be used for sale

I-beam section - upend: 100 x 20 (d 2100) mm tube diameter max.: 100 x 3 (d 3000) mm L-beam: 80 x 80 x 8 (d 2000) mm square material: 50 x 25 x 2 (d 600) mm bar material - diameter: 60,0 (d 1000) mm I-beam section - flat steel: 120 x 30 (d 600) max. 140 mm tool taper: 80,0 turning speeds: 4,2 U/min weight: 1600 kg dimensions: 1240 x 1375 x 1540 mm Domestic equipments: - Welded steel structure (St-52) - Rollers are driven by 3 separate hydraulic motors - Stepless speed - Special steel gears - Shafts are made of special steel, hardened and ground - Manual lubrication - Guide rollers are hydraulically adjustable - Lower rollers are hydraulically movable up and down - Infinitely adjustable speed of the lower rollers, move after below and above - Digital display for lower rollers - Separate and movable control panel - Horizontal and vertical operation - Production quality certified according  ...

I-beam section - flat steel: 80x20 (d1200) mm I-beam section - upend: 80x25 (d2100) mm L-beam: 50x50x6 (d1000) mm bar material - diameter: 40 (d800) mm square material: 60x60x3 (d4000) mm rectangle: 80x30x3 (d6000) mm tube diameter max.: 70x2 (d1600) mm tool adaptor: 60 mm roll diameter: 177 mm bending speed: 6,4 m/min total power requirement: 4 kW machine weight ab.: 970 kg Overall size: 1400x950x1450 mm Domestic equipments: - hydr. roller drive - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1300 mm table load: 7.000 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 0,9 UpM T-slots: 6 x M24 Tilt Angle: 90-180-100 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 3.050 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

L-beam: 50x5 mm square material: 50x40x3 mm I - beam section - flat steel: 120x15 mm I-beam section - upend: 60x10 mm round material: Ø 35 mm tube diameter: Ø 70x2 mm roll diameter: 155 mm Shaft diameter: 50 mm bending speed: 4,3 m/min total power requirement: 1,5 kW weight: 400 kg dimensions: 830x730x1350 mm Domestic equipments: - Extended special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

round material: 40 mm tube diameter: 70x2 mm square material: 80x30x3 mm L-beam: 50 x 5 mm I - beam section - flat steel: 80 x 16 mm roll diameter: 157 mm I-beam section - upend: 50 x 15 mm Shaft diameter: 50 mm bending speed: 2,95 m/min total power requirement: 1,1 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: 1000x950x1450 mm Domestic equipments: - Special steel shafts (42CrMo4) hardened and ground - a set of standard rollers - lower rollers up and down hydraulically deliverable - digital display for lower rollers - separate control panel - in one direction manually adjustable lateral straightening rollers - manual lubrication - horizontal and vertical operation - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 4 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 132 mm tool adaptor: 40 mm speed: 5 m/min total power requirement: 2,2 kW weight of the machine ca.: 350 kg dimensions of the machine ca.: 1650x700x1280 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 715 mm table load: 500 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 1 UpM T-slots: 6 x M16 Tilt Angle: 90-180-110 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 675 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

saw blade diameter: 370 mm capacity 90 degrees: flat: 200x100 mm capacity 90 degrees: round: 130 mm : 34/68 UpM total power requirement: 2,6 kW height of material-table: 900 mm dimensions of the machine ca.: 1335x865x2175 m weight of the machine ca.: 430 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

