bend used for sale

plate thickness: 2,5 mm throat: 260 mm distance between roll centers: 92 mm weight: 295 kg range L-W-H: 1,2 x 0,7 x 1,2 mm Furnishing: - 3 sets of rollers - motor-driven beading machine - foot switch - Operating instructions in German - CE mark / declaration of conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2600 mm plate thickness: 10,0 mm pre-bending: 8,0 mm diameter of upper rolls: 230 mm side roll diameter: 190 mm diameter of lower rolls: 210 mm total power requirement: 7,5 kW weight of the machine ca.: 5.560 kg. range L-W-H: 4.650x1.380x1.300 mm Furnishing: - hydraulic 4 roll bending machine - Conical bending device - Induction hardened rollers - Digital display for the two side rollers - mobile control panel - 2 speeds - hydraulic folding bearing - Operating instructions in German - CE mark / declaration of conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table load: 150 kg weight of the machine ca.: 250 kg dimensions of the machine ca.: 800 x 700 x 950 mm Exhibit Machine Producer: BENDMAK Type: SRP 015 Load capacity: 150 kg Load center: 100 mm Eccentricity: 100 mm Rotation of the turntable: 360° Strongest inclination: 90° Input Power: 380 V Rotary motor: 0,18 kW tilt motor: 0,25 kW Speed: 1,4 m/min Slew: 30 sek. Table-Ø: 500 mm T-Slots: 5-72 Height in horizontal rotation: 700 mm Dimensions: Height: 950 mm Length: 800 mm Width: 700 mm Weight: ca. 250 kg Earthing: 300 Amp. Additional information: - adjustable speeds - control panel with 5 m cable - digital speed indicator on the control panel for monitoring the rotation - weld grounding mechanism - mechanical angle indicator - engine brake with air cooling The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 1,25 mm Shank diameter: 26 mm weight of the machine ca.: 50 kg Sheet thickness: 1.25 mm Roller shaft color: 62 mm Roller center distance: 250 mm Shaft-Ø: 26 Throat Depth: 260 mm Dimensions of the Machine: Length: 600 mm Height: 550 mm Width: 350 mm Weight: about 50 kg incl. standard rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

round bar steel: 45 mm square edge steel: 42 mm L-beam: 140 x 13 mm flat steel: 350 x 20 mm pressure: 550 kN throat: 305 mm notching: rectangle tool: mm total power requirement: 5,5 kW weight of the machine ca.: 1260 kg dimensions of the machine ca.: 1360 x 750 x 1565 mm 2 working cylinder with 2 separated electric foot switch for 2-people-handling New notching table, new knife for the rectangle notcher and new punching table included For further information please see brochure. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 6 mm pre-bending: 4 mm upper roll diameter: 210 mm lower roll diameter: 190 mm side roll diameter: 170 mm total power requirement: 7,5 kW Overall size: 5200x1400x1300 mm machine weight ab.: 5.400 kg Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2100 mm plate thickness: 6 mm pre-bending: 4 mm upper roll diameter: 160 mm lower roll diameter: 140 mm side roll diameter: 120 mm total power requirement: 2,2 kW Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 50 t : 150 x 16 mm stroke: 28 mm : 12 mm plate length: 250 mm square edge steel: 45 mm round bar steel: 50 mm sheet thickness: 13 mm total power requirement: 3,5 kW weight of the machine ca.: 2,5 t dimensions of the machine ca.: 1,8 x 1,0 x 1,6 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Bendmak APAS 360 hydraulic plate rolling machine Machine is in excellent condition Maximum thickness : 25 mm Top roll diameter : 350 mm

Bendmak APAS 360 4 rolls plate rolling machine Working length : 3100 mm Maximum thickness : 40 mm Machine is in excellent condition

Laser welding machine Automatic Letter Bender ALB SPEED MASTER 500W DUAL It is barely used, we have used it 4 times. We bought it for a project that ended up not working out. 500W Year 2020

sheet width: 3100 mm plate thickness: 6 mm pre-bending: 5 mm upper roll diameter: 170 mm min. bending diameter: Ø 255 mm bending speed: 4,5 m/min total power requirement: 4 kW weight of the machine ca.: 2300 kg dimensions of the machine ca.: 3800x1100x1130 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Max. punching diameter: 30mm, max. punching force: 500kN, throat depth: 610mm, stroke: 0-60mm, weight: 1.69t.

