129,495 used machines on RESALE, but how to find them? Machine Search
Key data: 83 KW, 100 kVA
We currently offer: Number 58 Gesan generator set Type: DRP 100 Engine Perkins Generator LeRoy Somer Power: 83 KW / 100 KVA Hz 50 IP 23 Year of construction 2013 Hours: 15170 AVR regulation R438 Weight: 1906 kg We suspect that the engine has some damage. On the pictures you can also see that the water pump is missing and a sensor. You can find more machines on our website. If you have any further questions, please feel free to contact us. Adel e.K. Commercial Vehicles-Construction Machines Car Recycling Machine Dismantling Gottlieb-Daimler Str. 26 D-74831 Gundelsheim Phone: 0049 1796710242
Lippert Belt Conveyor Folding Belt Switch track conveyor belt 1045-650-500 RA1366 The Lippert conveyor belt is from 2001 and in good (used) condition. The belt conveyor has a SEW motor with MOVIMOT frequency inverter to control the speed. Lateral guides and/or light barriers can be installed on request at extra cost. Supports are not included in the delivery. These are optionally available on request. The pictures of the conveyor system shown here were taken in a logistics center while still installed. The conveyor belt was used as a folding belt. Folding device was removed during dismantling. On request, we can also supply this conveyor belt as a folding belt version. Technical data: Conveying length (NL): 1045 mm Framework width (NB): 650 mm belt width (GuB): 500 mm height (BH): 105 mm support feet: optionally available Conveying speed (v m/s): adjustable up and down with frequency co ...
Transnorm belt curve conveyor left 90°-1000-800-IR900 RA2001 Belt curves are frequently used in intralogistics for the internal transport of unit loads and are an indispensable part of modern distribution centers. Transnorm belt curves convince with performance and reliability. Thanks to a low-tension drive, over the entire belt width, long operating times are no problem. Conical drums and a specially developed belt guide system ensure the smoothest possible running. Technical data: Type designation: belt curve conveyor Stand width (NB): 1000 mm Belt width (GuB): 800 mm Motor width (MB): +200 mm overall height (BH): 210 mm inner radius (IR): 900 mm Conveying angle: 90° degrees Conveying speed: Please contact Drive: SEW gear motor with Movi-Mot Electrical data: 50Hz V230/400, kW 0,37 /S1 Year of construction: 1992 Included: Side guide on both sides and frame Optionally available: Suppo ...
pressure: 1000 t distance between columns: 5000 mm stroke: 500 mm Height of centres: 400 mm Motor output: kW reus: U/min Overall size: 6000 x 2500 mm Weight: 1000 kg Distance between centres: 3500 mm total power requirement: kW weight of the machine ca.: 220 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Transnorm belt curve conveyor left 30°-1270-1100-IR900 RA2303 Technical data: Frame width (NB): 1270 mm Frame width with Bearing cover: 1390 mm Frame width with Bearing cover and gearbox: 1480 mm belt width (GuB): 1100 mm height (BH): 250 mm height motor below: 300 mm height including motor (MH): 550 mm Inner radius (IR): 900 mm Conveying angle: 30° degrees middler conveying speed (v m/s): 1,0 m/s Drive: SEW motor motor with frequency converter Electrical data: 50Hz V380-500, kW 1,5 / S1 Belt: KT 96 new Year of construction: 2021 Height Sideguides: 194 mm Optionally available: Supports Prices net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2021 condition: new Nominal / inner radius in mm: 900 Nominal / outside width in mm: 1270 Belt width in mm: 1100 angle: 30° Driven: YES Running direction: LINKS Engine type: SEW Eurodrive K ...
