bending roll used for sale

Tool cabinet for press brake Good for WILA / TRUMPF tools or Type B L / W / H: 1180 mm x W 850 mm / H 1200mm, 350kg -ausziehbare drawers, allows the double-sided access to the tools -beliebige height adjustment of shelves -robust steel construction, powder coated -Lateral fork guide rails for transporting by forklift (cavity under the cabinet) -The drawers run on Rollengleitschienen (serve as additional stabilization) -The cabinet can be dismantled - Number of drawers: 4 pieces - Dimensions of drawer: - Total height 1200mm / 850mm total width / total depth 1180mm - Dimensions of the compartments in a drawer: - Fachhhoehe adjusted to 210mm (is varriabel) - Trade Height total usable ohnen shelves 990mm - Trade width 130mm available - Trade depth usable 1100mm - Number of shelves: 4 pieces / completely continuous; "ready for operation"

Max bending length: 1020 mm Max. sheet metal rod: 2 mm steel motor upper cheek adjustment via foot switch manual rear stop diverse bending rails

Punching and forming center in chain with an assembly line for the production of relays, see pictures

Machine number: ST-R-1660 Buerstentgratmaschine for the deburring of metal sheets or plates Power supply: 380 V 50 Hz 1.0/1.4 kW 2 speeds: 1500-3000 rpm. Brush diameter: 250 mm

SHUZ TUNG CNC 50 BRM CNC tube and profile bending machine built in 2014 in Taiwan allows for fully automatic, serial production of complex spatial workpieces in 5 axes with simultaneous hole punching. Excellent precision and accuracy of bending are guaranteed by the reliable servo motors used in the machine, which are responsible for realising the main working movements, i.e. bending, rotation and material feed. The rest of the movements are driven by a central hydraulic system with electronic lubrication. The SHUZ TUNG CNC mandrel bending machine is operated via a control panel with an installed CNC controller with the option of saving an unlimited number of programmes. In addition, the automatic servo bending machine is equipped with several bending rolls, a high-quality mandrel and an actuator to support material feed. The 50 BRM automatic CNC mandrel bending machine weighs 3500 kg ...

Technical data: -maximum working length 1250 mm -Stand round 1050 mm -Max pressing force 80 t -Stroke 250 mm -Stand RADIUS 300 mm -Max height betw. Table - press bar 560 mm -Lifting speeds -Backward speed idle max 100 mm / sec. -Forward speed 100 mm / sec. -Backward press speed max. 12 mm / sec. -Total power 15 kW -Space requirement approx. B 1750 x H 3400 X 2000 mm -Weight approx. 8500 kg -with: - CNC - control CYBELEC DNC 7400 PSGY -controlled X - axis back gauge 5-1000 mm -Pneum. Z - axis in three stages. height-adjustable -manually movable and foldable stop fingers -controlled pneumatic die shift - hydr. Tool clamping -Manual crowning - 2 piece support arms -Pointed tool shared H 320 x L 1000 mm -Foot tool H 320 mm x L 1000 mm - universal matrix L 1000 mm

Technical data: -Pressure capacity 2000 kN -Max working width 3100 mm -Stand round 3200 mm -Stand RADIUS 300 mm -Max mounted height 965 mm -Hub, or insertion depth Steplessly adjustable 0-400 mm -Plunger speed forward + reverse per 100 mm / sec -Operating speed in 9 steps selectable 1-10 mm / sec -Drive 400 V / 26.5 kW - space requirement approx. B H 4400 x 3500 X 2200 mm -Weight approx. 18500 kg -with: - CNC - control CYBELEC ModEva 15s BJ. 2007 -Back gauge with 4 controlled pneum. on the side and height-adjustable stop fingers -controlled bending AIDS in the velocity range -Hydr. -Pneum.. Clamp of the upper tool + substation witness -mot. Crowning / hydro cushion in the table -laterally movable support arms -E - foot switch -split pointed tool R 1-100 t / m, split die

