bed type mill used for sale

Key data: 290 , 400

Machine-Details Stock-No. 1105-04007 Type of machine CNC Lathe - Inclined Bed Type Make GILDEMEISTER Type CTX 210 Year of manufacture 2005 Type of control CNC Storage location FRANKREICH Country of origin Germany Delivery time IMMIDIATELY Freight basis EX WORKS Technical details Turning diameter 290 mm turning length 365 mm control SIEMENS 840 D SIEMENS 840 D Greates Pass round over bed 380 mm X-Travel 160 mm Z-Travel 365 mm spindle head 120 H 5 mm Boron spindle 56 mm bar material dia. 42 mm Spindle diameter in front bearing 90 mm turning speed range 20 - 6000 U/min spindle drive 10 kW No. of tools in turret 1 12 x VDI 30 total power requirement 22 kW Weight of the machine ca. 4,2 t Dimensions of the machine ca. 2.8 x 1.7 x 1.8 m Additional information NICE MACHINE CNC SIEMENS 840 D SOMME TOOLS VDI 30 TOOL MESURING Arm TAILSTOCK CHIP CONVEYER

Fluid Bed Dryer Type: DCRVF1200x7 Rationale: The material to be dried is placed on the inflow floor and fed there from bottom to top with the Drying air flows through. As a result, the good is heated with constant vibration and the moisture driven out. The vibration prevents the formation of bubbles in the fluidized bed of fine-grained products as well as the Segregation for products with a broad grain spectrum. The vibration also loosens up coarse grains and an almost complete emptying of the entire body. The dwell time of the product can be reduced by adjustment of the vibration. Specifications: Dryer width: 1200 mm Overall length: 7.0 m Length of the dry zone: 4.25 m Length of the cooling zone 2.75 m Tilt: horizontal Execution: · Air flow trough in welded steel construction with the necessary inlet and outlet openings · Exhaust hood with expansion zone, the necessar ...

\" Power: 125 kW (3.0 diesel); Euro N/C Operating parameters: Manual gearbox; mileage 413,000+ km; GVW truck 3.5 t; GCW (comb.) 10 t; ABS; cruise control Workpiece capacity: BE-combination 10 t; open trailer; dim. L 12,300 mm x W 2,550 mm x H 1,100 mm; full aluminium body; winch; 13–15 pin connector Supported edges: N/A Edge types: N/A Included equipment: A/C (Klima); Webasto heater; air seat; ABS (truck + trailer); new tyres (6x truck + 4x trailer); rear brakes replaced; compressor hose new; turbo new; EGR cooler new; complete timing chain kit; prop shaft bearings + joints; all oils + antifreeze new; trailer: new air bags, valves, wheel bearings, full new lights + wiring Compliance: BE driving licence combination; road registered vehicle Power supply: Diesel Year/Manufacturer: 2012 / Iveco Daily 40C17; trailer 2007; aluminium construction Remarks: High mileage; exten ...

Tip distance approx.                                                    400 mm Tip height above bed 130 mm 12 speeds from 125 – 2800 rpm Space requirements, length x width 1.2 x 0.6 m Weight estimated approx.                                          400 kg

Specifications: Maximum turning length 90 mm Circulation diameter over bed 220 mm Circulation diameter over support 110 mm Center width 160 mm Bore 23 mm 3 speeds 350 / 700 / 1400 rpm

Tip distance approx.                                                    500 mm Tip height above bed 125 mm 16 speeds from 120 – 1800 rpm Space requirements, length x width 1.2 x 0.6 m Weight estimated approx.                                          450 kg

Center height 110 mm Center width 160 mm Spindle bore 23 mm Motor power 1.7 kW . Speeds : 700 - 1400 - 2800 rpm .

Specifications: Center height 110 mm Center width 160 mm Spindle bore 23 mm Motor power 1.7 kW in each case rotational speed via potentiometer To be set from approx. 100 – 2,300 rpm 3 preset speeds or 3 switching stages

unfolded width approx. 110 cm. Auction-ID: A1-44654-272

Spacing : 2000 mm Permissible diameter on bench : 720 mm Diameter on straggler : 430 mm X stroke : 410 mm Z stroke : 2000 mm Spindle speed : 1 – 1800 rpm Spindle bore : 106 mm Spindle nose : DIN 55027 size 11 Installed power : 28 kW Power supply : 400 V Lots sold as is, unchecked, without tools or tool holders.

