bed type mill used for sale

SCHARMANN HEAVYCUT 2 WFT 150 CNC Floor type Boring Mill Year 1978 Spindle Diameter: 5.9" (150mm) Milling Spindle Diameter: 11.02 (280mm) Spindle Taper: CAT 50 Ram Cross Section: 11.81" x 11.81" (300x300mm) Vertical Head Travel, Y-Axis: 137.79" (3500mm) Column Travel, X-Axis: 712.59" (18000mm) Quill Travel, Z-Axis: 23.43 (595mm) Ram Travel, W-Axis: 27.6" (700mm) Z & W Axis, Combined: 51.03" (1296mm) Spindle Speeds: 5.5-1000 RPM Spindle Feed Range: 0.003-240 IPM Rapid Traverse: 396 IPM Spindle Motor: 70 HP/ 105 HP EQUIPPED WITH: Heidenhain TNC 407 CNC Controls Ram and Spindle Travel Sliding Way Covers On X-Axis Bed Right Angle Head With 1 Degree Manual Indexing Hardened Ways Re-pained recently

Universal tool milling machine DECKEL FP 1 with 3 axis active digital display Heidenhain TNC 113 Year of construction: 1987 Travel: X 300 Y 160 Z 340 Speed range: 40 – 2000 rpm With the following accessories: Universal table 600 mm x 250 mm clamping surface Movable vertical milling head Extendable drill quill Infinitely variable feed via potentiometer 1 machine vice 1 counter holder with counter bearing 1 pc. milling mandrel long 0 22 mm Various tool holders S 22 x 2 Bellows Z Axis Machine light Automatic central lubrication pump Chip collection plate Coolant system Operating instructions THE MACHINE IS IN VERY GOOD CONDITION

Qty. 1 Second-hand Duplex board paper mill Mfc.: Hasegawa, Yodogawa, Fuyo Japan, Valmet, Finland, Kumsun, Chung Korea Buil: 1984 Width: 3400 mm Speed: 330 m/min. Productivity: 450 ton/day max. 350 ton/day (average) GSM: Max.500 g/m2 -The number of HEAD BOX: 7 sets -Fourdriner type -Dryer: 77 ea (Air type+Electric type)

BALLISTRINE- linear profiler,/shaper-double sided 10 hp cutter head per side- follows your templates - shapes both sides- 9' table- hydraulic feed- material hold downs- $7,800

Stock number: U2293-2 Used carbon steel grinding/refining mill by Pallmann (Germany) model PR8. Mill has bolted rotor with diameter 795 mm and stator with diameter 800 mm. Belt driven by el. motor 100 kW, 1480 rpm, 380 V, 50 hz. Manual adjustment of gap between milling plates. Mill has mounted 5 nozzles for feeding gas or liquid inside the milling chamber. Front door bolted with central feeding inlet through feeding chute. Bottom discharge.

U5 Lab Package For Pilot & Development Construction: 305 stainless steel with 316L stainless steel product contact parts. Surface Finish: Product contact surfaces mirror polished (Ra 0.10 micron), non-contact surfaces 150 grit (Ra 1.06 micron); welds cleaned and polished and all material contact welds ground flush and polished. Infeed Opening: 3.25" (83 mm) diameter with grid bars to prevent operator access to the rotating impeller. Infeed Chute: Hand-fed funnel, 6.4" diameter x 5" high (163 mm x 127 mm) with magnetic actuated safety interlock. Spindle Assembly: Sanitary pharmaceutical duty with pre-lubricated, sealed bearings, viton O-ring, two shaft seals, and double varilip seal in a stainless casing. Also suitable for use with vacuum. Impeller Speed: Approximately 1000 - 6500 RPM. Capacities: Varies based on tooling, feed and speed used. Discharge: 6" (152mm) tri-clamp di ...

x-280 ,y- 200 , Z 315 , Table dimensions 380x380/250x500 A lot of writings,much more than pictured

EXTRON L610 CNC vertical machining center was built in 2008 in Taiwan. Distinguished by its extensive machining capabilities, high precision and reliable components, the machine is ideal for every production facility, even during the most intensive and demanding challenges. The high-quality design with sliding doors additionally efficiently dampens any vibrations and ensures maximum process stability. The EXTRON L 610 milling center machines workpieces on a large T-slot table using reliable tools placed in a 20-position head and a powerful spindle rotating at a maximum speed of 8000 rpm. All process parameters are programmed in the intuitive FANUC Series 0i-MC CNC control with many useful features that minimise the operator’s need to operate the machine. The EXTRON machining center weighs 5750 kg. Technical data of the EXTRON L610 CNC milling machine - CNC controller: FANUC Seri ...

