bearing used for sale

Pierce control automation RUR 2500 P Work area: 2.1 m x 6.1 m Control: Burny 10 LCD Fully welded Portal construction without bolted connections o LM Guide in the transverse axis o AC servo-motors (12 000 mm / min.) o Digital synchronization on the longitudinal axis o CNC control system BURNY 10 LCD Plus with touch screen o Membrane keyboard o 'Flying' bearing inserts o Automatic initial setting of the plasma torch o Voltage monitoring of plasma torch height o 1 burner parking outside the cutting area o Circuit breaker at the end of all axes 1 x plasma Kjellberg 160i with manual gas console Cut quality cutting up to 25 mm Optional autogen retrofittable Completely Factory reconditioned machine Installation and commissioning on request

WEIBERT WJ-D53 Thickness Planers WEIBERT WJ D53 NEUMASCHINE! 400V 5,5 KW (7,5 HP) n = 5000 RPM Planing width 530 mm Max.Spanabnahme 8 mm Planer shaft D = 125mm 4 turn blade shaft Clearance height from 3 to 300 mm Feed speed of 8 and 16 m / min. Feed motor 1.5 KW (2 HP) Dust nozzle by 160 mm Electronic height adjustment of the Thicknesser table with display Machine table, Planer shaft bearing block and table management from GRAUGUÃ?! G & WJ-D53

FOR SALE STANDARD SIZE MEASURMENT CRANKSHAFT OF MAK 6M 332AK TO WHOM AT MAY CONCERN; THE CRANKSHAFT HAD BEEN PUT ON V BLOCK AND FOLLOWING TESTS HAD BEEN CARRIED OUT. -Main and crankpin journals measurements had been carried out. -MPI test had been carried out and no. crack had been observed. Crankshaft were found typical. -Run-out measurement had been carried out found in good order. -Hardness test had been carried out to all crankpins and main bearing journal. All values had been found in permissible limits. -Crankshaft had been polished. CRANK SHAFT READY TO TRANSPORT AT IZMIR - TURKEY. WITH FULL SEVICE REPORT IF YOU'VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba Best regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 .aliagamarine.com TURKEY ...

unused counter-holder for horizontal fraesening for WMW FQ400CNC The gnholder has a counter bearing for the reception of the long fraesdorne. Special price

Bearing platform 4,000 x 15,000 mm, load capacity 500 kg / m2 Included in the scope of delivery are: 4 stands, one side 100 x 100 x 3 mm 4 stands, double-sided 100 x 100 x 3 mm 6Main carrier C+300 x 3 x 4,190 mm 15 cross member S+300 x 2 x 4,800 mm 30 Mounting angle 4 Cross Associations 27 chipboard P6, 3000 x 850 x 38 mm, UK white, OK natural UK white, OK nature incl. fastening material incl. load signs Dimensions, technical data Steel construction: 4,000 x 15,000 mm Floor area: approx. 60 sqm Height top edge floor covering: up to 3,500 mm freely selectable ( other heights on request ) light height underside: OK minus 338 mm Capacity: 500 kg / m2 Columns: 100 x 100 x 3 mm Main carrier: C-Profile C+300 x 3 mm Cross member: Sigma profiles S+300 x 2 mm Flooring: 38 mm chipboard, white on one side Columns in the following standard colors: Ral 7035,  ...

Bearing platform 8,000 x 5,000 mm, load capacity 500 kg / m2 Dimensions / technical data Dimensions steel construction: 8,000 x 5,000 mm Dimensions floor area: 8,000 x 5,000 mm Floor area: approx. 40 m2 Height OK floor ingesis: up to 3,500 mm (freely selectable) light height underside: Ok minus 338 mm net load capacity: 500 kg / m2 same-distributed load Included in the scope of delivery are: 6 steel tube supports 100 x 100 x 3 mm 4 main beams C+300 x 3 x 3,990 mm (perforated) 9 cross beams S+300 x 2 x 4,800 mm (closed) 18 Mounting angle 3 Cross Associations 18 chipboard P6, 3000 x 850 x 38 mm, UK white, OK natural incl. fastening material incl. load signs Stand optionally in the following standard colours: Ral 7035, light grey Ral 7016, anthracite grey Ral 3000, red, fire Ral 5003, sapphire blue (Other colors on request!) Main and cross beams galvani ...