FLUIDISED BED Drier/ Cooler BUHLER OTW 150, with a complete peripherical ( see description) in very good condition, was stored for years and NOT USED Suitable for pellets, cereal flakes, extrudates...many other types of materials.or products.. Come along with it : 2 fans, a very nice cyclone , a steam battery to pulse hot air, pipes... Can be used according to alternative ways : whether to dry out materials.. or to cool, a simple inversion of hot or cool air has to be choosen More pictures available, great money spares compared to a new one... Can be shipped to any destination

BUHLER OTW 150 fluidized bed dryer/cooler, with a complete device (see description) in very good condition, has been stored for years and NOT USED Suitable for pellets, cereal flakes, extrudates... many other types of materials. or products. Sold with: 2 fans, a very nice cyclone, a steam battery to pulse hot air, hoses... Can be used in alternative methods: whether for drying materials. or to cool, you have to choose a simple inversion of hot or cold air More photos available, a lot of spare money compared to a new one... Can be shipped to any destination

turning diameter: mm turning length: mm control: 0 total power requirement: kW weight of the machine ca.: t required space: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stainless Steel Control Box, Control Cabinet PAGUS 6AV3515-1MA22-1AA0 with Control Panel SIEMENS Operation Panel Coros OP 15-C2 SIEMENS Bus Terminal RS485 6GK1500-0AB00 used, tested ! Dimensions: 785 x 180 x 885 mm

Stainless Steel Control Box, Control Cabinet PAGUS 600 x 245 x 775 mm ( 600x245x775mm ) with control panel SIEMENS Operation Panel Coros OP 15-C1 6AV3515-1MA20-1AA0 SIEMENS 6ES7 214-1AC01-0XB0 6ES7 223-1HF00-0XA0 Dimensions: 600 x 245 x 775 mm

turning diameter: 800 mm turning length: 900 mm control: Fanuc 0 total power requirement: kW weight of the machine ca.: t required space: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stock number: D726, Coater/fluid bed, stainless steel,, Niro type Combi Coata II,, for filmcoating tablets/capsules/granulates., Electric heating., Sprayfunction ex. pump., 20 l. product container., Material: Stainless steel AISI 304

Stock number: D699, Fluid bed, stainless steel,, type EB 20, for filmcoating of caps./tablets., Electric heating., 20 l. product container., Watson-Marlow feed pump., Steering panel., Material: Stainless steel AISI 304

Stock number: D693, Hose fluid bed table, stainless steel,, with heat and blower and timer,, with space for 5 pc. hose., L 3750 x W 620 mm., Material: Stainless steel AISI 304

• Suitable for drying and granulation (intended for preparations for in vitro diagnostic use) • Batch operation • Peristaltic pump for spray liquid • Top spray nozzle for spray liquid • Scales • Product container volume 24 L • Batch volume max. 16 L • Batch weight 1-8 kg (depending on product) • Product suction lance from Müller barrel • Conical transition piece for emptying into Müller barrel • Heating register • Star filter for separating product and air flow • Inflatable seals • Product temperature max. 85°C • Explosion-proof container • Max. explosion pressure 10 bar • ATEX Zone 20 inside the mixer (according to conditions in 2010) • Equipment category 1 according to Directive 94/9/EC • Equipment group II, D (dust) • Protection class IP 5x • Max. surface temperature 180°C • Operator terminal MP 277 Touch • Process data acquisition with ...

Features: automatic non-stop delivery with conveyor, non-stop feeder with rods, pull mark left, push mark right, quick clamping frame for tooling, lower stripping station, upper stripping station, two exchange frames for lower stripping station. Without die-cutting plates. Processable materials: min. paper 90g/m², max. solid board 2000g/m², max. corrugated board/ with MasterSet 4/ 2mm, max. sheet size 760x1060mm, min. sheet size/with MasterSet 300x350/ 350x400mm, max. cutting pressure: 2.6MN/ 260t, max. machine speed: 8000 sheets/h, max. feeder pile height without non-stop/ in non-stop operation: 1500/ 1200mm, max. feeder pile weight: 1500kg, max. delivery pile height: 1400mm, max. delivery pile weight: 900/ 1340kg. Operating hours: 1525h. An on-site inspection is possible.