sheet width: 3100 mm plate thickness: 13,0 mm pre-bending: 10,0 mm diameter of upper rolls: 300 mm side roll diameter: 210 mm diameter of lower rolls: 270 mm total power requirement: 11,0 kW Furnishing: - hydraulic 4 roll bending machine - Conical bending device - Induction hardened rollers - Digital display for the two side rollers - mobile control panel - 2 speeds - hydraulic folding bearing - CE mark / declaration of conformity - Required instructions The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 4,0 mm throat: 260 mm distance between roll centers: 132 mm stroke: 55 Oberwalze mm tool adaptor: Ø 35 mm, 12 mm Nut mm total power requirement: 3,0 kW weight of the machine ca.: 450 kg. range L-W-H: 1,6 x 0,9 x 1,2 m Furnishing: - Hydraulic adjustment - 3 sets of rollers - Double seams, beads, flanging rollers - Double foot switch - Operating instructions in German - CE marking / declaration of conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 16 mm pre-bending: 13 mm upper roll diameter: 330 mm lower roll diameter: 300 mm side roll diameter: 240 mm total power requirement: 11 kW Overall size: 5600x1650x1900 mm weight of the machine ca.: 10.600 kg Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 900 mm table load: 1.000 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 1,1 UpM T-slots: 6 x M16 Tilt Angle: 90-180-105 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 930 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width - max.: 200 mm plate thickness: 6 mm flat steel: 70 x 7 mm round bar steel: 13 mm weight of the machine ca.: 50 kg dimensions of the machine ca.: 800 x 500 x 1800 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 1550 mm : 4,5 mm : 4,0 mm roll diameter: 140 / 210 mm : 2,2 kW : 1210 kg : 2650 x 900 x 1200 mm - 2 central rollers driven by an electric motor - Swing-out upper beam - Conical bending device - separate control panel - self-braking main motor - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized rear roller adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1050 mm plate thickness: 1,8 mm pre-bending: 1,5 upper roll diameter: 70 mm min. dia.: 105 mm total power requirement: 1,1 kW weight of the machine ca.: 320 kg dimensions of the machine ca.: 1700x700x1100 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Magnetic drilling machine, magnetic drilling machine Core hole drilling machine, Metal core hole drilling machine DR. BENDER Type EK 323 Masch No. 180543 Year of construction approx. 1988 Drilling capacity 23 mm Spindle holder MK 2 Spindle speed 160 / 400 / 1250 rpm. Magnet 215 x 105 mm Drilling unit 220 Volt, 50 Hz, 1025 Watt E-magnet 220 Volt, 50 Hz, 65 Watt - Spindle speed via 3 gear stages - Left and clockwise rotation - E-magnet KOCH, type KL32/6 - Drill head height adjustment guided in a linear guide - manual expulsor - Drill stand rotatable on magnetic base, clamping via toggle screw Dimensions L x W x H 680 x 380 x 630 mm Weight 35 kg good condition; used

I - beam section - flat steel: 80 x 16 (d 1200) mm I-beam section - upend: 50 x 15 (d 1000) mm L-beam: 50 x 5 (d 1200) mm round material: 40,0 (d 800) mm bar material dia. max.: 70 x 2,0 (d 1600 ) mm square material: 80x30x3 (d 4000) mm channels - flange: UNP 80 (d 800 ) mm bending speed: 4,4 m/min roll diam. toproll: 157 mm bore: 50,0 mm total power requirement: 1,1 kW weight: 485 kg Furnishing: - electro-hydraulic ring/profile bending machine - Hydraulic lower/side roller adjustment for extra small bending radii - Lower/side roller can be delivered individually - 3x powered rollers - divided roller segments - Digital position display of the bottom/side rollers Display with TouchScree function - hardened tool holder (42CrMo4) - Machine base - 2x manually adjustable side guides - Horizontal and vertical work possible - freely movable control panel - Pressure gauge / pressure indicator  ...

