127,137 used machines on RESALE, but how to find them? Machine Search
Hydraulic Pump Manufacturer : Rexroth / Brueninghaus Article: AL A6VM 355 HD2D / 63W 2-VZH157D B-S0167 Condition : New
6500ton Open Die Forging Press HJ / Seonam (Korea) Design: Eastern European Corporation Installation: 2006/2008 Press Type: Four column push down Oil hydraulic system Nominal force (static working pressure of 320 bar): 5,000 Tons Up-setting force (static working pressure of 420 bar): 6500 Tons Daylight: 5,200 mm Stroke of Movable cross head: 2,700 mm Main Ram dia. (Center cylinder): 1 set - ￠950 mm Side Ram dia. (Side cylinder): 2 sets - ￠750 mm Return cylinder Ram dia: 2 sets - ￠300 mm Moving Table Width: 2,600×Length 6,600 mm Moving Table stroke (center to both side 2,750mm): 5,500 mm Approaching speed: 300 mm/sec Main cylinder Forging speed (2,200 tons/ 320 bar): 163 mm/sec All cylinder Forging speed (5,000 tons/ 320 bar): 73 mm/sec Up-setting Forging speed (6,500 tons/ 420 bar): 10 mm/sec Return speed: 270 mm/sec Hydraulic Main pump: 12 sets ...
pressure: 130 t chamfer lenght: 3150 mm distance between columns: 2600 mm engine output: 15 kW control: CYBELEC VisiTouch weight of the machine ca.: 10900 kg dimensions of the machine ca.: 3990x1750x2900 mm Equipment: - Controlled axles: Y1, Y2, X, R, Z1, Z2, X1 - Fully dynamic, hydraulic crowning The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
hydraulic rope hoist, hoist, grab hoist, hydraulic cylinder for rope -hydraulically operated: cable pull -Max. Pulling force: 12 t -each: 1 pull cylinder with accessories -Number: 2 pieces -Price: per piece -Dimension: Ø 115 x 685 mm -Weight: 28 kg/piece
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Hydraulic cylinder: stroke 50 mm -Piston rod: Ø 40 mm -Mounting holes: Ø25 x 30 mm / Ø30 x 22 mm -Cylinder: outside Ø 105 mm -Dimensions: 380/145 / H105 mm -Weight: 12,2 kg
Offer 24295 Specifications: - max. working width 3050 mm - max. cutting capacity St 40 16 mm - Projection 270 mm - Cutting angle 2.4 ° - Cutting gap adjustment by hand - Number of hydraulic hold-downs 16 pcs - Motor back gauge with positioning control 20 - 1000 mm - Front angle stop + support arms - Stroke rate depending on cutting angle and cutting length 7 - 18 rpm - Hydraulic drive 400 V / 30 kW - Table height approx. 820 mm - Space required including back gauge, without front support arms -ca. W 4000 x H 2400 x D 2400 mm - Weight approx. 14500 kg - with: - E-foot switch - Cutting Line Illumination - - Cutting Length Selection - Rear area protection with light barrier
Key data: 30 t
Hydraulic press can be used in a variety of ways as an assembly press, small series press, manual insert press or heating press in double-column presses Design (H-press) A tour of the press is possible at the Ennepetal camp. It is a 2.5-year-old, unused press with no operating hours, which is sold with a full warranty. List price: 45,000 Technical details: Robust machine frame Capacity: 30 tons – at 300 bar Pump ASC: 28.5 liters/min. Engine: 11 kW – 15 hp Oil tank: 600 × 450 × 500 mm – with approx. 100 litres Cylinder piston: Ø 110 mm Cylinder inside: Ø 70 mm Stroke: 500 mm Fast forward: 45 mm/s Return: 55 mm/s Guides: Ø 50 mm Table top: 800 × 550 mm – with T-slots Plunger plate: 700 × 500 mm – with T-slots Total weight: 2000 kg Valves from BoschRexroth Control cabinet technology from renowned manufacturers Press table size 700 × 500 × 7 ...
