129,071 used machines on RESALE, but how to find them? Machine Search
Diameter of bending rollers 550 mm Drive Type Hydraulic Main motor power30 kW
sheet width: - mm plate thickness: - mm distance between columns: - mm total power requirement: - kW weight of the machine ca.: - t dimensions of the machine ca.: - m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Equipment: 1 pliers feed right 4 Carriage Units Working Range: Wire thickness range: 0.5 - 2.0 mm Band width: up to 10.0 mm Length of move; up to 100 mm Output: up to 300 rpm
Equipment: 1 Carriage Feed Right 1 eccentric press 250 kN 4 normal carriage units 1 narrow carriage unit Working Range: Wire thickness range: up to 6.0 mm Strip width: up to 80 mm Feed length: up to 250 mm Power: 10 - 250 rpm
Transnorm belt curve conveyor left GKF 90°-700-500-IR450 - NEW RA2313 Technical data: Frame width (NB): 700 mm Frame width with Bearing cover and motor: 900 mm belt width (GuB): 500 mm height (BH): 220 mm height with motor (MH): 350 mm Inner radius (IR): 450 mm Conveying angle: 90° degrees Conveying speed (v m/s): 0,67m/s Drive: SEW motor motor Electrical data: 50Hz V380-500, kW 0,55 / S1 Year of construction: 2020 Optionally available: Supports Frequency converter for stepples speed controll Prices net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, Gattingerstreet 11 B & C, 97076 Würzburg Features: Construction year: 2020 condition: new Nominal / inner radius in mm: 450 Nominal / outside width in mm: 700 Belt width in mm: 500 angle: 90° Driven: YES Running direction: LINKS Engine type: SEW Eurodrive KW: 0,55/S1 Conveyor speed m / s: 0,67 scope of delivery: without suppor ...
Equipment: 1 piece BIHLER noise protection cabin 1 piece pliers feed right 1 piece eccentric press 70 kN 4 Norma sled units 1 piece narrow sled unit Working Range: Wire thickness range: 0.5 - 3.5 mm Strap width: up to 32 mm Feed length: up to 170 mm Power: up to 250 rpm
Stock number: 4017 PROFILE BENDING MACHINE Manufacturer: Roundo , Type: R4 Machines NO.: 1735, Year of manufacture: 1977 Specifications: Angle steel 90x9 mm Flat steel 200 x 30 mm Frame steel upright 100 x 18 mm Round steel 60 mm Load by steel 40 Kg/mm2 30 cm3 Upper roller 275 mm Ø Shaft dia. 105 mm Square steel 55 x 55 mm T-steel 90x10 mm Total power 5.5 kW Length: 1500 mm, Height: 1400 mm, Width: 1400 mm, Weight: 2500 kg
Press brake Manufacturer: AMADA PROMECAM Type: HFB 125/40 Year of Make: 1991 Control: DELEM DA 58 Press force max:. 1,250 kg Stroke max.: 180 mm Sheet thickness 8 mm Working width/passage: 3.7 m Number of phases: 3 Power consumption: 11 kw Voltage/Frequency: 380/50 Rated current: 24 Weight: 9,900 kg Availability: immediately Reference Number: L2131
Material width 150 mm, material thickness 0.5 -3.0 mm Colour: green Total power requirement: 380 V Weight: 350 kg Dimensions: 800 x 1200 x 1350 mm Roller diameter: 24 mm Machine number 700257
A semi-automatic NC tube bending machine Tracto-Technik is available. Tube diameter: 48mm, max. tube length: 3000mm, max. material thickness: 4mm, max. bending angle: 180°, max. bending radius: 125mm, bending accuracy: +/-0.2°, bending speed: 20°/s. Machine dimensions X/Y/Z: approx. 3900mm/800mm/1250mm, weight: approx. 700kg, control system: Siemens Simatic. Documentation available. On-site inspection is possible.