Technical data: -Length approx. 2500 mm -Width approx. 1000 mm -Height approx. 800 mm -Top plate thickness approx. 90 mm - 4 pieces t grooves in the table surface length 2500 mm -Centre distance of the T-slot table surface each 215 mm -T - slot width approx. 40 / 70 mm -T - groove depth approx. 60 mm -Space requirement L 2700 x T 1200 x H 800 mm - weight approx. 3700 kg

Technical data: -Get well plate surface -Length approx. 2000 mm -Width approx. 1000 mm -Height approx. 1600 mm -Top plate thickness approx. 95 mm -Top plate with internal ribbing - 4 piece t grooves on the surface of the table length 2000 mm -Centre distance of the T-slot table top 230 mm each -Table side L 2000 mm with 12 holes M27 -T - slot width approx. 40 / 67 mm -T - groove depth approx. 35 / 60 mm -Space requirement L 2200 x T 1200 x H 1600 mm - weight approx. 4980 kg

Technical data: -maximum working width 750 mm -maximum material thickness approx. 1.0 mm -Beam + upper cheek fold away -Bending rail with cut-outs - space requirement approx. B 1000 x H 1100 x D 750 mm -Weight approx. 70 kg

M. No.: 6513/19

Plate bend Ingkant SM 52; cleaned and tested; Table equipment; suitable for Heidelberg SM 52 plates. Plate bender SM 52; good condition; cleaned and checked; table top model; used for Heidelberg SM 52 plates.

The HKB series swivel machines are used for bending thin sheet metal. Due to their compact design, they fit easily into small workshops and cover a wide range of applications with their segmented upper tool. With an adjustable angle stopper, these swivel machines are also suitable for the production of small batches. Compact and torsion-resistant Segmented upper tool for many bending options Integrated, manual bend compensation Adjustable angle stop for series production Hands free Foot control of the upper bolster clamp Workspace Working length 1270 mm Sheet thickness (max.) – 400 N/mm² 2 mm Dimensions (length x width x height) 1.6 m x 0.9 m x 1.18 m Weight 330 kg Angle range of the bending beam 135°

BLM DYNAM 3 CNC tube bending machine was built by BLM S.P.A. in Italy in 1999. Distinguished by its high productivity and bending accuracy, the machine is an indispensable tool in any production facility. The applied technical solutions and reliable components make it possible to perform fully automatic, serial bending of profiles and tubes with a maximum diameter of 60 mm. All process parameters are entered on an intuitive CNC controller with many functions that facilitate the programming of even the most complex shapes in just a few steps. Throughout its lifetime, the DYNAM 3 mandrel bending machine has been regularly serviced. The total weight of the machine is 5070 kg. Technical specifications of the BLM DYNAM 3 CNC tube and profile bending machine - CNC control system: BLM FNC 2000 R - maximum tube diameter: 60 mm - tool set for bending tubes Ø 25 mm - lubricant pump: FLENCO ...

A generally overhauled blower type GMb 039 is offered.

Printing plate bending for Heidelberg SM 52 Beil PB-S 52; good condition; cleaned and tested; Stand-up device; suitable for printing plates Heidelberg SM 52. Plate bender for Heidelberg SM 52 Beil PB-S 52; good condition; clened and checked; used for Heidelberg SM 52 plates.

Specifications: 2 castors hydraulically adjustable 3 rollers driven Resistance torque: 80 cm³ Shaft diameter: 100 mm Roll diameter: 315 mm lateral hydr. Controlled arm correctors left and right CE. Mark Bending capacity square: 120 x 60 x 5 mm Bending capacity flat steel: 130 x 25 mm Bending capacity tube: 114.3 x 6 mm Bending power angle: 100 x 10 mm Round steel: 80 mm Motor power: 11 kW Control panel with digital display Dimensions (length x width x height): approx. 1750 x 1850 x 1650 mm Weight: approx. 3.6 tons Accessories: Various bending rollers Condition: we will still carry out a complete service on the machine The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.

