We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
119,260 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
Bed milling machine Manufacturer Nicolas Correa Year of construction 2003 Control Heidenhain TNC 426 Clamping surface 2000 x 700mm table load 3.500kg Travel X/Y/Z 2000/800/800mm Tool holder SK50 max speed 4,000 rpm Machine weight 9.000kg Machine is in a used good condition
used
Roller trestles roll bed Manufacturer: PEMA / ESAB Type: 3 TXA / 3 TXN (1 unit) Year of construction: 2008 Load/section max.: 1.5 tons / 1.5 tons Maximum force F: 3 kN Rolling speed range: 60 – 1200 mm/min. Fixed center height: 434 – 800 mm Total diameter range min-max.: 106 – 2179 mm Steel rolls piece/section: 2 pieces Roller diameter / total width: Ø 350 / 80 mm Mains voltage: 230 V – 1 Ph – 50 Hz/16 A Length: 1690 mm / 1445 mm Width: 670 mm / 570 mm Height: 615 – 878 mm / 610 – 878 mm Weight: 480 kg / 420 kg Remote Control / Cable Length: RC31H / 6m
used
MTE BF-2700 CNC Bed Milling Machine 3+2 manual head 3000 rpm Control Unit : Heidenhain TNC 530i The only problem is that the spindle gear is worn and it makes noise over 2000 rpm. Seller uses it by 1500 rpm without any problems. Maintenance has been done
used
CME FCM 9000 Bed milling machine 5-axis Table size 9500 x 1200 mm. Travel X-axis 9000 mm. Y-axis 1500 mm. Z-axis 1500 mm. Maximum table load 5000 kg/ Mtr. Vertical milling head can be swivelled by 1°x1° CNC control Heidenhain TNC 430 CB If you have any questions about the machine, as well as a scheduling for viewing, please contact us by phone or e-mail.
used
Used Rambaudi Rammatic 600 cnc bed type milling machine
used
CNC Universal Bed Type Milling Machine Condition very good –11000 operating hours only Inspect under power IS POSSIBLLE Manufacturer Soraluce Model TA-A 25 Year 2018 Control Heidenhain TNC 640 Table size 2700 x 1000 mm Table load max. 6700 kg T-Slots 6 x 22 H12 Reference slot 1 x 22 H8 Distance between T-Slots 140 mm Travels Longitudinal travel X 2500 mm Vertical travel Z 1250 mm Cross travel Y 1200 mm Through the two horizontal positions forward of the automatically swiveling milling head the vertical machining can be extended by 500 mm (up to 1750 mm). Feed thrust X/Y/Z 10000 N Rapids X/Y/Z 25000 mm/min. Average Acceleration 2 m/s2 Automatic indexing milling head Number of swivelling positions 0.001° x 0.001° Positions in ...
used
MORI SEIKI DuraTurn 2550 MC Machine with CNC milling bed DuraTurn 2550 MC 2010
used
5-Axis CNC Bed Type Milling Machine LAGUN mod. GBM 22E Manufacturer: Lagun Model: GBM 22E YOM: 2000 Control: Fagor 8055 Table surface: 2200x1040 mm Distance from Table Center to Column: 1217 mm No. of T-slots and width: 7 - 22mm Groove distance: 140 mm Maximum weight on the table: 7000 kg X- Axis travel: 2000 mm Y- Axis travel:: 1000 mm Z- Axis travel: 1000 mm C- Axis travel: +/- 180° A- Axis travel: +/- 180° Spindle Cone: ISO 50 Main engine power: 22/27.5 kW Speed variation continue: 50 ÷ 3000 rpm Fast forward: 10000 mm/min Weight of the machine: 15000 kg
used
Milltronics MB25-A CNC Bed Type Milling Machine Machine is in quite good condition Slides are in very good condition X : 650 mm Y : 1150 mm Z : 650 mm Computer system has been fully reset All electronic system has been overhauled.