Key data: 3000 mm, 8 mm
3-roll bending machine / round roller Schäfer SRMVHY – fully functional For sale is a used 3-roll bending machine (round roller / sheet metal bending machine) from the manufacturer Schäfer, model SRMVHY, built in 1992. The machine is in fully functional condition and is ready for immediate use. The rollers are hydraulically adjustable, which allows for precise and comfortable adjustment. The round bending machine is ideal for bending sheet metal in workshops and production plants. Technical data: Manufacturer: Schäfer Model No.: SRMVHY Year of Make: 1992 Max. sheet width: 3,000 mm Max. sheet thickness (mild steel): 8 mm Roller diameter: approx. 200 mm Voltage: 380 V Dimensions (L x W x H): approx. 5,300 x 1,800 x 1,300 mm Condition: used, fully functional Equipment: hydraulically adjustable rollers Changes and errors in the technical data, ...
Fasti 2040 x 5 mm Number of rolls: 3 rolls Roll capacity cold: 2040 x 5 mm Roll dia upside: 160 mm Power needed: 7,5 HP Length: 3250 mm Depth: 900 mm Hight: 1300 mm Weight: 3100 kg
Type: 108 Number of rolls: 3 rolls Roll capacity cold: 2540 x 2,5 mm Roll dia upside: 140 mm Dia under roll - side rolls: 140 mm Power needed: 5 kW Weight: 1760 kg
De plaatdikte is afhankelijk van het profiel. dop: 0,5 gt; 1,5 mm 7 stations vermogen: 2,4 kW gewicht: 430 kg
A CNC flat wire vertical wire bending machine V&C GmbH is available. Wire thickness range: 0.8mm-10mm, max. wire width: 30mm, min. winding inner diameter: 20mm, max. winding outer diameter: 250mm, max. winding height: 160mm, max. winding height with holding rod: 500mm, max. winding length: 250mm, min. bending radius: R6°, max. number of edges: 12/revolution. Machine dimensions X/Y/Z: approx. 2650mm/1000mm/1800mm, weight: approx. 800kg. Documentation available. On-site inspection is possible.
This MACRI PROVAR 6-45 U-D was manufactured in 2022. It features a maximum steel bending capacity of à 45x4 mm and stainless steel up to à 40x3 mm. With a bending angle of up to 190° and speeds reaching 450 mm/sec on the X axis, this roll bending machine ensures precision and efficiency. Consider the opportunity to buy this MACRI PROVAR 6-45 U-D roll bending machine. Contact us for more information about this machine.
This AMADA Vipros 255 was manufactured in 2001. It is a used punching and bending machine, ideal for those looking to enhance their metal fabrication capabilities. Contact us for more information about this machine.
This Sahinler HKP-Z 100 was manufactured in 2016. A robust C-frame PLC controlled deep drawing press, it features a pressure force of 1000 kN and a stroke of 500 mm. The machine includes a large table size of 900x600 mm and a throat depth of 300 mm, suitable for diverse punching and bending tasks. Consider the opportunity to buy this Sahinler HKP-Z 100 punching and bending machine. Contact us for more information about this machine.
This 3-axis Finn-Power Shear Genius TRS 6 SBU was manufactured in 1996, featuring a punching force of 300 kN and a sheet working range of 2500 mm à 1250 mm. It supports up to 21 tool stations and can handle sheet thicknesses up to 6 mm. Automatic tool change system enhances productivity. Consider the opportunity to buy this Finn-Power Shear Genius TRS 6 SBU punching and bending machine. Contact us for more information.