Bearing platform 12,000 x 5,000 mm, load capacity 500 kg / m2 Dimensions / technical data: Dimensions steel construction: 12,000 x 5,000 mm Dimensions floor area: 12,000 x 5,000 mm Floor area: approx. 60 m2 Height OK floor ingesis: up to 3,500 mm (freely selectable) light height underside: OK minus 338 mm net load capacity: 500 kg / m2 same-distributed load Included in the scope of delivery are: 8 stand, one side 100 x 100 x 3 mm 6 main beam C+300 x 3 mm, L = 3,990 mm (perforated) 13 cross member S+300 x 2 mm, L = 4,800 mm (closed) 26 Mounting angle 3 Cross Associations 24 chipboard P6, 3000 x 850 x 38 mm, UK white, OK natural incl. fastening material incl. load signs Stand optionally in the following standard colours: Ral 7035 light grey Ral 7016 anthracite grey Ral 3000 fire red Ral 5003 sapphire blue (other colors on request) Main and cross bea ...

Bearing platform 16,000 x 5,000 mm, load capacity 500 kg / m2 Dimensions / technical data Dimensions steel construction: 16,000 x 5,000 mm Dimensions floor area max.: 16,000 x 5,000 mm Floor area: approx. 80 m2 Height OK floor ingesis: up to 3,500 mm (freely selectable) light height underside: OK minus 338 mm net load capacity: 500 kg / m2 same-distributed load Included in the scope of delivery are: 10 stand, one side 100 x 100 x 3 mm 8 main beam C+300 x 3 mm, L = 3,990 mm 18 cross member S+300 x 2 mm, L = 4,800 mm 36 Mounting angle 4 Cross Associations 33 chipboard P6, 3000 x 850 x 38 mm, UK white, OK natural incl. fastening material incl. load signs Stand optionally in the following standard colours: Ral 7035 light grey Ral 7016 anthracite grey Ral 3000, red, fire Ral 5003 sapphire blue (other colors on request) Main and cross beams galvanized  ...

Control SIEMENS 805 TECHNICAL DATA: WORK AREA / DIMENSIONS Swing over bed [mm] 820 Swing over facing slide [mm] 515 Displacement of the plan slide [mm] 520 Displacement of the upper support [mm] 250 Turning length [mm] 2000 Tip height on flat railway [mm] 400 Bed width [mm] 560 Bed sleigh length [mm] 800 Facing slide width [mm] 320 Plan valve length [mm] 1005 Upper support width [mm] 200 Turning tool cross section according to DIN 770 hxb [mm] 40 x 25 MAIN SPINDLE Spindle nose according to DIN 55 027 [Gr.] 11 Spindle diameter in front bearing [mm] 170 Spindle bore [mm] 128 Inner taper of main spindle [metr.] 136 MAIN drive infinitely adjustable three-phase motor (AC motor) Power 60% / 100% ED [kW] 46/37 Torque max 60% / 100% ED [NM] 5,300/4.260 Torque max 60% / 100% ED [NM] 5,300/4.260 Total speed range [min-1] 6.3 1,600 Transmission levels 2 Speed rang ...

with 60 rinsing stations, 80 filling valves and 14 head screw capper Capacity: 2.0 l dia 99.8 x H= 350.00 mm - capacity: 7,000 bph 1.0 l dia 81.37 x H= 276.17 mm - capacity: 14,000 bph 0.6 l dia 68.0 x H= 245.16 mm - capacity: 20,000 bph The filler and rinser will be completely dismantled. All gear wheels on the filler are brand new. So the main bearing will be renewed. The filling valves will be complete renewed into new generation neck holding filling valves. The product inlet pipe will be renewed. All types will be renewed. So the Alcoa screw capper will be complete dismantled and modified, with a pick in place system to handle 28mm plastic screw caps. The AVE rinser will also be complete dismantled and rebuild from the beginning. The filling valves of the filler are neck holding filling valves so the filler does not have lifting cylinders anymore. The complete bottle tra ...

10 pcs. crane runway length approx. 9.5m long HEA 200/190 (s=6 mm) Crane rails 40 x 40 mm Accessories Available on request at an additional cost: - Circuit rail VAHLE Assembly On request, installation/assembly/recommissioning, also constructive changes (wingspan, hoisting unit, etc.), can of course be carried out by us in accordance with relevant regulations or with acceptance(s) throughout Europe. Visit A visit is possible at any time and at short notice, whereby the crane can also be tested under electricity if necessary. to ask? Further details, photos, descriptions and appointments for the visit can be arranged at: Phone: +49 - (0)8654 / 77669-0 e-mail: info.torlach EXPORT / SHIPPING / MONTAGE We have 20 years of experience in the worldwide export of plants and machines. - 6,500m2 bearing with track connection and container loading ! - O ...

