baling press used for sale

pressure: 100 t throat: 350 mm stroke: 130 mm stroke of worktool slide: 3070 Hub/min ram adjustment: 100 mm ram surface: 500x300 mm table surface area: 1000x600 mm feed - rapid adjustment: total power requirement: kW weight of the machine ca.: 9,8 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Contact pressure gauge, pressure gauge with switching contacts MANOMETERWERK WITTGENSDORF 0 - 600 kPa (0 - 6 bar) Switch type: 2/Z112-1 Switching capacity: 220 V AC / DC 30 W (VA) Housing diameter: Ø 160 mm Accuracy class: 1 Connection thread: M20 x 1,1,01 5 New !' Dimensions: 210 x 205 x 150 mm

1:1 Pressure Converter, Pressure Converter VDO MESS- UND REGELTECNIK GmbH Type: 21 / 16 Best: No. 055834 Supply air pressure: 1.4 - 4.4 bar to Measured value: 4 mbar - 4.0 bar with accessories New ! Dimensions: 78 x 78 x 45 mm

Qty. 1 Second-hand extrusion press line – in storage – never installed! Mfc.: Korean Manufacturer Force: 1650 UST Built: 2024 Type: Direct Single Action Horizontal Short Stroke Back Loading Aluminum Hydraulic: Rexroth PLC: Mitsubishi Diameter of billet: 152 mm (6 inch) Length: 400 – 750 mm Size of container: Φ157 mm × 800 mm Size of exit hole: Φ180 × 250 mm Container Size Inner Dia.: 164 mm (6˝) Length: 700 mm Main Ram Stroke: 1200 mm Scope of supply: Loading Lift System Billet Pushing Induction heating Furnace Billet Conveyor for Discharge Billet Feeding into Press Cooling System Hot Saw Run-out Table Double Puller Stretcher Finishing Saw Dies Furnace Aging Furnace

Contact pressure gauge, pressure gauge with switching contact WIKA 212.20.100 Cont. 821.111 0 to 250 bar Ø 100 mm with diaphragm seal (approx. 1500 mm cable) New! Dimensions: 120 x 60 x 55 mm

Continuous veneer press panel size 3200/1400mm External and inner hydraulic cylinders Press pressure can be adjusted separately Panel heating steam and electricity

Pressure transmitter REXROTH HM20-20/250 R901342027 Measuring range: 0 - 250 bar U(signal): 0.1 - 10 V DC U(supply): 18 - 36 V DC used, tested ! Dimensions: 130 x 22 x 20 mm

HL 60 ton Capacity: 60 ton Passage between uprights: 410 mm Distance between table -- ram: 670 mm

Pressure transmitter HYDROTECHNIK HT-PD 3403-53-NO.54 Measuring range: 0 - 210 bar U(signal): 0.1 - 10 V DC U(supply): 12 - 32 V DC used, tested ! Dimensions: 100 x 40 x 22 mm

HL 60 ton Capacity: 60 ton Passage between uprights: 410 mm Distance between table -- ram: 670 mm

Pressure Transmitter, Piezoresistive Pressure Transmitter PMA P21R/120 51863 0413.0250 Measuring range: 0 - 120 bar I(signal): 4 - 20 mA DC U(supply): 8 - 28 V DC used, tested ! Dimensions: 100 x 40 x 22 mm

Weingarten AR 63 ton Capacity: 63 ton Max adjustable stroke: 8 > 100 mm Drawning speed: 56/84 str/min Dimension of the table: 620 x 500 mm Dia table hole: 250 mm Punchholder dia: 40 mm Course adjustment: 63 mm Weight: 4 ton

Pressure transmitter, level transmitter HENGESBACH KERAMESS G1/2B 30mbar4/2LF Measuring range: 0 - 100 bar < br /> Pmax: 4 bar I(signal): 4 - 20 mA DC U(supply): 13 - 36 V DC stainless steel ! used, tested ! Dimensions: 160 x 90 x 70 mm