ID2430 Waagner Biro Wet Ball Mill 260 x 550 cm year/Year of construction 1987 52 t Wet ball mill, overflow ball mill, drum diameter 2600 mm, grinding track length 5500 mm, ground material: limestone 0-10 (16 mm), wet grinding process, 2-stage cyclone circuit, nominal grinding capacity: 12-22 t/h, filling weight max./normal: 44/39 t, installed engine power: 450 KW, rubber Skega armor Wet ball mill, overflow ball mill, drum diameter 2600 mm, grinding track length 5500 mm, regrind: limestone 0-10 (16 mm), wet grinding process, 2-stage cyclone circuit, nominal grinding capacity: 12-22 t/h, filling weight max./normal: 44/39 t, installed engine power: 450 KW, armouring rubber skega

Several BÜHLER MDDK roller mills in different versions on sale. Any sort of feeding With or without inlet glass Scraper knifes, single or divided spout Plain rolls or corrugated rolls Size 1000 mm or 800 mm with roller diameter 250 mm Our specialists will provide a liable solution with used Buhler MDDK roller mills at good value.

HELMA- model CF-40-copy milling/shaping machine feed thru with work piece return (2) milling spindles- 18" max. distance between the spindles centers- 28" x45" Table - (2) 30mm. work spindles- 10,500 RPM spindles- 4"max. cutting height - vertical adjustment 10 mm.- (2) 7 1/2 hp. spindle motors - 1/2hp. variable speed feed motor 5' to 30' per min.- 2,200 lbs. $7,500

Hammer mill Fa. Wery

Complete mill / mill plant with a capacity for the production of 100 tons of flour/24h consists of: Grain cleaning systems, bucket elevators, conveying augers, stainless steel pipe systems, etc. The automated mill has been continuously modernized and expanded. 1 Airtronic roller mill, made by Bühler 1 top-mounted filter, made by Bühler 1 Dust cleaners 1 double screening machine, Fbrikat Bühler 3 MJZF, make Bühler dissolver, total 7 metal silos for grain Conveyor systems and stainless steel pipe systems 1 Compressor systems Laboratory equipment consisting of: 1 glue washer 2 Perten Inframatic 8600 1 case counting device 1 gluten index device 1 Schlagkreuzmühle To the flour store: Storage cells 6x 7.5 tons Storage cells 2x a 25to 1x 15to -------------------- Elevators: 3x A 75to  ...

BALLISTRINE- C 70 N- auto feed thru (2) sided shaper(2) 10HP; 3PH spindle motors • (2) 30mm diameter spindles with 5in. under the nut • Spring loaded floating spindles • In-feed and out-feed rubber covered upper feed rollers • Working width 14.4in. (360mm) max • Working height 4.8in. (120mm) max • Min working length 9.6in. (240mm) • Spindle 8,000 RPM • feed 3 to28..Price-$8,900

Table size: 254 x 1100 mm Table movement x: machine. u. v. hand 682 mm Table movement y: hand 380 mm Table movement z: hand 457 mm Milling head swiveling to: +/-90 or +/-45 ° Spindle retainer: ISO 40 Spindle speeds: 70-2300 rpm Quill feeds: 0.038 â 0.152 mm / min Spindle drive: 380 V, 2.2 kW Space: 1600 x 1600 x 2150 mm Weight: 1420 kg