1 Qty. 1 Second-hand 3 roll bending machine Mfc.: SW GmbH Type: SRMV G Built: 1989 Strip width max.: 2000 mm Wall thickness: max. 25 mm / Ø 530 mm 2 Qty. 1 Second-hand 3 roll bending machine Mfc.: SW GmbH Type: SRMV Hy Built: 1981 Strip width: max. 3500 mm Wall thickness: max. 12 mm 3 Qty. Second-hand 3 roll bending machine Mfc.: SW GmbH Type: SRMV Hy Built: 1983 Strip width: max. 3500 mm Wall thickness: max. 19 mm 4 Qty. 1 Second-hand 4 roll bending machine Mfc.: SW GmbH Type: SVRM Built: 1981 Strip width: max. 2000 mm Wall thickness: max. 16 mm

Bearing number: 3488 Profile steel shears Manufacturer: Mubea, Type: KBLH 500 Machines NR.: 0156085927332, Year of construction: 0 Specifications: Size Printl 50 To Max punching dia 30 x 15 mm mm Stroke length 0-60 mm Number of strokes per min. 16 Extension 410 mm Flat steel 180 x 20 - 400 x 10 mm Angular steel 50 mm Round steel 55 mm Total power 7.5 kW Hydraulic. Length: 1400 mm, Height: 1800 mm, Width: 800 mm, Weight: 1800 kg

Technical data: - Bending capacity - steel pipe of 20 - 60 x 4 mm - - stainless steel pipe of 20 - 50 x 3 mm - max. resistance moment 6.2 cm - max bending angle 180° - max radius 125 mm - Bending speed 8 sec - Drive 400 V / 3 kW - Space requirement approx. L 2400 x H 1600 x D 1000 mm - Weight approx. 1400 kg - with: - Bending angle control via potentiometer with digital display - 6-fold bending angle preselection - Indoor + external pipe deburrer - Bending tools Rx2.5D x 38 ; • 50 , 65 ;

Qty. 1 Second-hand JCO pipe press bending line Mfc.: Samyul, ROBO, Shinsung, ChangSong, Rotech, FANUC, Hyupshun, Ingersoll Built: 2003, 2008, 2009, 2013, 2014 Plate material: Mild steel Plate dim.: 16.0 x 5.2 x 0.08 m – L x W x T Pipe dia.: Φ400~Φ1650 mm Pipe Length: 6.0m ~ 16.0 m Scope of supply: JCO Hydraulic Press Tack Welder Machine Sealing Welder Pipe Heating & Rotating Device Inside Welder Outside Welder Calibration Presses Milling Cutter Cutting Machine Bevelling Machine Compressor

M. No.: 121

MACRI ITALIA PROVAR 6-45 U-D tube and profile bending machine was built in 2015 in Italy by Macri Italia srl. The machine, designed for precision bending of tubes and profiles with a maximum diameter of 45 mm, is an answer to the daily challenges of modern business. The machining process is performed by means of a moving head with reinforced gears, which allows the bending of standard and variable radiuses in 6 axes (X,Y,Z,B1,B2,A). Each axis, in turn, is driven by brushless servomotors, which ensure the achievement of high dynamics, combined with excellent positioning accuracy. The machine’s extensive range of equipment includes e.g. state-of-the-art MACRI software with many useful functions and the ability to run a anti-collision test with 3D simulation. The PROVAR 6-45 U-D mandrel bending machine weighs 4000 kg. Technical specifications of the MACRI ITALIA PROVAR 6-45 U-D tube be ...

Robust, high-quality round sheet bending machine for already profiled workpieces (sheet blades) - with motor drive at the bottom and top adjustable workpiece width between 300 mm and 800 mm, largest sheet thicknesses which can be bent round copper / titanium zinc / aluminium 0.8 mm - galvanized steel sheet 0.7 mm - stainless steel sheet 0.5 mm, smallest possible bending radius 350 mm - bending radius depending on the yield strength - smallest bending radius galvanized steel plate 0.7 mm - 1,000 mm, continuous speed infinitely adjustable 1 to 6 m/min, drive capacity 2 x 0.75 kW, weight 375 kg