Transnorm spiral helix belt curve conveyor left 90°-775-600 IR600 RA2008 The Transnorm belt curve conveyor is in good condition (used) and fully functional. It has a gear motor of the brand SEW. Supports and are not included. These are optionally available on request. Belt curves are frequently used in intralogistics for the internal transport of unit loads and are an indispensable part of modern distribution centers. Transnorm belt curves impress with performance and reliability. Thanks to a low-tension drive, over the entire belt width, long operating times are no problem. Conical drums and a specially developed belt guide system ensure the smoothest possible running. Technical data: Type designation: belt curve conveyor TS 1600-105 frame width (NB): 775 mm belt width (GuB): 600 mm overall height (BH): 210 mm inner radius (IR): 600 mm Conveying angle: 90° degrees (coiled 191mm rising ...
Transnorm curved belt conveyor left 90°-800-600-IR600 RA2169 Make: Transnorm Running direction: 90° left running belt conveyor width (RB): 600 mm Nominal/outer width (NB): 800 mm Nominal/outer width with Motor (MB): 1020 mm Inner radius (IR): 600 mm Height frame (BH): 200 mm Height frame with Motor (MH): 400 mm V 220/380, 0,37kW Conveying speed: contat us Optionally available: Supports Side guide one- and both sideds Frequency converter Prices net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 1998 condition: gut Nominal / inner radius in mm: 600 Nominal / outside width in mm: 800 Belt width in mm: 600 angle: 90° Driven: YES Running direction: LINKS Engine type: SEW Eurodrive KW: 0,37/S1 Conveyor speed m / s: bitte Kontaktieren scope of delivery: without supports and side guides For individual, expert advice, simply get in to ...
Transnorm roller conveyor ejector GF 4510-1120-1000 RA1854 Make: Transnorm Roller width (RB): 1030 mm, Steel rolls Nominal/outer width (NB): 1050 mm Rolls diameter: 50 mm length: 3715mm Overall height frame: 250 ejector angle: 30° in both sides 7 rows ejector individually controllable Motor MOVI-Mot 300-500V 1,75kW Conveyor speed: freely adjustable with frequency converter Scope of delivery: with supports (please enquire if required) Prices net plus VAT. ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2016 Roll division in mm: 65 scope of delivery: including supports and side guides angle: 30° KW: 1,5/S1 Electric data: 380-500 Conveying length in mm (NL): 3715 Frame width in mm (NB): 1050 Bauhöhe in mm (BH): 250 For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you wi ...
Transnorm infeed diverter diverter inclined infeed inclined outfeed 30°-2005-1930-1000 RA1863 Exhibit Make: Transnorm Year of manufacture: 2016 Discharge angle: 30° Length: 1750 mm inclined inlet and 1130 mm with total width, total length 2880 mm and a middle length of 2005 mm Belt width (RB): 1000 mm Frame height: 150 mm Nominal/outer width (NB): 1150 mm Currently set height: 560 mm Conveying speed: with frequency converter freely adjustable V 380-500 kW 0.4-4 Overall height side wall: 200 mm Scope of delivery: motor with frequency converter, two supports, side guides, two light barriers and an emergency stop switch Features: Construction year: 2016 scope of delivery: including supports and side guides, Lichtschranken, Notausknopf angle: 30° Antrieb: SEW Getriebemotor mit MOVIMOT condition: Ausstellungsstück Belt width in mm (GuB): 1000 Electric data: 380-400 Frame width in mm (NB) ...
Belt conveyor slider 1900-300-1050 Make: Transnorm like new, showroom machine Year 2018 Length:1900 mm Belt width: 300 mm Stand dimensions: 790x480 mm Current conveyor belt height: 1050 mm Adjustable foot height: 100 mm Maximum ejection width: 890 mm Belt conveyor speed: 0,03-1,487m/s Electrical data Completely wired with sensors, direct wiring in the control box Belt conveyor motor data: V300-500, kw 0,75/S1 with frequency converter Ejection motor data: V300-500, kw 0,11-1,1/S1 with frequency converter and Brake Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany Features: Belt width in mm: 300 Conveying length in mm: 1900 Antrieb: SEW Getriebemotor mit MOVIMOT Foot plates: 790x480 Conveyor speed m / s: 0,03-1,487 Bauhöhe in mm (BH): 1050 For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be ...
