b und c used for sale

grinding diameter: 350 mm grinding length: 1000 mm centre height: 175 mm Control: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: 3,6/3,5 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your machines.Basis: Kellenberger Kel-Varia Baureihe mit Kelco 90 Steuerung. Mechanische Überholung: -komplette Maschine nach Kellenberger Messprotokoll überholt -Neue servicefreundliche Kabine -Neulackierung Elektrische Überholung: -Neue moderne CNC-RUNDSCHLEIFMASCHINEN-Steuerung -Neu aufgebauter Schaltschrank -Neue Antriebstechnik -Austausch sämtlicher elektrischer Leitungen Berus Druckschalter etc. -Neue Absolut-Glasmaßstäbe in x- und z -Neuer Absolut Drehgeber (Bei-B-Achse) Standardausstattung ...

SW BA600-2 CNC machining center with swivel table / built in 1999 / Siemens 840C control / incl. chip conveyor, coolant lubricant preparation and extraction

Dimensions: Length: 7400 mm Width: 4000 mm Height: 3236 mm Extraction capacity: Q = 18000 m³/h P = 15 kW The cabin has a suction machine with filters to suck the powder from the cabin floor. The powder booth is set up in a pit to lower the entire height of the painting line. Manual doors are installed to enter the workpieces into the cabin. The overspray is extracted during powder coating via the floor. On the floor there is a grate for walking on and under the grate there is a second flat floor with automatic self-cleaning system, connected by air ducts with post-filter. A self-cleaning system automatically blows the powder from the bottom to the post-filter (suction machine) and consists of

Oven, doors single-sided, electric Dimensions: 3,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 54 kW Auxiliary heating: electrically indirect via thermoblock

Chemical pre-treatment 3 zones for powder coating with spray ring (automatic) and manual Dimensions: Length: 8000 mm Width: 4500 mm Height: 3500 mm Max. workpiece dimensions (automatic): Length: 6500 mm Width: 1000 mm Height: 2300 mm Max. workpiece dimensions (manual): Length: 6500 mm Width: 2500 mm Height: 2300 mm Tanks are positioned at ground level with a sloping floor. Tank No.1 is thermally insulated and is heated by electric heaters. Achievement: 27 kW. Volume of each tank = 1.00 m³. For degreasing (1st tank), a medium pressure pump is used to operate the 1st spray system. The rinsing phases are also operated by a pump with medium pressure via the 2nd spray system. On the bottom i ...

Oven, doors single-sided, gas Dimensions: 4,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Recirculating air: Q = 12000 m³/h P = 2 x 2.2 kW Heat output: 69 kW Auxiliary heating: Gas indirectly via thermoblock

Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock

Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock

The curing furnace consists of a tunnel furnace in which the workpieces are baked after coating. The furnace is a straight tunnel furnace. The frame is made of steel with insulated panels. The mineral wool insulation becomes 150 mm thick in a special construction to prevent thermal bridges 1 Inner dimension length 7,000 mm Inner dimensions width 1,000 mm Inner dimensions height 2,500 mm 2 Outer dimensions incl. thermoblock, length 7,200 mm Outer dimensions incl. thermoblock, width 1,300/2,300 mm External dimensions incl. thermoblock, height 2,800 mm 3 substructure 1 set of steel profiles 80 x 80 and 40 x 80 mm 4 walls 1 set of double-sided galvanized sheets 1mm, outside RAL 5010 5 Insulation 1 set of rock wool 150mm 75 Kg/m³ 6 Ventilation system 1 set of galvanized steel sheet 7 Temperature max. 220°C 8 fans 1 pc. 7,500 m³/h 9 electric motors 1 pc  ...