Bearing number: 3421 CNC LATHE Manufacturer: Haas, Type: TL 25HE Machinen NR.: 70403, built: 2005 Specifications: Max. turn. about 760 mm dia. Max circulation diameter 405 mm dia. Turning length 860 mm Spindle bore 70 mm dia. Main spindle speed range 3400 rpm C Axis - Main spindle movement 0.001 degrees Main motor power 22 kw Tool turret with 12 stations Counter-spindle Counter spindle speeds 4000 Pr/min Operating hours Spindle 9750 hours Accessories: collet device. Materials feed 65 mm Parts Catcher Cooling water system. Chip promotion. Various accessories. Length: 2000mm, Height: , Width: 2100mm, Weight: 8000 Kg

UTS Separator FSP B-78/15 Bedding-Technical Data Sheet Dimensions/Weight: length mm 2743 width mm 711 Height mm 980 Weight (empty) kg 770 Weight (in operation) kg approx. 850 Schnecke: Material Stainless St./tungsten Carbide Coating Length of auger mm 1160 Active length mm 1099 Screens: Pitch mm 200 Material stainless steel Helix diameter mm 260 length filter screen F mm 520 Helix thickness mm 10 length filter screen FXX mm 260 Number of Helixes 2 length press screen mm 150 Inlet Housing: Diameter screens mm 260 Material Spheroidal cast iron EN-GJS-400-15 screen surface area m2 0.72 Diameter inlet pipe connection mm 100/102 Drive adapter: Dimens. Maintenance opening mm 160 x 220 Material St. Steel/housing Mild steel painted Screen Housing: Bearing 2 taper roller bearings Material Spheroidal cast iron EN-GJS-400-15 sealing system mechanical seal, grease Chamber Lengt ...

Mitsubishi engine L3E, 3-cyl. water cooled, 952 CC displacement, engine without a flywheel, connecting rod bearing defective.

Tyre Packing Machine, Tyre Tripling Machine BTS-Tyre Packing Machine The BTS-Tyre Packing Machine was designed for specialized Tyre trading companies. It is the perfect solution for cost-effective second hand tyre business. The Tyre Packing Machine solves space, storage and transport problems. It is easy to pack 2 and more used Tyres into one. Doubling or tripling creates a huge reduction of volume, benefit is more storage and loading space so transport and allowable weight that can be exploited efficient. - Extreme solid and brass mounted packing slider with grease nipples - Robust and long-life design - High performance cylinder - Ball-bearing roller guides - Adjustable work height - Pneumatic quick connectors - Extremely quiet due to silencer - CE-certified - Quality product Made in Germany Pressing force: 0.125 Ton Power supply: Air, up to 10 bar / 145 psi Machine ...

Tyre Packing Machine, Tyre Tripling Machine BTS-Tyre Packing Machine The BTS-Tyre Packing Machine was designed for specialized Tyre trading companies. It is the perfect solution for cost-effective second hand tyre business. The Tyre Packing Machine solves space, storage and transport problems. It is easy to pack 2 and more used Tyres into one. Doubling or tripling creates a huge reduction of volume, benefit is more storage and loading space so transport and allowable weight that can be exploited efficient. - Extreme solid and brass mounted packing slider with grease nipples - Robust and long-life design - High performance cylinder - Ball-bearing roller guides - Adjustable work height - Pneumatic quick connectors - Extremely quiet due to silencer - CE-certified - Quality product Made in Germany Pressing force: 0.125 Ton Power supply: Air, up to 10 bar / 145 psi Machine ...