Table length: 5000 mm Table width: 1050 mm Longitudinal X: 4500 mm Cross Y: 1250 mm Vertical Z: 2000 mm Positions ATC: 46 CNC Brand: _Unknown / Other CNC Model: ITNC -A4 CNC Milling head 2.5 x 2.5 Gr -ATC Chain toolchanger 46 positions -Extended lower bed for more work load on table -Table 5000 x 1050 mm X-Axis: 4500mm Y-Axis: 1250mm Z-Axis: 2000mm Table load: 13000 Power on spindle: 30kW Spindle speeds: 4000Rpm Millinghead auto-index:2.5 x 2.5 (A4 milling head)° Length: 12000mm Width: 6300mm Height: ...
used
Table length: 2600 mm Table width: 1000 mm Longitudinal X: 1000 mm Cross Y: 2500 mm Vertical Z: 1000 mm Positions ATC: 1 CNC Brand: Heidenhain Bed type milling machineLagun Goratu - FBF 2600 Head has been replaced Central luibrication Doors in front off machine Coollant system HeidenHain TNC 426 HeidenHain HR-410 Handwheel X-Axis: 2500mm Y-Axis: 1000mm Z-Axis: 1000mm Table Length: 2600mm Table Width: 800mm Table load: 6200 Power on spindle:22kW Spindle speeds: 2100Rpm Spindle Taper: Bt-50ISO/Bt/Mk Feed rate X-Axis:8000mm/min. Feed rate Y-Axis:8000mm/min. Feed rate Z-Axis:8000mm/min. Length: 5000mm Width: 3600mm Height: ...
used
Table length: 3000 mm Table width: 1000 mm Longitudinal X: 2705 mm Cross Y: 1209 mm Vertical Z: 1004 mm Positions ATC: 0 CNC Brand: Heidenhain Bed type milling machine ZAYER - 20 KF 3000 Automatic head 2 x 180 Gr Central lubrication Heidenhain TNC 426 Heidenhain HR-410 Handwheel X-Axis: 2705mm Y-Axis: 1209mm Z-Axis: 1004mm Table Length: 3000mm Table Width: 1000mm Table load: 10000 Power on spindle: 22kW Spindle speeds: 3000Rpm Spindle Taper: 50ISO/Bt/Mk Feed rate X-Axis: 15000mm/min. Feed rate Y-Axis:&nb ...
used
Table length: 3200 mm Table width: 1100 mm Longitudinal X: 3000 mm Cross Y: 1100 mm Vertical Z: 1500 mm Positions ATC: 30 CNC Brand: Heidenhain Bed type milling machineSachman - BS 110 MACH-ID 7645 Make: Sachman Type: BS 110 Control: HeidenHain TNC 426 Year: 1998 COSMO 4000 automatic head over CNC 2.5 Gr ATC Chain tool changer 30 positions With head Rotate Z Axis 1900 mm ( normal 1500 mm) HeidenHain HR-410 Handwheel Under power inspection possible any time ! X-Axis: 3000mm Y-Axis: 1100mm Z-Axis: 1500mm Table Length: 3200mm Table Width: 1100mm Table load: 10000 Power on spindle: &nb ...
used
Complete system with all the accessories necessary for installation and operation, see below! x = 7000 y = 1600 z = 800 / transverse stroke w = 600mm General overhaul 2007, year of production 1991 New Siemens Sinumerik 840D control system, new drive motors, guide guides refurbished, new control cabinets. Travel speed 12000 mm / min / w axis 6000 mm Rotary table TDV 2 max. workpiece weight 6t / clamping surface 1000x1000 Rotary table TDV 3 max. workpiece weight 12t / clamping surface 1250x1600 Accessories: 2 such as new angle crank / chain tool change system / plate field / complete housing / Knoll hopper feed / suction / coolant system with belt filter incl. all BWF fixators for the installation of machine bed and plate
used
Bed type milling machine SHW UF 6, new in 1977, control system Siemens
used
Key data: 2000 , 1000 , 1200
Used bed milling machine, Fab.Fpt, type LEM 934, built in 1996, Table 2500 x920 mm, longitudinal stroke 2000 mm, transverse stroke 1000 mm, vertical stroke 1200 mm, Control Heidenhain TNC 426. Machine has a defect in the Y-axis.