Open Powder Spray Stand Dimensions: 2500 x 2250 x 2700 [mm] Extraction capacity: Q = 8000 m³/h P = 5.5 kW Filter: 1 stage: Filter cartridges 4 pieces à Ø 325 x 1000 [mm] 2nd stage: Pocket filter (absolute filter for fine dust) Note: The overspray during powdering is absorbed by the suction unit. The powder spray stand is delivered on rollers and is therefore mobile

Dimensions: Length: 8000 mm Width: 4500 mm Height: 3500 mm Extraction capacity: Q = 18000 m³ P = 15 kW The cab has 2 doors on one side for the insertion/outlet of the workpieces. The components are pushed into the cabin for coating via the overhead transport system. Walls, ceiling and doors are made of panels. The filters positioned on the roof absorb dust and other particles from the outside, thus ensuring clean ambient air in the cabin. The overspray during powdering in the cabin is absorbed by the extraction unit

roller conveyor 2000-640-600 RA2292 Make: Blume Roller width (RB): 600 mm Nominal/outer width (NB): 640 mm Length: 2000 mm Roller diameter: 50 mm Roller distance: 100 mm Motor Roller conveyors: no motor Height frame: 60 mm Scope of delivery: without supports Optionally available: Supports Side guide one and both sides Condition: functional and visually good condition Features: condition: good (used) Conveying length in mm: 3000 Nominal / outside width in mm: 660 Roll width in mm: 600 Roll division in mm: 100 Driven: NO For individual, expert advice, simply get in touch with us. Simply contact us by phone or email. We will be happy to help you plan and implement your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

VSG Cutting table with roller conveyor used Manufacturer: LISEC/ BYSTRONIC Year: 1996 Cutting width max. approx. 306 cm Dimensions cutting table approx. 7 m, 3.8 x 1.1 m; Dimensions roller conveyor approx. 6 x 3 x 1.1 m; The roller conveyor can be tilted hydraulically. The plant has been dismantled Changes and errors in the technical data, specifications and prices as well as prior sale reserved.

VSG glass cutting table with roller conveyor and conveyor belts used Manufacturer: BYSTRONIC Year: 1996 Cutting width max. approx. 306 cm Dimensions cutting table total approx. 8 x 5 x 1.8 m Dimensions roller conveyor approx. 6 x 3 x 1 m The roller conveyor can be tilted hydraulically Conveyor belt approx. 6 x 3 x 1 m Conveyor belt approx. 3 x 3 x 1 m Table approx. 2.7 x 3.5 m The plant has been dismantled Changes and errors in the technical data, specifications and prices as well as prior sale reserved.

Used centrifuge made by Alfa Laval type AFPX 407 BGP-74. Hydraulic capacity - maximum 5 m3/h. 2 pieces available.

- Totally overhauled machine, with a NEW Control + New Crystal Rules - Travel (X x Y x Z): 380 x 380 x 255 mm - Number of tool stations: 6 - Working area (X x Y x Z): 700 x 350 x 2 mm - Max. workpiece weight: 75 kg - Max. spindle speed: 5.000 - 3.

With ByTrans V2 head Upgrade - Laser Type: fiber - Working area (X x Y x Z): 3.100 x 1.580 x 100 mm - Max. workpiece weight: 1.100 kg - Positioning speed X/Y: 120 m/min - Simultaneous positioning speed: 169 X+Y m/min - Laser Output: 6 kW - Maximum material thickness mild steel: 25 mm - Maximum material thickness brass: 15 mm - Maximum material thickness cupper: 12 mm - Maximum material thickness stainless steel: 30 mm - Maximum material thickness aluminium: 30 mm - Control: BYSTRONIC ByMotion - Machine ON Working hours: 53.062 h - Beam ON Working hours: 17.662 h - Electric consumption entire unit: 36 kW - Dimensions (long x wide x high): 12.150 x 5.700 x 3.200 mm - Weight: 19.000 kg

Used machine in good condition. Available for immediate delivery. - Working area (X x Y x Z): 3.048 x 1.524 x 70 mm - Laser Type: fiber - Max. workpiece weight: 890 kg - Positioning speed X/Y: 100 m/min - Simultaneous positioning speed: 140 X+Y m/min - Laser Output: 3 kW - Maximum material thickness brass: 6 mm - Maximum material thickness mild steel: 20 mm - Maximum material thickness cupper: 12 mm - Maximum material thickness stainless steel: 30 mm - Maximum material thickness aluminium: 12 mm - Control: BYSTRONIC ByMotion - Machine ON Working hours: 33.318 h - Beam ON Working hours: 19.925 h - Weight: 12.000 kg - Dimensions (long x wide x high): 10.150 x 3.250 x 2.500 mm - Electric consumption entire unit: 21,4 kW