arm length: 350-1590 mm bore capacity in steel (diameter): 50 mm spindle taper: MK5 threading: M42 quill stroke: 320 mm total power requirement: 4 kW workpiece height max.: 645-1240 mm range L-W-H: 2450x980x2840 mm turning speeds: 25-2000 U/min Total weight, approx.: 3500 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 960 mm table load: 3.500 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 0,9 UpM T-slots: 6 x M20 Tilt Angle: 70-90-180 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 1.500 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 32 /min Punching force: 60 to throat: 250 mm : bis max. Ø 40x11 mm : 350x15 mm : 350x15 mm L-beam 90°: 120x120x10 mm : 45 mm square edge steel: 40 mm : 10 mm : Aufnahme bis max. 150x10 engine output: 5,5 kW weight: ca. 1600 kg Basic equipment: - Flat steel shears with knife set - Angle shears with knife set - Punch with quick release device for punches up to 40 mm - Support table for punching device - Triangular notching device - Support table for notching - bending station - Bending stamp with matrices V 40 and V 70 - electrical contact stop (1 meter) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 32 /min Punching force: 60 to throat: 500 mm : 40x11 mm : 350x15 mm : 350x15 mm L-beam 90°: 120x120x10 mm : 45 mm square edge steel: 40 mm : 10 mm : Aufnahme bis max. 150x10 engine output: 5,5 kW weight: 2012 kg Basic equipment: - Flat steel shears with knife set - Angle shears with knife set - Punch with quick release device for punches up to 40 mm - Support table for punching device - Triangular notching device - Support table for notching - bending station - Bending stamp with matrices V 40 and V 70 - electrical contact stop (1 meter) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1250 mm plate thickness: 5,5 mm pre-bending: 5,0 mm roll length: 1280 mm min. dia.: 210 mm roll diam. toproll: 140 mm weight: 1365 kg range L-W-H: 2.020 x 900 x 1.200 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1050 mm plate thickness: 3,3 mm pre-bending: 3,0 mm roll diameter: 90 mm min. dia.: 130 mm total power requirement: 1,1 kw weight of the machine ca.: 570 kg dimensions of the machine ca.: 2100 x 800 x 1130 mm Domestic equipments: - Asymmetrical 3-roll round bending machine with motor drive - Upper roller swung out - Conical bending device - Main engine with brake device Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

working length: 2050 mm : 2.0 mm max. wire thickness: 3.0 mm Underfloor: 110 mm motor strength: 165 mm motor strength: 22 kW bending speed: 5.2 mm/min length: 3150 mm height: 1150 mm width: 850 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bar material - diameter: Ø 35 mm I-beam section - flat steel: 60x10 mm L-beam: 50 mm tube diameter max.: Ø 60x2 mm square material: 45x45x3 mm roll diam. toproll: 162 mm roll diam. bottom roll: 152 mm Shaft diameter: 50/40 mm turning speeds: 3,3 m/min total power requirement: 1,5 + 0,75 kW weight: 450 kg range L-W-H: 1050x950x1450 mm Domestic equipments: - hydr. Delivery of the top roller - standard roller set - side straightening rollers - Upper roll holder: 50.0 mm - Under roller diameter: 40.0 mm - Control panel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 900 mm table load: 1.000 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 1,1 UpM T-slots: 6 x M16 Tilt Angle: 90-180-105 ° Tilting Speed: 30 sn min./90° dimensions: 2100x920x1100 mm weight of the machine ca.: 930 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2100 mm plate thickness: 13 mm pre-bending: 10 mm upper roll diameter: 230 mm lower roll diameter: 210 mm side roll diameter: 190 mm total power requirement: 7,5 kW weight of the machine ca.: 4.750 kg dimensions of the machine ca.: 4150x1400x1300 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG ...