TONAZZI TUBE FILLING MACHINE COLIBRI 1001 Year of manufacturing: 2003 Automatic machine for filling and sealing tubes. Used in various industries, like the cosmetic, pharmaceutical, food and chemical. CHARACTERISTICS • Ideal for small to medium and large productions • Intuitive operator interface • Includes devices to protect the operator during operation PRODUCTION • Mechanical speed: up to 100 tubes/min. • Tube Size Range (Ø): 10 ÷ 50 mm • Tube Size Range with cap (H): 50 ÷ 250 mm • Filling Capacity: 3 ÷ 390 ml • Mechanical Speed: up to 100 ENERGY CONSUMPTION • Water Consumption (for plastic or laminate tubes only): 180 l/h • Installed Power for plastic or laminate tubes: 9.2 kW • Installed Power for metal tubes: 6.7 kW • Max. Air Consumption at 5 bar (basic machine): 4000 l/h DIMENSIONS • Size (with stirrer): 2150 x 1260 x 2100 mm; Approx. ...
A total of 6 horizontal bag sealing machines Joke with vacuum and large container function are available. Seal length: 1000mm, sealing method: impulse sealing, sealing performance: 2x0.4mm, seam width: 6mm-8mm, rail opening: 30mm, throat depth: 153mm, machine dimensions X/Y/Z: approx. 1300mm/1100mm/1950mm. Documentation available. An on-site inspection is possible.
This offer is aimed exclusively at entrepreneurs within the meaning of § 14 BGB. The price is net plus 19% VAT. Welding Machine Type: Roll Seam Welding Machine Manufacturer: Nimak Type: NMP 7/100 Year of Make: 1971 Machine No. 71059 Rated power: 100 kVA at 50% ED Connected load: 175 kVA Primary voltage: 380V Open circuit voltage: 7.3V Sec. Str. dd/max. 8/33 kA Electrode force: 750 kp Frequency: 50 Hz up to 8.8 V at 6 ATU All information is made to the best of our knowledge, errors excepted. The sale is subject to exclusion of any warranty. The exclusion does not apply to claims for damages arising from grossly negligent or intentional breach of the Seller's duties or to any injury to life, limb and health. Further legal Information can be found on the website of Witzenmann GmbH under the keywords "Imprint", "Terms and Conditions" and "Data Protection".
Distance between points: 1000 mm, Height of points: 180 mm, Max. diameter to be rectified: 355 mm, Max. piece weight between points: 300 Kg, Max. weight with plate: 125 Kg, Transverse travel of the carriage (X axis): 350 mm, X-axis speed: 0.01 / 6.000 mm/min, X-axis Resolution: 0.0001 mm, X-axis measurement system: Digital ruler, Longitudinal travel of the carriage (Z axis): 1.300 mm, Z-axis speed: 0.01 / 15,000 mm/min, Z-axis resolution: 0.0001 mm, Z-axis measurement system: Digital ruler, Working wheel dimensions (od x id x width): Ø500 x Ø203 x 80 mm, Main engine power: 7,5 Kw, Angle of rotation of the grinding head: -30º / +210º, Workhead rotation speed: 10 / 800 rpm, Workpiece holder head cone: MORSE 5, tailstock cone: MORSE 4, Ø of the tailstock shank: 60 mm, Course of the counterpoint reed: 40 mm, Control type (CNC/manual): CNC, CNC brand: FAGOR, CNC model: 8040-T, Dimensions ...