5 Qty. 1 Continuous 6 Stand Cold Rolling Mill Mfc.: Fröhling Built: 1984 Type: 4-Hi Strip width: 220 mm Thickness: 0.15 – 2 mm 8 Qty. 1 Strip welding machine (Cold mill) Mfc.: A.I. Welders Built: 1986 Rev. in 2002 Speed: 75 – 600 m/min. Width: 233 mm Thickness: 0.175 – 2.0 mm 9 Qty. 1 Induction Treatment Furnace (Cold mill) Mfc.: Otto Junker Built: 1986 Width: 220 mm Thickness: 0.175-2.0 mm Speed: 8-60 m/min. Temp.: 550 °C 10 Qty.1 Quenching unit (Cold mill) Mfc.: Otto Jumker Built: 1986 Flow: 95 m³/h Temperature: 29 °C Size: 1.2 x 1.2 x 2.8 m 11 Qty. 1 Rotary shear (Cold mill) Mfc.: HDE Built: 1996 Strip width: 220 mm Thickness: 0.1 – 0.95 mm

Table surface: 300 x 1300 mm Table movement x: 950 mm Table movement y: 220 mm Table movement z: 400 mm Spindle intake: MK 5 Spindle speeds: 25-1200 rpm Prests lengthwise & across: 7.5-635 mm/min Presens vertical: 3-250 mm/min Electr. Connection: 380 V, 7.5 kW Space requirement: 1670 x 1500 x 1750 mm Weight: 2600 kg

Demo Machine Specifications:  Dimensions - 1300 x 1560 x 1210 mm, (with built-in drive and control cabinet)  Dimensions of the packed machine - 1500 x 1800 x 1320 mm,  External dimensions of the mill drum - Ø870 x 1120 mm,  Distance between bearings - 1260 mm,  Height of the drum axis - 860 mm,  Operating capacity - 600 dm3,  Weight of the machine - 641 kg,  Installed power - 5.5 kW,  Input voltage/frequency - 400V/50Hz,  Connector - 32A; 400 V  Milling time range - 1s... 99h59min,  Mill installed on a steel frame,  Drum made of 10 mm steel without inner lining. including first filling 80 mm steel balls Technical specification:  Dimensions - 1300 x 1560 x 1210 mm, (with drive and control cabinet installed)  Dimensions of the packed machine - 1500 x 1800 x 1320 mm,  Mill drum external dimensions - Ø870 x 1120 mm, � ...

Qty. 1 Second-hand cold rolling mill Mfc.: MCC, ABB, IMS Type: 6-Hi Cold Rolling Mill Built: 2009 Stopped: 2017 Annual capacity: 220,000 Ton/Year Annual running time (Hour): 6480 Strip Width: 800~1250 mm Thickness Entry: 1.5~3.5 mm Exit: 0.2 – 1.2 mm De-Coiler OD: 1000~2000 mm De-Coil ID: 610 mm De-Coil Weight: Max. 25 T Coil OD: 1000~2000 mm Coil ID: 610 mm Coil Weight: Max. 25 T Mill Max Speed: 1300 m/min Threading Speed: 30 m/min Main Drive Controller (3300 VAC) Mfc.: ABB ACS6000 Variable Speed Variable Voltage Xray Gauge Mfc.: IMS Germany Automation Siemens PLC/Wincc

Control system Heidenhain TNC 415 Spindle diameter 130 mm Tapered hollow spindle ISO 50 Spindle speed range 10 to 1500 rpm Table transverse (X): 3500 mm Rolling headstock stand for (Y): 2000 mm Longitudinal displacement rack (W): 1250 mm Eject working spindle (Z): 800 mm Table load 12 000 kg Machine weight: 36 000 kg

Used hammer mill made by Alpine, type B 630. Manufacturer's documentation.

TOS WHN 130 MC used machine Specifications System Heidenhain TNC 426 Working range Spindle diameter 140 [mm] Taper in the spindle ISO 50 Table transverse adjustment (X) 3000 [mm] Vertical headstock adjustment (Y) 2000 [mm] Vertical travel (Z) 1250 [mm] Spindle stroke (W) 560 [mm] 2X Clamping surface 1800 x 1600 [mm] Speed range 10 - 2500 [rpm] Main motor output 37,0 [kW] Max. workpiece weightƒ 8000 [kg] Accessories Tool changer for 60pcs Tool cooling Chip conveyor