plate thickness: 1,25 mm throat: 250 mm distance between roll centers: 62,0 mm engine output: 0,7 kW weight: 170 kg range L-W-H: 0,7 x 0,6 x 1,3 mm Furnishing : - 4x pairs of beading and flanging rollers included - Robust beading machine with motor-driven rollers - Lower shaft with adjustable stop - for the economical production of various types of beads - high accuracy due to precision-bearing shafts - Clearly arranged switching elements - Underframe equipped with storage compartment - powerful drive motor, even under continuous load - Mobile foot switch for right and left rotation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 220 V frequency: 50 Hz combination machine: . extensive accessories: ca. 50 Sätze pressure: 50 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 2,5 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 92 mm tool adaptor: 35 mm speed: 3,5 m/min total power requirement: 1,5 kW weight of the machine ca.: 295 kg dimensions of the machine ca.: 1200x700x1200 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Clamping plate, scribing spotting plate, measuring plate, measuring table, welding table, welding table, straightening plate -Mounting plate: with measuring arm Bendix type 36A -Width: 1500 mm -Length: 3000 mm -Height: 230 mm -Plate thickness: 55 mm -Plate: with supporting ribs, without straightening -Adjustable feet: 5 pieces -Transport dimensions: 3160/1670/H800 mm -Weight: 2500 kg

Bendi forklift in lovely condition. Manufacturer rebuild in 2015. New charger 2015. 5.5m lift. Available immediately, viewing possible in Milton Keynes, UK.

: 1050 mm : 5,5 mm : 5,0 mm roll diameter: 130 / 195 mm : 2,2 kW : 1050 kg : 2150 x 900 x 1200 mm - 2 central rollers driven by an electric motor - Swing-out upper beam - Conical bending device - separate control panel - self-braking main motor - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized rear roller adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 2050 mm : 4,5 mm : 4,0 mm roll diameter: 140 / 210 mm : 1,1 kW : 1530 kg : 3220 x 1200 x 900 mm - 2 central rollers driven by an electric motor - Swing-out upper beam - Conical bending device - separate control panel - self-braking main motor - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized rear roller adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

A vacuum former from the US company The Channel Letter Bender. The machine was bought in 2017 and has operated over the years around 30 hours, so it is practically brand new and is well maintained. All the technical specifications are in the PDF. Shipping dimensions 1650 mm x 2400 mm x 2400 mm ( L x W x H ) ( 65 inch x 95 inch x 95 inch ) weight 700 kg ( 1543 lbs ) Operating area 3000 mm x 3500 mm ( 118 inch x 137 inch )

Bendmak CYL ST 190-30/5 3 roll plate rolling machine Working length : 3250 mm Maximum thickness : 5 mm Machine is in good working condition

Description: connected load: 400V max. coil width: 600mm mandrel diameter: 80mm weight approx.: 183 kg, Approx. Onsite Dimension. (l x w x h): 1,660 x 800 x 830 mm

workpiece thickness max.:80 mm workpiece thickness min.:5 mm plate size without being adjusted:2000x1000 mm size of plate min.:100x100 mm control:CNC Mubea Matic100 hole diameter:min/max:10/40 mm workpiece weight:750 kg deburring device max.:d=40 mm traversing speed:80 m/min work height max.:1050 mm positioning accuracy:+/- 0,5 mm opening of gripping pliers min/max.:Typ I: 5/45 mm opening of gripping pliers min/max.:Typ II: 45/85 mm feed length:max. 150 mm rapid traverse::8 m/min spindle turning speed range:112-180-224-280-355-560 U/min work table::L:2500;B:950 mm arm gripping device:4 Stück tool taper:Kegel DIN 6327 longitudinal travel:x=2800 mm cross travel:y=1000 mm bore spindle stroke:max. 150 mm total power requirement:25,0 kW weight of the machine ca.:5,5 t space requirements approx. LxWxH:5,0x5,5x2,7 m plate size with beeing adjusted also 1000x4000 mm possible with roller conveyo ...