2012 KRAUSS MAFFEI 850-1400-1000 MX Z Injection moldin machine missing electrical and mechanical parts Find more here - / Contact us at -
Height=1.06 m, Overall length= 0.85 m, Overall width= 0.9 m, Net weight= 150 kg,
Height=1.48 m, Overall length= 1.33 m, Overall width= 0.67 m, Net weight= 355 kg,
Height=1.2 m, Overall length= 0.95 m, Overall width= 0.8 m, Net weight= 190 kg,
Height=1.75 m, Overall length= 0.95 m, Overall width= 0.85 m, Net weight= 150 kg,
Height=1.15 m, Overall length= 0.5 m, Overall width= 0.4 m, Net weight= 180 kg,
Height=0.825 m, Overall length= 0.64 m, Overall width= 0.6 m, Net weight= 57 kg,
Height=2 m, Overall length= 0.95 m, Overall width= 1.4 m, Net weight= 270 kg,
Height=1.51 m, Overall length= 0.742 m, Overall width= 1.268 m, Net weight= 212 kg,
Height=1.1 m, Overall length= 0.9 m, Overall width= 1.2 m, Net weight= 134 kg,
Height=1.21 m, Overall length= 0.78 m, Overall width= 1 m, Net weight= 150 kg,
Height=1.235 m, Overall length= 1.003 m, Overall width= 0.856 m, Net weight= 90 kg,
Height=1.67 m, Overall length= 0.95 m, Overall width= 1.66 m, Net weight= 240 kg,
Height=1.06 m, Overall length= 1.02 m, Overall width= 0.8 m, Net weight= 165 kg,
Height=1.48 m, Overall length= 1.33 m, Overall width= 0.67 m, Net weight= 355 kg,
Height=1.85 m, Overall length= 1.08 m, Overall width= 2.05 m, Net weight= 1500 kg,
max. wheel diameter: 1250 mm gear width: 430 mm max. module: 30 min. module: 2 no. of teeth: 10 - 400 max.helical angle: 45 ° Stößelhublänge: 25 - 450 mm stroke position adjustment: 310 mm Doppelhubzahl - stufenlos: 70 - 190 U/min grinding wheel diam. min/max.: 290 - 400 mm table diameter: 1000 mm table load: 4000 kp dimensions of the machine ca.: 7,7 x 4,5 x 3,3 m total power requirement: 30 kW weight of the machine ca.: 28 t - Complete covering - Oil mist extraction - Coolant system - counter Holder - change Gears - The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Height=1.36 m, Overall length= 1.65 m, Overall width= 3 m, Net weight= 300 kg,
sheet width: 1050 mm plate thickness: 2.0 mm roll length: 1070 mm roll diam. toproll: 75.0 mm engine output: 1.5 kW weight: 325 kg range L-W-H: 1530 x 700 x 1160 mm Exhibition machine - like NEW not yet in use () Special price on request Equipment: - electro-motor-driven 3-roller round bending machine - asymmetrical roller arrangement - 2x driven rollers using a brake motor - manual folding bearing for quick removal of the workpiece - wire insertion grooves on the bottom and rear rollers - double foot switch for R/L running including emergency stop button - rear roller feed with ratchet lever - electrical safety device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1050 mm plate thickness: 2,0 mm distance between columns: 1050 mm down holder: 1 Stück fence: Tisch 80 - 480 mm fence: Breiten 0 - 600 mm table-size: 1300 x 600 mm work height max.: 760 mm total power requirement: manuell kW weight of the machine ca.: 413 kg. range L-W-H: 2,0 x 1,04 x 1,6 m - Including adjustable stop on the work table for miter cuts - The knife can be lifted easily thanks to the counterweight on the back - Large work table for safe placement of the sheet metal plates - Sheets can be pushed through, i.e. longer sheets can be cut - Handwheel on the front to adjust the back gauge - Comes with a robust cast iron base as standard - Long service life thanks to knives made of quality steel - Standard with hold-down device including quick-release clamp - Robust machine construction for high stability Furnishing: - manual lever shears - stable execution - hold-down ...