A Ueda Shiko Kikai (Seiko) flatbed die-cutting machine from the 1980s is available. Throughput capacity: approx. 3600 sheets/h, max. sheet length: 1370mm, max. sheet width: 970mm, min. sheet format X/Y: 530mm/300mm, machine dimensions X/Y/Z: approx. 8150mm/2350mm/2050mm, weight: approx. 20000kg. An on-site inspection is possible.

turning diameter: mm turning length: mm control: 0 total power requirement: kW weight of the machine ca.: t required space: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

A slant bed lathe Traub Sonim is available. Turning diameter over bed/cross slide: 350mm/160mm, turning length: 200mm, speed: 5000rpm. Machine dimensions X/Y/Z: approx. 3200mm/1500mm/1700mm, weight: approx. 3500kg. An on-site inspection is possible.

CONTROLS   CNC controls TRAUB TX 8 BASIC FUNCTIONS   number of spindles: 1   number of x/z slides: 1   number of turrets: 1   live positions: yes   number of c-axes: 1 WORKING RANGE TURNING   swing diameter (max): 450 mm   turning diameter (max): 350 mm   bar diameter (max): 60 mm   worpiece length max.: 490 mm MAIN SPINDLE   spindle revolutions (max): 4000 /min   c-axis: yes TOOL MAGAZINE   number of positions: 12 ELECTRICAL SPECIFICATIONS   total power consumption: 39 kW   mains voltage: 400 V   mains frequency: 50 Hz DIMENSIONS / WEIGHTS   space requirements -left/right-: 3150 mm   space requirements -front/back-: 2100 mm   total height: 2100 mm   total weight approx.: 4000 kg ATTA ...

Power: 2,000 W CW Fiber Laser; λ 1,064 nm; upgrade-ready 500–18,000 W Operating parameters: Max. speed 120 m/min; positioning repeatability ±0.02 mm; auto Z-axis height ctrl. (BCS100 V3.0); auto central lubrication Workpiece capacity: 2 exchange tables 3,050 x 1,550 mm each; double-bed system; machine dim. L 7,850 x W 2,350 x H 1,950 mm Supported edges: Steel, stainless steel, Al, Cu, brass & other metals (fiber laser cutting) Edge types: High-precision 2D metal cutting; contour + nesting operations Included equipment: Laser source (Raycus/Max/IPG); Raytools cutting head w/ auto focus; servo motors (Schneider/Yaskawa) – Y: 2x 2,000 W (dual drive), X: 1x 1,000 W, Z: 1x 400 W; planetary reducers Apex (USA); linear guides HIWIN; CypCut control + nesting software; wireless remote; Hanli HL-3000 chiller (laser + head) Compliance: Industrial CNC fiber laser system; CE N/ ...

Manufacturer: WFS YOM: 2001 W090011081RW72071 Serial number S/81283 Car transport approved in documents new air cushions no rust in perfect working condition Dimensions 8700 x 2300 mm weight 5000 kg Unladen 1700 kg Auction-ID: A7-40551-19

A defective flatbed die-cutting machine IMG Klett is available. Chase inner dimensions X/Y: 1630mm/1210mm, max. cutting dimensions X/Y: 1600mm/1180mm, min. sheet dimensions X/Y: 650mm/450mm, max. sheet dimensions X/Y: 1200mm/1620mm, min. sheet thickness: 1mm, max. corrugated board thickness: 8mm, max. plastic corrugated material thickness: 8mm, gripper margin waste area: 9mm-15mm, max. cutting force: 400t, motor power: 22kW. Machine dimensions X/Y/Z: approx. 7550mm/5200mm/2450mm, weight: approx. 32000kg. Documentation available. An on-site inspection is possible.