CNC laser cutting machine Bystronic Bystar 3015 -. Overall performance 125 KVA Co ² laser source of Bylaser power 5200 Watt,. CNC rotary axis for Chuck Ø 315 mm with thrust bearing for tube processing Cutting performance ST37 - approx. 25 mm Stainless steel 1.4301 approx. 20 mm, aluminium approx. 12 mm Cutting speed maximum 50 m/min, simultaneous positioning up to 113 m / min car. Bela de Setup Byloader with sheet metal separation Dedusting equipment Only dividers operation! CA. 27.500 power-on hours -. approx. 6000 hrs laser hours

Precision lathe with cycle automatic Make: Hamlet Model: E 70 x 2000 Year of construction: 1997 For food and feed shaft machining Technical data: Workspace Turning length: 2000 mm Swing over bed: 720 mm Swing over cross slide plan: 430 mm Displacement of the plan slide: 410 mm Bed width: 480 mm 3prpek3uq Spindle nose ACC. to DIN 55027: size 11 Spindle diameter in front bearing: 150 mm Spindle bore: 106 mm Inside taper of the main spindle: 112 metric Control: Siemens 805 Spindle gearbox newly stored according to the manufacturer ca. 2.500 EUR

Spreader pad width 1810 mm ex miner dung-and compost spreaders M 92 SG,. with 2 scatter shaft diameter approx. 520 mm. used part, bearing i.O. More parts available. -Jacobis local, environmental & green care technology- Pre-owned equipment & sports square care, garden & landscape construction, cemetery technology & winter maintenance, reversing operations & decommissioning, environmental care, motors and more...

High-performance band sawing machine for cutting pipes and round material in multi-channel process with symmetrical material supply and discharge on both sides Manufacturer ZS-Technology Meissen Type MKS 6/2 Built in 1998 - 9 two-sided assignable pipe ducts - max pipe length 8,000 mm - Cycle time approx. 90 sec. / Stroke=5 sec. / pc. - max. section length 100 mm - Diameter 20 - 100 mm Materials Structural steels, C-steels, low-alloy steels, rolling bearing steel (especially 100Cr6) Pipe dimensions / pipe sections - Pipe outside 25 - 128 mm - Pipe wall thickness 3.2 - 16 mm - Pipe length 6,000 mm Required footprint for all components 7,000 x 16,200 mm Search terms: band saw machine, multi-channel band saw, backdrop band saw, high-performance band saw machine

Cooling cabinet from Hauser, ready to plug - 130 cm wide - with integrated refrigeration unit, refrigerant R404A - with built-in magazine or bearing

RECON Part number: 1216 1230 Main bearing standard dimensions New camshaft bearings ---------------------------------------------------------------------- ------- Please note: we also have other various RECON parts of different manufacturers / types in stock. We are pleased to provide you with our current stock list. If you have any further questions do not hesitate to contact us

specifications: Max sheet width 3,000 mm Max sheet thickness at max yield strength 240 N/mm2 when bending to max. sheet width 35 mm when rounding Bend length 2.2 x S Max passage between rollers 145 mm Roller diameter upper roller 552 mm Underroller 532.4 mm Side rollers 400 mm Number of rollers 4 Powered rollers 2 top and bottom roller Drive of the rollers hydraulically Arrangement of the rollers symmetrically Rotation speed of the rollers 2-4 m/min Adjustable rollers 3 Type of adjustment of the rollers hydraulically Adjustment speed lower roller 0-200 mm/min. Side rollers 0-700 mm/min. Brake of the rollers pneumatic Actuation of the folding bearing hydraulically Operating voltage 3 x 380 V / 50 Hz Display device of the roll positions 4 x optical/analog Weight of the machine approx. 42 to Area 2.71 x 6.4 m Height 3.12 m

Description mobile height-adjustable Gura scissor roller conveyor 1200-425 2KUX from year 2009 Scissor roller conveyors are used in all areas of general cargo transport in operation. Especially when a permanently mounted system is not desired, this mobile variant is used. Own logistics structures can thus be optimally adapted and expanded as desired. The tracks are individually adjustable in length and height, at the same time curves up to 180 can be formed. – gloss-galvanized version – web top edge from 720 – 1150 mm height-adjustable. – For conveyed goods up to 425 mm – Axle distance with extended web 150 mm. – Rollers ( 50 mm) ball bearing on 8 mm axes – End stop at the end of the roll Number of support feet 3 pieces (+one extension) Web length 1600 – 5500 mm Load capacity/support foot distance 100 kg Roll material Plastic Rolls per axle 2 pieces Roller design Plastic

Swing boom crane boom crane with ZYBA-MAT Manufacturer: Strödter Type: ZP 60 / SAZ 60 D1 Built: 2014 New and unused Load capacity permissible load weight max: 25 kg Working radius approx.: 3,000 mm Stroke max: 800 mm Lifting speed max. : approx. 800mm/sec. Energy supply: pneumatic Mounting: Swing boom with stand column Net weight device (with load-carrying equipment): 287 kg Pneumatic working pressure: 6 bar Air quality required for maximum load-bearing capacity: clean, dry and filtered (5 microns) Air consumption max.: approx. 17 Nl/ double stroke ZYBA-MAT on the swivel boom Pneumatic balancing control with automatic scale

