briquette press used for sale

Equipped with new control and laser protection from PILZ; including 1 set of tools with 2 V die sizes

V6 30 degree T mold set; length approx. 3.1 meters

Unused, crimping range 15-63mm, maximum aperture 75mm, 53.5 mpa, force 500 T, 3000W

Specifications: Capacity 50 tons Stroke rates 115 rpm Projection 250 mm Plunger stroke 8 - 120 mm Plunger adjustment approx. 70 mm Table , WxD approx. 650 x 500 mm Diarrhoea och approx. 250 x 180 mm

Maximum force: 1600 tons Slider stroke length: 400 mm Unattainable-course: 12 mm Number of courses of a slider per minute: 16 Number of single turn-on: 12 The closed height: 870 mm Adjustment: 220 mm Under-forginig plate: -From left to right: 1600 mm -From front to rear: 1600 mm -Thickness: 650 mm Slider overall dimensions: 1600x1600 mm Aperture in a table: 1000x1000 mm window dimensions in cheeks: 1650x1650 mm Course of a rigid pusher in a slider: 100 mm Force of a rigid pusher in a slider ton-force: 80 Main electric motor power: 110 kW Course of pneumatic pillow: 160 mm Force of pushing out of a pneumatic pillow ton-force: 71 Hydropneumatic pillow: -Working course: 250 mm -Force of pushing out ton-force: 25 -Force of a clip ton-force: 250 Press overall dimensions: 4670x4670x8110 mm Press weight: 147 tons

automatic baler Manufacturer: WELGER Type: SB 2000L Machine No.: 1307 51 321 specifications: Pressing force: 7 t Drive power: 11 kW Bale format 500 x 400 x length in mm Machine weight: approx. 1.9 t

Length approx. 1800 mm; WILA NS Recording

"Max. test pressure: 7 tons Max. distance from lower bearing: 2000 mm Max. distance from upper bearing: 600 mm Max. sample width: 250 mm Max. sample height: 200 mm" on pallet

Unused machine, incomplete

HOT PRESS model SIMI 4LP second hand machine plates useful size mm. 2500 x 1300 n.04 pistons diam.mm. 80 max. thrust Ton. 60 specific pressure max. kg.2 / cm2 opening mm. 320 hot water plates heating via wood boiler (optional) weight kgs. 3000

Tot.kW 43 Volt 400V /50Hz

Bale size (W x H) approx. 1,100 x 700 mm Bale weight approx550kg

Volume 350 L

Equipped with 10 crimp sets; unused

Hydraulic Hose Press; Crimping range: 15-63mm, Max aperture: 75mm, Voltage: 380V, Wattage: 3000W, Pressure: 53.5 Mpa Packing size: 780x540x1350 Weight incl. packaging: 280 kg Unused.

Key data: 15 t, 66 mm

Burger Press D07 Length 1.20 m Width 0.60 m Height 1.70 m 2 Hand control Switch to foot control 1 press die

Specifications: Capacity 300 to Stroke rate 35 strokes Plunger width 1000 mm Projection 450 mm Plunger stroke 20 - 140 mm Plunger adjustment 80 mm Engine power 30 hp Weight roughly estimated 18 tons

On base and with vice

Incl various press tools and 3x foot control pneumatic connections aluminum profile molds tool metal tray. For aluminium window and door profiles corner connections

Includes 1 set of tools; equipped with steered X axis

equipped with Delem CNC control and Wila hydraulic top clamping; Exclusive tools

Used multi-layer paver Zenit 844 Built in 1993 inclusive: 1 piece concrete mixer 750 l Teka 1 piece concrete mixer 500 l approx. 12 pieces of used moulds approx. 100 production pallets Used concrete multilayer machine Manufacturer: Zenith Type: 844 Year: 1993 including: - 1 pcs 750 liter mixer Teka - 1 pcs 500 liter blender - about 12 moulds - about 100 pcs production boards

HYDRAULIC PUNCHING PRESS Inv. No. 13.085P1 Make SAHINLER Model HKM40 Capacity 40 Ton Punching Ø 20 in 15mm Stroke 50 mm Radius 175 mm Round cutting 30 mm Square cutting 25 mm Angle bar 80 x 80 x 8 mm Flat bar 200 x 13 mm 300 x 6 mm Blade length 356 mm Motor power 3 KW Weight 580 Kg

With foot switch, on metal base, self-made.

