134,408 used machines on RESALE, but how to find them? Machine Search
Moulding machine Ital Form Completely made of stainless steel 2 cylinders Rollers 500 mm long Dimensions: 820x900x1200mm Electric power: 0.75kW Voltage: 400V, 3 PH. 50 Hz Weight: 155 kg
Moulding machine Ital Form 4 cylinders Rollers 500 mm long Dimensions: 850x1200x1150mm Electric power: 0.75kW Weight: 170 kg
Injection Unit Screw Diameter: Ø 55 Injection Volume: approx. 517 cm³ Injection Pressure: up to 2,000 bar Injection Rate: approx. 220 cm³/s Plasticizing Capacity: approx. 35 g/s (PS) Screw L/D Ratio: 22:1 Nozzle Contact Force: 60 kN Clamping Unit Clamping Force: 2,300 kN (230 t) Clamping System: Zhafir Zeres all-electric toggle system Platen Size (H × V): approx. 850 × 800 mm Mould Opening Stroke: 470 mm Max. Daylight Opening: approx. 940 mm Min. Mould Height: 220 mm Ejector Stroke: 150 mm Ejector Force (fwd / back): 50 / 30 kN Drive & Control Drive Type: All-electric servo drive Installed Power: 47 kW Full Load Current: 79 A Short Circuit Current: 25 kA Power Supply: 400 V / 50 Hz / 3-phase Control System: Zhafir SIGMATEK HMI touchscreen control Equipment / Features Drive Concept: Fully electric servo system for high p ...
Injection Unit Engine not working Screw Diameter: 65 Ø Injection Volume: approx. 1,025 cm³ Injection Pressure: up to 1,800 bar Injection Rate: approx. 450 cm³/s Plasticizing Capacity: approx. 80 g/s (PS) Nozzle Contact Force: 100 kN Clamping Unit Clamping Force: 5,000 kN (500 t) Clamping System: ENGEL Duo two-platen design Platen Size (H × V): approx. 1,300 × 1,200 mm Mould Opening Stroke: 800 mm Max. Daylight Opening: approx. 1,400 mm Min. Mould Height: 400 mm Ejector Stroke: 200 mm Ejector Force (fwd / back): 90 / 60 kN Drive & Control Drive Type: Servo-hydraulic (ecodrive inside) Hydraulic System Pressure: up to 160 bar Pump Motor Power: 37 kW Total Installed Power: approx. 55 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL CC300 touchscreen control Equipment / Features Clamping System: Two-platen design f ...
Injection Unit Screw Diameter: Ø 65 Injection Volume: approx. 1,075 cm³ Injection Pressure: up to 1,750 bar Injection Rate: approx. 400 cm³/s Plasticizing Capacity: approx. 85 g/s (PS) Nozzle Contact Force: 110 kN Clamping Unit Clamping Force: 5,500 kN (550 t) Clamping System: ENGEL Duo two-platen design Platen Size (H × V): approx. 1,350 × 1,300 mm Mould Opening Stroke: 850 mm Max. Daylight Opening: approx. 1,450 mm Min. Mould Height: 400 mm Ejector Stroke: 220 mm Ejector Force (fwd / back): 95 / 65 kN Drive & Control Drive Type: Hydraulic (pre-ecodrive generation) Hydraulic System Pressure: up to 160 bar Pump Motor Power: 45 kW Total Installed Power: approx. 65 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL EC88 digital control panel Equipment / Features Clamping System: Robust two-platen design for hi ...
Clamping force: 800kN, tie-bar spacing: 400mm, injection unit: 430, max. flow rate: 76l/min, max. hydraulic pressure: 210bar, control: CDIAS, weight: 3.6t, an on-site inspection is possible.
Clamping force: 1250kN, tie-bar spacing: 475x450mm, injection unit: 440, max. flow rate: 100l/min, max. hydraulic pressure: 190bar, weight: 6.6t, an on-site inspection is possible.