Set of 2 unused Duechting type MC 50-315 D pumps, manufactured in 2014. Düchting Pumpen Maschinenfabrik GmbH & Co. KG Q 20 m³/h H 21.8 m N 1140 1/min P 4.1 kW T 70 °C Rho 1400 kg/m³ TYPE MC Horizontal single-stage centrifugal pump in back pullout design. • Pumping of abrasive and corrosive liquids • All components which are in contact with the liquid are made of SICcast • Suction flange: Axial • Discharge flange: Top (Vertical) • Closed impeller with three-dimensionally curved vanes • Impeller is key driven; reverse rotation (e.g. back-flushing) is possible • Re-adjustable inclined gap between impeller and volute casing to optimize the efficiency and differential pressure after longer operation • Single acting, metal free mechanical seal DÜTEC with springs located outside of the liquid (other seal types available) • Oil-lubricated antifriction  ...

A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant Refurbished Pharmapaktor APC L200/50. The machine was previously used as a demo and rental unit. Compacting head Two cast stainless steel H-frames connected by spacer bolts. Two laterally foldable swing arms for easy and quick changing of the rollers. The swing arms are fixed with two tie rods, which also absorb the compressive forces of the compacting rollers. One chamber insert for guiding the product flow and two center pieces for sealing the roll ...

-Peak height 240mm -Peak width 1000mm -Control Siemens -Circular permes.about bed 490mm -Umlaufdurchmes.ü.Planschlitten 195mm -Crumpling 520mm -Spindeldurchmes.im in front. Bearing 100mm -Spindle bore 63mm -Torque 736Nm

TECHNICAL DATA: Working range: 2,500 x 1,250 x 115 mm Control: Siemens Sinumerik 840 D Laser power: 2,000 watts Max sheet thickness structural steel: 20 mm Max sheet thickness stainless steel: 12 mm Max sheet thickness Aluminium: 8 mm STANDARD EQUIPMENT: â?¢ Closed machine frame with integrated laser unit â?¢ TRUMPF laser TLF 2000 â?¢ Laser unit: CO2 laser, high-frequency excited, cooling unit, logbook function â?¢ Automatic pallet changer and laengsfoerder tape â?¢ Drives: maintenance-free three-phase servo motors â?¢ Laser power control â?¢ HI-LAS high-pressure cutting â?¢ Plasma sensors PMS â?¢ Fast processing with SprintLas â?¢ ContourLas for the production of small loechers â?¢ Cutting gas pressure adjustment programmable â?¢ La ...

Bearing number 1105-02690 Machine type Milling machine - Universal Make HERMLE Type UWF 1000 Built in 1988 Control type CNC Storage location FRANCE Country of origin Germany Delivery time SOFORT Freight base EXW Technical details x-way 700 mm y-way 630 mm z-way 500 mm Control heidenhain 355 Tool holder SK 40 (DIN 69871) Table clamping area: 1000 x 490 mm Spindle speed Gear stage 1 25 - 400 rpm. Spindle speed Gear stage 2 401 - 1260 rpm Spindle speed Gear stage 3 1261 - 4200 rpm Feed 5 m/min Rapid speed 10 m/min Swivel of the milling head + / - 90 ° Pinole diameter 110 mm Pinole stroke 95 mm Total power requirement 18 kW Machine weight approx. 5 t Information with full cabin coolant device Sale takes place without clamping equipment approx. 8500h switch-on hours

For sale a milling head without counter bearing

Technical data: Fixed angular table: Fixed angular table clamping area: 800 x 400 mm Max table load: 200 kg Working spindle: Tool holder horizontally and vertically: ISO 40 Power of the main drive motor / 100% ED: 2.2 kW Vertical milling head: Speed range, tiered: (12) 50 - 2000 rpm Drill pinole, stroke: 100 mm Swivel range: +/- 90° Travel: X-axis automatic/man.: 385/400 mm Y-axis automatic/man.: 185/200 mm Z-axis automatic/man.: 365/380 mm Feeds: Feed range: 0-650 mm/min Number of feeds: infinitely adjustable Rapid response: 1000 mm/min Characteristics: - Machine accuracy according to DIN 8615 - 3-axis digital displays FAGOR® Innova (option) - Spindle run max. 0.005 mm, incl. test protocol according to DIN 8615 (rolling bearing SKF®/NSK®) - Vertical milling head can be swivelled out for horizontal milling (without d ...