flat steel: 350 x 15 mm round bar steel: 35 mm square edge steel: 30 mm L-beam: 80x80x8 mm hole diameter in sheet thickness: Ø 27 in 13 / Ø 20 in 18 mm blade length: 356 mm engine output: 3.0 kW Stroke rate: 34 Punching capacity: max. 500 kN weight: 950 kg dimensions: 1300x1100x1850 mm Standard equipment: - Knife set for flat steel - Complete knife set for angle steel shears - Complete normal punching equipment - Quick release device for punches up to 31 mm - Support table for punching device, rectangular notching and flat steel shears - Bending stamp with matrices V 40 and V 70 - Electric contact stop (1.000 mm) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 200 - 280 mm band length: 400 - 500 mm stroke: - mm total power requirement: 2 kW weight of the machine ca.: 3 t dimensions of the machine ca.: 3 LM m Package 5 x hacksaw / hacksaw machine / untested - partly in need of repair / spare parts carrier - 0278: RUCOCO RBS 280 A / Ø 280mm - automatic machine - 0664: SILISTRA HN 25 M / Ø 250 mm / saw blade 500 mm - 2395: BEHRINGER Super A-275 / Ø 275 / saw blade 450 mm / automatic machine - 3674: BEHRINGER Super 215 PU 2 / Ø 215 / saw blade 400 mm - 5708: KLAEGER / Ø approx. 210 / saw blade 400 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 51 mm Wheel width: 350 mm weight: 20 kg height adjustment: 575 - 975 mm Load capacity per arm: max. 700 kg Furnishing: - Safe workpiece support - by massive and heavy-duty galvanized steel rollers - Roller support steplessly height adjustable and clampable - Problem-free and efficient material transport for the supply and removal of workpieces techn. Details: - Load capacity, max. 700 kg - Standpipe diameter 74/52 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning length: 1500 mm turning diameter: 420 mm swing diameter over bed slide: 255 mm turning dia. in gap: 580 mm spindle bore: 52.0 mm turning speeds: 45 - 1800 U/min bed width: 250 mm spindle taper: DIN 55029 D 1-6 taper in tailstock: 4 MK quill travel: 140 mm total power requirement: 3.0 / 4.5 kW weight of the machine ca.: 1400 kg range L-W-H: 2570 x 900 x 1600 mm Equipment: - 3-axis digital display ES-12 V with LCD display - 3-jaw chuck DK11-200 mm / D6 - Clamping disk 350 mm - Fixed steady rest - passage diameter max. 135 mm - Follow-on steady rest - passage diameter max. 65 mm - Coolant system - Quadruple tool holder - Protective device for quadruple tool holder - Micrometer longitudinal stop - Slip clutch - Turret stop with fine adjustment - Thread gauge - Motor with magnetic brake according to CE standard - Foot pedal with brake function according to CE - Initial filling with Sh ...

pressure: 30.0 t punching cross-cut in cmm: 30.0 in 9.0 mm stroke: ca. 35 Hub/min throat: 610 mm stroke - stepless adjustable: 0 - 28.0 mm oil volume: 35.0 l work height max.: 1010 mm total power requirement: 4.0 kW weight of the machine ca.: 1200 kg. Features: - Electro-hydraulic punch press with long reach - Material/sheet metal scraper - Very large material support table (!) with adjustable depth stops - Continuously variable stroke adjustment - Freely movable foot switch, including protective cover - Side storage shelf - Assortment of punches and dies - Original operating instructions The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

L-beam: 40 x 5.0 (d 500) mm I - beam section - flat steel: 80 x 15 (d 700) mm I-beam section - upend: 50 x 10 (d 800) mm round material: 30.0 (d 700) mm bar material dia. max.: 60 x 2 (d 1200) mm square material: 50 x 30 x 3 mm range L-W-H: 670 x 530 x 1350 mm weight: 185 kg total power requirement: 0.75 kW Exhibition machine from 2021 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - robust electro-motorized ring/profile bending machine - horizontal and vertical work possible Machine head can be folded 90° - 1x freely movable foot switch - segmented standard rollers (divided) - 2x motor-driven rollers - manual delivery of the top roller - analog position display of the top rollers (scale) - manually adjustable side/straightening rollers - CE mark / declaration of conformity - Operating instructions in German The data for this ad was crea ...

pressure: 30.0 t punching cross-cut in cmm: 30.0 in 9.0 mm stroke: ca. 35 Hub/min throat: 610 mm stroke - stepless adjustable: 0 - 28.0 mm oil volume: 35.0 l work height max.: 1010 mm total power requirement: 4.0 kW weight of the machine ca.: 1200 kg. range L-W-H: 1400 x 700 x 1600 mm good condition () with a lot of application tools (stamps/dies) Furnishing: - electro-hydraulic hole punch, with large throat - Material/sheet metal scrapers including scraper plates - Large material support table, with adjustable depth stops - continuous stroke adjustment - freely movable foot switch including protective cover - Forklift pockets for easy transport - side storage area - lots of accessories + tools - including tool cabinet - Matrix base (for special size matrices) - Stamp holders (for special size stamps) - original user manuel The data for this ad was created with ModulMWS - the softwar ...