Technical data: - bending and rolling by hand, - max working width 1020 mm - max. material thickness St 40 1.25 mm - Bending angle adjustment via end stop 10 - 180 ° - max hub upper cheek approx. 85 mm - max. adjustable bending cheek 20 mm - Shaft diameter 55 mm - Upper shaft can be swivelled - Rear shaft parallel + obliquely adjustable - Space requirement approx. W 1500 x H 1400 x D 750 mm - Weight approx. 400 kg

Press brake edge machine edge bench press used Manufacturer: Mengele Type: C320-4B Built: 1966 last revision and repair: 2000 Location D-01587 Riesa Dimensions WxH: 6,250 x 3,650 mm Edge knife width: 6,150 mm sheet thickness at 6,000 mm bending length: approx. 7.5 mm. The machines are designed for very deep shaft bends, therefore very deep cheek recesses. Original 300 t pressing force - In 1989 the pressing force was increased to 350 t. The press is in very good condition despite its age. The machine is disassembled and ready for loading. documentation for the machine is available. Weight: about 45 t

Mechanic plate bending machine Goyar 3C-25/20. Bending lenght: 2000mm. Bending capacity: 25mm. Diameter of upper cylinder: 285mm. Diameter of lower cylinders: 235mm. Main motor power: 20cv. Bending speed: 5 mpm. Weight: 5500Kgs.

Key data: 200 mm, 400 , 360

Profile Bending machine Model AR360 -Year 2004 MG brand made in Italy OUTPUT SHAFTS 360 MM Capacity as per the original bending chart here enclosed Configuration installed with the machine -Pyramid dual pinch side rolls independent hydraulic positioning bending and pre-bending performance -The 3 shafts driven with hydraulic motor and gear unit individual on each roll -Synchronized speed automatic hydraulic control between the 3 rotating shafts -hydraulic traction tool to roll HEB_INP_UPN bending on hard-side. -Lateral correctors left/right hydraulic operated in 3 directions Tooling with the machine -Set of rollers for pipe: 6” and 12” -Set of rollers with adjustable opening width up to 400 mm ( for all the profiles bending easy way and hard way ) -Set of rings to increase the rollers opening width up to 500 mm ( for all the symmetric profiles b ...

Key data: 200 mm, 300 , 200

Profile bending roll used equipment hydraulic model AR200 year 2008 make MG Italy Capacity bending chart photo in enclosed -Technical data: Output shafts size 200 mm -Machine complete with set of rollers adjustable for the various shape of profiles. -Traction tool hydraulic operated for the HEB-beam - IPE - UNP bending the hard side. -Lateral correctors left and right side hydraulic operated in 3 direction. -Included additional set of rolls for pipe 6" inches -Machine with 3 rolls driven system with individual hydraulic motor and axial gear-unit on each shaft. -The 3 shafts working on bearings, heavy duty type with sealed lubrication. -Centralized control panel movable on wheels with all electric commands. -Dual rolling speed up to 5 mtr/min with automatic balancing system between the 3 rolls. -Safety devices in compliance with European regulation. CE mark. - ...

Max Bending Length 2250mm Machine is in excellent condition - As New LOW HOURS

Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic CNC – controlled double-sided pre-bending – conical bending device, three hydraulically driven rollers (one hydraulic motor per roll), hydraulic linear sub-roll adjustment – hard chrome-plated piston rods – hardened and ground rollers - PILZ® laser protection - BECKHOFF® CNC – control with Ethernet technology and large touch screen - DANFOSS® precision hydraulics – central lubrication system Maximum bending length 2,000 mm Roll diameter 170 mm Smallest weft diameter = 1.1 x the roll diameter The rollers run in bronze plain bearings. Nominal pre-bending performance over the entire bending length at 5 x D = 5 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 7 mm sheet steel/ST40 Drive power  ...

Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation - automatic CNC – controlled double-sided pre-bending - Conical bending device - three hydraulically driven rollers (one hydraulic motor per roller) - hydraulic linear under-roll adjustment - hard chrome-plated piston rods - hardened and ground rollers - PILZ® laser protection - BECKHOFF® CNC control with Ethernet technology and large touch screen - DANFOSS® precision hydraulics - Central lubrication system

GM-SB-38CNC-2A1S tube bending machine was built in 2019 in China by ZHANGJIAGANG KING-MACC MACHINERY MANUFACTURING CO., LTD. The machine, distinguished by its high precision and ease of operation, is used for bending tubes and profiles with a maximum diameter of 38 mm. All process parameters, including even the most complex shapes, are programmed in an intuitive PLC controller with memory for up to 200 work programmes. Thanks to the high degree of automation, the offered GM-SB-38CNC mandrel bending machine is an indispensable tool in any production facility. The total weight of the machine is approximately 1500 kg. Technical specifications of the GM-SB-38CNC-2A1S tube and profile bending machine - operator panel with PLC controller - bending capacity: ⌀ 38×2 mm - maximum bending angle: 180° - maximum bending radius: 200 mm - minimum bending radius: 20 mm - mandrel length: 32 ...

Very high-quality CNC – controlled precision sheet metal round bending machine with automatic bending sequence calculation – automatic CNC – controlled double-sided pre-bending – conical bending device, three hydraulically driven rollers (one hydraulic motor per roll), hydraulic linear sub-roll adjustment – hard chrome-plated piston rods – hardened and ground rollers - PILZ® laser protection - BECKHOFF® CNC – control with Ethernet technology and large touch screen - DANFOSS® precision hydraulics – central lubrication system Maximum bending length 2,000 mm Roll diameter 170 mm Smallest weft diameter = 1.1 x the roll diameter The rollers run in bronze plain bearings. Nominal pre-bending performance over the entire bending length at 5 x D = 5 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 7 mm sheet steel/ST40 Drive  ...

specifications: - Pressure capacity 100 KN / 10 t - Compressive force adjustable 0 - 100 kN - Stroke length 0 - 150 mm - Clear width approx. 200 mm - Lifting speed 0 - 0.6 m/min - Tool height up to approx. 100 mm - Bending performance - with prism MW 100 flat to approx. 100 x 12 mm - Tube bending up to approx. 1 inch - Directional power Wy at straightening block distance of 1m 100 cm³ - Drive 400 V / 1.1 kW - Space requirement approx. W 1100 x H 1000 x D 650 mm - Weight approx. 400 kg

VLB GROUP ECO 92 NC2 tube bending machine was built in 2022 in Portugal by the VLB Group. The machine has only undergone a test run and has not been used in production conditions. The machine is used for precision bending of tubes and profiles with a maximum diameter of 92 mm. All machining parameters are programmed in an advanced industrial controller with a touchscreen. It allows precise basic movements, i.e. bending angle (Y axis) and tube rotation (Z axis), to be performed fully electrically. The distance between bends (X axis) is, in turn, precisely set using mechanical stops. Thanks to the technical solutions used, the offered ECO 92 NC2 mandrel bending machine is the perfect choice for high-quality workpiece bending in small and medium series. The total weight of the machine is 2420 kg. Technical specifications of the VLB GROUP ECO 92 NC2 tube and profile bending machine -  ...

sheet width: 1500 mm plate thickness: 1,5 mm distance between columns: 1500 mm bending angle max.: 135 ° total power requirement: - kW weight of the machine ca.: 0,36 t dimensions of the machine ca.: 1,7 x 0,7 x 1,3 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

AMOB MAH 40/3 CNC 3-roll bending machine was built in 2021 in Portugal by AMOB Group. The machine, designed for bending tubes and profiles, ensures the highest precision and repeatability of the produced parts. The machining process is performed by three hardened rollers, of which the upper roller has hydraulic adjustment. Each of these is driven by a reliable, high-power motor, which is located inside a fully welded body. This solution enables bending of even the most complex shapes both vertically and horizontally. All this is complemented by an advanced CNC control with memory for numerous programmes. The MAH 40/3 CNC tube and profile bending machine weighs 540 kg. Technical specifications of the AMOB MAH 40/3 CNC bending machine - control panel with CNC control - number of rollers: 3 - roller diameter: 148 mm - roller rotational speed: 12 rpm - number of shafts: 2 - shaft di ...