Technical data Spindle dia 125mm ISA 50 taper stroke of the spindle 800 mm cross travel of table X 1200 mm vert. travel of headstock Y 1400 mm longit. ztravel of the table Z 1620 mm spindle speed infinitely variable 3,5-700 rpm table size 1200 x 1400 mm table load 6000 kg main motor DC 19 kw total input 22,79 kW spindle feed inf. variable 0 - 1,25 mm/rot working feeds inf. variable 0,3 - 1700 mm/min rapid traverse 2250 mm/min fine feed 3mm/min dimension LxWxH 7,4 x 4,8 x 3,6 m weight of the machine 21000 kg DRO Heidenhain

Key data: 100 mm, 1600 mm, 1250 mm

DRO , TABLE 1250 X 1250

x-travel 600 mm y-travel 500 mm z-travel 450 mm Control TNC 415 Heidenhain Main spindle: Speed range - milling 20 - 5,000 rpm Drive power - milling spindle 6 / 9 kW Tool holder SK 40 Quill stroke 90 mm Gear stages 4 swivel +/-90 ° Workbench: Bsi0Cso09Qu Table size 900 x 530 mm T-slots 7 T-slots - spacing 63 mm T-slots - width 14-H7 mm max. table load 400 kg Tool Changer: Number of tool positions 18 pos. Tool holder SK 40 max. tool diameter 85 mm max. tool diameter. with a free neighboring box. 150 mm max. tool length 300 mm max. tool weight 10 kg Tool change time max. 15 sec Feeds: Feed rate - fine adjustment 2 ~ 4000 mm/min Rapid traverse X-axis 6,000 mm/min Rapid traverse Y-axis 6,000 mm/min Rapid traverse Z-axis 5,000 mm/min Total power requirement 15 kW Machine weight approx. 3.6 t Dimensions approx. 3.4 x 3.6 x 2.2 m Tool Milling Machine - Universa ...

Skoda W 160 H/NR CNC Travel x= 14.500mm (bed is for the travel 18,500mm) Travel Y= 3.150mm Travel Z= 1.600mm Travel W= 1.250mm Spindle diameter 160mm Machine with ball screw Many accessories available: CNC control Siemens SINUMERIC 850 Rotary table ISO 16 2.200 x 2.200mm, capacity 16 ton included Chip conweyor : 19.000 mm + 12.000 mm Floor plates

W 200G with Siemens AC main motor. modernized the main drive by instalation of Siemens AC motor with SIMODRIVE 611. Original built ISO 60 taper and 630 rpm Main data: X=8000 mm Y=4150 mm Z =1600 mm W=2000 mm Spindle dia 200mm ISO 60 spindle speed max 800 rpm Accessories: DRO Philips available as original rotary table E 20 extra cost milling head IFH 1 and IV25, IFW 1, IFW2 IFW 3 NO floor plates

Fully functional used CNC milling machine Deckel Maho DMU 60 with rotary table Built in 1999 Heidenhain Control We would like to point out that this machine is in excellent technical and well-maintained condition for its age (due to the IATF certification). Regular maintenance is already required on the basis of the certification and the machine therefore works 100% perfectly. The machine is still energized and can be viewed and tested at any time. All maintenance logs are in place. The machine will have to leave the hall in the first quarter of 2025. This means that the machine could remain energized until mid-March 2025 to demonstrate it under power. Of course, the machine would also be available immediately. We will be happy to answer any questions you may have at any time. We are looking forward to a good cooperation and thank you for your answer and interest in adv ...

W100A Parameters 100mm, 1600mm Diameter of working spindle 100 mm Taper in spindle morse 6. Longitudinal adjustment of table (z) 1450 mm Cross adjustment of table (x) 1600 mm Motion of work head on frame (y) 1120 mm Slip out of working spindle (w) 900 mm Clamping area of table 1250 x 1250 mm Dimensions l x w x h 6710 x 3450 x 3000 mm Machine weight 14 000 kg Accessories: face plate, tail stock