used
Field roller, grassland roller, meadow roller, soil roller, roller -for hill bed: adjustable increase -Diameter: 750 mm -Working width: 2000 mm -Equipment: Can be filled with water
used
Stock number: 3845 CNC BED MILLING MACHINE Manufacturer: CME , Type: MB-3000 FLEX Reconditioned spindle Year of construction: 2006 Specifications: Spindle speeds 2200 rpm Boring Spindle dia. 150 mm
used
Tip distance approx. 400 mm Tip height above bed 130 mm 12 speeds from 125 – 2800 rpm Space requirements, length x width 1.2 x 0.6 m Weight estimated approx. 400 kg
used
Specifications: Maximum turning length 90 mm Circulation diameter over bed 220 mm Circulation diameter over support 110 mm Center width 160 mm Bore 23 mm 3 speeds 350 / 700 / 1400 rpm
used
Tip distance approx. 500 mm Tip height above bed 125 mm 16 speeds from 120 – 1800 rpm Space requirements, length x width 1.2 x 0.6 m Weight estimated approx. 450 kg
used
Bed type milling machine ZAYER 30 KF-5000 Table 5000 x 1000 mm. Max allowed weight on the table 10 Tn. Travels: X 4710 mm. Y 1508 mm. Z 2013 mm. Spindle Taper ISO 50 Spindle speed 35-3000 r.p.m. Spindle power 37 Kw Feedrate 6-5000 mm/min Rapid traverse 15,000 mm / min Machine weight 32,000 kgs. Year 2000 Equipped with: CNC HEIDENHAIN TNC 426 Autoindexing milling head 360.000 pos (0.001º). The 2 bodies rotate at the same time. Cooling equipment Chip conveyor
used
Used fixed bed milling machine Brand: LAGUN Model: FBF 1200 Year: 1991 Weight: 5.500kg Control: HEIDENHAIN TNC 355 (New screen) Measures table: 1200x550mm Offsets axes: X - 1100mm Y - 600mm Z - 600mm Ferret head with hydraulic lashing tool. Cone: ISO 50 Spindle speeds: 50 - 3000 rpm (2 speed ranges) Advances in the X and Z axes: 1 - 3000 mm / min Fast forward X and Z axes: 10,000 mm / min Motor power: 15KW
used
Technical features of the second-hand MTE BF-4200 bed type milling machine Table dimensions: 4200x1000 mm Number of T-slots: 7 T slots measures: 22 mm Max weight on table: 13.000 kgs X-axis traverse: 4000 mm Y-axis traverse: 1200 mm Z-axis traverse: 1500 mm Milling head model: Automatic Spindle taper: 50 DIN 2080 Speed range: 3 ranges Speed: 40-3000 rpm Main motor power: 22 kw Year: 2004 Equipped with: Control: HEIDENHAIN iTNC 530 Electronic handwheel: HR-410 Tool magazine: Yes Internal coolant supply: 20 bar - with paper filter Chip conveyor: Yes
used
Bed Milling Machine - Universal Make Lagun Type FBF 3250 Year of construction 1989 x-travel 3000 mm y-travel 940 mm z-travel 1000 mm Table clamping area 3250 x 800 mm Spindle mount SK 50 Spindle speeds 40 - 1800 rpm Feeds - longitudinal/transverse/vertical 0 - 2250 mm/min Rapid traverse 6 m/min Table load 4500 kg Control HEIDENHAIN, TNC 355 Machine weight approx. 10.3 t Machine dimensions L x W x H 4.50 x 2.69 x 2.71 m Accessories Vertical head swiveling in 2 levels with hydr. Tool clamp, coolant device
used
NOVAR ACTIVE 4000 CNC milling machine built in 2002 in Italy is the perfect choice for even the most intensive production challenges. The machine allows for efficient machining of large-sized workpieces with a maximum weight of 10 tonnes with reliable components in the form of cutting tools and a high-speed spindle. The installed HEIDENHAIN TNC 426M CNC control additionally guarantees seamless operation of the machine and utilisation of its full potential and capabilities. The NOVAR ACTIVE CNC bed milling machine has been continuously serviced and has new bearings on the spindle. The total weight of the machine is 27000 kg. Technical parameters of the NOVAR ACTIVE 4000 milling machine - CNC control: HEIDENHAIN TNC 426M - feeds in the X/Y/Z axis: 3500/1100/1400 mm - rapid traverse in the X/Y/Z axis: 8000/10000/10000 mm/min - work table surface (L x W): 4000 x 1000 mm - maximum wor ...