Veneer press Brand: ORMA Type: NPC/DIGIT 6/90 New machine Technical datas: Press area: 2500x1300 mm Amount cylinder: 6 Lift & max. press opening: 400 mm Total pressure: 90t Electro-heater 18 kW for thermo-oil (up to 120°C) Optional: - Aluminium coating - 650 mm stroke - Parallelism control by sensor - Extra charge for down stroke design - Extra charge for temperature up to 150°C - Extra charge for temperature up to 200°C - Mylar protection foil 350,00 ? per panel - Pressure plate covered with glass fiber fabric Teflon - Hardware for Industry 4.0

Pressure regulator manually adjustable, ultrapure gas regulator DRUVA type: LMD-500-01 inlet pressure: max. 50 bar outlet pressure: 0.5 - 6 bar stainless steel ! Dimensions: 125 x 115 x 50 mm

New hot press, hydraulically Brand: ITALPRESSE Type XL/6 30-13 PEA Golden electric heating plate surface anodized to ensure high surface hardness and excellent corrision protection. - Electrical - heating plates: 3000 x 1300 mm - Total pressure: 120 to. - Number of hot plates: 2 pc. - Number of floors: 1 pc. - Stroke: 350 mm - Day light opening: 350 mm - All-round feeding - Number of cylinders: 6 pc. - Diameter of cylinder: 85 mm - Power consumption (hydraulic unit): 3 kW - Electric - combi - heating plates made out of two components: Aluminium - electric - heating plate Iso printing plate - Heating power 22 KW - High pressure isolation plates - Operating temperature: 70 - 90° C. - Max. Temperature: 120° C. - Supply: 400V/50 Hz - Safety accordance with CE standard Standard equipment: - Movement of the press table with rack and pinion parallel guidance at t ...

Pressure regulator hand-adjustable, ultrapure gas regulator DRÄGER TESCOM type: 44-3262-242H283 inlet pressure: max. 35 bar outlet pressure: 0 - 35 bar stainless steel ! Dimensions: 135 x 135 x 70 mm

various pressure zones IMA - from stock - price on request

Briquet press Make: Reinbold Type: RB 30 SV New machine Technische Daten: Reserve container approx. 1044 x 1044 x 1010 mm Hydraulic motor: 5,5 kW Briquett-Ø 50mm Oil quantity: 100 l Weight: Approx. 700 kg The max. material moisture should not exceed 18% Description The whole briquet unit consist of an easy-maintenance hydraulic, a powerful drive for the agitator as well as the the fill and press cylinders. The unit is compact placed on the machine. The accessable construction makes the service easy. Hydraulic unit consists of: motor, pressure switch, valve block, manometer, oil filter Switch box mounted on container, with SPS-Control Automatic Star-Delta-start Low oil switch Screw conveyor channel, screw conveyor Manual cylinder control Automatic end positioning of all cylinders Safety switch for oil temperature Connection for transport hose or c ...

Pressure regulator manually adjustable, ultrapure gas regulator DRÄGER TESCOM type: 44-2260-242-010 inlet pressure: max. 27 bar outlet pressure: 0 - 1.7 bar stainless steel ! Dimensions: 120 x 120 x 90 mm

CONTROLS   PC controller BECKHOFF PRESS DESIGN   drive system: knuckle-joint SLIDE   total force (nominal): 250 to   stroke: 61 mm   stroke rate (max.): 60 /min COUNTER RAM   nominal force: 75 to   stroke: 15 mm V-RING   nominal force: 75 to   stroke: 13 mm TOOL DIMENSIONS   lower table (left-right): 540 mm   lower table (front-back): 540 mm   upper table (left-right): 540 mm   upper table (front-back): 540 mm   shut height max.: 320 mm   ram adjustment: 145 mm   distance between columns (H-frame): 560 mm   passline opening (free passage in side columns): 270 mm STRIP-FEEDER   feeder type: roll feeder   sheet width max.: 250 mm   sheet thickness max.: 10 mm   feeding step max.: 999.99 mm   sheet length min: 1900 mm   pilot release system: yes   band lubrication system: yes Complete refurbished fineblanking press: disassembly into indivi ...