Bending semi-automatic, tube bending machine, mandrel bending machine MOBITEC type BAH 1-2 KOTTMANN und BERGER GmbH Fabr. No. 056 Year of manufacture 09/2004 - for simultaneous bending of two steel pipe sections up to 12 mm bending angle max. 90 Tube diameter max 12mm Mandrel length approx. 65 mm Nominal power 3.5 kW Compressed air max. 6 bar / approx. 1 litre per bending cycle Mains connection 400 volts, 50 Hz - Pneumatic clamping - Pneumatic mandrel retraction - Control for angle input via STOBER Controlbox Series 4000/5000 - Control SIEMENS S7-200 with display TD200 - Machine without bending tools and without tool bearing bolt 25 x 183 mm - only 1 bending mandrel available (see pictures). Space requirements L x W x H 1000 x 1000 x 1500 mm Weight 390 kg good condition; used

Hand - Swivel bending machine KRAMER type AMS 650 x 1.5 Hand swivel bending machine, bending bench Year of construction approx. 1985 Working length 650 mm Sheet thickness at 40 kg/mm2 1.5 mm Upper cheek opening approx. 60 mm Bending cheek adjustment approx. 0-25 mm Bending angle 0-180- Upper cheek adjustment via hand crank - Pre-screw rail for the bending clamp - one-piece sharpening rail 135 Space requirement L x W x H 1200 x 600 x 1100 mm Weight 160 kg good condition; used

Swivel bending machine, cant bench, gutters, roof gutters, beading machine, beading machine, three-roller round, three-roller sheet metal bending machine, bending machine, sheet metal round bending machine, 3-roller round bending machine, profile bending machine, three-roller sheet metal rolling machine -Swivel bending machine: with 3-roller bending machine on a solid base -Max. Working width: 1020 mm -Max. Sheet thickness: 1.5 mm -Roller diameter: 2x 50 mm / 1x 53 mm -Dimensions: 1450/800/H1155 mm -Weight: 346 kg

Bending tool, die, upper knife, upper tool, straight tool, upper beam -Bending tool: for folding machine -Tool angle: 45° -Dimensions: see the drawing in the photos -Dimension: 47 x 11mm -Length: 945mm -Weight: 3.5 kg

Bending tool, matrix, upper knife, upper tool, upper beam -Bending tool: from Lotze HDZ swivel bending machine -Length 2678 mm -Hole spacing: 100mm M10 -Dimensions: see the drawing in the photos -Dimension: 2678/6/H45 mm -Total weight: 5,6 kg

Bending tool, matrix, upper knife, upper tool, upper beam -Bending tool: from Lotze HDZ swivel bending machine -Length 2678 mm -Hole spacing: 100 mm M10 -Dimensions: see the drawing in the photos -Dimension: 2678/15/H57 mm -Total weight: 15.7 kg

Bending tool, die, lower knife, lower tool, lower beam -Bending tool: from Lotze HDZK swivel bending machine -Widening: for lower cheek -Dimensions: 2487 x 100 x 15 mm / 190 x 100 x 15 mm -Hole spacing: 100 x 18 mm -Transport dimension: 2487/100/H30 mm -Total weight: 29.4 kg

Bending tool, die, upper knife, upper tool, straight tool, die tool, seam closing tool -Tool: for folding machine RAS Typ 74.30 -Dimensions: see the drawing in the photos -Distance recess rail: center center 650 mm -Dimension: 3060/28/H121 mm -Weight: 65kg

Upper tool - bending tool for die bending machine GEWA Press brake set: 15 pieces Type: GWP-1291 Angle: 88 Radius: 0.8 mm Segment height: 200 mm max. pressure per meter: 85 t/m Total length of the 15 segments: 4010 mm Segment lengths: 6 x 505 mm, 1 x 400 mm, 1 x 190 mm, 1 x 100 mm, 1 x 69 mm, 1 x 58 mm, 1 x 48 mm, 1 x 42 mm, 1 x 40 mm, 1 x 33 mm Total height with tool holder: 230 mm Tool holder: 30 x 13 mm, 8.4 mm groove Weight: 260 kg very good condition Suitable lower tool under stock number 60752. Tool set suitable for AMADA, TRUMPF and LVD press brakes with appropriate tool system; used