used
Description: Serial number: FBZ-8882 Operating voltage: 380 V Frequency: 50 Hz Rated current: 60 A Connection: 40 kW Control: HEIDENHAIN TNC 407 Tool holder: SK 50 Travel distances: X: 2500 mm Y: 800 mm Z: 815 mm Table clamping surface: 2900 x 800 mm Distance from floor to top edge of table: 950 mm Table surface with 5 T-sLot width/spacing: 22H12/150 mm Center groove: 22H7 SPECIAL FEATURE: max. table load without weight limit! Distance spindle nose - table surface min./max.: 0 - 817 mm Distance spindle center - table start: 235 mm Distance spindle center - table end: 935 mm Universal head position: 90° Distance spindle center - table surface: min. 200 mm, max. 1100 mm Horizontal position: 0° Distance spindle center/table surface min./max.: 0 - 900 mm Distance spindle nose/start of table: 150 mm Distance spindle nose/table end: 820 mm Horizontal position: 180° Distance spindle center/t ...
used
Novar KBA 1700 – Year 1990 CNC Bed milling machine Loading in container can be arranged. X Axis 1500 mm Y Axis 700 mm Z Axis 800 mm CNC type Tnc 360 Max. spindle speed 2700 rpm Table length 1700 mm Table width 700 mm Max load on table 3000 kg Spindle taper Iso40 Spindle motor power 10 kW Overhauled no Novar KBA 1700 Weight 9000 kg
used
Description: Universal bed milling machine - Huron head manual - automatic Tool clamping - Handwheel - Central lubrication - Machine light - Table enclosure - Footswitch - Documentation x-travel 1600 mm y-travel 710 mm z-travel 710 mm Heidenhain TNC control Speed range - main spindle 12 - 1600 min/-1 Tool holder SK50 Table clamping area 2200 x 550 mm max. table load 3000 kg Number of T-slots 5 T-slots - width 20 mm T-slots - distance 9 mm Rapid traverse x/y/z 5 / 5 / 2.5 mm/min Machine weight approx. 9 t Space requirement approx. 3.5 x 2.80 x 2.75 m Approx. Onsite Dimension. (l x w x h): 3,500 x 2,800 x 2,750 mm, weight approx.: 9,000 kg
used
x-travel:2000 mm y-travel:800 mm z-travel:800 mm table-size:2.000 x 700 mm workpiece weight:3500 kg drive capacity - spindle motor:17 kW spindle cone:50 ISO spindle turning speed range:3000 U/min dimensions of the machine ca.:5265 x 3250 x 2730 m weight of the machine ca.:9 t CNC controller:HEIDENHAIN TNC-426 :manuell used universal bed type milling machine with chip conveyor, automatic 2 position (vertical/horizontal) head 3000Rpm The retrofitting jobs done in this machine, are the same than those done to all of our machines. - Completely repair of the head, replacing bearings, shafts and engaging gears. - Completely replacement of all the bearings of the machine. - Replacing the joining screws of the bodies. - Completely repair of spindles. - Adjustment and repair of axis. - Grinding and adjusting all guides, because of deterioration. - Grinding and adjusting of the guide ways of the ...