Clamping force: 1600kN, width: 1600mm, height: 2200mm, weight: 6.8t, an on-site inspection is possible.
Clamping force: 650kN, length: 4000mm, width: 1600mm, height: 2200mm, weight: 3.9t, an on-site inspection is possible.
Block moulding machine Type: 860 AZ Manufacturer: Zenith Year: 1988 The board machine has been operated continuously at the same location since it was commissioned in 1988. For sale is not only the block machine itself but also the entire production line. The system can be used in full after purchase. The block machine was operated in a two-shift system until the end of 2023 and was then decommissioned. The plant is still complete and can be inspected at any time upon request. MACHINE DATA Block forming machine: Board machine from manufacturer Zenith, type 860 AZ, year of manufacture 1988 Production of core and face mix Control system: Simatic S5 with Zenith visualization Board size: 1,400 × 950 mm Maximum product height: 14 cm Quick mould clamping system, pneumatic Production line: Hydraulic pusher with proportional valves on the wet side Elevator with chain transport, ...
Key data: 450 mm, 63 , 25
Screw diameter: 25 mm Displacement: 69 cm³ Injection weight in polystyrene: 63 g/hp Injection pressure: 2,400 bar Clamping force: 45 t tie-barless Tool installation height min.: 175 mm Opening distance: 355 mm CONTROL: CC200 Screen text: german / german Instruction manual: german / german Sprue picker er/usp Pump drive power: 11 kW Total connected load: 17.8 kW Total weight: 3,300 kg Dimensions L x W x H: 3.3 x 1.2 x 2.0 m m m Payment terms: 100% before taking over the machine, net only
Clamping force: 1500kN, rated current: 133A, connected load: 74kW, an on-site inspection is possible.
Clamping force: 800kN, an on-site inspection is possible.
Electrical injection moulding machine manufactured in 2005. This Husky Hylelectric H1000 RS95/80 features a clamping force of 10,000 kN and a maximum injection pressure of 2280 bar. It has a total platen size of 2070 x 1840 mm and a screw diameter of 80 mm. If you are looking to get high-quality injection moulding capabilities, consider the Husky Hylelectric H1000 RS95/80 machine we have for sale. Contact us for further details.
Electrical injection moulding machine manufactured in 2005. This Husky Hylelectric H1000 RS95/80 features a clamping force of 10,000 kN and a total platen size of 2070 x 1840 mm. It has a maximum injection pressure of 2280 bar and a screw diameter of 80 mm. If you are looking to get high-quality injection moulding capabilities, consider the Husky Hylelectric H1000 RS95/80 machine we have for sale. Contact us for further details.
Various injection molding machines are available. 1) Arburg Allrounder 420 A 1000-400, clamping force: 100t, screw diameter: 30/35mm, year of manufacture: 2005. 2) Demag 1000-420-310 EL-Exis S, clamping force: 100t, screw diameter: 30mm, year of manufacture: 2003. 3) Demag 1000-420-200 EL-Exis S, clamping force: 100t, screw diameter: 25mm, year of manufacture: 2003. 4) Arburg 570 C 2000-150/60 2K, clamping force: 200t, screw diameter: 25/12+15mm, year of manufacture: 2007. 5) Arburg 420 C 1000-250, clamping force: 100t, screw diameter: 35mm, year of manufacture: 1996. 6) Arburg 420 C 1000-250, clamping force: 100t, screw diameter: 30/25mm, year of manufacture: 1995. 7) Arburg 420 C 1000-250, clamping force: 100t, screw diameter: 30mm, year of manufacture: 1994. 8) Netstal Synergy 600-110, clamping force: 60t, screw diameter: 25mm, year of manufacture: 2001. 9) Arburg 900T 800-150, clampi ...