Ladies and gentlemen, below we offer the following machine for sale: from a tool making, single-layer run and very well maintained. Still under power. CNC lathe Voest - Alpin - Weipert WNE 490 X 1000, peak height 240mm, tip width 1000mm, control Siemens, circulating through mes.over bed 490mm, circulating permes.via plan slide 195mm, crimping 520mm, Spindeldurchmes.im front. Bearing 100mm, spindle bore 63mm, torque 736Nm.

Two-coordinate measuring instruments ZKM Applications: External measurements - Internal measurements - Bore distance measurements with double image eyepiece Shape tests with reable inserts Angle measurements with angle measurement slot and optical rotary table (2") Male thread measurements Equipment: Spitzenbock - Angle measuring device to the tip trestle (5") - adjustable V-bearing opt.-mechanical probe (measuring lever attachment) - adjustable plant table - incident light illumination Projection device - Rotary table with partial circle Increased optical touch accuracy through the use of inteference lines ZKM 01-150 Measuring range x - 150 mm Measuring range y - 100 mm Scale value 0.1 mm ZKM 01-250 Measuring range x - 250 mm Measuring range y - 100 mm Scale value 0.1 mm possible versions:  ...

Key data: 500 , 520 , 380

Bearing number 1105-02750 Machine Type Machining Center - Universal Make DMG DECKEL-MAHO Type DMU 50 eV / 5 axes Built in 2001 Control type CNC Storage location FRANCE Country of origin Germany Delivery time immediately Freight base EX WORK Technical details x-way 500 mm y-way 420 mm z-way 380 mm Control HEIDENHAIN TNC 430 Spindle cone SK 40 Speeds 18,000 rpm Spindle motor 15 kW Rapid speed 50 m/min Table clamping area 500 per m. x 380 mm Feed range up to 20 000 mm/min Tool change device 32 fold Total power requirement 38 kVA Machine weight approx. 5.9 t Information - CNC - CONTROL of the display of HEIDENHAIN TNC 430 - 5-axis machine with B + C axis - Spindle on: 22 800 h - Current on: 38 000 h - Machine documents spaenefoerderer

1 x Universall tool-feeding machine Lid FP 4 Built: c.1970 Very robust and rare conventional machine in good condition. Technical data: Travel: X: 700 Y: 400 Z: 450 mm Spindle speeds: 31.5 - 1,600 rpm (18 levels) Tool holder: ISO 40 Pinole stroke: 115 mm Feed in X/Y/Z Feed range: X/Y/Z 5 - 500 mm/min (infinitely adjustable) Rapid response: X/Y: 10 - 500 mm/min Z: 5 -250 mm/min (18 levels) swivel handling table Clamping area: 860 x 500 mm Accessories: 1 x horizontal counter bearing 5 x horizontal frond spine Bftj7cazem 10 x vertical fraes aufnahme 36 x tension tension ingesheis from 0.5 - 18 mm 0.5 mm rising 5 x Direct clamping pliers D: 12/14/16/18/20 mm 1 x machine vice Manual various distance rings and accessories for milling machines complete documentation The machine can be inspected at our warehouse under electricity. A 3-axis digital ...

Two-coordinate measuring instruments ZKM Applications: External measurements - Internal measurements - Bore distance measurements with double image eyepiece Shape tests with reable inserts Angle measurements with angle measurement slot and optical rotary table (2") Male thread measurements Equipment: Spitzenbock - Angle measuring device to the tip trestle (5") - adjustable V-bearing opt.-mechanical probe (measuring lever attachment) - adjustable plant table - incident light illumination Projection device - Rotary table with partial circle Increased optical touch accuracy through the use of inteference lines ZKM 01-150 Measuring range x - 150 mm Measuring range y - 100 mm Scale value 0.1 mm ZKM 01-250 Measuring range x - 250 mm Measuring range y - 100 mm Scale value 0.1 mm possible versions:  ...