capacity 90 degrees: round: 100 mm capacity 45 degrees: round: 65,0 mm capacity 90 degrees: flat: 100 x 150 mm capacity 45 degrees: flat: 60 x 100 mm dimensions of saw-band: 1470 x 13,0 x 0,65 mm volt: 230 V : 45,0 m/min weight: 26,0 kg range L-W-H: 700 x 320 x 420 mm scope of delivery - saw band - workpiece stop - Quick release vice - Ergonomic handle - Chip collector The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
weight max. in kg: 1000 kg table width: 800 mm stroke height: 190-1010 mm table length: 1300 mm stroke of worktool slide: 40 mm/sek. weight: 220 kg Furnishing: - For ergonomic work at the optimal working height - With closed platform - Separate control unit with 3 meter cable, control buttons and emergency stop switch - Stepless lifting and lowering - Stable powder-coated steel construction - Guaranteed stability - Circumferential safety strips - Meets the safety criteria of EN 1570 - High pressure cylinder with double safety function The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
weight max. in kg: max. 1000 kg turning speeds: 0,18 - 0,58 U/min height: 976 - 1436 mm inclination: 0 - 115 ° table diameter: 895 mm voltage: 380 V total power requirement: 2,0 kW weight: 685 kg range L-W-H: 2414 x 920 x 1436 mm Exhibition machine from 2024 with only approx. 2x operating hours Condition NEW Special price on request The AK BEND SRH hydraulic welding positioner is ideal for welding, assembly and maintenance work. Positioning is done via a hydraulic rotation and tilting function. Description: - electro-hydraulic turning and tilting function - Fast handling of workpieces - Maximum productivity thanks to optimal working position - Lifting, tilting and turning workpieces in one clamping - Low idle times thanks to turning components - Maximum work performance thanks to comfortable working - Back-friendly working for the user Equipment: - Continuously variable speed adjust ...
working area L-W-H: 1000 x 900 x 900 mm range L-W-H: 1300 x 1750 x 2200 mm weight: 350 kg Description: - Compact and elegant design - Easiest operation - low material consumption - optimal use of space - highly effective dedusting - efficient way of working - Environmentally friendly working without dust nuisance - controllable material consumption - Any conventional, dry abrasive is suitable as a blasting material such as B. corundum, steel sand, glass grain, glass beads, ceramic beads The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning length: 1000 mm turning diameter: 400 mm turning dia. in gap: 560 mm spindle bore: 52,0 mm turning speeds: 45 - 2.000 U/min bed width: 210 mm spindle taper: 55029 D 1-5 taper in tailstock: 4 MK quill travel: 100 mm total power requirement: 2,0 / 2,4 kW weight of the machine ca.: 810 kg. range L-W-H: 1.890x800x1.600 mm Equipment: - 3-axis digital display i200 with LCD display - 3-jaw chuck DK11-200 mm / D5 - Faceplate 200 mm / D5, according to DIN 55029 - Fixed steady rest - passage diameter max. 90 mm - Follow-on steady rest - passage diameter max. 70 mm - Coolant system - Initial filling with Shell Tellus 46 - Extendable chip tray - Clamping disk 320 mm - Quadruple tool holder - Protective device for quadruple tool holder - Slip clutch - Micrometer longitudinal stop - Thread gauge - LED machine light - Reducing sleeve - Change gears - 2 centering points - Foot pedal with brake f ...
turning length: 1000 mm turning diameter: 380 mm turning dia. in gap: 490 mm spindle bore: 51,0 mm turning speeds: 70 - 2000 U/min bed width: 185 mm spindle taper: 55029 D 1-5 taper in tailstock: 4 MK quill travel: 120 mm total power requirement: 1,5 / 2,2 kW weight of the machine ca.: 575 kg. range L-W-H: 1920 x 800 x 1660 mm Equipment: - 3-axis digital display i200 with LCD display - 3-jaw chuck DK11-200 mm / D5 - Faceplate 200 mm / D5, according to DIN 55029 - Fixed steady rest - passage diameter max. 70 mm - Follow-on steady rest - passage diameter max. 50 mm - Coolant system - Initial filling with Shell Tellus 46 - Extendable chip tray - Clamping disc 320 mm - Quadruple tool holder - Protective device for quadruple tool holder - Slip clutch - Micrometer longitudinal stop - Thread gauge - LED machine light - Reducing sleeve - Change gears - 2 centering points - Foot pedal with brake ...