CNC Milling-Turning Center Alzmetall GS 600/5-FDT Milling-turning machine Commissioning 05/2021 At call! Heidenhain TNC640 Spindle HSK-T 63 / 18,000 rpm Balancing system (only for FDT) Kinematics Opt Electr. Handwheel Skiving (only for FDT) Dyn. Collision Monitoring Heidenhain DNC Heidenhain Remote Desktop 3D model of the machine Advanced tool management Operating mode 3 Probe Heidenhain Tool Measurement Blum Laser Signal tower on the machine 18,000 spindle HSK-T 63 Continuous air through the spindle (with lubrication interval) Continuous air from the outside 76 mm tool magazine Spray gun Chip flushing of the working area (recommended for Al) Emulsion Mist Extraction Production package C, 80 bar, hinged belt conveyor Machine Interior Trim Remote diagnostics The options list is complete! No interest in dealer enquiries! No separate dealer price! WB me ...

CNC Milling-Turning Center Alzmetall GS 600/5-FDT Milling-turning machine Commissioning 03/2019 At call! Heidenhain TNC640 Spindle HSK-T 63 / 18,000 rpm Balancing system (only for FDT) Kinematics Opt Electr. Handwheel Skiving (only for FDT) Dyn. Collision Monitoring Heidenhain DNC Heidenhain Remote Desktop 3D model of the machine Advanced tool management Operating mode 3 Probe Heidenhain Tool Measurement Blum Laser Signal tower on the machine 18,000 spindle HSK-T 63 Continuous air through the spindle (with lubrication interval) Continuous air from the outside 76 mm tool magazine Spray gun Chip flushing of the working area (recommended for Al) Emulsion Mist Extraction Production package C, 80 bar, hinged belt conveyor Machine Interior Trim Remote diagnostics The options list is complete! No interest in dealer enquiries! No separate dealer price! WB me ...

Qty. 1 Second-hand 4 stands cold rolling mills – 4-Hi Mfc.: Fröhling Built: 1969 Revamped hydraulics: 1984 Dismantled and in storage 2018 Rolled material: Alloy AA5050, AlMg3 (Series 3000 & 5000) Type: 4-Hi Strip width max.: 282 mm Thickness: in 2.0 mm out 0.25 – 1.20 mm Speed max.: 400 m/min

Mfc.: Hitachi Type: 6-Hi reversing mill Built: 1976 Shut down: 2014 Revamped: 2010 Control system – changed DC to AC motors Load cells were replaced in March 2005 & thickness gauge in March 2009 Roll coolant cooler was replaced in July 2009 Control boards of hydraulic screw down & electromagnetic valves were replaced in 2009. Strip width: 610 – 1330 mm Thickness Entry: 1.6-4.5 mm Exit: 0.15 – 2.3 mm

The Section Mill was commissioned in 2011 including advanced rolling mill mechanical equipment alongside electrics and automation systems utilizing Siemens-brand technology. The rolling reutilized a minor portion of the equipment of the previous rolling mill standing there. Those are the finishing mill stands, the high-speed shear before cooling bed and finishing cold shear. Designed for a production capacity of 600,000 tons per year, the rolling mill can process either billets, blooms, or beam blanks into a wide mix of beams, sections, and flat bars. It features a 120 tph walking beam reheating furnace, a breakdown reversible mill (BDM), a three stands ultra-flexible reversing mill (UFR), and an eight-stand continuous finishing mill. The facility is further equipped with advanced finishing services, including straighteners, cutting saws, cold shear, magnetic stackers, and strapping ...

Technical data: Fixed angular table: Fixed angular table clamping area: 800 x 400 mm Max table load: 200 kg Working spindle: Tool holder horizontally and vertically: ISO 40 Power of the main drive motor / 100% ED: 2.2 kW Vertical milling head: Speed range, tiered: (12) 50 - 2000 rpm Drill pinole, stroke: 100 mm Swivel range: +/- 90° Travel: X-axis automatic/man.: 385/400 mm Y-axis automatic/man.: 185/200 mm Z-axis automatic/man.: 365/380 mm Feeds: Feed range: 0-650 mm/min Number of feeds: infinitely adjustable Rapid response: 1000 mm/min Characteristics: - Machine accuracy according to DIN 8615 - 3-axis digital displays FAGOR® Innova (option) - Spindle run max. 0.005 mm, incl. test protocol according to DIN 8615 (rolling bearing SKF®/NSK®) - Vertical milling head can be swivelled out for horizontal milling (without d ...