Pressure reducer, pressure regulating valve MANKENBERG 652 G1 6570036TA-EM Temp.: 130°C 2 to 5 bar PN 40/10 stainless steel !' New !' Dimensions: 310 x 145 x 115 mm

CONTROLS   PLC SIEMENS S7 300 PRESS DESIGN   drive system: hydraulic PRESS FORCES   total force (nominal): 800 to PRESS TABLE   table surface (left-right): 2000 mm   table surface (front-back): 2000 mm   height above floor level: 700 mm SLIDE   table surface (left-right): 2000 mm   table surface (front-back): 2000 mm   stroke: 900 mm SLIDE (HYDR. PRESS)   approximation velocity max.: 400 mm/s   working velocity min.: 5 mm/s   working velocity max.: 160 mm/s   return velocity max.: 300 mm/s TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 1700 mm   distance between columns (H-frame): 2100 mm ELECTRICAL SPECIFICATIONS   total power consumption: 370 kW   mains voltage: 400 V   mains frequency: 50 Hz DIMENSIONS / WEIGHTS   total weight approx.: 81000 kg ATTACHMENTS (PRESSES)   press automation: yes   gripper transfer system ...

Pressure relief valve, relief valve LESER TUEV-SV 95-425 5394.2302 D0 10 D/G 0.36 F 0.26 10 bar G1/2 Material: stainless steel 1.4408 New ! Dimensions: 182 x 72 x 55 mm

CONTROLS   PLC SIEMENS S7-400 PRESS DESIGN   drive system: hydraulic   number of suspensions: 1   slide ejectors / cushion: no   table cushion: no   opening in table: no   feedstock transport direction: back-front PRESS FORCES   total force (nominal): 1000 to PRESS TABLE   table surface (left-right): 2066 mm   table surface (front-back): 2000 mm   height above floor level: 630 mm SLIDE   stroke: 900 mm SLIDE (HYDR. PRESS)   approximation velocity max.: 600 mm/s   working velocity min.: 15 mm/s   working velocity max.: 40 mm/s   return velocity max.: 390 mm/s   return force: 100 to TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 1710 mm   distance table - slide max.: 1700 mm ELECTRICAL SPECIFICATIONS   total power consumption: 160 kW   mains voltage: 400 V   mains frequency: 50 Hz DIMENSIONS / WEIGHTS   height abov ...

Pressure Switch MERTIK 612.01 0.1 to 1.85 kp/cm² Switching Capacity(AC): 2.5 A 380 V 50 / 60 Hz Switching Capacity(DC): 0.16 A 220 V IP55 New ! Dimensions: 180 x 55 x 135 mm

PRESS DESIGN   drive system: knuckle-joint   frame design: H-frame, monoblock SLIDE   total force (nominal): 160 to   stroke: 60 mm   stroke rate (max.): 72 /min COUNTER RAM   nominal force: 40 to   stroke: 60 mm V-RING   nominal force: 50 to   stroke: 13 mm TOOL DIMENSIONS   lower table (left-right): 470 mm   lower table (front-back): 470 mm   upper table (left-right): 500 mm   upper table (front-back): 470 mm   shut height max.: 277 mm   ram adjustment: 80 mm   distance between columns (H-frame): 500 mm   passline opening (free passage in side columns): 220 mm STRIP-FEEDER   feeder type: roll feeder   sheet width max.: 210 mm   sheet thickness max.: 6 mm   feeding step max.: 180 mm ELECTRICAL SPECIFICATIONS   mains voltage: 380 V   mains frequency: 50 Hz DIMENSIONS / WEIGHTS   space requirements -left/right-: 1950 mm   space requiremen ...

Pressure regulator manually adjustable, ultrapure gas regulator DRÄGER TESCOM type: 44-2262-242-009 inlet pressure: max. 27 bar outlet pressure: 0 - 7 bar stainless steel ! Dimensions: 120 x 120 x 60 mm

General Manufacturer: Transmatic Type: TS-3M Year of Make: 2007 Plate size: 38 x 38 cm Maximum pressure: 600 g/cm2 Temperature setting: 50 – 305°C Condition Condition: Used Functional: Tested and fully functional

Pressure regulator manually adjustable, ultrapure gas regulator DRÄGER TESCOM type: 44-2261-242-010 inlet pressure: max. 27 bar outlet pressure: 0 - 3.5 bar stainless steel ! Dimensions: 120 x 120 x 60 mm