width of the strips: 100 mm band length: 2000 mm band speed: 15 + 30 m/sel tube diameter: 20 - 76 mm angle adjustable from - to: 30 - 90 Grad Dust suction hood: 2 x 75.0 mm motor speeds:: 1420 / 2660 Upm. face grinding attachment: 400 x 100 mm total power requirement: 2.5 / 3.3 kW weight of the machine ca.: 148 kg. range L-W-H: 750 x 1400 x 1200 mm Furnishing : - Constant belt tension through spring-loaded tensioning device - Standard with cylindrical grinding device - for grinding diameters of diam. 20-76 mm - Quick and easy setting of the desired grinding angle - Graphite coating on the flat grinding surface increases the sliding properties of the sanding belt - Large plan grinding surface with protective cover - Slow belt speed (15 m / sec.) - ideal for grinding stainless steel and aluminum - User-friendly tape change, quick and uncomplicated - Quick and easy changing of the grinding ...
square edge steel: 16 x 16 mm flat steel: 100 x 5 mm L-beam: 60 x 8 mm bending radius min.: 190 mm round bar steel: 18,0 mm weight of the machine ca.: 33,0 kg. Characteristics : - For precise cold and hot bending of flat, round and square steel - Stable design for screwing on the workbench - Infinitely adjustable bending stop with locking pin - With eccentric quick clamping for efficient work - Readable bending angle up to 120° - High repetition accuracy thanks to the bending angle stop - Ideal for repair shops and locksmiths Scope of delivery: - Bending plate sharp / round - Radius bending plate R 20 / R 25 - offset block - Bending plate for round bar - offset plate - Radius bending plate R 10 / R 15 - angle stop - Clamping block with eccentric clamp - Material stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1050 mm plate thickness: 1.0 mm daylight opening: 95.0 mm angle adjustable from - to: 0 - 150 Grad total power requirement: manuell weight of the machine ca.: 180 kg range L-W-H: 1320 x 790 x 1050 mm characteristics - Universally applicable bending machines for plumbing and repair shops - Simple pivoting movement of the bending beam using a bow handle - Easy adjustment of the upper beam for efficient work - High upper beam for producing high-edged profiles - The piano inserts in the upper, lower and bending beam result in a large number of bending options - Cassettes and special profiles with opposite bends are with these Models easily feasible Scope of delivery : - Segmented upper, lower and bending beam - bending segments 25 | 30 | 35 | 40 | 45 | 50 | 75 | 100 | 150 | 2 x 250 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1020 mm plate thickness: 2,5 mm daylight opening: 48 mm bending angle max.: 0 - 135 ° total power requirement: von Hand kW weight of the machine ca.: 285 kg dimensions of the machine ca.: 1,35 x 0,82 x 1,14 m Furnishing: - Universally applicable bending machine for plumbing and repair shops - Robust construction in a modern design - Easy adjustment of the upper beam using a foot pedal - Hands are free for the workpiece - Manual bending machine for standard bending tasks - Segmented upper beam for a large number of bending options - Optimal price-performance ratio - Quick and easy bending process using a bow handle - Non-slip rubber coating on the foot pedal for safe working - Easy adjustment of the lower beam to the respective sheet thickness - High upper beam for producing high-edged profiles scope of delivery - Segmented upper cheek - manual backgauge - bending segments 2 ...
sheet width: 1020 mm plate thickness: 2.5 mm daylight opening: 48.0 mm daylight opening: 150 mm ohne Segmente bending angle max.: 0 - 135 ° work height max.: 900 mm weight of the machine ca.: 340 kg dimensions of the machine ca.: 1350 x 820 x 1300 mm Furnishing: - Swivel bending machines with segm. Upper, lower and bending beam - Universally usable bending machine for sheet metal works and repair shops - Robust construction in a modern design - Easy adjustment of the upper beam using a foot pedal - Hands are free for the workpiece - Manual bending machine for standard bending tasks - Segmented upper beam for a large number of bending possibilities - Optimum price-performance ratio - Quick and easy bending process using the bow handle - Non-slip rubber covering on the foot pedal for safe working - Easy adjustment of the lower beam to the respective sheet thickness - High upper beam for t ...