Used machine in good condition. Available for immediate delivery. - Rapid Traverse (X x Y x Z): 30.000 mm/min - Rapid Traverse (X x Y x Z): 650 x 400 x 305 mm/min - Number of tool stations: 22 - Spindle taper: BT-30 - Spindle power : 7,4 kW - Max. spindle speed: 16.000 rpm - Max. tool diameter: 80 mm - Max. tool weight: 3 kg - Coolant tank capacity: 200 l - Dimensions (long x wide x high): 3.248 x 1.837 x 2.696 mm - Weight: 3.500

Unused Control UNIROB B4 (8.4 TFT touch screen) X axis=1000 (39.4) with servo motor Y axis=1000+1000 (78.7) with servo motor Z axis=4000 (127.5) with servo motor Movement interpolation. Repetition accuracy of +/- 0.1 mm. Maximum weight including gripper: 20 kg. Pneumatic pressure: 6 bars Maximum speed: 3,000 mm/s. Interface: EUROMAP 67 - Interface: EUROMAP 67 - Control: UNIROB B4 - Stroke (X): 1.000 (39,4) with servo mm - Stroke (Y): 1.000+1.000 (78.7) with servo mm - Stroke (Z): 4.000 (127,5) with servo mm - Take-out speed: 3.000 mm/s - Payload: 20 Kg

Nutmaschine - Creasing machine E. Bickel HK3/61 Year 1980 - Serial-No. 442109 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Buchdeckenrundemaschine - Case Rounding Machine Hunkeler BDR 40 --complete clean and painted-- Serial-No. 26964 Output 250 - 300 pcs/h Spine width 10 - 120mm Spine length up to 450mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Nut- und Perforationsmaschine / Creasing and Perforation machine E. Bickel 3/68 Serial-No. 8423 Arbeitsbreite / Working width max. 680mm Inklusive Nut- und Perforationswerkzeug / Include Creasing and Perforation tools Elektriker Antrieb - Fußpedal Eletric Operation - foot pedal Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Bosch CC 220N 074031 CNC Control Servo Power Supply for Trumpf Laser

BÜHLER MWSB-100 dosing screw conveyor for weighing 100 mm diameter, length 2.75 m Engine 0.75 kw, rpm 107 Thread in the inlet progressive, inlet ø 390 mm, Outlet ø150 mm with pneumatic outlet Very good condition

• Top sorting conveyor, width 130 mm, length 600 mm • Lower sorting conveyor, width 225 mm, length 700 mm • Adjustable belt speed • Feed hopper with adjustable vibration • 2 sorting lights • Various deflection rollers for turning tablets through 180 degrees for different tablet thicknesses: - diam. 110 mm for tablet thickness approx. 5 mm - diam. 115 mm for tablet thickness approx. 7 mm - diam. 118 mm for tablet thickness approx. 9 mm - diam. 120 mm for tray thickness approx. 10 mm - diam. 125 mm for tray thickness approx. 12 mm • Drive 220V/50Hz

Dosing screw conveyor BOSCHE 150 mm diameter Length 1.30 m Engine 1,5 kw 32 rpm right-hand thread, slope 110, at the outlet slope 150, Sliding Inlet 270 x 680 mm, outlet 170 x 170 mm Review and test run in our qualified workshop done Good condition

Radiator Brand: Hydac Model : OK-ELH 10/1.0/H22/1/S/BT45/So10 3253734 The radiator is NEW and fully functional, see pictures for more details.

Key data: 1500 mm, 220 mm, 1700 mm

1 pc. used crankshafts & camshafts - cylindrical grinding machine Make BERCO Model LYNX 2000 Year of construction 2013 Specifications Max. grinding diameter for recirculating grinding 220 mm Max. grinding diameter for cylindrical grinding 300 mm Max. workpiece weight between the tips 150 kg Center height above table 270 mm Center width 1700 mm Max. sanding length 1300 mm Diameter of the chucks 180 mm Tailstock quill path 50 mm Max. grinding wheel diameter 660 mm Min./Max. Grinding Wheel Width 20/80 mm Max. circumferential speed 35/80 m/sec. Grinding spindle head (X-axis) Final drive with linear motor - travel 490 mm Measuring device optical scale resolution 0.0001 mm Workpiece head (C-axis) Workpiece spindle speed range 1 - 1000 rpm. Encoder Measurement Range - Resolution 0.0001 degrees Table (Z-axis) Final drive with linear motor Measuring device optica ...