Offer 26008 Technical data: - 3 mot. driven rollers with asymmetrically hydr. Feeding of the two lower rollers - bends e.g. flat bars 100x40 flat up to Ø 600 mm - bends e.g. flat bars 100x20 upright up to Ø 800 mm - bends e.g. U 180x70 up to Ø 800 mm - Shaft diameter per 100 mm - Useful length of the standard shafts approx. 250 mm - Shaft rotation 5.4 rpm - Roller diameter 315 mm - Drive 400 V / 11 kW - With: - Separate control panel with digital actual value displays - Lateral straightening rollers manually adjustable - Standard bending kit for flat and angle material - Weight approx. 3500 kg - Space requirement approx. W 1600 x H 1700 x D 1600 mm
BPR BA 35 Asymmetrical CNC tube and profile bending machine with 3 driven rolls Factory REMANUFACTURED, RETROFITTED and UPGRADED in 2020. AS-NEW CONDITION MACHINE ! Contact: info@roce.hr / roce.strojevi@gmail.com Reason for Sale: Very low operating hours. Stored for years as a properly packed backup machine. In 2020, it was sent to the original manufacturer for full factory refurbishment and modernization (although fully functional at the time). After refurbishment, it was again kept in storage as a reserve unit. Now sold only because it is no longer needed as backup capacity. Excellent condition. Ready for immediate use. Description: This CNC-controlled profile bending machine is designed for complex bending operations with continuous radius variation. It allows choice between automatic and manual operating cycles, providing flexibility for different produc ...
Amada HFE 80-25 Year: 11/ 1999 Working length: 2550 mm Stand width: 2125 mm Pressing force: 80 tons CNC control: AMADA OPERATOR II graphic Controlled axes: Y1/Y2; X1/X2; R1/R2; Z1/Z2 mot. adjustable back gauge Stroke: 200 mm Projection: 420 mm Crowning Working height: 960 mm Engine power: 9 kW CE mark Dimensions (length x width x height): approx. 3000 x 2250 x 2250 mm Weight: approx. 6 tons
Offer 26046 Technical data: - 2 mot. Driven rollers - Manual. Lining of the upper roller - Shaft diameter 30 mm - Shaft rotation 6 rpm - Roller diameter 88 - 108 mm - Bending capacity approx. - Flat steel 50 x 8 mm - Square 20 mm - Round tube 42 mm - Drive 380 V / 0.55 kW - with: - Right / left – run - Tube roller set approx. 16 mm - Weight approx. 150 kg - Space requirement approx. W 650 x H 1300 x D 950 mm
Used, technically overhauled reinforcing steel bending machine. 4 pieces of counter retaining strips. 2 footswitches with emergency stop function. Max. bending power 2 rods 28mm D. Bending speed 6/13 revolution.min. Control Siemens Touch Display CC Power 4 KW.
Key data: 3500 mm, 12 mm
Schäfer SVRM 3500/12 - CNC 4-roll bending machine - Siemens CNC control with joystick for roller positioning and digital display (renewed in 2006) - Hydraulic tilting of the upper roller by control panel - Rollers made of quenched and tempered material with a strength of 900 N/mm² - Year of construction 1989 Technical data - Max. sheet width: 3500 mm - Bale length of rollers: 3550 mm - Max. sheet thickness bending: 12 mm - Max. sheet thickness bending 4xS/3xS: 8 / 6 mm - Max. insertion limit of the sheets at 20% work hardening: 380 N/mm² - Upper and lower roller diameter: 360 mm - Side roller diameter: 290 mm - Smallest radius to be achieved: 220 mm - Feed speed lower roller: 200 mm/min - Feed speed side rollers: 700 mm/min - Total installed capacity: 22 kW - electr. Control: 380 V / 50 Hz / 3 Ph - Machine weight: 21100 kg
Used, technically overhauled reinforcing steel bending machine. 4 pieces of counter retaining strips. 2 footswitches with emergency stop function. Max. bending capacity 1 rods 28mm D. Bending speed 6/16 revolution.min. Control with bending pins for three angles adjustable by hand. Power 3.5 KW.