sheet width: 3100 mm plate thickness: 16,0 mm ST pre-bending: 20,0 mm ST diameter of upper rolls: 360 mm side roll diameter: 250 mm diameter of lower rolls: 330 mm total power requirement: 15,0 kW weight of the machine ca.: 13.200 kg. dimensions of the machine ca.: 5542 x 2100 x 1983 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with Mod ...

x-travel: 1000 mm y-travel: 360 mm z-travel: 400 mm spindle taper ISO: 40 ISO table:: 1370 x 320 mm feed:: H 80 - 830 / V 23-625 mm/min. turning speeds: H 35 - 1500 / V 45 - 1660 U/min distance spindle /table: H 30 - 430 / V 210-610 mm rapid traverse: Z Achse 750 mm/min throat: 305 - 805 mm T-slots: 3 x 14.0 mm table - swivable +/-: -45 / +45 ° workpiece weight: max. 300 kg coolant pump: 25.0 L/min. total power requirement: 7.6 kW weight of the machine ca.: 1540 kg range L-W-H: 1840 x 1830 x 2050 mm - Large rectangular guide in y and z axes - ensure increased stability - 8x automatic feeds and rapid traverse in all axes - driven by servo motor - Universal milling head system Huron, adjustable to all angular positions - Swiveling control panel with ergonomically placed switches - Heavy machine stand made of gray cast iron for vibration-free work - Very smooth running thanks to ground gea ...

pressure: 80.0 t chamfer lenght: 2600 mm distance between columns: 2200 mm column arm: 250 mm ram stroke speed: 90.0 mm/sec work speed: 7.5 mm/min return speed: 60.0 mm/sec work stroke: 160 mm dayligth: 380 mm table height: 900 mm oil volume: 150 ltr. voltage: 400 Volt weight: 5227 kg range L-W-H: 3750 x 1950 x 2400 mm Furnishing: - DELEM - CNC control model DA-58T - controlled axes: Y1 - Y2 and X - AKAS laser in front of the machine - manual crowning - Upper tool, deer foot - Lower tool, die block with 4Vs - SICK light barrier behind the machine - 2 front support arms - SIEMENS - electrical system - BOSCH / HOERBIGER hydraulic system - CE mark / declaration of conformity - Operating manual: machine and control - Safety manual: press brakes The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 t chamfer lenght: 4100 mm distance between columns: 3700 mm column arm: 415 mm stroke: max. 215 mm dayligth: 410 mm ajustment speed: 200 mm/sec working feed: 10.0 mm/sec return speed: 150 mm/sec work height max.: 1080 mm table width: 100 mm Control: CYBELEC oil volume: 160 ltr. voltage: 400 V power capacity: 8.5 kW weight: 10200 kg range L-W-H: 4800 x 1800 x 2600 mm - in checked conditions - machinevideo - https://www.youtube.com/watch?v=Phcik_oo4CE Equipment: - BEYELER electro-hydraulic CNC press brake - CNC CYBELEC control unit DNC 1200 PS/B” High-resolution screen Clear, concise menus in the operators language Tool and product library Swiveling control panel, front right - CNC-controlled axes (Y1+Y2-X) - CNC-controlled backgauge adjustment (X-axis) 2x manually adjustable stop fingers - Manual upper tool clamping - Manual lower tool clamping - Rear safety device (s ...

sheet width - max.: 200 mm plate thickness: 6 mm flat steel: 70 x 7 mm round bar steel: 13 mm weight of the machine ca.: 50 kg dimensions of the machine ca.: 800 x 500 x 1800 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 305 mm capacity 90 degrees: flat: 350 x 200 mm capacity 45 degrees: round: 250 mm capacity 45 degrees: flat: 230 x 200 mm capacity 60 degrees: round: 175 mm capacity 60 degrees: flat: 170 x 100 mm cutting speed: 18 - 110 m/min vice: max. 350 mm dimensions of saw-band: 3370 x 27 x 0.9 mm engine output: 1.5 / 1.8 kW weight of the machine ca.: 880 kg range L-W-H: 1700 x 2200 x 2000 mm Equipment: - robust, electro-hydraulic fully automatic band saw - user-friendly controls - Mitre cuts left to 45 . possible in automatic mode - Mitre cuts up to 60° . only possible in semi-automatic mode - Hydraulic power unit with automatic . pressure cut-off when idling - Stationary base frame with large chip drawer and automatic cooling system - infinitely variable saw blade speed adjustment (ESC) - rotating chip brush - remnant min. 80 mm - operating instructions (PDF) The data for  ...