This WEMHÖNER Variopress Basic 1000S was manufactured in 2018. Ideal for efficient laminating processes, this machine ensures consistent performance. Consider the opportunity to buy this WEMHÖNER Variopress Basic 1000S laminating press. Contact us for more information.

Capacity: 80 ton Throat depth: 280 mm Ram stroke: 8 - 140 mm Slide adjustment: 100 mm Shut height (stroke down, adjustment up): 520 mm Table surface area : 850 x 670 mm Slide area: 550 x 400 mm Hole in table: 250 x 180 mm Number of strokes: 20 - 100 s.p.m. Required power: 7,5 kW Dimensions L x W x H: 2210 x 1510 x 2750 mm Oil volume: 50 l Die weight at the ram max.: 300 kg Weight of machine approx.: 8,3 ton

Specifications: Capacity 40 tons 2 strokes 57 + 86 H/min Projection 250 mm Plunger stroke 8 - 88 mm Plunger adjustment approx. 63 mm Table , WxD approx. 570 x 450 mm Max. installation height approx. 330 mm

Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw

Press capacity: 50 ton Throat depth: 265 mm Stroke: 250 mm Daylight: 400 mm Table surface area : 700 x 450 mm Slide area: 550 x 300 mm Table height over floor: 850 mm Approach speed: 32 mm / sec Working speed: 6,3 mm / sec Return speed: 42 mm / sec Required power: 4 kW Dimensions L x W x H: 1290 x 1160 x 2085 mm Weight of machine approx.: 1,75 ton

Press capacity: 45 ton Ram stroke adjustable: 20 - 80 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 300 mm Free frontal opening L-R: 710 mm Table surface area : 700 x 450 mm Slide area: 700 x 360 mm Hole in table: 600 x 100 mm Number of strokes: 80 - 400 s.p.m. Required power: 10 kW Height over floor approx.: 2900 mm Weight of machine approx.: 7,2 ton Control: Siemens S7

VORONEZH K8544 Hot Forging press YEAR : 1980 / 2008 OVERHAUL AND INSTALLED FORCE : 2500ton RAM STROKE : 350 mm RAM SIZE : 1120X1070 mm TABLE OVERALL SIZE : 1400X1200 mm NUMBER OF STROKES IN CONTINUOUS MODE : 60 NUMBER OF STROKES IN MANUAL MODE : 26 SHUT HEIGHT : 890 mm STROKE OF UPPER KNOCK OUT : 60 mm STOROKE OF LOWER KNOCK OUT : 70 mm MAIN MOTOR : 132KW (CHANGED TO HYUDAI HEAVY Y2012) PRESS OVERALL DIMENSION : 5380X4680X6400 mm HYDRAULIC BOLSTER NEW IN 2007 CONDITION : VERY GOOD WORKING CONDITIONS Trimming press available

Press capacity: 80 ton Ram stroke adjustable: 4 -60 mm Slide adjustment: 0 - 80 mm Shut height (stroke down, adjustment up): 310 mm Free frontal opening L-R: 800 mm Table height over floor: 1150 mm Table surface area : 780 x 640 mm Slide area: 800 x 460 mm Hole in table: 690 x 170 mm Number of strokes: 30 - 300 s.p.m. Required power: 21 kW Height over floor approx.: 2900 mm Weight of machine approx.: 12 ton Control: Siemens S5

Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw

Specifications Maximum pressure: 60 tons Press force: 156 t/m² Bale size: 1100 x 1100 x 700 mm Bale weight: 400 kg Power supply: 400V/ 13kW Year of construction: 2014 Dimensions of the tailgate: 2815 x 1085 x 2250 mm Machine weight: 7.5 t The machine is functional

Press capacity: 35 ton Ram stroke adjustable: 6 - 50 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 250 mm Free frontal opening L-R: 430 mm Table surface area : 410 x 410 mm Slide area: 307 x 187 mm Hole in table: 170 x 110 mm Number of strokes: 60 - 300 s.p.m. Weight of machine approx.: 2,4 ton

Press capacity: 45 ton Ram stroke adjustable: 10 - 40 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 220 - 300 mm Free frontal opening L-R: 560 mm Table surface area : 550 x 450 mm Slide area: 550 x 360 mm Hole in table: 450 x 100 mm Number of strokes: 100 - 500 s.p.m. Required power: 7,5 kW Weight of machine approx.: 6,2 ton

Capacity: 250 ton V ? Ring nominal force: 30 - 125 ton Counter ram nominal force: 30 - 125 ton Ram stroke: 67 mm Table surface area : 560 x 600 mm Slide area: 560 x 560 Number of strokes: 80 s.p.m. Weight of machine approx.: 14.000 kg

Gluing Press / Press Rotor / Gluing Stars For the production of solid wood panels or similar Manufacturer: ACMA Levels: 4 Hydraulic Cylinders: 6 per level Hold-down: 2 frames per level Working area per level approx. 2900 x 1150 mm

SECOND HAND BENDING PRESS - plates dimensions mm. 3100X800 - opening mm. 800 - 8 cyl. diam. 80 mm.

A four-column stamping press Exner with electronics overhauled in 2011 is available. Press force: 340t, pressure cylinder: 1, pressure cylinder diameter: 380mm, ram stroke: 180mm, stroke adjustment: 100mm, installation height: 400mm, ram diameter: 260mm, table dimensions X/Y: 910mm/610mm, machine dimensions X/Y/Z: approx. 1300mm/1600mm/2950mm, weight: approx. 6500kg. An on-site inspection is possible.

Press force: 135t, bending length: 3000mm, nominal bending length: 2600mm, frame width: 2600mm, throat depth: 250mm, ram stroke: 120mm, working speed: 7mm/s, machine weight: approx. 6800kg. An on-site inspection is possible.

Key data: 180 t

DURENDUS 180 T Workshop Press – Single Column Press – 1,400 mm Clear Width, 400 mm Stroke The machine shown here has already been built and delivered on behalf of a customer. We can supply you with this machine from stock or manufacture it from scratch – gladly taking into account individual options. It is a hydraulic workshop press for press-fitting, straightening and assembly work in the workshop and industrial sector. Base price: 8.950 € net Options (on request): The options listed are based on completed customer projects and enable the machine to be specifically adapted to the respective application. The basic machine represents a functional basic design – in practice, in most cases it is expanded with additional equipment and configured accordingly for the specific project. Table top with X-shaped T-slot 700 × 1,000 × 100 mm Pressure adjustment Lateral dis ...

Key data: 200 t

DURENDUS 200 T Workshop Press – Single Column Press – 1,500 mm Clear Width, 400 mm Stroke The machine shown here has already been built and delivered on behalf of a customer. We can manufacture this machine for you at very short notice – gladly taking individual options into account. It is a hydraulic workshop press for press-fitting, straightening and assembly work in the workshop and industrial sector. Base price: 10.750 € net Options (on request): The options listed are based on completed customer projects and enable the machine to be specifically adapted to the respective application. The basic machine represents a functional basic design – in practice, in most cases it is expanded with additional equipment and configured accordingly for the specific project. Table top with X-shaped T-slot 800 × 1,200 × 120 mm Pressure adjustment Lateral displacement of the ...