SS + SC standard bed centre lathe, 1000mm between centres, 220mm swing over bed, with 3 jaw chuck, with 18 spindle speeds from 21 rpm to 1500 rpm Auction-ID: A1-45187-213

Without support and contents, including vice Auction-ID: A1-45406-8

Spacing : 2000 mm Permissible diameter on bench : 720 mm Diameter on straggler : 430 mm X stroke : 410 mm Z stroke : 2000 mm Spindle speed : 1 – 1800 rpm Spindle bore : 106 mm Spindle nose : DIN 55027 size 11 Installed power : 28 kW Power supply : 400 V Lots sold as is, unchecked, without tools or tool holders. Auction-ID: A1-44765-206

Equipped with pointed roof with balcony/canopy 2 meters long; insulated walls and roof; 2 bedrooms; living room with corner kitchen; bathroom with shower, toilet and sink; each room equipped with lighting and sockets 230V; meter cupboard; PVC floor; aluminum windows and doors; lockable; water, electricity and drainage can be easily connected is prepared; unused and ready for transport (note furniture not included) (transport dimensions 590x220x248 cm, weight 3100 kg) Auction-ID: A1-40103-12

Brand : Hedin Lagan AB Type : Forklift heavy duty bed trailer Dimension l : 620 cm Dimension w : 235 cm Dimension h : 95 cm Auction-ID: A1-42013-52

Equipped with insulated walls and roof; 2 bedrooms; living room with corner kitchen; bathroom with shower, toilet and sink; each room equipped with lighting and sockets 230V; meter cupboard; PVC floor; aluminum windows and doors; lockable; water, electricity and drainage can be easily connected is prepared; unused and ready for transport (note color is stone motif as in the first photo) (note furniture not included) (note this model does not have a glass wall on the left side wall photos are for illustration, inside it is exactly the same) (transport dimensions 590x220x248 cm, weight 3500 kg) Auction-ID: A1-40104-45

Equipped with insulated walls and roof; 2 bedrooms; living room with corner kitchen; bathroom with shower, toilet and sink; each room equipped with lighting and sockets 230V; meter cupboard; PVC floor; aluminum windows and doors; lockable; water, electricity and drainage can be easily connected is prepared; unused and ready for transport (note furniture not included) (transport dimensions 590x220x248 cm, weight 3100 kg) Auction-ID: A1-40104-46

With residual content, content may differ from the pictures Auction-ID: A1-45711-18

Table clamping surface: 500 x 1600 mm table movement x: 1220 mm table movement y: 500 mm table movement z: 500 mm spindle retainer: SK 50 spindle speeds: 56-2800 rpm feeds longitudinal & cross: 10-1800 mm / min feed vertically: 2.5-450 mm / min. Supply: 400 V, 16 kVA kW space: 2000 x 2250 x 2150 mm weight: 4500 kg

Vertical -consol milling machine, used    Vertical -milling machine, used Make/make: WMW HECKERT Type/ model: FQS 400 Year built: 1978 Control type / control: conventional   x-way: 1190 mm   y-way: 530 mm z-way: 540 mm Table size/ table: 1600 x 400 mm Spindle power/ spindle power: 11kW Tool holder/tool taper: ISO 50 Speeds/ speeds: 28 - 1400 rpm Feeds: 16- 800 mm/min Total power requirement: 21 kW Machine weight: 4.8 t  

Spindle diameter 203.2 mm x-travel 9,000 mm y-travel 4,000 mm Grinding spindle diameter 335 mm Spindle holder ISO 60 Spindle speeds 1-350 / 5-1,200 rpm w-axis 800 mm z-axis 1,200 mm Rapid x-axis 8,000 m/min Rapid y-axis 6,000 m/min RAM Dimensions 530 x 600 mm Main drive 75 kW Total power requirement 165 kW Machine weight approx. 130 t Space requirements approx. 16 x 5.5 x 8.1 m Addition: - hydrostatic guides in x-, y- and w-axis - Telescopic cover for the X-axis of the bed - cumulative Z and W axes - Leveling shoes - Platform Y axis