Manufacturer: ARBURG Model: ALLROUNDER 680 Year of Manufacture: 2016 Type of Machine: Injection Moulding Machine Electrical Specifications: - Operating Voltage: 400 V, 3-phase, 50 Hz - Control Voltage: 230 V ~ / 24 V = - Motor/Heating Rated Current: 76 A / 18 A - Total Rated Current: 94 A - Total Connected Load: 56 kW Machine has already been dismantled Operating hours: à approx. 29,000 hours Find more here - .ucymachines/ Contact us at - sales@ucymachines
Two Battenfeld injection molding machines are available. 1) Battenfeld BA 1600, year of construction: 2001, clamping force: 1600kN, tie bar distance: 520mm/520mm, installation height min./max.: 225mm/550mm, opening stroke: 480mm, centering diameter: 160mm, screw diameter: 50mm, injection weight: 520g. 2) Battenfeld BA 500/200 CDK, year of construction: 1995, clamping force: 500kN, tie bar distance: 320mm/320mm, platen dimensions X/Y: 490mm/490mm, installation height min./max.: 150mm/350mm, opening stroke: 250mm, max. platen distance: 600mm, screw diameter: 35mm, injection volume: 134.7cm³, injection weight: 122.5g, injection pressure: 1484bar. Machine dimensions X/Y/Z: approx. 3800mm/1350mm/1800mm, weight: approx. 3200kg. The machine has cylinder problems with the screw and the forward/backward unit. Documentation available. On-site inspection is possible. Individual sale possible.
Two complete injection molding plants with two Husky injection molding machines, four complete moulds with all-metal separator, Motan gravimetric mixing system and crane system are available. 1) 2x Husky H-PET230 AE RS95, year of manufacture: 2015, max. shot weight: 2424g, max. PET throughput: 390kg/h. 2) 48-cavity H-PET mold, preform weight: 17.8g, length: 89.35mm, wall thickness: 3.06mm, base thickness: 2.30mm, cavities: 48, cycle time: 12.1s-12.7s. 3) 48-cavity H-PET mold, preform weight: 30.26g, length: 122.3mm, wall thickness: 3mm, base thickness: 2.3mm, cavities: 48, cycle time: 14.4s-15s. 4) 32-cavity H-PET mold, preform weight: 18g, length: 82.04mm, wall thickness: 2.7mm, base thickness: 2.2mm, cavities: 32, cycle time: 11s-11.7s. 5) 32-cavity H-PET mold, preform weight: 29g, length: 108.59mm, wall thickness: 3.16mm, base thickness: 2.42mm, cavities: 32, cycle time: 13.4s-14s. To ...
A Ferromatik Milacron injection molding machine without additional and peripheral equipment is available. Clamping force: 1000kN, injection pressure: 2000bar, stroke volume: 254cm³, heating capacity: 14.8kW, tie bar distance: 508mm, machine weight: approx. 6750kg, operating hours: approx. 33649h. On-site inspection is possible.
Key data: 3200 kN, 359 g/PS, 50 mm
1.0 St. gebr. Two-component injection molding machine Manufacturer: ARBURG Type: 720A3200-800/70 Year of Make: 2017 Clamping force: 320 tons Spar spacing 720 x 720 mm Installation height min./max.: 300 - 800 mm Opening travel: 600 mm Screws DN 1: 50 mm Max. displacement: 392 cm³ Moulded part weight in hp: 359 g Screw DN 2: 22 mm Max. displacement: 34 cm³ Moulded part weight in hp: 31 g Control: Selogica Request technical equipment.
Two injection moulding machines Krauss Maffei are available. 1) Krauss Maffei KM 50 C1, year of manufacture: 1999, injection unit: SP220, screw diameter: 30mm, L/D ratio: 23, injection pressure: 2500bar, shot volume: 85cm³, machine dimensions X/Y/Z: approx. 3200mm/1350mm/1800mm, weight: approx. 2500kg, control: MC4, operating hours: approx. 86000h. 2) Krauss Maffei KM 125 C1, year of manufacture: 2000, injection unit: SP520, screw diameter: 45mm, L/D ratio: 20, injection pressure: 1878bar, shot volume: 217cm³, machine dimensions X/Y/Z: approx. 4500mm/1550mm/2200mm, weight: approx. 5500kg, control: MC4, operating hours: approx. 82000h. Documentation available. An on-site inspection is possible.