used
x-travel:2500 mm y-travel:800 mm z-travel:800 mm table-size:2.500 x 700 mm workpiece weight:4000 kg drive capacity - spindle motor:22 kW spindle cone:50 ISO spindle turning speed range:20 - 3000 U/min dimensions of the machine ca.: 7800 x 3315 x 2730 m weight of the machine ca.:11 t CNC controller: Heidenhain TNC 426 :Auto-indexing UDG (2.5º) :HR-410 used universal bed type milling machine with chip conveyor, automatic 2 position (vertical/horizontal) head 3000Rpm The retrofitting jobs done in this machine, are the same than those done to all of our machines. - Completely repair of the head, replacing bearings, shafts and engaging gears. - Completely replacement of all the bearings of the machine. - Replacing the joining screws of the bodies. - Completely repair of spindles. - Adjustment and repair of axis. - Grinding and adjusting all guides, because of deterioration. - Grinding and ...
new
turning diameter:300 mm turning length:320 mm control:Fanuc 0i TD MG max. swing diameter:520 mm spindle speeds:4800 1/min. spindle passage:44 mm spindle drive:7,5/9 kW brand new CNC slant bed lathe with 1. Control system Fanuc Oi-TD (8,4" LCD monitor) 2. X/Z-axis stroke 170/600 mm 3. X/Z-axis rapid traverse 30/30 M/MIN 4. Spindle motor 11 / 15 Kw 5. Spindle speed 4500 rpm (Belt driven type) 6. Spindle bearing dia. Ø 100 mm 7. Bar capacity Ø dia 51 mm) 8. Hydraulic Hollow chuck 8" x 3 jaws 9. Hyd. unit for chuck with air cooler 10. Servo driven turret system 12 stations 11. Manual tailstock stroke 500 mm + quill stroke 100 mm 12. Electrical cabinet with heat exchanger 13. Standard splash guide 14. Coolant unit 15. Transformer (power source 380V) 16. Chip conveyor H=1100 MM with trolley (chain type) 17. Machine color Tongtai white/Dark grey 18. Safety foot switch 19. Tricolor lamp 20. ...
new
turning diameter:520 mm turning length:500 mm control:Fanuc Oi-TF max. swing diameter:520 mm spindle speeds:4500 1/min. spindle drive:11 / 15 kW brand new CNC slant bed lathe with Contains: 1. Control system Fanuc Oi-TF (8,4" LCD monitor) 2. X/Z-axis stroke 170/400 mm 3. X/Z-axis rapid traverse 30/30 M/MIN 4. Spindle motor 11 / 15 KW 5. Spindle speed 4500 rpm (Belt driven type) 6. Spindle bearing dia. 100 mm 7. Bar capacity dia 51 mm) 8. Hydraulic Hollow chuck 8" x 3 jaws 9. Hyd. unit for chuck with air cooler 10. Servo driven turret system 12 stations 11. Manual tailstock stroke 275 mm + quill stroke 100 mm 12. Electrical cabinet with heat exchanger 13. Standard splash guard 14. Coolant unit 15. Transformer (power source 380V) 16. Chip conveyor H=1100 MM with trolley (chain type) 17. Machine color Tongtai white/Dark grey 18. Safety foot switch 19. Tricolor lamp 20. Fanuc warranty (wes ...