Star Ball Mill, Rotor Ball Mill, Centrifugal Ball Mill, Centrifugal Ball Mill Used. Manufacturer: EHINGER IMPIANTI Type: RM 150 Achievable grain sizes: with dynamic classifier: 0-20 μ and 0-300 μ with static selector 0-2 mm Average continuous output approx. 1.6 t of glass per hour Motor SIEMENS 75 kW 738 rpm 400 V Dimensions approx. 2850 x 4100 x 5000 mm original matching dust filter with fan The mill pictured serves only as a sample. The mill for sale is currently being revised. These mills are now being built by Eirich as an OrbitMill for the fine grinding of industrial minerals. Performance data of the Orbit Mill according to the manufacturer as an example of limestone. Air flow rate 13000 m³/h Limestone Throughput d97= 20 μm : 1.6 t/h d97= 40 μm : 3.3 t/h d97= 105 μm : 6.0 t/h The mill pictured was used in glass recycling. Four balls, which a ...

AVIAN Engineering Model G46/ 60 Pinch Infeed Rollers Integral Blower Main Motor 20 kW Blower Motor 2 kW Rotary Blade 6pcs Stationary Blade 4pcs ThruPut 300 KG/H Cutting Chamber 620 x 460mm Hopper Opening 620 x 500mm

Stock# U2448-1 Used pin mill by Jehmlich (Germany) model Rekord D, designed in carbon steel. Mill body made of cast iron. Unit has milling discs with a diameter of 610 mm made of carbon steel. Mill has one fixed and one rotating milling disc driven by a belts driven with an ex proof electric motor with a power of 22 kW, 2945 rpm, 380 V, 50 Hz. Machine is equipped with a carbon steel feeding hopper and bottom unloading. The set includes a stainless steel hopper tank mounted on 4 carbon steel legs and a belt conveyor with a polyurethane fabric/plastic belt with a working width of 245 mm and a length of 3800 mm, conveyor construction is made of carbon steel and mounted on legs. The belt is driven by a gearbox with a ratio of i=15, an ex proof electric motor with a power of 1,1 kW, 1415 rpm, 380 V, 50 Hz. Whole thing is mounted on a frame made of carbon steel. Also includes a spare set of ...

Travel X-axis 19,000 mm Y-axis 3,500 mm Z-axis 1,000 mm W-axis 1,000 mm V-axis 2,500 mm B-axis 360°/ 0.001 Table size 4,000 x 3,500 mm Maximum permissible weight on the table 65 t Spindle diameter 160 mm Mounting cone in spindle 2079 DIN/ ISO 50 Spindle speed 2.5 - 1,000 rpm Spindle motor power 90 kW RAM cross section 400 x 400 mm Automatic tool changer 60 positions Feed in all axes 1 - 6,000 mm/min Rapid response in all axes 10,000 mm/min Automatic indexing 360,000° Plate field 12,750 x 6,000 mm CNC, electrical and mechanical overhaul by Siemens in 2003

Blade length 205 mm Max cutting performance Sheet R = 42 kg / mm2 4 mm Sheet R = 70 kg / mm2 3 mm Engine power 3 kW Number of beats / minutes 50 min Table dimension 625 x 954 mm Capacity of the oil tank 25 l Weight 500 kg The setting between the blades is fully automatic. Standard: - 1 set of knives at 30 ° (mounted on the machine) - 1 stop switch - 1 general circuit breaker - 1 stop adjustable and adjustable every 15° - Fill the first oil - Manual with installation and maintenance instructions and service keys.

CNC Milling Machine Universal Manufacturer: HERMLE Type: UWF 902 S Year of Make: 1995 Hours: 65 071 Control: HEIDENHAIN TNC 426 Working area X/Y/Z: 600 x 450 x 500 mm Range: Spindle speeds infinitely variable within 3 switching stages: 20 to 6,300 rpm Tool holder: SK40 Tool Changer Tool holder, horizontal and vertical: ISO 40 DIN 2079 Tool clamping hydromechanical, clamping force (vertical): 10 000 N Tool clamping hydromechanical, clamping force (horizontal): 12 000 N Spindle diameter on front bearing, horizontal / vertical: 75 / 55 mm Quill Ø 100 mm extendable vertical: 75 mm M & H 3D Probe Individual feed motors for each axis – three-phase current (brushless) Feed range in X, Y, Z manual / program-controlled: 1 to 2000 / 10 000 mm/min. Feed force in all axes (at 80% DC): 6 000 N Rapid traverse in all axes: 10 m / min. Angle table: 900 x 458 mm Table wei ...