drill diameter: 2.0 - 20.0 mm lip angle: 90 - 135 ° turning speeds: 4800 U/min voltage: 230 Volt engine output: 0.12 kW weight: 8.6 kg range L-W-H: 285 x 130 x 170 mm The handy DG 20 M drill grinding machine is ideal for grinding twist drills made of HSS, cobalt and hard metal. Thanks to the adjustable tip angle of 90° to 135°, this model can be used universally for 2-edged twist drills. Properties: - For grinding HSS and hard metal twist drills from 2 - 20 mm - ER 20 and ER 25 collets also enable clamping of intermediate sizes - Optimum grinding result thanks to the specially guided collet - Includes device for sharpening the drill tip - Universally adjustable tip angle from 90° - 135° - Fast and easy grinding process Scope of delivery: - CBN grinding wheel - ER 20 collets, 3 - 12 mm 11 pieces (3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 /12 / 13 mm) - ER 25 collets, 14 - 20 mm 7 pieces  ...

bore capacity in steel (diameter): 32,0 mm throat: 230 mm bore stroke: 120 mm morse taper: 3 MK table:: 400x320 mm turning speeds: 105 - 1725 U/min total power requirement: 1,2 kW weight: 245 kg range L-W-H: 470x810x1710 mm Furnishing: - Compact, stable cast iron construction in a modern design - Infinitely variable speed control - is changed The speed is read on a digital display - Table height adjustment via rack and crank - Right and left rotation of the quill for thread cutting - Powerful 2-stage motor, speed range from 105 - 1725 rpm - Base plate with T-slots for clamping high workpieces - Safety switch with undervoltage release - The spindle runs in the precision ball bearing scope of delivery - Key chuck 1 - 13 mm / B 16 - Drill chuck arbor MK 3 / B 16 - Reducing sleeve MK 3/2 - Digital speed display - LED machine light - Height-adjustable protective cover The data for this ad w ...

sheet width: 1050 mm plate thickness: 3.3 mm pre-bending: 3.0 mm roll length: 1050 mm roll diameter: 90.0 mm min. dia.: 130 mm engine output: 1.10 kW weight: 570 kg range L-W-H: 1.800 x 800 x 1.130 mm Exhibition machine from 2026 With only approximately 2 operating hours Condition like new Special price upon request Furnishing: - Robust electro-mechanical bending machine - 2x central rollers driven by an electric motor (top and bottom roller) - Top roller can be swiveled out manually, with folding bearing - including conical bending device - freely movable control panel - Lower roller manually adjustable, by hand wheel - asymmetrical roller arrangement - self-braking main motor - Safety device (safety line with switch unit) - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized side roller adjustment - Digital position display for  ...

thread dia.: M6 - M36 turning speeds: 30 - 150 U/min working area: max. 1200 R angle adjustable from - to: 0 - 90 Grad voltage: 230 V engine output: 1200 W weight: 65,0 kg - Includes quick-change chuck - for use with taps - for through holes and blind holes - Swivel motor unit for thread cutting - at any desired angle between 0° and 90° - Higher accuracy compared to manual thread cutting - Thread is guaranteed to be right-angled (90°) - High productivity - significant time savings compared to manual thread cutting - Quick-change chuck with integrated slip clutch - Includes swivel arm with large radius - for easy positioning of the tap on the workpiece - Highly economical due to low investment and maintenance costs - For thread cutting in steel, stainless steel, aluminum and non-ferrous metals Scope of delivery - Operation via touchscreen - Digital drilling depth display - Quick-change ...

