bowl lift used for sale

Load: 300kg, weight: 104kg, including documentation.

Max. load: 227kg, operational hours counter: 979h, with documentation, the machine has not been used for 2.5 years, the slewing ring makes noise when extended, the brakes are difficult to control, brakes somewhat abruptly, the batteries were renewed a few years ago, an on-site inspection is possible.

There are 2 identical dalmec lifting aids available. Max. Load capacity: 140kg, operating pressure: 0.65Mpa.

Load: 1t, documentation available.

Max. total load: 5t, weight: 8.89t, without accessories, spare parts or documentation, was maintained regularly.

Including battery charger.

Max. load: 910kg, weight: 2.93t.

Nominal load: 1.3t, drive power: 0.6kW, length: 1585mm, width: 650mm, weight: 179kg.

Nominal load: 8t, weight: 12.3t, operational hours counter: 5166h, including three meter long forks, without documentation.

Load: 2.5t, lifting height: 3220mm, length: 2262mm, width: 1199mm, height: 2230mm, weight: 4.4t, an on-site inspection is possible.

Load: 7.7t, max. stroke: 3200mm, weight: 5.8t.

; Gross weight [kg]: 3320; Inspection Date: 2024-03-18; Maximum lift capacity [kg]: 230

; Gross weight [kg]: 7040; Inspection Date: 2024-01-02; Amount of previous owners: 1; Maximum lift capacity [kg]: 230

With boiler scraper; Lacquered finish; Already dismantled; Analog control;

Lifting Column for charging machines or for transferring various containers. Incl. ceiling fixing. Ceiling height: approx. 7300 mm. Lifting column consisting of: Lifting mast, lifting trolley, lifting, swivelling and load drive, control panel. Max. load 800 kg. Unit is new (unused).

conveyor size 3000mm L , With vibratory flour shaker and ingredients dispenser

Height: 3700 mm Length: 2650 mm Width: 930 mm Distance between the conveyor: adjustable

Translyft TCB 1000 Scissor lift Serial: 14034335 2014, Stainless scissor lift, capacity 1000Kgs, total raised height 800mm, table 1500mm x 1000mm, 3Ph

dough bowl lifter

Used lifting kneader DIOSNA, Type: D 200 / 2G -In bakery condition- - 2 speed levels - for 200kg dough or 125kg flour - Engine re-mounted - New V-belts - New timer - Stainless steel boiler - Plasticized kneading spiral nickel-plated and food-grade - Condition: Good, technically tested, cleaned, immediately ready for use Boiler volume: for 200 kg dough El. Connection: 380 V, 50 Hz, 7.1 A Inspection and test run are of course possible by arrangement.

Used lifting kneader DIOSNA, type: S 35 Plus -In bakery condition- - for 35 kg dough - Machine runs smoothly - technically tested and cleaned - very nice condition - Weight: approx. 250 kg Inspection and test run are of course possible by arrangement.

-Lifting tipper König -for König and Diosna Kessel -Weight 950 kg -Height: 235cm

Type: FXE-MP 160-90 S Payload: 300 kg from 15 mm Truss Type: FXE-T100-800 S Payload: 100 kg Year of construction: 2019 Condition: like new Height: 800 mm Width: 800 mm Depth: 165 mm Height of horizontal traverse: 400 mm

18 transport pallets for concrete walls or similar and 1 pallet lifter

Lifting tipper Kemper HK 200 LD for San Cassiano boiler - Kemper HK 200 LD lifting tipper - for San Cassiano boiler - with boiler cutter - Year of construction 2004

Vacuum lifting device for paper rolls NAGRON AEROLIFT Vacuum lifter for the paper industry Woudenberg Holland Type R96-20 Fabr. No. 9745 Year of construction 1999 Payload 2000 kg Centering mandrel 90 mm Suction surface Outer diameter 850 mm (plus seal)Suction surface inner diameter 250 mm (minus seal) Seal width 50 mm Suction surface 0.5 m2 Negative pressure min. -800 mbar Pumping speed approx. 100 m³/h per vacuum pump Motor power 2x 2.2 kW Mains connection 400 Volt, 50 Hz - 2 pieces Rietschle vacuum compressor, type VCE 100 Dimensions x H 1600 x 2250 mm Height with centering mandrel 2500 mm Total height in transport frame 2950 mm Net weight 2,5 ton.; used

Hydraulic scissor lift table GRUSE type HF 2 HS Fabr. Product no.: 75432 Year of construction 2008 Load capacity 250 kg Platform size 1190 x 740 mm Useful stroke max. 1270 mm Construction height - table bottom 285 mm Construction height - table top approx. 1555 mm Operating pressure max. 150 bar at 250 kg engine power 0.75 kW mains connection 230 volts, 50 Hz - Rotary switch for up and down on the hydraulic unit - Double shears with a lifting cylinder- Pipe rupture protection directly on the cylinder - circumferential safety contact strip with limit switches under the upper ramen - adjustable limit switch for the stroke restriction - hydraulic unit with tank separately standing own weight table unit approx. 180 kg net weight hydraulic unit approx. 30 kg good condition; used