Hydraulic pump, oil pump, gear pump, vane pump, hydraulic power unit -Manufacturer: VEM, hydraulic unit from Dorstener APE80-3050 press brake -Drive: VEB Type KMER 132 AC P 7.5 kW 1435 rpm -Flow rate: l/min -Operating pressure: bar -Dimensions: 720/340/H335 mm -Weight: 87 kg
feed under pressure: 2,7 mm/sec pressure: 100 t stroke: 400 mm table surface area: 920 x 560 mm feed down: 4,25 mm/sec feed up: 8,22 mm/sec oil pressure max. in the work cylinder: 385 bar oil volume: 26 l diameter of piston: 125 mm column daylight: 920 mm voltage: 400 V/ 50 Hz total power requirement: 4 kW weight of the machine ca.: 0,9 t dimensions of the machine ca.: 1,7 x 0,9 x 2,1 m • unused workshop press, • manual and hydraulical operation, • pressure cylinder horizontally moveable, • table can be hydraulically adjust in height, • Cylinder Ø 175 mm, piston base Ø 125 mm. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Qty. 1 Second-hand 160 MN Horizontal Direct Single Action Extrusion Press Mfc.: SMS Force: 16 000 MT Built: 2015/2016 Billet dim.: Dia. 610/720 x 750 – 2500 mm Scope of supply: Induction Billet Furnace Extrusion Press Quenching System Puller Run-Out Table Stretcher Finishing Saw Profile Stacker Die Oven Billet Peeling Machine
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Piston diameter: approx. 90 mm -Piston rod: Ø 40 mm -Diameter eyes: 35/35 mm -Stroke: 55 mm -Number: 2x cylinders available -Price: per piece -Dimensions: 485/120/H110 mm -Weight: 14 kg
Hydraulic pump, oil pump, gear pump -Max.: 600 rpm -Working pressure: 2 bar -Output: 3 l/min -Number: 1x pumps available -Price: per piece -Dimensions: 95/100/H90 mm -Weight: 2.3 kg
Key data: 2200 t
Qty. 1 Second-hand extrusion press – 2200 MT Mfc.: Breda Danieli Built: 2016 Status: still in production Max. Extrusion Force: 21,9 MN at 300 bar Max. working pressure: 310 bar Type of press: back loading with 2 containers Billet size 8” - length: 300 – 1,200 mm Scope of supply: complete extrusion press in working order with hydraulic and electric system Overhead pinch billet manipulator Material: AL 6000 Series Out of the scope of supply: floor frame mounted in the concrete floor all dies and tooling bolsters
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Single-acting: cylinder -Piston diameter: approx. 60 mm -Piston rod: Ø 45 mm -Stroke: 1530 mm -Cylinder comes from a Still forklift mast -universally applicable: -Number: 1x cylinder available -Price: per piece -Dimensions: 80/80/H1800 mm -Weight: 36 kg/piece
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Piston rod: Ø 25 mm -Tube: Ø outside 50 mm -Stroke: 140 mm -Total length: retracted 360 mm -Admission: hole Ø 20 mm -Dimensions: 360/50/H80 mm -Weight: 3.9 kg
Hydraulic cylinder, support cylinder, hydraulic ram, pressure ram, hydraulic hose -Hydraulic line: Hansa-Flex PHD240Tx2180AOLAOL45 -Hydraulic hose: HD240T 90 BAR -Price: per piece -Number: 2 pieces -Dimension: Ø 60 x 2020 mm -Weight: 7.1 kg/piece
Hydraulic cylinder, support cylinder, hydraulic piston, pressure piston -Manufacturer: Orsta, hydraulic cylinder type 4514-3328/0 Pn12 -Stroke: 404 mm -Piston rod: Ø 35 mm -Cylinder: Outer Ø 106 mm -Mounting: Bolt circle Ø 180 mm -Dimensions: 910/220/H220 mm -Weight: 30 kg
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams, tilt cylinders -Manufacturer: FXMeiller, hydraulic cylinder / tilt cylinder stroke 670 mm -Piston rod: Ø 45 mm / holder Ø 40 mm -Recording cylinder: Ø 50 x 45 mm -Cylinder: outside Ø 102 mm -Dimensions: 1055/210 / H180 mm -Weight: 50 kg
Nominal force 1250 ton - first stage : 260 tons, - second stage : 800 tons, - third stage : 1250 tons, Slide stroke 1250 mm Distance between table and slide 2650 mm Main cylinder dia Ø 500mm Return cylinder dia. ( two) 2xØ400mm Distance between column 1800mm Table size width / length 1250 / 3150 mm Main motor power 150 kW Machine dimensions L x W x H 16950 x 12100 x 11410 mm Weight 265000 kg Forging manipulator FS2ЕТС -2T also available 1T and 700t
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Hydraulic cylinder: stroke 60 mm -Piston rod: Ø 20 mm / bore Ø 8 mm -Cylinder: outside Ø 90 mm -Admission: bolt circle Ø 124 mm -Number: 2x cylinders available -Price per piece -Dimensions: Ø 150 x 435 mm -Weight: 16 kg / pc.