Clamping force: 1500kN, screw diameter: 50mm, tie bar spacing: 500mm, platen dimensions X/Y: 780mm/790mm, opening stroke: 600mm, daylight: 900mm, ejector stroke: 150mm, shot volume: 305cm³, injection weight: 278g, injection pressure: 2336bar. Machine dimensions X/Y/Z: approx. 4700mm/1550mm/2200mm, weight: approx. 7000kg, control: MC4. Includes Sepro handling system. Documentation available. An on-site inspection is possible.
Two injection moulding machines are available. 1) Ferromatik K 110 1100-493, year of manufacture: 2000, clamping force: 1100kN, min. mould installation height: 300mm, max. opening stroke: 550mm, screw diameter: 40mm, injection volume: 201cm³. The control no longer starts up properly, probably due to the circuit board. Includes a 3-axis handling robot Remak. Without conveyor belt. 2) Arburg 270 M 500-90, year of manufacture: 1995, clamping force: 500kN, min. mould installation height: 225mm, max. opening stroke: 325mm, screw diameter: 30mm, injection volume: 70cm³. The cylinder is slightly leaking. Documentation available. An on-site inspection is possible.
Clamping force: 220kN, min. mould height: 200mm, max. opening stroke: 200mm, max. platen distance: 400mm, ejector stroke: 80mm, machine dimensions X/Y/Z: approx. 2600mm/800mm/1600mm, weight: approx. 760kg. An on-site inspection is possible.
An almost like-new injection moulding machine Arburg is available. Clamping force: 1600kN, tie bar distance: 520mm, clamping stroke: 364mm, ejector stroke: 150mm, ejector force: 40kN, injection unit: 400, injection pressure: 2500bar. Machine dimensions X/Y/Z: approx. 6000mm/1800mm/2200mm, weight: approx. 6000kg, control: Selogica, operating hours: approx. 67h. Includes enclosure with clean air supply FilterFanUnit and removal robot. Documentation available. An on-site inspection is possible.
Ref. no.: 18255 Manufacturer: ENGEL Year of construction: 2004 Clamping unit Clamping force: 180 ton Opening stroke: 750 mm Distance between tie bars: 960 x830 mm Mould height min.: 500 mm Opening width: 1250 mm Injection unit Screw diameter: 45 mm Injection volume: 318 cm³ Shot weight: 302 g Injection pressure: 1769/2360 bar Measurements and weight Machine weight: 13500 kg Robot Producer: Wittman Type: W743 Year: 2009 Further information: ENGEL Victory 750/180 Tech – Power, Flexibility and Reliability with Tie-Bar-Less Technology The ENGEL Victory series was specially developed for technical plastic processing and is known as a professional injection moulding machine series offering high energy efficiency and maximum mould flexibility. Unlike conventional tie-bar machines, this series provides a much more flexible working area thanks to its tie-bar-less clamping system. ⸻ Advanta ...
Ref. no.: 18591 Manufacturer: ARBURG Year of construction: 2005 Clamping unit Clamping force: 160 ton Opening stroke: 450 mm Distance between tie bars: 520 x 520 mm Mould height min.: 250 mm Mould height max.: 550 mm Opening width: 700 mm Platen size (h x v): 695 x 695 mm Injection unit Screw diameter: 45 mm Injection volume: 254 cm³ Shot weight: 232 g Injection pressure: 1580 bar Measurements and weight Machine weight: 7100 kg Dimensions LxWxH part 1: 5,1 x 1,7 x 2,3 m Further information: The ARBURG 520 A series is part of the fully electric ALLROUNDER range and is known for its high precision, energy efficiency, and reliability in injection molding processes. These machines are particularly suitable for the production of technical plastic parts with high quality requirements, as well as for applications where repeatability and process stability are essential. Typical features of this ...