ELHA 6 Axis Horizontal Machining Center Xpert-K High-Performance Horizontal Machining Center The newly designed DEPO XPERT K horizontal machining centre offers a high degree of flexibility and above-average productivity. Description Horizontal BAZ The 6 axes are individually controllable. The HSK 100 holder makes it possible to clamp large tools and thus process large areas with high chip removal. Installed is a high-performance G30 fork head spindle with hydromechanical clamping system and a hybrid slewing bearing at top speed which allows extremely high speeds to be driven in order to achieve an optimal milling result even with the smallest tools. This fork head is equipped with a fully automated spindle change cycle, which makes it possible to replace the complete spindle in less than an hour. A hydraulic clamping device is installed for clamping components (effective table ...

NuÃ?müller Fast V-belt discs mixed lot: 4 pcs. V-belt washers equivalent Fig. for sale, all unused with bearing tracks. Shipping possible, offers requested. ------ Jodau Municipal, Environmental & Green Care Technology ------- Used machines for plant & sports field maintenance, gardening & landscaping, cemetery technology & winter service, sweeping & disposal, environmental care, motors and more...

USED COMTEIFA FT-12 BG CENTRIFUGE REF#: C5613 Used vertical axis basket centrifuge with upper discharge with filtering bag mounted on three feet (with compression straps and springs). Type FT-12-BG manufactured by COMTEIFA. AISI 316 SS wetted parts. General characteristics: Manufactured by COMTEIFA Model FT-12-BG Type Vertical basket top discharge centrifuge Material Stainless steel 316L Variable speed by frequency converter. Total opening All parts in contact with the product are made of AISI 316L stainless steel. Mounting on very strongly sized roller bearings. Bearing house of cast iron. Electric stop brake made by the converter. AISI 316L stainless steel lid with spring-compensated piston movement Technical characteristics: Download Manual above with bag Basket diameter 1,200 mm Height basket 650 mm Max. load 450 kg Useful load 350 dm3 Max. rotationa ...

Bearing number: 3488 Profile steel shears Manufacturer: Mubea, Type: KBLH 500 Machines NR.: 0156085927332, Year of construction: 0 Specifications: Size Printl 50 To Max punching dia 30 x 15 mm mm Stroke length 0-60 mm Number of strokes per min. 16 Extension 410 mm Flat steel 180 x 20 - 400 x 10 mm Angular steel 50 mm Round steel 55 mm Total power 7.5 kW Hydraulic. Length: 1400 mm, Height: 1800 mm, Width: 800 mm, Weight: 1800 kg

Capacity round maximum diameter: 0 mm Angle degrees maximum: 0 Capacity square: 0 mm Workpiece height: 0 mm Workpiece width: 0 mm Capacity rectangle: 0 mm Operating hours: 54112 Technical data Cut range: round up to: 10 - 260 mm Square: 260 x 260 mm vertical hydraulic Automatic Cut length: min.: 5 mm max: 680 mm Max. automatic forward feed length: 680 mm stepless from: 15 m/min up to: 125 m/min Band length: 4115 mm Band width: 41 mm Sheet thickness: 1.3 mm Voltage 50 Hz 3x: 380 Volt Power: 4 / 6.5 kW Machine´s weight about: 1915 kg Overall dimensions machine: Length: 2125 mm Width: 1930 mm Height: 2100 mm Various accessories: Automatic forward feed Material bearing lenght: 1 m Roller conveyor Coolant system Chip conveyor

Capacity round maximum diameter: 0 mm Angle degrees maximum: 0 Feeding length automatic feeder: 0 mm Diameter sawing blade: 0 mm Technical data Execution: semi-automatic Swivelling range: +/- 90 ° Saw blade diameter: 300 mm Max. saw blade diameter: 315 mm Cut range: round max. tube: 100 mm Max. automatic advance length: 500 mm Voltage 50 Hz 3x: 380 Volt Power: 4.33 HP Machine´s weight about: 650 kg Overall dimensions machine: Length: 1500 mm Width: 800 mm Height: 1700 mm Various accessories: Automatic forward feed Coolant system Material bearing lenght: 3200 m Machine base

Used storage heater Manufacturer Seipp Type UAGG 390- heats workpieces and ball bearings up to XXX kg With various yokes in different sizes Workbench model with swivel arm Applications: Chemical industry, steel industry, paper industry, transmission manufacturer, mechanical engineering, transport sector Voltage / Frequency / Power: 380 V / 50Hz / 35A Properties: When warming in a horizontal position, the maximum effect is achieved. Workpiece: Weight bearing max. xxx kg (other workpieces xx kg) Inner diameter 15/120 mm Outer diametermax. xxx mm Width max. xxx mm Automatic temperature: Magnetic sensor, control range 60 °C to max. 160 °C Aperture priority: Bays: Edge length 80mm, 70mm, 60mm, 40mm, 30mm, 20mm, 15mm - Induction heater - induction heater Special price