cutting diameter: 305 mm saw band length: 3375 mm cutting width: 350 mm dimensions of saw-band: 3375 x 27 x 0,9 mm : 305 mm : 260 mm : 350 x 200 mm : 250 mm : 230 mm : 230 x 200 mm : 175 mm : 155 mm : 170 x 100 mm total power requirement: 1,5 / 1,8 kW weight of the machine ca.: 0,7 t dimensions of the machine ca.: 1,5 x 1,8 x 1,9 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 4 Monate ab Auftragse : Türkei : 53900 € : 1018.71 € : Doppelsäulenführung : 7000x41x1,3 mm : 15 - 120 m/min : 560 mm : 540 mm : 810 x 530 mm : rund 520 mm, quadrat 520 : rund 520 mm, quadrat 520 : rund 330 mm, quadrat 330 : 875 mm : 1.1 kW : 4 kW : 0.12 kW : 3850 mm : 1700 mm : 2450 mm : 3400 kg hydraulic vice digital readout for scale of bending angle hydraulic clamping of sawing arm turning of sawing arm by hand continuously variable down speed of sawing arm automatic sawing frame lifting after cutting sensitive cutting pressure adjustment subject to material condition hydromechanic tape tension readout by manometer mobile control panel angular geared conical heavy duty gear unit driven chip brush tape guiding by hard metal sheet plates and rolls automatic tape break lock coolant equipment HYDRAULIC UPLIFT OF SAWING FRAME user manual in GERMAN or ENGLISH (roller  ...

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 16700 € : 320.64 € : Schwenkrahmen : 4800x34x1,1 mm : 15 - 120 m/min : 360 mm : 360 mm : 510x360 mm : rund 360 mm, quadrat 360 : rund 250 mm, quadrat 220 : rund 280 mm, quadrat 260 : 860 mm : 0.37 kW : 3 kW : 0.12 kW : 2650 mm : 1210 mm : 1870 mm : 1450 kg Hydraulic vice Inverter for contious variable band speed Continuously adjustable saw arm lowering speed Hydromechanical blade tension can be read via pressure gauge Control panel Chip brush Coolant equipment Operating instructions in German or English The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 61900 € : 1169.91 € : Doppelsäulenführung : 6000x41x1,3 mm : 20-100 m/min : 540 mm : 540 mm : 670x540 mm : rund 540 mm, quadrat 540 : rund 510 mm, quadrat 510 : rund 270 mm, quadrat 250 : 805 mm : 2.2 kW : 4 kW : 0.12 kW : 3100 mm : 2350 mm : 2150 mm : 3800 kg NC control double column band saw on linear guidelines 3° cutting angle blade brush control panel hydraulic feeding vice hydraulic vice hydromechanical blade tensioning inverter optical height adjustment proximity switch for sensing blade slippage material limit shaft pressure adjustment coolant pump saw blade security switch user manual in GERMAN or ENGLISH OPTIONS: hydraulic top clamping micro coolant equipment laser cutting line ALTERNATIVE: model BMSO 540 CGS NC (with servo instead of hyraulic feed) € 70.200,-- The data for this ad was created with ModulMWS - the softw ...

: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 54900 € : 1037.61 € : Doppelsäulenführung : 5400x41x1,3 mm : 20-100 m/min : 440 mm : 440 mm : 610x440 mm : rund 440 mm, quadrat 440 : rund 430 mm, quadrat 430 : rund 320 mm, quadrat 260 : 807,5 mm : 1.1 kW : 4 kW : 0.12 kW : 2850 mm : 2350 mm : 2000 mm : 3600 kg NC control double column band saw on linear guidelines 3° cutting angle blade brush control panel hydraulic feeding vice hydraulic vice hydromechanical blade tensioning inverter optical height adjustment proximity switch for sensing blade slippage material limit shaft pressure adjustment coolant pump saw blade security switch user manual in GERMAN or ENGLISH OPTIONS: hydraulic top clamping micro coolant equipment laser cutting line ALTERNATIVE: model BMSO 440 CGS NC (with servo instead of hyraulic feed) € 61.900,-- The data for this ad was created with ModulMWS - the sof ...