Hydr. Scissor lift table TREPEL - L. A. VAN EIJLE & Co. Year of construction approx. 1980 Load capacity approx. 5 ton. Platform size 1700 x 1100 mm Stroke max. 515 mm Construction height Table bottom with rail castors 535 mm Height Table bottom without rail castors 480 mm Table height raised with rail rollers max. 1050 mm Table height raised without rail rollers max. 995 mm Travel speed Rail chassis approx. 8.5 meters/min. Motor power 4 kW Mains connection 400 Volt, 50 Hz - Manual switch for up and down on the cable - Safety limit switch - Hydraulics with tank mounted in the underframe- Lifting shears with two lifting cylinders - The table was movable on rails, 4 rollers on the base, 200 mm - Drive of the rail rollers via SEW Gear motor with chain Space requirement L x W x H 2070 x 1350 x 1050 mm net weight approx. 1.3 ton. good condition; used

Vacuum lifting device, vacuum lifter Custom-made as handling device for an industrial robot Year of construction 2008 Payload approx. 60 kg Suction foot spacing min. 120 x 150 mm Suction foot distance max. 700 x 600 mm- 4 pieces Suction feet 100 mm- 4 pieces Vacuum ejectors, vacuum generator PIAB with compressed air connection 8 mm - 2 pieces Cross member, adjustable in width via servo drive from 150-600 mm- Suction foot distance adjustable via 2 servo drives from 120-700 mm - Suction cup adjustment via 3 servomotors REXROTH MSK040C-0600-NN-M1-UP0-NNNN- Very complex and precise design with linear guides and trapetz threaded spindles- Flange plate for suspension or flanging on the robot Length: 105 cm, width: 66 cm, height: 54 cm Net weight approx. 120 kg good condition ; used

Stacker truck, walker, manual pedestrian stacker LOGITRANS type LF 1001 / 1600 Tool lifter series No: 051E04006100 Year of construction 2005 Load capacity: 1000 kg Lifting height: 1600 mm Fork length: 600 mm Platform size: 800 x 650 mm Total length: 1200 mm Total width: 800 mm Construction height: 1930 mm- Lifting by pumping movement with the traction dike- 2 lifting speeds approx. 36 strokes up to lifting height 1600 mm or approx. 10 strokes for 10 cm lifting height. - Driving by pushing hand fork stroke in single mast with free lift net weight 198 kg very good condition; used

Hydr. Scissor lift table WEIDMANN type E5/13-1 Fabr. No. 30403339 Year of construction 1982 / 2007 Load capacity 500 kg Platform size 2000 x 1200 mm Stroke max. 1280 mm Construction height - table bottom 290 mm Construction height - table top max. 1570 mm Table height with safety support 1430 mm Lifting speed 1280 mm in 25 sec. Lowering speed 1280 mm in approx. 0 to 15 sec. Hydraulic operating pressure approx. 130 bar Motor power 1.5 kW Mains connection 400 Volt, 50 Hz. - Rotary switch switch on the hydraulic unit for up and down - lowering speed infinitely adjustable via throttle valve- 1 lifting cylinder hydraulic unit year of construction 2007 with tank adjacent - safety protection frame with limit switches net weight 660 kg good condition; used

Hydraulic scissor lift table HYWEMA type SHT / IN Fabr. No. 52-22330 Year of construction 1996 / 2022 Technically overhauled in 2022 load capacity 4 ton. Platform size 2300 x 1200 mm Stroke max. 1420 mm Construction height - table bottom 400 mm Construction height - table top max. 1820 mm Table height with safety support 1565 mm Lifting speed 1420 mm in 30 sec. Lowering speed 1420 mm in 45 sec. Motor power 4 kW Mains connection 400 Volt, 50 Hz - Hand switch for up and down on the cable - Circumferential safety edge for lowering shutdown - Hydraulics with tank mounted in the underframe- 1 piece lifting shears with two lifting cylinders - Steel plate mounted on the lifting frame 1200 x 1200 mm x thickness 20 mm Space requirement L x W x H 2300 x 1330 x 400 mm Net weight 1.4 ton. good condition; used

Hydr. Hacksaw, metal saw, lifting saw KASTO type PSB WBS 210 / 230 Masch. No. 115 106 1212 / 72783 Year of construction 1986 Saw area - round 250 mm Saw area - square 225 x 225 mm Saw area - rectangle 260 x 100 mm Cutting speed 11 -13 - 17 - 22 - 26 - 34 m/min. Saw blade length 400 mm Motor power 1.4 and 1.8 kW pole switchable Mains connection 380 Volt, 50 Hz - only for 90 cuts, no miter adjustment- Saw motor with 2 speeds and 3 V-belt steps - Hydraulic saw bracket feeding - Hydraulic cutting pressure adjustment via throttle valve - Rapid traverse for saw bracket lower - manually via handwheel height-adjustable material support table with mm scale - manual material tension - Coolant device in the machine foot - Operating instructions Space requirement L x W x H 1500 x 700 x 1550 mm Weight 590 kg very good condition; used

Freight lift according to MRL ConVer 147.01 with instructed accompanying person. Payload 1.200kg. 2 stops 0-4117mm. Car size 2800x2860x2000mm. Colour framework RAL 7043 Rest RAL 7035. Access bottom front top front and rear. Price without assembly, TÜV and freight, pure only the machine. The machine can also be adjusted on request, e.g. conveying height. Here, the selling price would then have to be determined.