Hydraulic mobile tin hole punch for e.g. control cabinet construction and control construction Manufacturer Alfra Type SKP-1 Punches holes of max 140mm diameter in 3mm sheet metal Round, square and rectangular stamps possible. Punch punch punch tin punch drill tin hole drill monocut gap-plate-hole, hand hydraulics, ball bearing screw, Klauke Alfra Special price

Planscheibein little used condition Manufacturer TG Diameter approx.610mm Body bearing traces (can be easily removed!) Short cone chuck flange for spindle heads DIN 55027 or ISO 702/III (same as old standard DIN 55022) with stand-up bolt and nut nuts. Short cone holder size 8 for bayonet closure Cone-d2 139.735 mm Röhm Bilsing Werner Garant Toss Forkart Schunk rotary lining röhm rotary lining baking rotary lining manufacturer camlock rotary lining baking lining rotary foe flange forda rotary lining rotary lining adapter flange Special price

Planscheibein little used condition Manufacturer TG Diameter approx.500mm Body bearing traces (can be easily removed!) Through hole, approx. 90 mm Short cone chuck flange for spindle heads DIN 55027 or ISO 702/III (same as old standard DIN 55022) with stand-up bolt and nut nuts. Short cone holder size 8 for bayonet closure Cone-d2 139.735 mm Röhm Bilsing Werner Garant Toss Forkart Schunk rotary lining röhm rotary lining baking rotary lining manufacturer camlock rotary lining baking lining rotary foe flange forda rotary lining rotary lining adapter flange Special price

Pester PEWO pack 250 compact HS and Therm 250 - Balcony construction with free access to the work area Film storage - Thorn bearing with pneumatically opening spring pressure brake Closing unit Closing unit -Closing beam driven by servo motor and crank drive Sealing unit - low-wear sealing system thanks to steel sealing beams with precise temperature monitoring Plant features: - Operating side on the right - Lauer PCS control panel (standard) - Standard cladding in acrylic glass - Machine design degree of protection IP54 - Control cabinet for pack Compact - Voltage 3x400V+N+PE, 50 Hz/60 Hz - Control Elau PacDrive MAX-4 - Traffic light display in three-colour standard version - Electric standard version - Pneumaticstandard version - Pluggable proximity switch IFM (standard) - Model PEWO-therm III 250 mounted in line - For thermal side shrinkage ...

Machine details Bearing number 1105-03038 Machine type Machining Center - Vertical Make CHIRON Type FZ12 WM Built in 1997 Control type CNC Warehouse FRANCE Country of origin Germany Delivery time immediately Freight base freely loaded from location Technical details x-path 550 mm y-path 300 mm z-way 425 mm Tool holder SK 40 Control Siemens 810 Total power requirement 12 KVA Machine weight approx. 4.0 t Transport dimensions LxWxH 2.05x3.05x3.0 m Information Machine is located in the technical GOOD CONDITION with interchangeable plate 2 X 4th axis PEISELET PT 160 WITH SIEMENS 810 WITH HYDROLIC CLAMPING IN THE TABLE 24 FACH WERCKZEUGWECHSLER

Machine details Bearing number 1105-03062 Machine type Machining center - Horizontal Make MAZAK Type FH 680 Built in 1997 Control type CNC Warehouse FRANCE Country of origin Japan Delivery time immediately Freight base from location Technical details x-way 1050 mm y-path 800 mm z-way 880 mm Control MAZATROL M plus Pallet changer type 2-fold Pallet size 630 x 630 mm Tool changedevice 40 Tool holder bt 40 Table load 1 t Pallet change time 6 sec Rapid response 40 m/min Feed 1-40,000 mm/min Speed 35-7000 rpm Drive power 30 kW Workpiece dimensions max. 1000X 1000 mm Tool diameter 135/260 mm Tool length - max. 500 mm Tool weight max. 7 kg Total power requirement 45 kVA Machine weight approx. 15 t Space requirement approx. 19 m2 Information High-pressure cooling by spindle 20 bar MAZATROL m plus Synchronous thread cutting NC Round table 0.001° x 360,000 p ...