Key data: 1020 mm, 1 mm
3-roll round bending machine, with wire inserts, seam groove, Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length: 1020 mm Sheet thickness max. steel: 1.25 mm Colour: green Weight: 220 kg Dimensions: 1290 x 600 x 1050 mm Number of round rollers: 3 pieces Roller diameter: 55 mm Machine number 1685
Offer 26018 Technical data: - Max. working length 500 mm - Max. sheet thickness 1.5 mm - Various roller diameters - Drive – brake motor 400 V / 1.4 kW - Space requirement approx. W 850 x D 1700 x H 1250 mm - Weight approx. 0.8 t - Roller attachments 42 ; 45 ; 50 ; 55 ; 60 ; 65 ; 70 ; 90 ; 135 mm
Tube bending machine Tubend TB 42 hydraulic new machine - Capacity: 42 × 3 mm - Hydraulic drive - Adjustable stroke - Emergency stop function - Includes 3 tool sets: 33.7 mm, 26.9 mm, 21.3 mm - Documentation available - Connection: 400 V
Module was changed because a PCSS conversion took place on the machine and therefore this module no longer fits. Fully functional.
This ERCOLINA Megabender TOP 030 die bending machine was manufactured in 2011. It features a maximum pipe diameter of 2 (60.3 mm) and a pipe slide length of 3,000 mm. With 30 programs and the capability to work with various materials, consider the opportunity to buy this ERCOLINA Megabender TOP 030 die bending machine. Contact us for further details.
PCSS for conversion of the machine from PCSS-F to PCSS-A. Small restriction: When the machine was started up after a long standstill, the reference run had to be repeated several times. After a successful homing run, the part works without any problems.
Key data: 50 t, 2550 mm
Hydraulic press brake Manufacturer Fasti Type UBGP 50/25 max pressing pressure 50t max working width 2550mm Lifting height 150mm with block matrix and div segments Press is in a used 100% functional condition. Can be loaded with overhead crane.
STIERLI - Bender 300 U / Horizontal bending machine -Year of construction 2011 -CE marking -Max. working pressure 300KN -Stroke length 300mm -Motor power 4 KW -Hand switch -Footswitch -Various matrices -Bending tools -Stop -Documentation Dimensions: LxWxH 1.5x1.2x1.3 meters / Weight 800Kg
Fasti - Round bending machine / type 2040x2mm -GS / Identifier -Roller diameter 105mm -Max. sheet thickness over the entire length 2mm -Footswitch -Safety device Dimensions: LxWxH 3x1x1.3 meters / Weight 1400Kg Hebjvdnahskn Au S Tsl
An asymmetrical three-roll plate bending machine MG is available. Working width: 2000mm, roller diameter: 130mm, max. plate thickness: 3mm, power: 6kW, weight: approx. 2000kg. An on-site inspection is possible.
A four-roll plate bending machine Kramer is available. Working width: 2000mm, max. plate thickness: 3mm, power: 3kW. An on-site inspection is possible.
Press capacity approx.: 360 kN Bending length approx.: 1020 mm Distance between side frames: 932 mm Effective open height: 295 mm Throat depth: 150 mm Working speed: 25 mm / sec feeding speed: 220 mm / sec Control: TASC 6000 Working hours machine: 41422 h working time jacking beam: 4713 h Length: 1805 mm Width: 1330 mm Height: 2380 mm Weight of machine approx.: 2600 mm
Roll bending machine manufactured in 2020. This Metallkraft GBP BASIC 26100 features a pressing force of 100 tons and a maximum bending length of 2600 mm. It is equipped with an 11 kW engine and has an oil tank capacity of 150 liters. If you are looking to get high-quality bending capabilities, consider the Metallkraft GBP BASIC 26100 machine we have for sale. Contact us for further details.
sheet width: 3355 mm plate thickness: 63,5 mm roll diameter: 686 mm voltage: 400 V total power requirement: 150 HP weight of the machine ca.: 95 t dimensions of the machine ca.: 62 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Roller bending machine Dimensions: LxWxH 0.9x0.6x1.1 meters / Weight 250Kg
CONTROLS CNC controls SIEMENS TECHNICAL SPECIFICATION Max. diameter of tube: 120 mm Max. bending radius: 180 mm ELECTRICAL SPECIFICATIONS mains voltage: 400 V mains frequency: 50 Hz DIMENSIONS / WEIGHTS space requirements -left/right-: 8000 mm space requirements -front/back-: 2600 mm total height: 2300 mm total weight approx.: 16500 kg machine in a very good condition Machine in very good condition Special features: - Free-form bending option - Laser scanner for securing the bending area - Foot pedal for safe start - Bending simulation Automation: - CNC control BEND MOTION CONTROL - Automatic mandrel lubrication as MMS Retrofit 2018: - Control system retrofit - Cables replaced - Bending head overhauled - Guides replaced - complete equipment (see photos) (Ø22x2, Ø28x2, Ø38x2.6, Ø42.4x2.6, Ø48.3x2.6, Ø60.3x2.9, Ø76.1x3.2, Ø88.9x3.2, Ø114.3x3.6 ...