Pressure regulator manually adjustable, ultrapure gas regulator DRÄGER TESCOM Type: 44-3262H283-001 Inlet pressure: max. 35 bar Outlet pressure: 0 - 7 bar stainless steel ! Mint ! Dimensions: 140 x 140 x 100 mm

Manufacturer: Kallesoe, Width mm: 1350, Length mm: 5000, FREE TEXT: With feeding KL20 and stacking line,

Dough section and knitting machine Sinmag SM-330Y semi-automatic - Semi-automatic roll press - Sharing and impact - Manufacturer: Sinmag Europe - 30 pieces - Model: SM-330Y - Dough insert: 750- 2400 grams - Unit weight: 25-80 grams - Machine weight: 340 kg - 400 Volt/ 3Ph/ 50Hz - Year of construction 10 / 2020

Manufacturer: Hess , Type: Rahmenpresse, Year: ca.1995, Work piece width min-max mm: ca.1500, Min.-max. workpiece length in mm: 2500, Min.-max. workpiece height in mm: 10-90, Working widht max mm: 2500, Hydraulical/pneumatical: elektrisch, Year :ca.1995

Key data: 400 t, 160 mm

Nominal forming force of the press 400 t Table 1250x825 mm Dimensions of the ram 900x560 mm Lifting of the ram 30-160 mm Machine weight 22 T Power of the main electric motor 30 kW Dimensions L x W x H --> 1550 x 2900 x 3360 mm complete with press line = Production LASA, Spain year 2008 = - Decoiler 4 t - coil width 400 mm, coil outer diam. 1600 mm Coil inner diameter 450/550 mm, unwinding speed up to 25 m/min - Pre-feed machine RAPID PRESS max. width 420 mm, material up to 3 mm, max. speed 70 m/min - Documents, electrical diagrams, etc.

Dough dividing and rounding machine Bun press Fortuna Automat Size 3 Partial head reworked with stainless steel knife NEW Dough insert up to 2300g depending on TA Dough divider without knitting plate E-system NEW DGUV V3 tested Connection 400V, 1.6 kW, 16A-CEE plug Dimensions: 720 x 800 x 1510 mm Used machine overhauled + Spare parts service Option: Platform or chassis Maintenance contract Warranty E-Box Service Package We have a wide range of bread presses!

Offer 25021 Technical data approx.: - Compressive force 250 t - Projection 360 mm - Table size approx. 1100 x 800 mm - Diarrhea hole in the table approx. 320 mm - Tappet area approx. 800 x 475 mm - Peg hole in the tappet mm - Plunger adjustability 110 mm - Stroke adjustment 30 - 140 mm - Max. stroke rate 45 1/min - Pneumatic connection 6 bar - Drive 400 V / 22 kW - Space requirement approx. W 1400 x H 2990 x D 2700 mm - Weight approx. 13 T

SMG 320 cold forming press for sale. Year of build 1981 Model HPU 315-1300/1150 The machine has a crack in the head piece. Drive power: 2 x 55 KW Oil volume of one tank filling 3800 liters Maximum ram force: 3200 KN Drive cylinder: 3 pieces Cylinder 1: 2000 KN Cylinders 2+3: 600 KN each maximum adjustment: 310 mm Find more here - / Contact us at -

Manufacturer: Friz, Year: 1997, Type: MFP 22/14/11, Press length mm: 1100, Pressing width mm: 800, Work piece thickness max mm: 95, Year :1997

2004 Alphatech Model RPS4000 Description: Electro-hydraulically driven frame press Series: Type:RPS 4000 Date of manufacture:12.2003 plunger force From approx. 4000 kN kN plunger force Up to approx. 916 kN kN plunger stroke approx. 600 mm Installation table - column max. 1050 mm Max. plunger rapid speed approx. 600 mm/sec Max. Splunger working speed approx. 41.7 mm/sec Max. Return speed approx. 440 mm/sec Table surface (WD) approx. 900965 mm Full volume Hydrauliko! HLP 46 approx. 5300 litres Main drive power 290 kW+ 255kW + 130kW Control voltage 230 VAC/ 24VDC Operating voltage 400 V /50 Hz Colour scheme: System RAL 1014 Control cabinet, control panel and hazard labelling RAL 2002 Find more here - / Contact us at -