Feeding device / bunker for logs, friezes etc. Filling of the bunkers with a forklift from the front Bunker capacity: approx. 5 m3 Logs, friezes or the like can be filled in bulk. The application is carried out via a hydraulically swivelling tilting device. Various conveyors are included in the scope of delivery. These are 2 identical lines that are also offered individually. 1 line was in use for about 1/2 year, the 2nd line is as good as new. See photos

TO WHOM IT MAY CONCERN ; WE VE USED IN STANDART SIZE CONDATITION OF CRANKSHAFT OF ULSTEIN BERGEN KVGB-16 AT OUR STOCK THE CRANKSHAFT JOURNALS ARE IN STD SIZE LIMITS. IF YOU VE ANY FURTHER QUESTIONS PLS DO NO HESITATE TO CONTACT WITH US . BYE THE WAY WE VE ALSO BELOW LISTED MAJOR PARTS OF KVGB-16 ENGINES CYLINDER HEADS / PISTONS/ CON RODS / FUEL PUMPS / EXH GAS TURBOCHARGERS / OIL PUMPS / FUEL FEED PUMPS / WATER PUMPS ETC ETC AT EX STOCK. IZMIR TURKEY Capt. Ayhan Ugurluba With Kind Regards ; Aliaga Marine Services E mail: info/aliagamarine.com Phn/Fax:+90 232 618 03 85 Mobile: +905556084850 aliagamarine.com TURKEY

Very nice and young complete Ammonia Bitzer screw pump system. The pump system exists out of one Bitzer OSNA8571K screw compressor, a 110 kW WEG E-motor, oil separator, Low pressure separator, economizer, air-cooled oil cooler, air-cooled condenser and a control panel with Siemens PLC. The Bitzer compressor is driven by a 110 kW Vacon inverter. Capacity is 91kW at 60Hz and -35/+40°C (with 50Hz capacity is 75kW). All documentation is available. Also visit our website: used-refrigeration

Key data: 508 mm, 406 mm, 406 mm

Coordinate measuring machine X 508 mm Y 406.4 mm Z 406.4 mm Software: CMM Manager or Verisurf Probing System: Renishaw PH10T/TP20 Controller Type: Mitutoyo UCC200 All information without guarantee Attention: The measuring machine has PC damage, but otherwise the structure is perfect. Dongle is available Sold as a defect! New price was approx. 38,000.00 euros

Key data: 1000 mm, 500 mm, 500 mm

Machine Details Stock-No. 1105-04036 Type of machine Machining Center - Vertical Make BRIDGEPORT Type vmc 1000/22 Year of manufacture 2000 Type of control CNC Storage location FRANCE Country of origin UK Delivery time immediately Freight basis ex stock HAGUENAU FRANCE Price 14500 EUROS Technical details X-Travel 1000 mm Y-Travel 510 mm Z-Travel 600 mm control HEIDENAHAIN TNC 430 table surface area 1150 x 490 mm Rapid Traverse 30/30/30 m/min turning speed range 12000 rpm power capacity - milling spindle 13 kW No. of tools in the magazine 30 Stück Additional information CNC HEIDENHAIN TNC 430 Synchronised tappin - boxway system 3 axis - RS-232 interface WITH CHIP CONVOYER

Table Size 1700 x 710 mm Headstock Travel 810 mm (Z-axis) Height of the machine 4000 mm Table longitudinal displacement 1600 mm (X-axis) Table transverse travel 910 mm (Y-axis) Spindle to tabletop 150 - 960 mm Distance from the floor to the table 1150 mm Distance between spindle center and column front 825 mm T - Groove No. 5 T - Groove Size 18 mm T - Groove Pitch 125 Max. load on the table 2000 kg Spindle cone BT-40 Hourly spindle speed 6000 rpm Footprint (L x W) 4300 x 3400 mm Weight of the basic machine 14500 kg Total connected load 40 kVA (basic standard machine), 50 kVA (basic standard machine with high power

