneumatic working pressure 6 bar Max. Air consumption: max 40 NI /double stroke Diameter of main cylinder 200 mm Buckling manipulators, power supply pneumatic Load capacity 240 kg Max. load torque at the noise pick-up device 1200Nm Max. horizontal working range: Radius R 3.7 m Max. stroke: 1.45 m Max. lifting speed: 0.8 m/s Fastening type of pedestal Weight of the device 755 kg Noise level < 70dB Pneumatic working pressure 6 bar Max. air consumption: max 40 NI /double stroke Diameter master ...

height: 410 - 610 mm width: 230 x 230 mm weight max. in kg: 15000 kg height adjustment: 200 mm loading area: 100 x 100 mm thread: TR 56 weight: 25 kg Bolt block / outrigger under load Height adjustable with trapezoidal threaded spindle TR56 2 pieces in stock! The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Langguth V 81 Bucket Destapler,Destapler for unpalpping buckets Bucket size from 2.5 - 20 l automatic handle alignment Very good condition, directly from production!

Filling is established with a 2¨flow meter - FLOW 33 accuracy 0,5% 1.2 The machine is built with ΙΝΟΧ ASI304 1.3 The machine will come with a full closed cabin for hygiene 1.4 Closure of bucket with film per kg & UV lamp 1.5 Automatic conveying per kg 1.6 Automatic over cap Applicator for 2,5 & 5 kg 1.7 System for CIP connection 1.8 Control panel with touchscreen Siemens IP65 and PLC Siemens, immediate choose of kg .The change over is immediate and needs no handling 1.9 Capacity 4,5t/hour on 5kg 1.10 ΗΕΡΑ filter in cabin 1.11 Stainless steel lobe pump OMAC Type : ΒΕ 220 Machine dimensions: Length : 5 meters Width : 1 meter Height : 230 meters

MBO K55-4KTL + window buckle plate In great working condition. - 2 Knives - 4 buckle plates + window buckle plate - gluing system (not complete) - Vaculift, Vacubelt, Vacutable

Kemper bucket elevator for bread plant Type: BE 11 Possible applications in all dough processing lines transport also of soft doughs Space-saving design optionally 1 or 2 pieces of dough Run-off belt Dimensions: Height: 216cm Width: 71cm Depth: 120cm

Kemper bucket elevator for bread plant Type: BE 11 Possible applications in all dough processing lines transport also of soft doughs Space-saving design optionally 1 or 2 pieces of dough Transverse belt left-hand / Cross-band right-hand with scales

sell well serviced screen bucket Terra ST

Screen bucket 355mm unused Manufacturer Haener Model HSL280 MS03 ECO S355 Type screen bucket with quick-release frame MS03 Type Skeleton Excavator Bucket (Unused) Capacity 140 litres Weight 86kg

Starting height: 10 m Chalice size: 160 x 180 x 150 mm 66 pcs Electrical data: 2.2 kW; 380 V

Starting height: 25 m Duct size: 310 x 220 mm Overall size: 1050 x 350 mm X total height: 26 m Voltage: 380 V

Backhoe bucket, excavator bucket, demolition bucket, trenching bucket -execution: stable -Width: 500 mm -Height: 900 mm -Depth: 1100 mm -Admission intermediate dimension: 185 mm -Bore mounting: Ø 50 mm -ripping teeth -The mounting on the spoon can be changed by us at an additional cost -Own weight: 190 kg

Buchholz relays, transforamor protection relays EGEM BF 50/10 2 TGL 15290 for 2000 - 10000 kVA transformers New ! Dimensions: 290 x 170 x 270 mm

Buchholz relays, transforamor protection relays EGEM AG 25 TGL 15290 for 1600 kVA transformers New ! Dimensions: 190 x 180 x 170 mm

Centrifugal bucket set for steel gravel blasting machine GISAG PDS 2500 Dimensions(one bucket): 160 x 50 x 17 mm Thickness without side edge: approx. 12 mm bore: Ø 11 mm spare part e.g. for GISAG PDS 2500/3 ! centrifugal shovel set consists of 8 pieces New ! Dimensions: 160 x 160 x 50 mm

TECHNICAL SPECIFICATIONS Manufacturer: SMT STICHWEH Description: Drainage bucket wheel Design: Cup wheel in the middle Type: ES 40 BB Year of construction: 1983 Tub length: 3,375 mm + plus spout 490 mm Tub height: 1,150 mm Tub width: 4,080 mm Transmission: Stiebel Parallel shaft gearbox 5042 Dimensions screen mat: 700 x 740 x 8 mm Weight: approx. 5,500 kg SPECIFIC COMMENT - 1 discharge conveyor available (AA= 10 m /BB= 650 mm) - No cracks, no deformations

1 unit 2 buckles + 1 unit 2 buckles

AUTOMATION FOR THE PLASTIC BUCKET INDUSTRY Year of manufacture 2016 Up to 1800 buckets per hour Performance data Shapes: round, oval, square Stacking height: 1200 mm Article sizes: 1 l - 12 l or 10 l - 30 l Quick-change device Servo control with 4 axes SPS with recipe management Optical registering conveyor belt

Centrifugal bucket set for steel gravel blasting machine, reinforced version GISAG PDS 2500 Dimensions (one bucket): 160 x 50 x 28 mm thickness without side edge: approx. 10 mm bore: Ø 11 mm spare part e.g. for GISAG PDS 2500/3 !bore: Ø 11 mmbr /br Centrifugal bucket set consists of 8 pieces New ! Dimensions: 240 x 160 x 50 mm

content: . cbm power requirement: . kW bolt-diameter: 66 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Mini excavator bucket, backhoe bucket, backhoe bucket, demolition bucket -Width: 470 mm -Height: 470 mm -Depth: 600 mm -Admission intermediate dimension: 135 mm -Bore distance: 110 mm -Bore: Ø 35 mm -Ripper teeth -extended cutting edge -The mounting on the spoon can be changed by us at an additional cost -Own weight: 80 kg

Backhoe bucket, backhoe bucket, demolition bucket -Execution: stable -Content: 175 l -Width: 680 mm -Height: 650 mm -Depth: 700 mm -Quick change holder -Admission intermediate dimension: 260 mm -Ripper teeth -The mounting on the spoon can be changed by us at an additional cost -Net weight: 230 kg

Transport trestle, steel trestle, heavy-duty rack -Execution: stable -Total height: 2720 mm -Support height: 2350 mm -Width: 3300 mm -Depth: 750 mm -Weight: approx. 200 kg

Side dump bucket, wheel loader bucket -Wheel loader shovel -Shovel inside: 1850 x 670 x 800 mm -Own weight: 480 kg -Execution: stable -Admission inside: 860 mm -suitable for: Atlas

Lid folding machine, folding machine, folding machine, lid folding machine, can folding machine, can folding machine -Lid folding machine for metal buckets -The machine makes the fold for the lid -Dimensions: 1000/1200/H1150 mm -Weight: approx. 800 kg

Backhoe buckets, excavator buckets, demolition buckets, ditch buckets, excavator buckets, ditch cleaning buckets -Manufacturer: KSW, backhoe type TL LK5-600 -Intake: KSW03L -Width: 600mm -Content: 158 liters -Recording on the spoon: can be changed by us for an additional charge -Dimension: 935/600/H690 mm -Own weight: 152 kg