new
:SS-27 | SS-31 | SS-35 turning diameter:700|790|890 mm turning length:700/1200/1700/2200/3200/4200/5200 mm control:Siemens 828D spindle nose:A2-11/A2-15/A2-20/A2-28/A2-32 spindle bore:153/230/255/318/360/410/535/610 mm spindle speeds:20-1200/16-700/13-600/14-450/12-400/10-350/8-300/4-220 1/min speed steps work spindle:4-stufig (automatisch schaltend) cross feed:0,001~250 mm/min feed in z-axis:0,001~400 mm/min rapid travel - longitudinal/face:8/10 m/min dia of ball screw:45 mm in X-Achse / 60 mm in Z-Achse tool turret:10- oder 12-fach tool taper:VDI 40/50 oder Schaftaufnahme tool holder -shaft diameter:32x32 mm diameter tailstock quill:160 mm :200 mm tailstock quill taper MT:5 spindle drive:30/37 (37/45 opt.) kW servo motor X-axis:3,8 kw servo motor Z-axis:3,8 kw weight of the machine ca.:11t für Spitzenweite 700mm (weitere 500mm: 1,5t) t CNC controller:Siemens/Fanuc/Fagor steady rests:m ...
new
:SA-35 | SA-40 | SA-45 turning diameter:890|1020|1145 mm turning length:700/1200/1700/2200/3200/4200/5200 mm control:Siemens 828D spindle nose:A2-11/A2-15/A2-20/A2-28/A2-32 spindle bore:153/230/255/318/360/410/535/610 mm spindle speeds:20-1200/16-700/13-600/14-450/12-400/10-350/8-300/4-220 1/min rapid travel - longitudinal/face:8/10 m/min cross feed:0,001~250 mm/min. feed in z-axis:0,001~400 mm/min dia of ball screw:50 mm in X-Achse / 80 mm in Z-Achse tool turret:10-/12-fach tool taper:VDI 40/50 oder Schaft tool holder -shaft diameter:32x32 mm diameter tailstock quill:235 mm :200 mm tailstock quill taper MT:6 spindle drive:37/45 (50/60 opt.) kW servo motor X-axis:4,5 (6 opt.) servo motor Z-axis:4,5 (6 opt.) kw weight of the machine ca.:16,5t für Spitzenweite 700mm (weitere 500mm: 2,2t) t CNC controller:Siemens/Fanuc/Fagor steady rests:manuell und hydraulisch Solid slant bed esures the ...
new
x-travel:1500 mm y-travel:650 mm z-travel:500 mm table-size:500x2200 mm spindle drive:11 kW max. table load:1200 kg T-slot (width-distance-quantity):20mm x 100mm x 4 spindle taper ISO:50 spindle speed:6-300 1/min, 30-1500 1/min / 2 stufig universal head:360° (manuell schwenkbar) distance spindle center to table:vertikale Spindel: 6? 650 mm distance spindle center to table:horiz. Spindel: 8-660 mm feeds:2.5-3000 /2.5-2500 mm/min rapid speed:6000 / 6000 / 3000 mm/min power of feed servo motor :18/23/18 Nm Overall size:3220 x 2420 x 2800 mm Weight approx.:7300 kg ISO50 end milling tool shank Dia. 27mm:27mm, 1 Stück hand wheels:elektrisch, für alle Achsen screws cover:wegklappbar Features of bed type milling machine ? Servo motors drive for X, Y, Z three axes ? Handwheel can be equipped for easy tool setting and smoothly axis moving ? Robust & rugged machine body made of high grade casti ...