Ref. no.: 18092 Manufacturer: ENGEL Year of construction: 2001 Clamping unit Clamping force: 300 ton Opening stroke: 855 mm Platen size (h x v): 1050 x 650 mm Injection unit Screw diameter: 60 +35 mm Injection volume: 735 +135 cm³ Shot weight: 662 + 122 g Injection pressure: 1834 +1620 bar Measurements and weight Dimensions: 7,75 x 2,35 x 2,6 m Machine weight: 24780 kg Further information: ENGEL ES 1350H200W/300HL-2F — 2K Injection Moulding Machine This machine from the prestigious Austrian manufacturer ENGEL, built in 2001, features a clamping force of 300 tonnes and a true 2K L-configuration in horizontal layout. Motor and Hydraulic System The machine is equipped with a powerful electric motor coupled to a high-pressure hydraulic pump group. The electric motor continuously drives the hydraulic pump, providing pressurised oil flow throughout the entire system. This pressurised oil fe ...
An Arburg injection molding machine with integrated rotary table is available. Connected load: 61kW, clamping force: 500kN, opening force: 40kN, opening stroke: 250mm, max. mold installation height: 270mm, platen distance: 520mm, rotary table diameter: 900mm, rotation angle: 180°, max. table load: 240kg, max. injection pressure: 2500bar. Machine dimensions X/Y/Z: approx. 3250mm/2000mm/2600mm, weight: approx. 3200kg, operating hours: 6244h. Documentation available. An on-site inspection is possible.
Eight Arburg injection molding machines, one Engel injection molding machine, and one Demag injection molding machine are available. 1) Arburg 270M 350-90, year of manufacture: 1996, operating hours: approx. 110000h. 2) Arburg 270M 350-90 U, year of manufacture: 1998, operating hours: approx. 108000h. 3) Arburg 270M 350-90, year of manufacture: 1992, operating hours: approx. 178000h. 4) Arburg 420C 1000-250, year of manufacture: 1995, operating hours: approx. 96000h. 5) Arburg 370C 800-225, year of manufacture: 1992, operating hours: approx. 156000h. 6) Arburg 320M 500-90, year of manufacture: 1991, operating hours: approx. 94000h. 7) Arburg 270M 350-90 U, year of manufacture: 1998, operating hours: approx. 83000h. 8) Arburg 630S 2500-675, year of manufacture: 2003, operating hours: approx. 93000h. 9) Demag Viva 100-400, year of manufacture: 1999, operating hours: approx. 116000h. 10) En ...
Injection moulding machine for food and beverages caps
Injection moulding machine for PET preforms
Clamping Force: 150 ton // Mould Height (Max): 730 mm
Injection moulding machine for food and beverages caps
Injection moulding machine for PET preforms
Injection moulding machine for PET preforms
Number Of Stations: 32 // Output (caps/min): 500
Number Of Stations: 24 // Output (caps/min): 600
used
Some older plastic injection molding machines from Arburg, Demag and Stübbe are available. 1) Stübbe S110/345, year of manufacture: 1976, clamping force: 1000kN, shot weight: 140g, mold installation height min./max.: 180mm/480mm, opening stroke: 320mm, tie bar spacing: 360mm/355mm, screw diameter: 40mm, core pulls: 1. 2) Demag D 150-452 NC III, year of manufacture: 1990, clamping force: 1500kN, shot weight: 207g, mold installation height min./max.: 320mm/550mm, opening stroke: 430mm, tie bar spacing: 460mm/460mm, screw diameter: 45mm, core pulls: 1. 3) Demag D 100-275 NC II P, year of manufacture: 1989, clamping force: 1000kN, shot weight: 130g, mold installation height min./max.: 200mm/400mm, opening stroke: 350mm, tie bar spacing: 400mm/400mm, screw diameter: 38mm, core pulls: 1. 4) Arburg Allrounder 270M 250-75, year of manufacture: 1990, clamping force: 250kN, shot weight: 25g, mol ...