Hydraulic cylinder, support cylinder, hydraulic ram, pressure ram, center mower lifting cylinder -Hydraulic cylinder: stroke 200 mm -Piston rod: Ø 23 mm / thread Ø22 x 50 mm -Mounting: Ø20 x 32 mm -Cylinder: outside Ø 62 mm -Dimensions: 770/70/H62 mm -Weight: 7.2 kg
Hydraulic cylinder, support cylinder, hydraulic piston, pressure piston, center mower lifting cylinder -Hydraulic cylinder: stroke 105 mm -Piston rod: Ø 23 mm -Recordings: Ø20 x 22 mm -Cylinder: outer Ø 58 mm -Dimensions: 475/70/H75 mm -Weight: 5.7 kg
to move the heaviest loads Total thrust 400 to - 4 x 100 to Cylinder stroke approx. 1,000 mm Double-acting hollow piston cylinders Tie rods 9 x 6,000 mm, 1 x 5,000 mm Operating pressure up to 400 bar Tank capacity approx. 500 litres Operation via wired remote control Electrical values 400 V / 2 x 30 KW
Hydraulic power pack, hydraulic pump, hydraulic pump, universal power pack -Hydraulic unit: from Heycop 3UN/2000 automatic lathe -Motor: Siemens 1.5 kW/2855 rpm -Hydraulic tank: with level indicator -Pressure display: up to 60 bar -Dimensions: 300/500/H650 mm -Weight: 130 kg
Hand hydraulic pump, hand pump, hydraulic cylinder, hydraulic hand pump -Hand hydraulic pump: with cylinder, unfortunately no type designation -Stroke: 45 mm -Piston rod: Ø 32 mm -Dimensions: see drawing in the photos -Dimensions: 645/230/H480 mm -Weight: 50 kg
pressing pliers, crimping pliers, cable lug pliers, hydraulic crimping pliers -Manufacturer: Orsta, hydraulic pressing tongs -Use: for large cable lugs -Hydraulic connection: see photo -Dimensions: Ø 118 x 315 mm -Weight: 11.2 kg
Payload 10,000 kg Rope diameter 22 mm x 150 meters length as specified in the documentation Operating pressure 55 bar to max. 80 bar Flow rate 19 litres / min to max. 272 litres / min Rexroth hydraulic motor Hydraulic control block with mounting base Documentation and test book available The winch was used on a test bench / test tower. Space requirement L - 2,100 x D - 1,400 x H - 1,300 mm complete with control block Weight approx. 1,500 kg
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Piston rod: Ø 32 mm -Stroke: 140 mm -Total length retracted: 460 mm -Admission: hole Ø 23 mm -Dimensions: 460/60/H135 mm -Weight: 8.5 kg
Hydraulic cylinder, support cylinder, hydraulic piston, pressure piston -Hydraulic cylinder: stroke 155 mm -Piston rod: Ø 70 mm -Hole: Ø70 x 70 mm -Cylinder: outer Ø 120 mm -Dimensions: 865/160/H160 mm -Weight: 53 kg
hydraulic outriggers for loader cranes Stroke 500 mm Stable design with guide via square tube Mechanically telescopic with bolt 300 mm - grid 100 mm Outer square tube 100 x 100 mm Folding device for support cylinder - can also be dismantled Outriggers can be folded down approx. 60° Retracted height 1,000 mm with folding device with integrated load holding valve Removable support plate - size 320 x 250 mm Weight 80 kg / piece - New - unused - 2 pieces in stock - unit price -
Quick clamping device, hydraulic clamping device, electro-hydraulic clamping device, -Manufacturer: WMW HECKERT, clamping device from milling machine FSS 315-V -Type: FHKN 3311 -Motor: VEM 0.12 kW -Dimensions: 440/150 / H220 mm -Weight: 24 kg
Hydraulic cylinder for ATLAS loader crane Stroke 750 mm Piston rod 125 mm Outer diameter cylinder tube 235 mm Piston diameter approx. 200 mm Length retracted center - center bolt 1,100 mm Bolt diameter cylinder tube 80 mm Width of the mount 245 mm Bolt diameter 100 mm Both bolt mounts with plain bearings Spare part number original Atlas 4189526 Width of the piston rod holder 130 mm Weight approx. 330 kg / piece Original price approx. € 9,500,-- -New- - 2 pieces in stock - price per piece -
Inv. Num. : 8131 Type: HPD-S 63 Producer: Hydrap Created: 1997 Parameters: Compressive force: 63 t Stroke: 1000 mm Maximum lifting speed: 410 mm/s Machine height: 2200 mm Machine length: 1200 mm Machine width: 500 mm Machine weight: 13000 kg