"The BMV60+ redefines the standards for precision machining! The rigid structure, small footprint and precise spindle ensure consistently high quality of performance. The high speed and feed rate meet the criteria necessary for cost-effective processing." "The arm tool magazine uses variable pocket coding. Linear guideways, variable speed AC spindle drives, and a digital drive CNC system are some of the standout features of this BMV60+ series machining center." Unique features: Rigid column technology Modular construction CAE-based optimal structural design for thermal stability "T20 - 20 Tools Roof/Carousel Magazine Carousel Magazine Designed to adapt to different types of coolant and chip systems High-quality spindle on precision bearings eliminates vibration during heavy cutsModel BMV-60 Travel of the X-Y-Z axis 1050 x 610 x 610 mm Spindle performanc ...

Cap conveyor, feeding system, closure conveyor, closure conveyor system, dosing container, crown corker, screw caps. 4 chambers. Conveyor bunker silo for crown corks screw caps conveyor conveying system, 4 chambers, cabins, boxes.

ECKERT SZAFIR BL2 plasma cutting machine was built in 2022 in Poland by Eckert AS Sp. z o.o. The machine, designed for precision cutting sheet metal made of structural steel, stainless steel and aluminium, is distinguished by its large 6 metre long and 2 metre wide sectional work table. The large area of the table makes it possible to efficiently machine a single oversized workpiece or multiple sheets at the same time, guaranteeing a high level of user comfort through the ongoing elimination of contamination. In addition, the portal structure based on a welded steel profile ensures excellent stability of the machine geometry, which does not become unstable under heavy loads. The SZAFIR BL2 plasma cutting machine has worked approximately 867 hours to date. Technical specifications of the ECKERT SZAFIR BL2 plasma cutting machine - CNC controller: ECS 872 - work table dimensions (L x W ...

BLM-ADIGE JUMBO LT14 tube laser cutting machine was built in 2014 in Italy by BLM S.p.A. The machine’s high versatility and extensive machining capabilities make it the perfect choice for precision machining of tubes, open profiles, I-beams and special profiles of large dimensions. It will significantly reduce the cost of producing a single component and improve the quality of cutting compared to other technologies available on the market. The BLM-ADIGE LT JUMBO 14 3D tube laser cutting machine performs machining fully automatically, without the need for retooling or manual adjustments. Once the workpieces have been fed in, the loading unit with conveyor system segregates them according to cross-section, diameter and length. The workpiece is then moved towards the work area, where it is held by three special spindles that eliminate uncontrolled movements and guarantee more precise,  ...

WE SELL AN STUNNING NICE CONDITION CNC BIGLIA WITH TOOLS AND ACCESSORIESS CONDITION IS AS ALMOST NEW. VERY LITLLE USED. FANUC SERIES 18-T Maximum turning diameter: 520 mm Maximum turning length: 500 mm Bar turning diameter: 80mm X axis travel: 210 + 5 Z axis travel: 500 + 10 Spindle speed: 4000 rpm Spindle motor: 11-15 Kw (50%) Spindle connection: ASA 6 Spindle hole: 80 mm Self-centering diameter: 250 mm Turret: number 12 stations Tailstock: CM 4 Dimensions: 3500 x 1670 x 1650 mm Weight: 4600 Kg HOLE TROUGH SPINDLE: 82 mm YEAR:1997

• \cf1Slim design (space requirement only 0.3 square metres) with electromechanical lift drive • Permissible load 1,000 kg • Lift mast with floor and ceiling bearing (included in scope of delivery) • Overall height 3,700 mm without ceiling bearing • Overall height 3,857 mm with ceiling bearing for room height 4,007 mm • Operation via remote-controlled touch panel outside the danger zone • Jog mode and semi-automated process sequences through the use of a microcontroller with touch panel visualisation • Motor with spring-applied brake • Button for operating the discharge flap • Button for activating the vibrator • Safety catch to prevent hazards caused by sudden and unintentional dropping of the load arm • Load support for Bohle container MCG 1200 and MCG 1600 (container not included in the scope of delivery) • Insertable drum frame with load turning gear for 200 ...