GeneralVertical Machining Centres; Control: Control F0iMF CharacteristicsTable surface1400 x 560 mmDimensions (L x W x H)3,19 x 2,76 x 2,94 (3,82 x 3,58 x 3,01) mRapid feed X / Y / Z36/36/30 m/minMovement X / Y / Z1100/560/510 mmSpindle taperBT 40 Tool Magazine with60 PositionsDrive power (25% DC)15 kWDrive power (100% DC)11 kWSpeed max.12000 rpmMaximum load (table centre)1000 KgWeight approx.5500 KgStandard spindle 12,000 min-1, 15/ 11 kWStandard Spindle 12,000 min-1, 15/ 11 kW Spindle speed: 12,000 min-1 Output: 15/13/11 kW (20/17.33/15 HP) (25%ED/30min/cont) Torque: 119/70/57 Nm (87.76/51.62/42.04 ft·lbf) (25%ED/30min/cont)Spindle Taper 7/24 Taper #40/ Grip MAS Spindle Taper 7/24 Taper #40/ Grip MAS This specification uses the spindle No. 40 7/24 taper / Grip MAS tool holder. The grip type and retention knob type of ATC are specified separately.Retention Knob: Special (Center-Throug ...

TECHNICAL DATA SHEET CNC – Gantry gantry milling machine TRIMILL brand Type VF3016 Year of construction 2017 Control HEIDENHAIN iTNC530 HSCI Travel X-axis (longitudinal): 3,000 mm Y-axis (transverse): 1,600 mm Z-axis (vertical): 1,200 mm B-axis (swivel axis milling head) +/- 100 ° C-axis (rotation axis milling head) +/- 240 ° Structure / Axis concept AC servomotors with digital control for all axes Gantry drive of the X-axis Rack and pinion drive in the X-axis, backlash-free due to electrically prestressed, water-cooled motors 2 ball screws each in the Y and Z axes Guides of all linear axes are designed as prestressed roller guides Hydro-pneumatic weight compensation of the Z-axis via 2 cylinders Stationary frame components made of mineral casting, movable main components made of grey or nodular cast iron Double beams in load- and thermosymmetric d ...

Key data: 850 mm, 270 mm, 355 mm

Table width 315 mm, table length 1250 mm Tool holder SK 50 Speed range 28 - 1400 rpm Feed range 16 - 800 mm/min Travel x=850 mm, y= 270 mm, z=355 mm Connected load 8 kW Incl. Electric clamp horizontal Vertical head in X swivel with manual tightening Dispensing as present, no longer energized

Code 4923 DESCRIPTION Universal milling machine Make DEBER Model FU 1 Serial No. 228 Year Table 1250 x 300 mm Longitude table 750 mm Vertical table 405 mm Cross table 240 mm Spindle taper 40 ISO Speeds 40 - 2000 rpm Feeds X-Y-Z 14 - 700 mm/min Rapides 1 and 2 m/min Spindle motor 5,5 kW - 380 Volts Weight of machine 2000 kgs Accessories universal millinghead ( 2 x turnable ) Coolant Condition Machine is in very good condition

Quantity: about 190 pieces Type: HSK63 Status: Opportunity Set including numerous HSK63 tool holders, ER collet chucks, cutter holders, face heads, boring heads, adapters, cones and various accessories, presence of mounted carbide cutters, different diameters and lengths, storage in wooden crates

Key data: 4700 mm, 6100 mm, 1470 mm

Portal milling machine with fixed portal and 2 separately movable machine tables for pendulum machining. The tables can be coupled to form a large table. Designed for the typical applications in model and mould making and in the machining of (small) series parts with high efficiency. In addition, the machine can be equipped with a zero-point clamping system for quick replacement of clamping fixtures or prepared parts. Areas of work: X-axis: 4,700 mm Y-axis: 6,100 mm Z-axis: 1,470 mm A-axis: ± 115° C-axis: ± 360° Control: OSAI Openkey 2-axis milling head with spindle: Spindle power: 15 kW Spindle speed: max. 24,000 min-1 Torque: 20.9 Nm Tool holder: HSK 63F Tool tensioning: pneumatic blowing air / MQQ: outside Clamping table: Clamping surface: 2 x 1,950 x 2,500 x 213 mm (coupled: 4,000 x 2,500 mm) Aluminium with grid threaded holes Max load: 1000 kg distributed over th ...