tube diameter: . mm wall strength: . mm bending radius min.: . mm Control: total power requirement: kW weight of the machine ca.: . t dimensions of the machine ca.: . m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tube diameter: . mm wall strength: . mm bending radius min.: . mm Control: total power requirement: kW weight of the machine ca.: . t dimensions of the machine ca.: . m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 95 mm Shaft diameter: 30 mm Shaft revolutions: 7 U/min roll diameter: 132 mm Drive: 0,75 kW weight: 220 kg range L-W-H: 530x900x660 mm Equipment / Accessories: - Two driven rollers with grooved surface - Manual feed of the upper roller - working position horizontal and vertical (with tilting base) - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn different profiles are used e.g. Flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

2.The main structure and performance of the machine tool: This machine tool is designed and manufactured using the latest technology, ensuring its strength, rigidity, and safety. Its simple and elegant appearance and exquisite workmanship demonstrate meticulous machining and component assembly. The machine utilizes a single, high-quality welded steel structure, resulting in a thick, rigid frame. The machine surface is sprayed with imported rust-resistant primer and topcoat, ensuring it remains as good as new for a long time. The frame and upper working slide are machined using imported large-scale CNC floor-type boring and milling machines, ensuring the required positioning accuracy of all mounting surfaces. This machine tool primarily consists of a frame, upper slide, backgauge system, slide, synchronous control device, mold, hydraulic system, and control system. 2.1 Frame: This pa ...

The all-electric servo bending machine is one of the products with independent intellectual property rights developed by our company. Special high-load screw and guide rail structure, imported bearing installation, high load-bearing capacity, high positioning accuracy, long life, machine tool rigidity, precision retention, and reliability are close to perfection. By introducing advanced design concepts and scientific design methods, the shortcomings that traditional designs cannot avoid have been solved. This bending machine is fast and simple to program, can realize concurrent linkage of multiple axes, fast feed positioning, and significantly improves the efficiency, accuracy and consistency of bending, which is far superior to traditional hydraulic bending machines, and does not require the use of hydraulic oil, is environmentally friendly and pollution-free. Compared with traditional ...

round material: 40 mm tube diameter: 70x2 mm square material: 80x30x3 mm L-beam: 50 x 5 mm I - beam section - flat steel: 80 x 16 mm I-beam section - upend: 50 x 15 mm roll diameter: 157 mm Shaft diameter: 50 mm bending speed: 2,95 m/min total power requirement: 1,1 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: 1000x950x1450 mm Domestic equipments: - Special steel shafts (42CrMo4) hardened and ground - a set of standard rollers - lower rollers up and down hydraulically deliverable - digital display for lower rollers - separate control panel - in one direction manually adjustable lateral straightening rollers - manual lubrication - horizontal and vertical operation - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Two driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 80 mm roll diameter: 260 mm : 7 U/min : 170 mm : 27 kN : 160 mm : 450 mm total power requirement: 3,7 kW dimensions: 980x1430x1600 mm weight: 1380 kg Accessories / equipment: - Three driven rollers with a smooth surface - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can bend different profiles are used e.g. Flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: R10-R260 : 210 ° bending speed: 2 U/min : 1 1/4 x 3,5 mm : einphasig - 230 V drive motor: 1,1 kW : < 70 dB weight of the machine ca.: 80 kg dimensions of the machine ca.: 410 x 1000 x 570 mm Accessories / equipment: Hard copper and aluminum: 54x2 mm Steel tube: 42x3 mm Stainless steel: 42x2.5 mm Solid material: 30 mm Number of programs: 30 each 9 bends Control: Soft-touch control panel in 8 different languages Mobile by driving device The controller allows easy programming of the automatic cycle The controller is equipped with a system diagnostics and has a great language selection. Patented fast tool change system A single bending speed The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 48x3,5 mm : 48x2,5 mm : 32 mm : 64x2 mm bending speed: 2 U/min : R10-R300 total power requirement: 1,5 kW weight of the machine ca.: 110 kg dimensions of the machine ca.: 410x1000x570 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.