Liebergeld Li-transmatic Colombo Agostino for sale. Year of build 1990 Model G 400/1100/250/5 Nominal pressing force: 4000 KN Stroke : 250 mm Infinitely variable stroke rate: 20 - 60 1/min Table top usable, width x depth: 1100 x 900 mm Plunger plate usable, width x depth: 1050 x 800 mm Installation height, bottom stroke, top adjustment: 720 mm Vertical adjustability of the ram: 20 mm Table ejector cam-controlled Find more here - / Contact us at -

Manufacturer: Europress, Type: 1000 VE, Power kg/h: 35 m³/h, Supply case m³: 0,53, Hydraulikal power kW: 5,5, Ballenpresse: yes, Pressdruck kN/ to: 300, Einfüllöffnung b x h x L mm: 700 673, Ballenmass b mm x l mm x h mm : 500 x 650, Ballengewicht kg: 50 - 200, Year :2001

A vulcanising press with 4 shelves, it was purchased as a spare for the currently used one and has been standing unused since new, in total it has worked for us 0h. Model XL8-350T-700x700x4 l´LC Pressure 350T 700x 700mm thickness 6()mm Hotplate resistance Ra:,I .6a (2.5 μm) - Type of heating electr. Max. temperature 200 ‘C Pressure on workplate approx. 7 I kg-´cm2 piston diameter I 600mm -f 500mm Hydraulic pressure 16Mpa Machine structure Ko1umno,-a Motor power .of hydtaulic station ,- 5.5kW Heating power for J..ai:d working plate 9 x 0.9kW= 8.lkW Weight p,-assembly approx. 12000 g Press dimensions : Approximately 2800x I 200,´350Chnin Find more here - / Contact us at -

Offer 25020 Specifications: - Compressive force 200 t - Projection 400 mm - Table size approx. 1000 x 750 mm - Diarrhea hole in the table approx. 320 x 220 mm - Pushrod area 940 x 400 mm - Plunger adjustability 100 mm - Stroke adjustment 20 - 130 mm - Drive 380 V / 10 kW - Space requirement approx. W 1400 x H 2980 x D 2900 mm - Weight approx. 13000 kg

Qty. 1 Second-hand aluminium extrusion press line Mfc.: TCS, Asimakis, Sistem Teknic Force: 2200 MT Billet dia.: 8” Built: 1979 Still in operation! Type: Hydrauli horizontal Hydraulic pressure: 235 bar Scope of supply: Billet Loader Billet Furnace Hot Shear Billet Transfer Table Extrusion Press Run-Out Table Single Puller Cooling Table Stretcher Profile Stacker Ageing Furnace

Manufacturer: Ocamc, Type: Kopp Elta, Year: 1990, Min.-max. pressing length in mm: 2500, Min.-max. pressing height in mm: 1200, Min.-max. pressing depth in mm: 600, Compressed air bar: 6, Year :1990

Erika Record Gr. 7 20 pcs dough dividing and knitting machine Year:2017 - Manufacturer: Erika Record Karl Schmidt GmbH - Semi-automatic roll press - To share and make an impact - Weight range: 70gram to 160gram - Type: 7 20 pcs - 20 pieces - 400 Volt 0.75kW 50Hz - Year of construction 2017

Manufacturer: Istel, Type: Eckschrankpresse, Bauyeshr : 1998, Hydraulical/pneumatical: motorisch/pneumatisch, Press hight mm: 1050/900/800, Press depth mm: 1050/900/800, Machine rigging: automatisch, Compressed air bar: 6, Gewicht ca. kg : 2000, Year :1998

Specifications: Working length: 4100 mm Stand width: 3650 mm Press force: 220 to CNC control: OPERATOR OPII graphic Color Screen Size: 14" Controlled axes: Y1/Y2; X1/X2; R1/R2; Z1/Z2 Mot. adjustable back gauge Projection: 420 mm Stroke: 180 mm Auto. Crowning Laser monitoring Motor power: 17 kW CE mark Dimensions (length x width x height): approx. 4800 x 2300 x 2900 mm Weight: approx. 16 tons Accessories: various tools