used
x-travel:2000 mm y-travel:1000 mm z-travel:1050 mm table clamping surface::2.400 x 1.000 mm control:HEIDENHAIN TNC 426 CB turning speeds:20 - 5000 1/min tool taper:SK 50 spindle:22 kW total power requirement:50 kVA weight of the machine ca.:10 t dimensions of the machine ca.:5 x 3 x 3 m CNC universal bed milling machine, direct measuring system, coolant device, cover chip conveyer head is swivelling automaticaly horizontal / vertical head is swivelling semiautomaticaly 2,5 degrees over inching head is swivelling manually on the 5 th axis with display on screen approx. 59.250 h hours "machine on", approx. 9.656 h hours "programm on"
used
turning diameter:810/680 mm turning length:2.500 mm centre distance:3.040 mm swing diameter over bed slide:530 mm spindle bore:145 mm turning speed range:10 - 2.000 1/min spindle drive:76 / 63 kW turret (x-stations):12 Pos. tool taper:VDI 60 Torque:1150 / 4005 Nm rapid travel range:X12 / Z12 m/min max. workpiece weight between centers:4.000 kg max. workpiece weight -without tailstock:630 kg total power requirement:140 kVA weight of the machine ca.:17,6 t dimensions of the machine ca.:7,7 x 2,85 x 2,7 m CNC-lathe with tailstock - live tools 12 / 8 kW (85 / 105Nm), - spindle 2,5° indexing, - steady 50 -200mm, - hydr. 3-jaw-chuck, - chipconveyor, coolant device, - tailstock, tailstock quill: - MT 5, - dia. 160mm, - stroke 285mm,
used
Type: 100 FSG, built: 1986, gas operated granulating rig, spray granulator with two media nozzle, separator, heat exchanger (Manufacturer: Ohl), blowback filter K 6 R (2,4 m²), dosing unit for adding seeds. Mint condition.
used
The New. ų l ū the tables for tests. Electric ą 's benefit: 230 V. Pressure (j) ė ga adjustable from 2 up to 10 bar. The speed ~ 44 PCs./min the event is governed by the product of the Į ilg į. A simple room. ė table at the time of the test (s) shall be identified. ym ė-ą character can be changed. The Manufacturer JSC MS Import, Lithuania. Video į ra as: abc://abc.youtube.com/watch?v=AqElqGkB7_c&feature=youtu.be
new
To separate and sort after the specific weight from light and heavy fraction. Useable for grain, aluminium/plastic, rubber/textile, cable-recycling, etc. Type and size are choiceable, depending on the product and throughput. At constant machine length, it is possible to choose between working width from: 450mm, 600mm, 900mm.
used
Table size: 500 x 1200 mm traverse path x: 1000 mm stroke y: 550 mm traverse path z: 600 mm spindle retainer: ISO 40 spindle speeds: 60-2700 rpm spindle drive: 10 kW Electr. Supply: 380 V, 20 kVA kW space: 3200 x 2800 x 2650 mm weight: 7.3 t
used
Spare parts support: No. 4379: 1 gebr. Post assemblies to serial. RAMBAUDI, Rammatic 1201, type b. with HEIDENHAIN iTNC 530 Accessories: 1. milling head SK 50 / 22 kw / 3,600 - 40 min-1 2. clamping table with T-slots and grid plate 3500 x 1000 3. 30-fach tool magazine CANI 4. chip conveyor - INDASS. Type TPF, 5 Control Panel iTNC 530 - BJ. 2010 6 electronic Handwheel 7 measuring system / glass scale HEIDENHAIN LS 706 C / ML 2840 mm 8 measuring system / glass scale HEIDENHAIN LS 706 C / ML 1140 mm 9 measuring system / glass scale HEIDENHAIN LS 706 C / ML 1440 mm 10 Panel with various assemblies 11 feed / servo - motor SIEMENS
used
SHW UFZ 5 S with tool robot for 60 tools. X 4000, Y 1100, Z 1100, spindle 6000 rpm, round table Dm 1250, pitch 360000, also with horizontal dividing head with steady, pitch 3600000, internal cooling 16bar. Very few operating hours. Condition: excellent (used)
Key data: 1600 Heidenhain, 1000 TNC 426, 1400
Table length: 1600 mm Table width: 1000 mm Longitudinal X: 1400 mm Cross Y: 1000 mm Vertical Z: 1000 mm Positions ATC: 0 CNC Brand: Heidenhain CNC Model: TNC 426 Make: CME Type: FS-1 Control: HeidenHain TNC 426 YOP: 2002 X-Axis: 1.400mm Y-Axis: 1.000mm Z-Axis: 1.000mm Table Length: 1.600mm Table Width: 850mm Table load: 2.500Kg Power on spindle:22kW Spindle speeds: 4000Rpm Spindle Taper: 50ISO/Bt/Mk Feed rate X-Axis:20.000mm/min. Feed rate Y-Axis:20.000mm/min. Feed rate Z-Axis:20.000mm/min. Length: 4.260 mm Width: 2.500 mm Height: 2.600 mm Weight: 9.900 kg Swi ...