Hydraulic scissor lift table GRUSE type ELS 0.5-8-1-G-SO Fabr. Product code: 124984 Year of construction 2017 Load capacity 300 kg Platform size 1250 x 800 mm Useful stroke max. 785 mm Height - table bottom 345 mm Construction height - table top 1130 mm Motor power 0.8 kW Mains connection 400 volts, 50 Hz - Foot switch for up and down, with emergency stop and key switch for control Single scissors with a lifting cylinder - circumferential safety contact strip with limit switches under the upper ramen - adjustable limit switch for the upper lifting restriction - table surface with sturdy wooden worktop and airliner rails with lashing eyes - hydraulic unit with tank mounted under the table- feet under the table corners, mobile with pallet truck own weight 430 kg very good condition, almost as new; used

Foil lifting device, details see pictures, immediately available

Lifting kneader lifting kneading machine Kemper F30 SL -Manufacturer: Emil Kemper GmbH -Model: F 30 SL -with stainless steel boiler and lifting arm -with automatic timer -2 speeds -with flour dust cover -mobile on wheels -with new timer

Lift-tilt device, lifting tipper Make Itec, type 2700, year of construction 2017 for accommodating 200- and 300-litre standard loading trolleys lifting capacity: 350 kg Tipping height: 2.231mm incl. 1 standard loading trolley 3x460V 50 Hz 0,75 kW - very good condition, hardly used - was used to feed a piston filling machine - Documentation/operating instructions available Visit in Korntal-Münchingen possible

Used lifting kneader DIOSNA, type: S 35 -In bakery condition- - for 35 kg dough - with timer -Dust cover - Machine runs smoothly - technically tested and cleaned - very nice condition Inspection and test run are of course possible by arrangement.

Lifting tipper Kemper HK 200 L for President Kessel -Lifting tipper from Kemper Emil Kemper GmbH -Type: HK 200 L -for Kemper President 125 A boiler -Year of construction August 2007 -tipping height approx. 260cm -Total height 345cm -400V 50Hz 3Ph

Electric pallet trucks SPECIFICATIONS: Drive: electric Drive system support Load capacity kg: 1000 Lifting height mm: 1600 Fork length mm: 1200

Traverse 3 meters Stroke: 350 KG

Demag Traverse Total length: 5.5 meters Gauge: 5.0 Meter Stroke: 250 KG

Used lifting kneader DIOSNA, type: S 20 3G -In bakery condition- - for 20 kg dough - 3 gears - Machine runs very smoothly - very nice condition Inspection and test run are of course possible by arrangement.

: Staplerhebebühne lifting capacity: 6600 kg weight of the machine ca.: 2,3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

- Lifting kneader Diosna S 35 - with stainless steel boiler - for max. 35 kg dough - with 2 speeds - with foot switch - with flour dust cover - Boiler diameter inside: 52cm - Inside boiler height: 35cm

Machine Mechanics & electrics prepared by an expert cleaned & functionally tested Advantages: + Stainless steel boiler + Lifting arm was freshly nickel-plated + with flour dust cap, with automatic switch-off when lifting + Lifting kneader for particularly dough-friendly kneading processes + with drilling devices for anchoring in the ground Specifications: - Flour capacity: max. 75 kg - Dough capacity: max. 120 kg - Boiler volume: approx. 180 litres - Motor power: 8 kW - Power loads: 380V - 3Ph - 50Hz - Fuse: 16A CEE plug

Lifting kneader lifting swaging machine Diosna D 200 Plus A used lifting kneader Diosna D 200 Plus is currently for sale and immediately available in our warehouse in Bielefeld. Lifting kneader Diosna D 200 Plus with fixed Kesel - with stainless steel boiler - Kettle for maximum 200 kg dough or for max. 125 kg flour - 2 speeds slow and fast - with flour dust cover - mobile on wheels - Machine completely repainted - with stainless steel control box - with 1 timer NEW - many parts renewed - Boiler polished - 380 volts

Lifting swaging machine Diosna S 120 Plus A used dough kneader Diosna S 120 for a maximum of 120kg dough, with 2 speeds, slow and fast is for sale and immediately available in our warehouse. Kneader Diosna S 120 - with 1 automatic timer - Machine is revised and repainted - with 2 gears - with stainless steel boiler - with flour dust cover - mobile on wheels with lock