: neu : 12 - 14 Wochen ab Auftrag : Deutschland : 4010 mm : 2 mm : 1.5 mm : 4 ELECTROCINEMATIC DRIVE OF THE BENDING JOINTS millmeter precise adjustment of the clamping beam BMS MULTI-Touchcontrol electric powered rotary shear electronic depth stop flexible material supports inclined bending beam optimized geometry of the clamping beam safety equipment accoring to the control rules BG Germany 3 year warranty on stands and tension arms. Quality Made in Germany. FURTHER MODELS FROM3 UP TO12 M LENGTH AND FROM 1,25 MM UP TO 2,00 MM BENDING CAPACITY ON REQUEST. OPTIONS: Extended depth 1.250 mm price on request Conical depth stop to bend conical profiles and narrow/wide bendings for easy intermateing price on request clamping beam made out of hardox price on request Prices ex works Germany. Transport and commissioningat customers place on request. The data for this ad was created with Modul ...

: neu : 12 - 14 Wochen ab Auftrag : Deutschland : 8020 mm : 2 mm : 1.5 mm : 8 ELECTROCINEMATIC DRIVE OF THE BENDING JOINTS millmeter precise adjustment of the clamping beam BMS MULTI-Touchcontrol electric powered rotary shear electronic depth stop flexible material supports inclined bending beam optimized geometry of the clamping beam safety equipment accoring to the control rules BG Germany 3 year warranty on stands and tension arms. Quality Made in Germany. FURTHER MODELS FROM3 UP TO12 M LENGTH AND FROM 1,25 MM UP TO 2,00 MM BENDING CAPACITY ON REQUEST. OPTIONS: Extended depth 1.250 mm price on request Conical depth stop to bend conical profiles and narrow/wide bendings for easy intermateing price on request clamping beam made out of hardox price on request Prices ex works Germany. Transport and commissioningat customers place on request. The data for this ad was created with Modul ...

: neu : 12 - 14 Wochen ab Auftrag : Deutschland : 6400 mm : 2 mm : 1.5 mm : 6 ELECTROCINEMATIC DRIVE OF THE BENDING JOINTS millmeter precise adjustment of the clamping beam BMS MULTI-Touchcontrol electric powered rotary shear electronic depth stop flexible material supports inclined bending beam optimized geometry of the clamping beam safety equipment accoring to the control rules BG Germany 3 year warranty on stands and tension arms. Quality Made in Germany. FURTHER MODELS FROM3 UP TO12 M LENGTH AND FROM 1,25 MM UP TO 2,00 MM BENDING CAPACITY ON REQUEST. OPTIONS: Extended depth 1.250 mm price on request Conical depth stop to bend conical profiles and narrow/wide bendings for easy intermateing price on request clamping beam made out of hardox price on request Prices ex works Germany. Transport and commissioningat customers place on request. The data for this ad was created with Modul ...

Bending machine FAVRIN 3100×30 PHLS CNC (A3708) Type: hydraulic Max worklength: 3100 mm Eletric motor (power) 75 HP Courant needed 380V Weight 32 ton Machine was previously used to bend Hardox workpieces. bending capacities examples: – 3100 x 25 mm > multi stage bending for large radiuses – 2500 x 30 mm > multi stage bending for large radiuses – 3100 x 17 mm > single stage bending – 2500 x 25 mm > single stage bending full CNC corner + backgauge control upper hydraulic clamping of tools clamping force: 220 ton max bending angle: 110° max open: 500 mm Tooling included for radius bending Also 2 new extra cilinders included

This ERMAKSAN POWER BEND PRO 3100-175 Bending machines machine was manufactured in 2018 in Turkey. The machine has a Cybelec cybtouch 12 PS 2D control panel with touch screen. It is equiped with a high-quality hydraulics HOERBIGER and a hydraulic cylinders are made of high-strength hardened steel and chrome plated, which guarantees their durability and longevity.