pressure: 200 t stroke: 150 mm table surface area: 850x650 mm ram surface: 730x560 mm weight of the machine ca.: 8 t dimensions of the machine ca.: BxTxH 2000x2500x3600mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 40 t throat: 320 mm stroke: 250 mm arm length: 320 mm table surface area: 1400x600 mm ram surface: 1200x600 mm dayligth: 650 mm total power requirement: 22 kW weight of the machine ca.: 8 t dimensions of the machine ca.: 3200x3300x3300 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 t throat: 380 mm stroke: 300 mm arm length: 380 mm table surface area: 1700x700 mm ram surface: 1400x700 mm dayligth: 650 mm total power requirement: 30 kW weight of the machine ca.: 10 t dimensions of the machine ca.: 2400x3600x3400 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Piston diameter: Ø 60 mm -Piston rod: Ø 35 mm -Flange: Ø 69 mm -Recording thread: Ø 22 x 2 x 30 mm -Stroke: 900 mm -Dimensions: 1090 x 100 x 100 mm -Weight: 17 kg
pressure: 25 t stroke: 100 mm table surface area: 440x320 mm ram surface: 360x220 mm hole in the table: 160x100 mm table height: 900 mm tool hole in ram: Ø 40 mm dayligth: 280 mm weight of the machine ca.: 1,5 t dimensions of the machine ca.: BxTxH 1500x1500x2100 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 t throat: 380 mm stroke: 400 mm power capacity: 22 kW dayligth: 600 mm ram surface: 600x500 mm table surface area: 720x600 mm weight of the machine ca.: 9 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Hydraulic cylinder, support cylinder, hydraulic ram, pressure ram, hydraulic hose -Hydraulic line: Hansa-Flex PHD240Tx1080SF50VASF5045 -Hydraulic hose: HD240T 90 BAR -Dimension: Ø 58 x 1100 mm -Weight: 4.5 kg
pressure: 25 t throat: 250 mm stroke: 100 mm ram surface: 500x400 mm hole in the table: Ø 110 mm table height: 850 mm tool hole in ram: Ø 40 mm ram surface: Ø 150 mm weight of the machine ca.: 2,5 t dimensions of the machine ca.: 1500x2000x2200 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 200 t distance between columns: 500 mm stroke: 150 mm ram surface: 320 mm table surface area: 470x400 mm weight of the machine ca.: 12 t dimensions of the machine ca.: 2000x2000x2700 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Hydraulic filter, filter element -Manufacturer: Hydac, filter element Betamicron OVP -Type: 2600 R 005 BN4HC -Dimension: Ø 143 x 920 mm -Weight: 6.4 kg
pressure: 25 t distance between columns: 580 mm stroke: 150 mm dayligth: 370 mm table surface area: 560x400 mm ram surface: 400x350 mm hole in the table: 80 mm weight of the machine ca.: 2,5 t dimensions of the machine ca.: 1500x500x2500 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 160 t distance between columns: 850 mm stroke: 400 mm ram surface: 800x700 mm : 300 mm pressure of ejector: 20 t table surface area: 800x700 mm total power requirement: kW weight of the machine ca.: 12 t dimensions of the machine ca.: 1800x1800x4200 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Hydraulic motor VICKERS 2520V12A8 Shaft diameter: Ø 22 mm Flange diameter ( inside ): 102 mm Bolt circle diameter: Ø 115 mm New ! Dimensions: 310 x 175 x 160 mm
pressure: 100 t passage width: 810 mm stroke: 400 mm table surface area: 1140x740 mm ram surface: 1140x740 mm dayligth: 670 mm weight of the machine ca.: 8 t dimensions of the machine ca.: 1800x1800x3000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Hydraulic pump HUGRABPUKA A10X pressure: 17.5 MPa 1500 rpm New ! Dimensions:130 x 90 x 115 mm
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Hydraulic cylinder: from automatic band saw Behringer HBP -Piston rod: Ø 22 mm -Stroke: 445 mm -Admission piston rod: M12 -Dimensions: 605/100/H85 mm -Weight: 8.7 kg
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Spare part: hydraulic cylinder from Amada HA-400W metal saw -Piston rod: Ø 28 mm -Stroke: 585 mm -Admission piston rod: M30 x 1.5 -Dimensions: 835/70/H200 mm -Weight: 17.1 kg
maximum number of results exceeded
please refine your search