Key data: 1120 mm, 345 mm, 550 mm

Table width 400 mm, table length 1600 mm Tool holder SK 50 Speed range 28-1400 rpm Feed range 16-800 mm/min Travel x 1120 mm ; y 345 mm; z 550 mm Connected load approx. 14.5 kW Accessories: 2 counter bearings Electric clamp horizontal and vertical spindle Vertical milling head SK50 with snap bearing

Key data: 1400 mm, 630 mm, 500 mm

Table size 1800 x 630 mm Speed range 56 - 2800 1/min Tool holder ISO 50 Travel X / Y / Z 1400 / 630 / 500 mm Feed range X, Y 10 - 2000 (Z 2.5 - 500 ) mm/min infinitely variable Main motor 15 kW, connected load approx. 20 kW Incl. Universal milling head IUG 32A swivel 360° horizontal milling spindle Rapid traverse, automatic cycle Digital display Heidenhain ND 750 Coolant Setup Work area cladding hydraulic tool clamping CE Declaration of Conformity

GeneralVertical Machining Center; Control: Control SIEMENS 828D CharacteristicsSpeed max.12000 rpmDimensions (L x W x H)3,07 x 2,67 x 2,84 mRapid feed X / Y / Z24/24/24 m/minMovement X / Y / Z550/550/510 mmSpindle taperSK 40 DIN 69871 Tool Magazine with24 PositionsMax. torque83 NmTorque (100% DC)57 NmDrive power (40% DC)13 kWDrive power (100% DC)9 kWTable surface850 x 650 mmWeight approx.5600 KgMechanical preparation for Oil-Mist Extractor UnitMechanical preparation for Oil-Mist Extractor Unit (opening diameter: D150 mm)4th Axis package4th Axis package Option includes: - rotary table type EA-510.L NE with indirect measuring system - electrical and pneumatic preparation - software preparation to work with rotary table - cycle TRACYL which allows to define contour on the cylinder - swSK40 interfaceTool clamping SK 40 for pull-studs DIN 69872Electronic HandwheelExternal electronic Handwhe ...

CharacteristicsTable surface850 x 650 mmWeight approx.5600 KgRapid feed X / Y / Z24/24/24 m/minMovement X / Y / Z550/550/510 mmSpindle taperSK 40 DIN 69871 Tool Magazine with24 PositionsMax. torque83 NmTorque (100% DC)57 NmDrive power (40% DC)13 kWDrive power (100% DC)9 kWSpeed max.12000 rpmDimensions (L x W x H)3,07 x 2,67 x 2,84 mGeneralVertical Machining Center; Control: Control SIEMENS 828D Mechanical preparation for Oil-Mist Extractor UnitMechanical preparation for Oil-Mist Extractor Unit (opening diameter: D150 mm)4th Axis package4th Axis package Option includes: - rotary table type EA-510.L NE with indirect measuring system - electrical and pneumatic preparation - software preparation to work with rotary table - cycle TRACYL which allows to define contour on the cylinder - swSK40 interfaceTool clamping SK 40 for pull-studs DIN 69872Electronic HandwheelExternal electronic Handwhe ...

GeneralVertical Machining Center; Control: Control SIEMENS 828D CharacteristicsTable surface850 x 650 mmDimensions (L x W x H)3,07 x 2,67 x 2,84 mRapid feed X / Y / Z24/24/24 m/minMovement X / Y / Z550/550/510 mmSpindle taperSK 40 DIN 69871 Tool Magazine with24 PositionsMax. torque83 NmTorque (100% DC)57 NmDrive power (40% DC)13 kWDrive power (100% DC)9 kWSpeed max.12000 rpmWeight approx.5600 KgMechanical preparation for Oil-Mist Extractor UnitMechanical preparation for Oil-Mist Extractor Unit (opening diameter: D150 mm)4th Axis package4th Axis package Option includes: - rotary table type EA-510.L NE with indirect measuring system - electrical and pneumatic preparation - software preparation to work with rotary table - cycle TRACYL which allows to define contour on the cylinder - swSK40 interfaceTool clamping SK 40 for pull-studs DIN 69872Electronic HandwheelExternal electronic Handwhe ...