Travel X-axis 9,500 mm Y-axis 4,100 mm Z-axis 950 mm W-axis 900 mm Main spindle speeds (infinitely adjustable): 3.15 - 1000 rpm Spindle motor power 58 kW Feed speed (infinitely adjustable): X-axis 0.1 - 9600 mm/min Y-axis 0.1 - 5600 mm/min Z-axis 0.1 - 5600 mm/min W-axis 0.1 - 5600 mm/min Accessories: Plate field: 6 x 4 m (CNC-controlled B- and V-axis) Table: 2 x 2 m (CNC-controlled B- and V-axis)

CNC Milling Machine Universal Manufacturer: HERMLE Type: UWF 902 H Year of Make: 1995 Hours: 46,680 Control: HEIDENHAIN TNC 426 Working area X/Y/Z: 600 x 450 x 500 mm Range: Spindle speeds infinitely variable within 3 switching stages: 20 to 6,300 rpm Tool holder: SK40 Tool Changer Tool holder, horizontal and vertical: ISO 40 DIN 2079 Tool clamping hydromechanical, clamping force (vertical): 10 000 N Tool clamping hydromechanical, clamping force (horizontal): 12 000 N Spindle diameter on front bearing, horizontal / vertical: 75 / 55 mm Quill stroke vertical: 75 mm Renishaw 3D Probe Individual feed motors for each axis – three-phase current (brushless) Feed range in X, Y, Z manually / programmatically: 1 to 2000 / 10 000 mm/min. Feed force in all axes (at 80% DC): 6 000 N Rapid traverse in all axes: 10 m / min. Angle table: 900 x 458 mm Universal clamping  ...

x-400,y-330,z-350,angle table 630x335,SK 40, 40-6,000 rpm,measuring probe

Manufacturer: IMA Radienschleifaggregat, Number of motors: 1, kW-Leistung : 1,75, Drehzahlen U/min : frequenzgesteuert, Vertical roller sensing: yes, Slewable horizontally: 400x700x900, Slewable vertically: yes,

Manufacturer: Homag, Type: Schnellwechselköpfe FK 11 / FK 13, FREE TEXT: Preis je Stck,

Table clamping area: 310 x 1400 mm Table movement x: 950 mm Table movement y: approx. 325/345 mm Table movement z: approx. 500 mm Spindle speeds: 20 - 1500 rpm Feeds longitudinally and transversely: 18 - 620 mm/min Feeds vertical: 18 - 620 mm/min electr. Connection: 380 V kW Space requirement: 1900 x 1600 x 1750 mm Weight: approx. 1500 kg

Manufacturer: Homag Nutsäge mit Winkelgetriebe, Type: 4-00570, Saw blade quantity: 1, Tool diameter mm: ca.160, Used: yes, Anschlussspindel mm: HSk 63, Available: sofort, FREE TEXT: HSK 63 ,

Manufacturer: Homag, Type: 4-00570, Tool diameter mm: ca.160, Used: yes, HSK 63: yes, Angle saw: yes, FREE TEXT: Aggregat ohne Hauben mit Tastschuh/ 9000 U/min,

Qty. 1 Second-hand Sendzimir rolling mill Mfc.: INNSE Type: ZR-22- 49” Built: 1960’s Strip width: 1270 mm Thickness Entry: 5.0 mm Exit: 0.4 mm Mill motor: 1640 kW, 2200 HP Qty. 2 Reel motors: 932 kW, 1250 HP Rolling speed: 0 – 163/288 m/min. Max. coil dia.: 1574 mm Winder mandrel dia.: 610 mm Coil weight: 21 Tons Max. tension: 300 kN Max. roll separating force: 6000 kN Work rolls dia.: 48-61 mm