sheet width: 1020 mm plate thickness: 2,0 mm daylight opening: 48 mm bending angle max.: 0 - 135 ° work height max.: 900 mm total power requirement: von Hand kW weight of the machine ca.: 285 kg dimensions of the machine ca.: 1350 x 820 x 1140 mm Furnishing: - Segmented upper and bending beam for a wide variety of bending options - Clamping by means of a foot pedal - Hands remain free for optimal positioning of the sheet - Universally applicable bending machine for plumbing and repair shops - Robust construction in a modern design - Manual bending machine for standard bending tasks - Segmented upper beam for a large number of bending options - Optimal price-performance ratio - Quick and easy bending process using a bow handle - Non-slip rubber coating on the foot pedal for safe working - Easy adjustment of the lower beam to the respective sheet thickness - High upper beam for producing ...
sheet width: 1050 mm plate thickness: 1.50 mm daylight opening: 100 mm bending angle max.: 135 ° height: OW 100 mm total power requirement: manuell weight of the machine ca.: 330 kg. dimensions of the machine ca.: 1600 x 900 x 1450 mm Equipment: - robust, manual swivel bending machine - divided upper tool - lower and rear tool Height of upper tool = 100 mm Division 100/100/100/100/100/100/100/70/60/50/40/30/100 left + right with horn tool - upper tool with quick-change system - quick foot clamp - angle stop - lockable - manual rear stop 500 mm - machine can be moved (rollers) - accessories box - rear Pictures show identical machine (UFA 1212) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning length: 1000 mm turning diameter: 360 mm turning dia. in gap: 480 mm spindle bore: 51,0 mm turning speeds: 70 - 2000 U/min bed width: 185 mm spindle taper: 55029 D 1-5 taper in tailstock: 4 MK quill travel: 110 mm total power requirement: 1,5 kW weight of the machine ca.: 540 kg. range L-W-H: 1920 x 750 x 1600 mm Equipment: - 3-axis digital display i200 with LCD display - 3-jaw chuck DK11-200 mm / D5 - Faceplate 200 mm / D5, according to DIN 55029 - Fixed steady rest - passage diameter max. 70 mm - Follow-on steady rest - passage diameter max. 50 mm - Coolant system - Initial filling with Shell Tellus 46 - Extendable chip tray - Clamping disk 320 mm - Quadruple tool holder - Protective device for quadruple tool holder - Slip clutch - Micrometer longitudinal stop - Thread gauge - LED machine light - Reducing sleeve - Change gears - 2 centering points - Foot pedal with brake functi ...
sheet width: 1070 mm plate thickness: 4.0 mm pre-bending: 3.0 mm roll length: 1070 mm roll diam. toproll: 110 mm bending speed: 3.0 m/min engine output: 2.2 kW weight: 848 kg range L-W-H: 2250 x 1000 x 1800 mm New price ~ 10.000 euros Exhibition machine - like NEW () Equipment: - robust electro-mechanical round bending machine - 2x central rollers driven by electric motor (top & bottom roller) - right/left running of the rollers - top roller can be manually swiveled out, with folding bearing - manual delivery of the side roller - including conical bending device - asymmetrical roller arrangement - rollers with profile inlets - safety device (safety line with switch unit) - 1x freely movable control panel - operating instructions (ENG) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Little-used guillotine shears, only occasionally 1.5 mm sheet thickness Stroke rate 56/ min. Power (Rm 400/mm) 3.5mm Rated power 4.0 kVA Weight 860 kg
maximum number of results exceeded
please refine your search