Key data: 1500 kN
Clamping force: 150 t. Clamping type: Toggle system. Tie-bar spacing: 470 × 470 mm. Platen size: 700 × 700 mm. Mold height (min–max, approx.): 180–500 mm. Opening stroke: 420 mm. Ejector stroke: 130 mm. Injection volume: 320 cm³. Screw diameter: 42/45 mm (to be confirmed). Heating zones: 4. Machine dimensions: 5000 × 1400 × 2000 mm. Machine weight: 6000–7000 kg.
Key data: 2000 kN, 352 g/PS, 50 mm
1.0 St. gebr. Two-component injection molding machine with robot Manufacturer: ENGEL Type: ES650H/200W-200HL-2F Year of Make: 2000 Clamping force: 200 tons Tiebar spacing sparless Min. installation height: 450 mm Opening travel: 700 mm Screws DN 1: 50 mm Max. displacement: 392 cm³ Moulded part weight in hp: 352 g Screw DN 2: 25 mm Max. displacement: 69 cm³ Moulded part weight in hp: 60 g Control: CC200 Technical equipment: -Engel robot, type: ERC23/1-E -4 core slides -Turntable control
Key data: 2000 kN, 216 g/PS, 40 mm
1.0 St. gebr. Two-component injection molding machine with robot Manufacturer: ENGEL Type: ES650H/200W-200HL-2F Year of Make: 2001 Clamping force: 200 tons Tiebar spacing sparless Min. installation height: 550 mm Opening travel: 700 mm Screws DN 1: 40 mm Max. displacement: 251 cm³ Moulded part weight in hp: 216 g Screw DN 2: 25 mm Max. displacement: 69 cm³ Moulded part weight in hp: 60 g Control: CC200 Technical equipment: -Engel robot, type: ERC23/1-E -4 core slides -Turntable control
Key data: 2000 kN, 216 g/PS, 40 mm
1.0 St. gebr. Two-component injection molding machine with robot Manufacturer: ENGEL Type: ES650H/200W-200HL-2F Year of Make: 2004 Clamping force: 200 tons Tiebar spacing sparless Min. installation height: 500 mm Opening travel: 750 mm Screws DN 1: 40 mm Max. displacement: 251 cm³ Moulded part weight in hp: 216 g Screw DN 2: 25 mm Max. displacement: 69 cm³ Moulded part weight in hp: 60 g Control: CC200 Technical equipment: -Engel robot, type: ERC23/1-E -4 core slides -Turntable control
A fully equipped Arburg injection molding machine including clean air supply Filter Fan Unit and removal robot is available. Clamping force: 1600kN, screw diameter: 45mm, max. cylinder heating: 450°C, total connected load: 85.5kW, machine elevation: 100mm, operating hours: approx. 9171h. Arburg Multilift H: axis: B, Z-axis stroke: 1400mm, conveyor belt length: 2500mm, conveyor belt width: 600mm, deposit height range: 900mm-1300mm, temperature resistance: 160°C. Documentation available. An on-site inspection is possible.
A vertical injection molding machine Arburg with a horizontal injection unit is available. Clamping force: 800kN, opening stroke: 500mm, min. mold installation height: 250mm, platen spacing: 750mm, tie bar spacing X/Y: 420mm/420mm, platen dimensions X/Y: 570mm/570mm, max. mold weight: 600kg, ejector stroke: 175mm. Machine dimensions X/Y/Z: approx. 4350mm/1700mm/2100mm, weight: approx. 3500kg. Documentation available. On site inspection is possible.
This MAPLAN MFT 750/160 edition S was manufactured in 2016. It is a vertical injection moulding machine, ideal for precision plastic processing. Contact us for more information.
maximum number of results exceeded
please refine your search
48.960 € 