RASI S80.6L - Tube bending machine Curve and mandrel bending of tubes and round profiles Coils of pipes incl. tools and documents Year of construction 2006 Technical data - Tube Ø x wall thickness: 82 x 2.6 mm - Max. resistance torque: 12.7 cm³ - Min. tube Ø: 4 mm - Outer bending radius: 228 mm - Inner bending radius: 34 mm - Min. bending radius: 1.5 x D - Max. bending angle (accuracy ± 0.1°): 195° - Bending speed return (programmable): 0 - 9.3 rpm - Bending speed advance (programmable): 0 - 6.6 rpm - Counter holder rail: rigid / running - Tooling: 1-, 2- or 3-groove - Bending direction: right - Feed speed (infinitely variable): 0 - 60 m/min - Push-back force of the feed: infinitely adjustable during bending - Twisting speed (infinitely variable): 0 - 60 rpm - Max. twist angle (± 0.1°): unlimited - Max. pipe clamping force: 8 t - Diameter bridging of a ...
Manufacturer: Durma Model: HRB-4 2010 Year of Manufacture: 2012 Type of Machine : 4-roll bending machine Machine Weight: 4,450 kg Condition: Unused - acquired May 2023, never operated, stored in warehouse Technical Specifications: - Bending Length: 2,050 mm - Max. Bending Thickness (mild steel): 8 mm - Max. Bending Capacity: 10 mm - Top Roller Diameter: 210 mm - Lower Roller Diameter: 190 mm - Side Roller Diameter: 180 mm - Min. Rolling Diameter: 30 mm - Motor Power: 11 kW - Oil Tank Capacity: 160 litres - Machine Dimensions (L x W x H): 3,830 x 1,160 x 1,180 mm Find more here - / Contact us at -
Max. pressing force: 800 kN (80t) Max. bending length: 2500 mm At the moment there are 5 punching brackets that can be moved (built-in tool with 4 x 12 mm hole diameter and 1 x 10 mm) No other bending prisms available
sheet width: 1000 mm plate thickness: 3,0 mm distance between columns: 1050 mm diameter of upper rolls: 90 mm total power requirement: 1,1 KW weight of the machine ca.: 0,47 t dimensions of the machine ca.: 1,7 x 0,8 x 1,35 mm Sheet metal bending machine with custom dimensions: - Capacity 1050 x 3.0 mm - Digital display - Hardened rollers - Conical bending - Swiveling top roller - Brake motor - Safety device: Emergency stop cord - Documentation in English - 400V The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Limpet coil roller machine hydraulic To form half round pipe from flat metal strip and bending into wanted radius with spiral continuous. Manufacture MG srl Year 2002 -Shafts output 80 mm -Interchangeable set of molds to form half pipe 60 mm , 90 mm , 115 mm -Coil holder for the reel metal strip with guide-way bench uncoiling and alignment the steel strip to the rolling machine -Pinching lower central roll adjustable to form the half pipe -Digital position readout to determine the bending diameter of the bending, the pitch of the spiral, the shape of the half tube forming -hydraulic arm movable in 3 directions to set the pitch for continuous coil rolling -Upper vertical support hydraulic operated to hold in position the formed diameter and collect the spiral from diameter 700 to diameter 3000 mm -Operator console electric with push buttons and digital posi ...
maximum number of results exceeded
please refine your search