• Slim design (space requirement only 0.3 square metres) with electromechanical lift drive • Permissible load 1,000 kg • Lift mast with floor and ceiling bearing (included in scope of delivery) • Overall height 3,700 mm without ceiling bearing • Overall height 3,857 mm with ceiling bearing for room height 4,007 mm • Operation via remote-controlled touch panel outside the danger zone • Jog mode and semi-automated process sequences through the use of a microcontroller with touch panel visualisation • Motor with spring-applied brake • Button for operating the discharge flap • Button for activating the vibrator • Safety catch to prevent hazards caused by sudden and unintentional dropping of the load arm • Load support for Bohle container MCG 1200 and MCG 1600 (container not included in the scope of delivery) • Insertable drum frame with load turning gear for 200 l M ...

H.Biaugeaud A404 HB Cheese grater Stainless, previously used for grating cheese, two grating attachments, mobile, 3Ph

Continuous melt filter The Berlyn Corporation, today: Berlyn ECM S/N 109F160

Vertical machining center TC-32BN QT :::TECHNICAL SPECIFICATIONS::: CNC Model: Brother - CNC Version: B00 - Tool Holder: BT 30 - Spindle Power: 11Kw - Number of Spindle Revolutions: 12000 Number of tools: 26 - X-axis travel: 550mm - Y-axis travel: 400mm - Z-axis travel: 415mm - Rapid feeds for linear axes X Y Z: 70m/min Guides: roller CNC divider: yes Divider brand and model: No. 2 NIKKEN Rotation: Continuous Pallet change: yes Pallet size: 600 x 425mm Maximum allowable load: 200Kg Round pallet: yes High refrigerant pressure: yes Chip conveyor: belt Machine equipment: Renishaw probe ready :::D DIMENSIONS AND WEIGHT::: Length: 1890mm Width: 3669mm Height: 2360mm Weight: 4600Kg

Machine for the processing of mixed waste cables, especially with fine conductors and stranded cables, The plant was most recently used for the post-cleaning of residual plastics from other cable recycling plants. Thanks to the rotor system with the 24 knife segments and the large flywheel masses, the system is also suitable for manual operation. The machine has a cooling unit that optimizes the granulator with a flow temperature of 0.5 °C for the use of heat-sensitive cables, such as NYM, etc. The control electronics of the system enable fully automatic operation in a line with pre-shredder, conveyor belt, dosing accumulator, etc. The machine includes several sets of knives and different sieves. In conjunction with a suitable pre-shredder, the system can process up to approx. 250 kg of old cable. The system was completely overhauled by us and equipped with new tools and par ...

2 pieces of used BIZERBA slicers, type: VS 8 More pictures and information on request. Visits and test runs are possible by arrangement.

BUSELLATO machining center model JET MASTER 5WF XL with 5 axes: - useful axis stroke 5500 x 1900 mm - Useful working range 4650 x 1555 mm - workpiece passage 240 mm (data to be verified) - automatic tables with CNC positioning - 8 bars each with 4 suction cups, and 2 vacuum pumps - with 4 lifts - devices for load assistance - with front safety mats and integrated scrap unloading belt - GENESIS EVOLUTION electronic control with PC/PLC, based on Windows operating system and with 3D editor (CAD – DXF – XLS files) - total installed power KW 25, volt 380 - machine according to CE standards, year 2007 Operating units: - 5-axis milling unit, with: electrospindle with power KW 14, HSK63F connection 24-position rear tool magazine 2-position side magazine, for blade unit and for Large tool - TFR18 drilling unit, power KW 1.7, with: 7 X vertical mandines  ...

Compressed air tank up to 11 bar, volume 500L

x-travel: 20000 mm y-travel: 2800 mm z-travel: 1050 mm control: Heidenhain 530i taper ISO: 50 P.D.B. spindle speeds: 0 - 2000 mm voltage: 380 V total power requirement: 30 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.