: neu : ca. 4 Monate ab Auftragse : Türkei : 22700 € : 435.84 € : Doppelsäulenführung : 4800x34x1,1 mm : 20-100 m/min : 380 mm : 380 mm : 430x380 mm : 590 mm : 0.55 kW : 3 kW : 0.12 kW : 2900 mm : 950 mm : 1660 mm : 1342 kg blade brush control panel hydraulic vice optical adjustment switch hydromechanical blade tension inverter mechanic top clamping material limit shaft coolant pump saw blade security switch gearbox pressure adjustment 1,2 meter roller table user manual in GERMAN or ENGLISH The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 45100 € : 861.41 € : Doppelsäulenführung : 5200x34x1,1 mm : 20-100 m/min : 360 mm : 360 mm : 610x360 mm : rund 360 mm, quadrat 360 : rund 360 mm, quadrat 360 : rund 325 mm, quadrat 265 : 735 mm : 1.5 kW : 3 kW : 0.12 kW : 2850 mm : 2250 mm : 1870 mm : 2400 kg NC control double column band saw on linear guidelines 3° cutting angle blade brush control panel hydraulic feeding vice hydraulic vice hydromechanical blade tensioning inverter optical height adjustment proximity switch for sensing blade slippage material limit shaft pressure adjustment coolant pump saw blade security switch user manual in GERMAN or ENGLISH OPTIONS: hydraulic top clamping micro coolant equipment laser cutting line ALTERNATIVE: model BMSO 360 CGS NC (with servo instead of hyraulic feed) € 50.900,-- The data for this ad was created with ModulMWS - the softwa ...

: neu : ca. 4 Monate ab Auftragse : Türkei : 34400 € : 657.04 € : Doppelsäulenführung : 6000x41x1,3 mm : 20-100 m/min : 540 mm : 540 mm : 750x540 mm : rund 510 mm, quadrat 450 : rund 270 mm, quadrat 250 : 695 mm : 4 kW : 0.12 kW : 3000 mm : 1300 mm : 2150 mm : 2445 kg hydraulic vice digital readout for scale of bending angle hydraulic clamping of sawing arm turning of sawing arm by hand continuously variable down speed of sawing arm automatic sawing frame lifting after cutting sensitive cutting pressure adjustment subject to material condition hydromechanic tape tension readout by manometer mobile control panel angular geared conical heavy duty gear unit driven chip brush tape guiding by hard metal sheet plates and rolls automatic tape break lock coolant equipment hydraulic uplift of sawing frame 3° inclined saw band user manual in GERMAN or ENGLISH (the vertical hydraulic clam ...

: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 46400 € : 886.24 € : Doppelsäulenführung : 6800x41x1,3 mm : 20-100 m/min : 560 mm : 820 x 540 mm : rechteck 550 x 540 mm : rechteck 360 x 540 mm : rechteck 550 x 540 mm : 880 mm : 1.1 kW : 4 kW : 0.12 kW : 3800 mm : 1750 mm : 2350 mm : 3200 kg hydraulic vice digital readout for scale of bending angle hydraulic clamping of sawing arm turning of sawing arm by hand continuously variable down speed of sawing arm automatic sawing frame lifting after cutting sensitive cutting pressure adjustment subject to material condition hydromechanic tape tension readout by manometer mobile control panel angular geared conical heavy duty gear unit driven chip brush tape guiding by hard metal sheet plates and rolls automatic tape break lock coolant equipment HYDRAULIC UPLIFT OF SAWING FRAME user manual in GERMAN or ENGLISH (roller table see photo - option ...