used
Description CNC tool milling machine from lid suitable for tooling, fixture construction, training as well as mold making Travel: 1200x600x500mm Speed: 20-6300 rpm Technical data Control CNC Dialog 11 Table 1500 x 675 mm Longitudinal path (X,Y,Z axis) 1200x600x500mm Tool changer no Tool holder: SK 40 Vertical spindle speeds: 20-6300rpm Feeds 2-5000mm/min Connection 50 Hz 3x 380V Spindle motor 7.5KW Machine weight approx. 8200kg Dimensions 3300x2400x2400mm
new
oven 1150 inner chamber dimensions 1 x 1 x 2m t max 1150 Celsius PLC Öfen Verzinkungsofen Ve rgüteofen Anlassofen Industrieöfen Glühofen Ovens laboratory ovens industrial furnaces industrial furnace plants Industrial Furnaces high-temperature chamber furnaces hardening furnace anlageHärteöfen Annealing furnaces Conveyor belt Abg aswäscher Abkühlungsöfen Abwärmerückgewinnung Aluminiumgiessereimaschinen Anlassofen Brennöfen Dentalofen Durchlauföfen Emaillierofen Fusingöfen Generatives Fertigungsverfahren Anlaßöfen mit Luftumwälzung Anwärmöfen Aluminium – Glühöfen Abschreckbäder Beschickungsanlagen für sbguss Druckgußmasch inen Drehherdöfen Doppelkammeröfen Draht – Glühöfen Durchlauföfen Elev atoröfen Glühöfen für verschiedene Einsatzarten Gas Nitrieröfen Härteöfen Härtebäder Herdöfen Hubbalkenöfen Herwagenöfen Haubenöfen Indust ...
used
Traveling column milling machine SHW UniForce SHW Uniforce 6 (7-Achs) Traverse X / Y / Z Clamping area 10,000 / 3100/1600 mm 11,600 mm x 3,000 mm CNC attachment rotary table 2,500 mm x 2,500 mm maximum load 30,000 kg Control system: Heidenhain i TNC 530
used
Table length: 1600 mm Table width: 550 mm Longitudinal X: 1100 mm Cross Y: 700 mm Vertical Z: 500 mm Positions ATC: 0 CNC Brand: Heidenhain CNC Model: TNC 310 CME - FC 1100 Universal milling machine 1100 x 700 x 500 mm MACH - ID 6332 Make: CME Type: FC 1100 Control: Heidenhain TNC 310 YOP: 1998 X-Axis 1.100 mm Y-Axis 700 mm Z-Axis 500 mm Table Length 1.600 mm Table Width 550 mm Table load 300 kg Power on spindle 7.5 kW Spindle speeds 1800 Rpm Spindle Taper 40 ISO/Bt/Mk Dimensions Length 3.800 mm Width 2.800 mm Height&nb ...
used
Table length: 6000 mm Table width: 1000 mm Longitudinal X: 4300 mm Cross Y: 1200 mm Vertical Z: 1500 mm Positions ATC: 0 CNC Brand: Heidenhain CNC Model: TNC 426 MACH - ID 6109 Make: Nicolas Correa Type :L30-43 Control :HeidenHain TNC 426 YOP :1997 X-Axis 4.300 mm Y-Axis 1.200 mm Z-Axis 1.500 mm Table Length 6.000 mm Table Width 1.000 mm Table load 10,000 kg Power on spindle 25 kW Spindle speeds 3000 Rpm Spindle Taper 50 ISO/Bt/Mk Feed rate X-Axis 15,000 mm Feed rate Y-Axis 15,000 mm Feed rate Z ...