: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 23800 € : 456.96 € : Doppelsäulenführung : 5200x41x1,3 mm : 20-100 m/min : 460 mm : 460 mm : 650x460 mm : rund 380 mm, quadrat 380 : 590 mm : 0.55 kW : 4 kW : 0.12 kW : 3100 mm : 1000 mm : 1800 mm : 1520 kg blade brush control panel hydraulic vice hydromechanical blade tension inverter linear way material limit shaft height adjustment pressure adjustment coolant pump saw blade security switch gearbox 1,2 meter roller table user manual in GERMAN or ENGLISH OPTION: turn table for mitre cuts hydraulic top clamping from above The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 9400 € : 181.42 € : Schwenkrahmen : 2730x27x0,9 mm : 35-70 m/min : 230 mm : 230 mm : 240x230 mm : 590 mm : 0.37 kW : 1.3 kW : 0.12 kW : 1700 mm : 800 mm : 1500 mm : 530 kg blade brush control panel height adjustment switch hydromechanical blade tension inverter mechanic top clamping material length stop coolant pump saw blade security switch 1,2 meter roller table users manual in GERMAN or ENGLISCH The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 4 Monate ab Auftragse : Türkei : 72800 € : 1375.92 € : Doppelsäulenführung : 9500x54x1,6 mm : 20-100 m/min : 1020 mm : 1020 mm : 1020x1020 mm : rund 675 mm, quadrat 675 : 535 mm : 2.2 kW : 7.5 kW : 0.12 kW : 4500 mm : 1700 mm : 2750 mm : 5860 kg blade brush control panel hydraulic vice hydraulic blade tension inverter linear ways height adjustment by optical sensor automatic adjustment of blade guide arm, syncrounos to vice movement senitive pressure adjustment coolant pump saw blade user manual in GERMAN or ENGLISH OPTIONS: hydraulic top clamping chip conveyer turn table for turning the machine for mitre cutting roller tables and band saw blades The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 38700 € : 739.17 € : Doppelsäulenführung : 8200x41x1,3 mm : 20-100 m/min : 810 mm : 810 mm : 850x810 mm : rund 480 mm, quadrat 480 : 585 mm : 1.5 kW : 4 kW : 0.12 kW : 3900 mm : 1200 mm : 2350 mm : 3080 kg 2° inlined saw band optical height adjustment linear guides control panel security switch pressure adjustment hydraulic vice chip brush hydromechanical blade tensioning coolant pump heavy duty gearbox 1,2 m roller table user manual in GERMAN or ENGLISH OPTIONS: turn table for mitre cuts hydraulic top clamping from above roller tables and band saw blades The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : 2026 : 060216 : prompt, Zwischenverkauf v : Türkei : 20700 € : 397.44 € : 1 : Schwenkrahmen : 5200x34x1,1 mm : 20-100 m/min : 440 mm : 440 mm : 610x440 mm : rund 410 mm, quadrat 410 : rund 320 mm, quadrat 250 : rund 410 mm, quadrat 410 : rund 320 mm, quadrat 285 : 860 mm : 0.55 kW : 3 kW : 0.12 kW : 2800 mm : 1210 mm : 1870 mm : 1540 kg hydraulic vice digital readout for scale of bending angle hydraulic clamping of sawing arm turning of sawing arm by hand continuously variable down speed of sawing arm automatic sawing frame lifting after cutting sensitive cutting pressure adjustment subject to material condition hydromechanic tape tension readout by manometer mobile control panel angular geared conical heavy duty gear unit driven chip brush tape guiding by hard metal sheet plates and rolls automatic tape break lock HYDRAULIC UPLIFT OF SAWING FRAME user manual in GERMAN o ...

: neu : 2026 : 060215 : prompt, Zwischenverkauf v : Türkei : 9280 € : 179.1 € : 1 : Schwenkrahmen : 3160x27x0,9 mm : 20-100 m/min : 270 mm : 270 mm : 340x220 mm : rund 230 mm, quadratisch : rund 150 mm, quadratisch : rund 180 mm, quadratisch : 910 mm : 0.37 kW : 1.5 kW : 0.12 kW : 1730 mm : 770 mm : 1460 mm : 476 kg DIGITAL ANGLE READ OUT blade brush control panel swivel frame infinitely adjustable lowering with hydraulic cylinder hydraulic lifting of the saw frame quick lowering with automatic switchover to working speed using a sensor pin mech. Vice with quick clamping coolant equipment machine base chip collecting tray user manualin GERMAN or ENGLISH OPTIONS: Roller tables and band saw blades on request The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.